← 044/046 · MS 440/460/461

Stihl 1128 · Section H · 8 of 16 · 23 parts

Rewind starter

Fits 046.

Parts diagrams →

Historical fitment & changes (4) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11011121314151617181922020212245679
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (23)

PosPart numberDescriptionQty
1 1128 080 1812 Fan housing 1
2 0000 967 2035 Nameplate STIHL 1
4 1110 084 9102 Bushing 1
5 0000 958 0607 Washer 1
6 9416 868 6530 Hollow rivet 6.5x0.5x6.8 1
7 1128 080 6500 Axle 1
9 1129 190 0601 Rewind spring 1
10 1128 195 0400 Rope rotor 1
11 1128 190 3400 Starter grip ElastoStart Ø 3,5 mm 1
12 1128 190 2900 Starter rope Ø 3.5 mm 1
13 1125 195 7200 Pawl 2
14 0000 958 0923 Washer 1
15 1128 195 3500 Spring 1
16 1128 084 7801 Segment 1
17 9022 313 0660 Spline screw IS-M4x12 2
18 1121 195 3400 Starter grip 1
19 1113 195 8200 Starter rope Ø 3.5x960 mm 1
20 9022 371 1020 Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 3
21 1128 080 7500 NLA Cover plate option 1
22 9022 313 0660 Spline screw IS-M4x12 option 2
Not numbered on the diagram — assemblies, kits and options
— 1128 080 2104 Fan housing with rewind starter 1
— 0000 930 2267 Starter rope Ø 3.5 mm / 28 pieces not illustratedoption 1
— 0000 930 2203 Starter rope Ø 3.5 mm x 30.5 m not illustratedoption 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Historical fitment · 046

046: Plastoform refitting and workshop-tool limits

Re-engage the existing polymer thread and tighten with a torque wrench; the T-handle is release-only on Plastoform screws.

  • For refitting a Plastoform screw, rotate counterclockwise until it drops into the existing thread, then tighten clockwise to the specified torque. This avoids forming a second thread; no new-hole torque is supplied here.
  • The QI-T27x 150 T-handle is for releasing only on Plastoform screws. The roster calls for a torque wrench when tightening them. Optical/acoustic signalling is specifically noted for wrench 0302 and 0312.
  • The lower wrench range is printed as 0.5–18 Nm (0.325–13.5 lbf.ft), the higher as 6–80 Nm (4.5–60 lbf.ft). Preserve printed units/rounding; these ranges are not component torque values.
  • Hot air is described as an aid to releasing adhesive-secured screws, with explicit care around polymer components. No temperature or heating duration is specified.
  • The assembly tube 1117 890 0900 appears twice, once for brake springs and once for clutch springs. The stand/clamping-bar pairing is historical 046 guidance, not resolution of the later support-kit screw conflict.

Source: TI 46/1995, p. 8 · TI 46/1995, p. 12 — 4.1 remarks and5.3 continuation: general tools and existing threads.

Part numbers (17)
  • 1117 890 0900 — Assembly tube, brake and clutch springsListed tool application · 046
  • 5910 893 0501 — M8 bar-stud pullerListed tool application · 046
  • 1111 890 6400 — Ignition air-gap gaugeListed tool application · 046
  • 1116 893 4800 — Rewind-spring assembly toolListed tool application · 046
  • 5910 893 8800 — Fuel-pickup assembly hookListed tool application · 046
  • 5910 890 3100 — Assembly standListed tool application · 046
  • 5910 890 2005 — Clamping bar for mounting sawListed tool application · 046
  • 5910 890 0301 — Torque wrench, lower rangeListed tool application · 046
  • 5910 890 0302 — Torque wrench, lower range with signalListed tool application · 046
  • 5910 890 0311 — Torque wrench, higher rangeListed tool application · 046
  • 5910 890 0312 — Torque wrench, higher range with signalListed tool application · 046
  • 5910 890 2400 — QI-T27x 150 T-handleListed tool application · 046
  • 5910 890 8210 — Electrical connector crimping toolListed tool application · 046
  • 1110 893 4500 — Flywheel pullerListed tool application · 046
  • 5910 893 5608 — 13 mm flywheel-nut socketListed tool application · 046
  • 5910 893 5613 — 19 mm clutch socketListed tool application · 046
  • 0812 542 2104 — T27x 125 IS screwdriverListed tool application · 046

Historical fitment · 046

046: original servicing aids and adhesive distinctions

Lubricants have separate stated applications; Loctite 242,270 and 649 are not presented as interchangeable.

  • Lubricating grease 0781 120 1111 is listed for oil seals, oil-pump drive and sprocket bearing. The same application column also prints “Cleaning crankshaft stub” without a separately named cleaner. Preserve that anomalous row; do not infer grease is a cleaning solvent.
  • Special lubricant 0781 417 1315 is for the rope-rotor bearing bore and starter-cover rewind spring. Multipurpose grease 0781 120 1109 is for the ignition module high-voltage output.
  • The electrician’s repair kit has no contents/application detail on this page. Gasket panel 0457 281 1704 is labeled 044/046, not a claim that their cylinder gaskets interchange.
  • The source lists medium-strength Loctite 242 and high-strength 270/649. Component-specific page 11 remarks determine which is called for; later formulation equivalents are not established.

Source: TI 46/1995, p. 9 · TI 46/1995, p. 11 — 4.2 and5.3 remarks: servicing aids and adhesive assignments.

Part numbers (5)
  • 0781 120 1111 — Lubricating greaseHistorical servicing aid · 046 roster; no current substitute inferred
  • 0781 417 1315 — STIHL special lubricantHistorical servicing aid · 046 roster; no current substitute inferred
  • 0000 007 1013 — Electrician’s repair kitHistorical servicing aid · 046 roster; no current substitute inferred
  • 0781 120 1109 — STIHL multipurpose greaseHistorical servicing aid · 046 roster; no current substitute inferred
  • 0457 281 1704 — Gasket panel 044/046Historical servicing aid · 046 roster; no current substitute inferred

Service note · 046

046: small-fastener torques, adhesives and ignition washer

The ignition-module screws require both Loctite 242 and a washer; nearby screws have different requirements.

  • These are historical TI 46/1995 page 11 fastener-specific values, not universal torque by thread diameter. No fastener part number is supplied. Printed lbf.ft equivalents are retained alongside Nm.
  • Generator IS-M4×12: 3.5 Nm (2.6 lbf.ft), Loctite 649. Chain-tensioner cover plate IS-M4×8: 3 Nm (2.2 lbf.ft).
  • IS-M4×12 oil-pump cover at sprocket side: 3 Nm (2.2 lbf.ft); brake-band/crankcase: 3 Nm (2.2 lbf.ft), Loctite 242; oil pump: 3.5 Nm (2.6 lbf.ft).
  • IS-M4×12 segment/fan housing: 2.5 Nm (1.8 lbf.ft); sprocket-side crankcase cover: 3 Nm (2.2 lbf.ft).
  • M5 SK6 collar nut for carburetor/filter base/flange: 6 Nm (4.4 lbf.ft), remark 3/Loctite 270. The table calls the fastener a collar nut although its remark generically says screw; neither label is silently changed.
  • Fan housing IS-M5×20: 7 Nm (5.2 lbf.ft). Ignition module/crankcase IS-M5×20: 7 Nm (5.2 lbf.ft), Loctite 242 AND a washer under the screw head. Do not transfer this washer requirement to every M5 screw.

Source: TI 46/1995, p. 11 — 5.3: M4 rows, intake collar nut, fan housing and ignition.

No additional parts-table entry added.

Service note · 046

046: limited 044 assembly inheritance, not blanket interchange

The release carries over clutch, rewind starter and chain brake from 044; other parts are described as revised.

  • The source says 044 repair times also apply to 046, but gives no numeric times. Those allowances cannot be reconstructed from this page.
  • Only clutch, rewind starter and chain brake are named as taken from 044. All other parts are described as revised/new and the reader is directed to the IPL. This is a release-level assembly statement, not proof that every internal part or later revision interchanges.
  • The document is dated September 5,1995. That evidence date is not a serial changeover, production start for every market, or the 2026 review date.

Source: TI 46/1995, p. 12 — 5.4 and6: repair times and spare-parts scope.

No additional parts-table entry added.

Wrong number or missing part for the 046? Report a correction →