Stihl 1128 · Section M · 12 of 16 · 37 parts
Carburetor HD-8A, HD-9A
Fits 046.
Historical fitment & changes (9) — includes parts and conditions not shown on this drawing.
Parts (37)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4116 121 5100 | Inlet needle | 1 |
| 2 | 4116 121 5000 | Inlet control lever | 1 |
| 3 | 1128 122 3002 | Spring | 1 |
| 4 | 1113 121 9200 | Spindle | 1 |
| 5 | 1114 122 7400 | Round head screw | 1 |
| 6 | 4117 122 9402 | Plug | 1 |
| 7 | 1128 121 5602 | Fixed jet 0.70 Fitment / change note → → replaced by 1128 121 5603 TI 47/1997 | 1 |
| 8 | 1128 129 0906 | Gasket | 1 |
| 9 | 4116 121 4700 | Metering diaphragm | 1 |
| 10 | 1128 121 0801 | End cover | 1 |
| 11 | 1121 122 7101 | Screw | 4 |
| 12 | 1114 121 7800 | Strainer | 1 |
| 13 | 4116 121 4800 | Pump diaphragm | 1 |
| 14 | 4116 129 0902 | Gasket | 1 |
| 15 | 1127 122 3205 | Torsion spring | 1 |
| 16 | 1127 120 7100 | Throttle shaft with lever | 1 |
| 17 | 1117 122 9000 | E-clip | 1 |
| 18 | 1128 121 3302 | Throttle shutter | 1 |
| 19 | 1115 122 7400 | Round head screw | 1 |
| 20 | 1127 122 3200 | Torsion spring | 1 |
| 21 | 1127 120 7200 | Choke shaft with lever | 1 |
| 22 | 1123 122 9000 | E-clip | 1 |
| 23 | 1122 121 2900 | Choke shutter | 1 |
| 24 | 1110 122 7400 | Round head screw | 1 |
| 26 | 1127 122 6200 | Idle speed adjustment screw | 1 |
| 26 | 1127 121 0800 | End cover | 1 |
| 27 | 1114 122 7100 | Screw | 1 |
| 28 | 1128 121 5403 | Valve jet | 1 |
| 29 | 1127 122 6700 | High speed adjustment screw | 1 |
| 30 | 4116 122 6800 | Low speed adjustment screw | 1 |
| 31 | 4116 122 3001 | Spring | 2 |
| 33 | 1128 122 7101 | Screw | 1 |
| 34 | 1128 122 9301 | Clip | 1 |
| 35 | 1128 121 8602 | Washer | 1 |
| 36 | 1128 121 8603 | Washer | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | not sold separately | Carburetor HD-8A no longer available from factory | 1 |
| — | not sold separately | Carburetor HD-9A no longer available from factory | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Historical fitment · 046
046: carburetor revision without a new part number
TI 25/1996 documents a smaller semi-fixed jet and revised carburetor markings, while the complete carburetor part numbers remain unchanged.
- This 046 change replaces the 0.72 mm semi-fixed jet with 1128 121 5602 (0.70 mm). Applies to the carburetor variants listed here, not every 046 carburetor.
- HD-8 → HD-8 A: 1128 120 0610; HD-9 → HD-9 A: 1128 120 0613. The part number alone does not identify the internal jet revision.
- Introduction was in progress; no serial cutoff is supplied. This is a historical configuration record, not an instruction to rejet unrelated carburetors.
- Original046 complete carburetors include jet item2 (0.72mm); revised HD-8A and HD-9A include item4 (0.70mm). The section2 arrow locates the semi-fixed jet; it is not an H/L mixture-adjustment setting.
- Summary remark1 says complete carburetors are supplied only with the modified semi-fixed jet. Remark2 says the original separate jets are no longer supplied from the factory. This historical supply rule does not prove current stock or authorize arbitrary re-jetting; no removal procedure or torque is printed.
Source: TI 25/1996, p. 2 — Complete section2: jet-location drawing, four designation changes, all11 model-specific summary items, inclusion keys and both availability remarks.
Part numbers (4)
- 1128 120 0610 — HD-8 / HD-8 A carburetorSame number, revised internals · 046; check type marking and jet revision
- 1128 120 0613 — HD-9 / HD-9 A carburetorSame number, revised internals · 046; check type marking and jet revision
- 1128 121 5600 — Semi-fixed jet 0.72 mmOriginal equipment · 046 carburetors listed in this TI
- 1128 121 5602 — Semi-fixed jet 0.70 mmNew version · 046 revised carburetors listed in this TI
Conditional replacement · 046
046 arctic: thermostat moved to the heater
The arctic configuration changed to the standard HD-8 A carburetor together with a new heating element carrying the thermostat and an additional gasket.
Later reviewed guidance: 046 arctic: 8 Ohm heater and retained replacement element
X 37 180 486 — Introduction of the combined carburetor/heater arrangement for the specified arctic variant.
- Applies to 046 arctic, not a blanket carburetor substitution for all 046s.
- New heating element 1128 430 6000 and gasket 1128 129 1100 accompany the new carburetor arrangement. The gasket is fitted between carburetor and heating element.
- The older 1128 434 5101 heater and 1128 430 0501 thermostat remained available for older machines in this TI; the new thermostat is not listed as a separate service item.
- X 37 180 486 is the introduction of this combined arctic configuration, not a model-identification range or permission for an unmatched retrofit.
- The thermostatic switch moves from the carburetor end cover to the heating element; the respective standard carburetor is then used with the new element. Gasket 1128 129 1100 fits between carburetor and element to improve heat distribution according to the source, not a reproduced temperature measurement.
- The original carburetor 1128 120 0613 includes the thermostatic switch; new heating element 1128 430 6000 includes the new switch. The new-switch table entry is not an orderable number: it is unavailable separately. Original carburetor 1128 120 0613 is no longer factory-supplied; standard carburetor 1128 120 0610 is already in inventory. Retention of older heater/switch spares is not permission for an unmatched retrofit or a current-stock claim.
Source: TI 9/1997, p. 3 · TI 9/1997, p. 4 — Complete section3:model-specific arctic carburetor/heater rows,gasket drawing,serial and all supply remarks.
Part numbers (6)
- 1128 120 0613 — HD-9 A carburetorOriginal arctic configuration · 046 arctic with thermostat on carburetor
- 1128 120 0610 — HD-8 A carburetorNew arctic configuration · 046 arctic only with matched new heating arrangement
- 1128 434 5101 — Heating elementOriginal equipment · 046 older arctic heating arrangement
- 1128 430 0501 — Thermostatic switchOriginal service part · 046 older arctic arrangement; not the new integrated thermostat
- 1128 430 6000 — Heating element with thermostatRequired companion · 046 revised arctic heating arrangement
- 1128 129 1100 — GasketRequired companion · Between carburetor and new heating element
Conditional replacement · 046
046: carburetor replacement depends on equipment
TI 47/1997 distinguishes HD-14 service replacements for older non-EPA machines from HD-16 carburetors for the EPA-equipped version.
- Older 046 without EPA equipment: replace HD-8A (1128 120 0610) with HD-14 (1128 120 0624).
- The EPA-equipped 046 uses HD-16 (1128 120 0623). Do not treat the two replacement branches as unconditional substitutes.
- The source requires new limiter caps after removal during repair; adjustment and cap-fitting procedure remains in the TI, not inferred from a parts match.
- Introduction is stated as the start of EPA-version production, with no numeric serial cutoff.
- Except for limiter caps and adjusting screws, the non-EPA service HD-14 is stated to be technically the same as its EPA counterpart HD-16; this does not remove the equipment-dependent replacement rule.
- The summary lists original HD-8A with items 7, 9, 10 and 12; new HD-14 includes 7, 9, 10, 12, 14 and 15; EPA HD-16 includes 8, 9, 11, 13 to 16. These are printed inclusion lists, not permission to infer omitted items.
- Original complete carburetor no longer available from the factory; all other parts remain as before. These are dated 1997 supply statements, not current stock. The separate cap-setting notes retain lean-stop versus screw-seat reference points.
Source: TI 47/1997, p. 2 · TI 47/1997, p. 3 · TI 47/1997, p. 5 — Sections 1–1.7: carburetor and service branches; full section, drawing and summary context reviewed in batch26.
Part numbers (3)
- 1128 120 0610 — Carburetor HD-8AOriginal equipment · 046 original configuration
- 1128 120 0624 — Carburetor HD-14Conditional service replacement · 046 older machine without EPA equipment
- 1128 120 0623 — Carburetor HD-16EPA configuration · 046 EPA-equipped version only
Service note · 046
046: historical carburetor and ignition specifications
The original fuel and ignition settings are release-specific reference data, not universal replacement-carburetor settings.
- The original all-position diaphragm carburetor has an integral fuel pump; standard H and L settings are each one turn open. No carburetor type or limiter configuration is specified, so these settings are not assigned to every carburetor listed on the linked later IPL sheets.
- Fuel capacity is 0.94 l (2 US pt). The 1995 source specifies minimum pump octane 89 unleaded, 50: 1 with STIHL 50: 1 two-stroke oil, and 25: 1 with other brand-name air-cooled two-stroke oils. This is historical formulation-dependent guidance, not a new recommendation for current oils.
- Breakerless electronic magneto ignition: module/flywheel air gap 0.15–0.30 mm (0.006–0.012 in), timing 2.0–3.0 mm (0.080–0.12 in) before top dead center.
- Suppressed Bosch WSR 6 F spark plug: 0.5 mm (0.020 in) electrode gap, M14 × 1.25 thread, 9.5 mm (0.37 in) thread length and printed heat range 200. No alternative plug or STIHL part number is inferred.
Source: TI 46/1995, p. 6 · TI 46/1995, p. 7 — 2.2–2.3: fuel, ignition and spark-plug specification.
No additional parts-table entry added.
Service note · 046
046 C: catalyst fuel and speed limits
Accurate tachometer required; full-throttle limits are 13,000–13,500 rpm.
- For the 046 C catalytic-converter version, corrections to high-speed screw H are permitted only with an accurate tachometer to check that maximum permissible engine speed 13,500 rpm is not exceeded, with a properly tensioned chain. Minimum full-throttle speed must not be below 13,000 rpm. These are not idle-speed specifications or verified measurements.
- The printed fuel requirement is unleaded brand-name gasoline mixed with STIHL 50:1 high-performance two-stroke engine oil or STIHL HT plus 50:1 synthetic engine oil. This records the 1997 catalyst-version instruction, not a new fuel recommendation for every 046 or successor.
- The source also refers to TI11/1993 section1.5, absent from the retained corpus. The locally printed requirement is retained without inventing that missing section. Linked carburetor sheets are navigation aids, not proof that every carburetor variant fits 046 C.
Source: TI 5/1997, p. 2 — Complete sections1.2–1.3.
No additional parts-table entry added.
Service note · 044 / 046
044 / 046 EPA: capped standard setting
H = 3/4 and L = 1/4 open from the lean stop; not from screw seats.
- This note applies to the described EPA HD-17(044) and HD-16(046) carburetors with limiter caps. Factory optimum setting is the standard setting: H = 3/4 turn and L = 1/4 turn open, starting from the lean stop in each case. It is not the uncapped basic setting and not a setting for every HD carburetor.
- The integral stops in the insert bores limit corrections to 270 degrees. Caps are retained by the knurled screw heads and sit flush with the insert, at the bottom of the dome. The source describes this range as permitting high-altitude leaning while limiting enrichment beyond its EPA limits.
- For unsatisfactory high-altitude running, the printed sequence is check standard setting, warm engine, then slight clockwise(leaner) corrections of H and L. Too lean a setting exceeds maximum permissible speed and risks engine damage. No numeric maximum speed or altitude threshold is printed here; no value is borrowed from the046 C catalyst instruction.
Source: TI 47/1997, p. 2 · TI 47/1997, p. 3 — Complete sections1.1–1.3 and cap-stop diagram132TI022.
No additional parts-table entry added.
Service note · 044 / 046
044 / 046 EPA: cap removal and basic setting
Uncapped H and L each start one full turn open from their seats.
- Applies to the described EPA HD-17(044) and HD-16(046) configuration, not every carburetor on these model sheets. Remove caps to replace screws or clean the carburetor. First turn the caps/screws counterclockwise to their stops, then screw puller5910 890 4500 into each cap counterclockwise until it comes off. Do not reuse removed caps.
- After fitting adjusting screws and with caps removed, start with screws against their seats: open H one full turn and L one full turn. This seat-referenced basic setting must not be confused with the capped standard setting measured from lean stops.
- Always fit new caps. Insert with lug positions exactly as drawing132TI023, then push onto screws until flush with insert(1). The source says the resulting position equals the standard setting, but prints cross-reference1.2 where the standard-setting section is1.3. Preserve this reference mismatch; the source drawing remains the lug-orientation reference.
- Set idle speed to2500 rpm with idle-speed screw LA and use a tachometer. This is not the maximum permissible engine speed. This historical procedure does not authorize unattended adjustment or hardware operation.
Source: TI 47/1997, p. 3 · TI 47/1997, p. 4 — Complete sections1.2,1.4–1.4.3; diagrams139TI013 and132TI023.
Part numbers (1)
- 5910 890 4500 — Limiter-cap pullerSpecified service tool · 044 HD-17 /046 HD-16 EPA cap removal
Service note · 044 / 046
044 / 046: EPA label and 50:1 approval context
The1997 approval used50:1; referenced TI27/1997 remains unavailable in this corpus.
- The cover states that the described modifications achieve EPA compliance except sections4.2,5.2 and6.1. There is no body subsection6.1 in this issue: front hand guard is section6 and flush-cut version is7.1. The exception label remains unresolved; do not silently assign an emission role to either change.
- The illustrated factory IMPORTANT ENGINE INFORMATION label states conformity to US EPA Phase1 utility/lawn-and-garden engine regulations and refers to the owner manual for maintenance specifications and adjustment. Its engine-family/type/displacement/date fields are an example, not an observed machine identity or evidence that any repaired machine is compliant.
- Section1.5 says EPA approval was obtained with50:1 fuel/oil mix and no emission measurements are available for other ratios. This is the scope of the original approval evidence, not a claim that alternate ratios were tested or a universal fuel recommendation.
- Cover and sections1.5–1.6 refer to TI27/1997, including Federal Emission Control Systems Utility Engines. TI27/1997 is absent from the retained690-TI inventory and tipages scan filenames; that referenced detail remains a source gap, not proof of absence everywhere.
Source: TI 47/1997, p. 1 · TI 47/1997, p. 4 — Cover compliance statement/label and complete sections1.5–1.6.
No additional parts-table entry added.
Service note · 046
046 arctic: 8 Ohm heater and retained replacement element
The revised element changes shape and thermostat orientation; 1128 430 6000 remains a stated replacement for all 046 arctic versions.
- Section 4 says the previous heating element 1128 430 6000 is replaced in production by a new version. Its shape is optimized for use in several models, its thermostat is turned and its wiring routed accordingly; drawing 132TI030 KN preserves the installation orientation. No rotation angle or list of those other models is specified.
- Both heating-element versions have the same stated resistance, 8 Ohm. This is not either generator-winding resistance (0.8 or 0.6 Ohm), nor a temperature/tolerance-qualified pass/fail test.
- The same section explicitly says heating element 1128 430 6000 will continue to be supplied as a replacement for all versions of the 046 arctic. Preserve that historical service statement alongside section 5’s general ban on mixing old and new parts; do not broaden it to mixed generator/harness/flywheel sets or other models.
- The bulletin does not give a distinct order number for the new production heating element. No number is inferred from later catalog entries or from the shared part prefix. The existing exact-046 carburetor/wiring anchors are navigation only; no new drawing position, universal carburetor fitment or unidentified heater order number is created.
- Applies only to 046 arctic, series 1128. The shared 046 catalog sheets are navigation anchors, not evidence that non-arctic 046, 044 or MS 460 machines use this configuration. Historical source instructions and nominal values are not hardware measurements or current spare-stock claims.
Source: TI 28/1999, p. 1 · TI 28/1999, p. 2 · TI 28/1999, p. 3 — Section 4 heater shape, thermostat and 8 Ohm value; section 5 and summary no-mixing scope.
Part numbers (1)
- 1128 430 6000 — Heating elementPrevious production element; retained replacement for all 046 arctic versions · 046 arctic configuration specified in TI28/1999 only
Wrong number or missing part for the 046? Report a correction →