Stihl 1128 · Section B · 2 of 13 · 33 parts
Cylinder
Fits MS 440.
Historical fitment & changes (9) — includes parts and conditions not shown on this drawing.
Parts (33)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1128 020 1227 | Cylinder with piston Ø 50 mm Fitment / change note → — 70.7 cc | 1 |
| 2 | 1128 030 2015 | Piston Ø 50 mm — 70.7 cc | 1 |
| 3 | 1128 034 3000 | Piston ring Ø 50x1.2 mm — 70.7 cc | 2 |
| 4 | 1128 034 1501 | Piston pin 12x8x35 | 1 |
| 5 | 9463 650 1200 | Snap ring 12x1 | 2 |
| 6 | 1122 025 2200 | Plug Fitment / change note → | 1 |
| 7 | 1128 020 9400 | Decompression valve Fitment / change note → | 1 |
| 8 | 1122 084 1405 | Cover Fitment / change note → | 1 |
| 9 | 1128 029 2301 | Cylinder gasket 0.5 mm | 1 |
| 9 | 1128 029 2302 | Cylinder gasket 1 mm | 1 |
| 10 | 9512 003 3061 | Needle cage 12x15x15 | 1 |
| 11 | 9022 371 1050 | Spline screw IS-M5x25 Fitment / change note → | 4 |
| 12 | 9022 371 1020 | Spline screw IS-M5x20 Fitment / change note → → replaced by 9022 371 1050 TI 30/2004 | 4 |
| 13 | 1128 141 3201 | Cooling plate | 1 |
| 14 | 1125 149 0601 | Muffler gasket | 1 |
| 15 | 1128 140 0600 | Muffler Fitment / change note → | 1 |
| 16 | 1128 145 0803 | Exhaust casing | 1 |
| 17 | 1128 140 0607 | Muffler | 1 |
| 18 | 1128 140 0604 | Muffler | 1 |
| 19 | 1118 141 9006 | Screen | 1 |
| 20 | 1128 145 0804 | Exhaust casing | 1 |
| 21 | 1128 149 0500 | Gasket Fitment / change note → | 1 |
| 22 | 9022 341 0980 | Spline screw IS-M5x16 | 2 |
| 23 | 9022 341 0910 | Spline screw IS-M5x6 | 2 |
| 24 | 9022 341 1300 | Spline screw IS-M6x20 | 2 |
| 26 | 1128 140 0610 | Muffler | 1 |
| 27 | 1128 145 0710 | Inlet casing | 1 |
| 28 | 1128 145 8000 | Sleeve | 1 |
| 29 | 9022 341 1070 | Spline screw IS-M5x30 | 1 |
| 30 | 9022 341 0910 | Spline screw IS-M5x6 | 1 |
| 31 | 1110 400 7005 | Spark plug Bosch WSR 6 F | 1 |
| 32 | 0000 400 7000 | Spark plug NGK BPMR7A | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 1128 007 1050 | Set of gaskets option | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Conditional replacement · MS 440
MS 440: decompression valve function and service precautions
14 Nm valve torque; remove for leakage testing and close before piston locking.
- Decompression valve 1128 020 9400 becomes standard on MS 440; introduction is in progress, with no numerical serial cutoff in this TI. Manually opening it reduces compression during starting; it closes automatically when the engine fires.
- The screwed-in valve consists of body (1) and axially moving plunger (2) with a conical bottom. Three spring-loaded balls (3), offset 120 degrees, retain the upper or lower position. Pressing the plunger down lifts the cone and opens the bore. Cranking releases some gas while the remaining compression stays below closing pressure; ignition raises pressure enough to move the plunger up and seal the bore. No numerical opening or closing pressure is specified.
- Use a standard long-reach 13 mm socket for removal/installation; the specified decompression-valve tightening torque is 14 Nm. For an engine leakage test, remove the valve and seal its cylinder hole with plug 1122 025 2200. This torque is for the valve, not an independently specified plug torque.
- Close the decompression valve before fitting the locking strip to block the piston, to avoid damaging the valve. These are retained service instructions, not evidence of a performed engine test.
- The named model scope is not extended to other models sharing series 1128 or later IPL sheets. Factory supply statements are historical, not current stock. No physical interchange test was performed.
Source: TI 28/2002, p. 1 · TI 28/2002, p. 2 · TI 28/2002, p. 3 — Sections 1–1.2, valve cutaway and summary row 4.
Part numbers (2)
- 1128 020 9400 — Decompression valveNew standard equipment · Only the named model and configuration; see conditions
- 1122 025 2200 — Cylinder plugLeakage-test sealing plug · Only the named model and configuration; see conditions
Conditional replacement · MS 440
MS 440: replacement cylinder and non-decompression plug
Plug the new cylinder on non-decompression machines; conflicting old-cylinder availability is retained.
- Cylinder with piston 1128 020 1227 replaces 1128 020 1226. On a machine without a decompression valve, seal the valve hole with supplied plug 1122 025 2200. The new cylinder includes that plug; fitting this cylinder does not require adding a working valve.
- Unresolved source conflict: section 2 says only the new cylinder is available as a replacement, while summary item 1 carries remark 1 saying the previous cylinder is supplied until factory stocks last. Both are preserved; do not silently change one into a current availability guarantee.
- Modification introduction is in progress. TI 11/2002 is the last-TI pointer, not a shared serial threshold for this cylinder change.
- The named model scope is not extended to other models sharing series 1128 or later IPL sheets. Factory supply statements are historical, not current stock. No physical interchange test was performed.
Source: TI 28/2002, p. 2 · TI 28/2002, p. 3 — Section 2 and summary rows 1–3/remark 1.
Part numbers (3)
- 1128 020 1226 — Cylinder with pistonPrevious; conflicting supply statements · Only the named model and configuration; see conditions
- 1128 020 1227 — Cylinder with pistonNew; includes plug · Only the named model and configuration; see conditions
- 1122 025 2200 — Cylinder plugRequired on non-decompression machine · Only the named model and configuration; see conditions
Conditional replacement · MS 440
MS 440: shroud opening cap and separate dirt cover
The shroud cap and cylinder sealing plug serve different holes.
- Shroud 1128 080 1624 replaces 1128 080 1605. Its valve opening has a raised molded edge to reduce accidental valve operation. The previous shroud is supplied only while factory stocks last.
- On machines without a decompression valve, close the shroud opening with provided cap 1122 084 7100. This shroud cap is not the cylinder sealing plug 1122 025 2200; non-decompression configurations need their respective openings closed as described.
- Cover 1122 084 1405 fits between cylinder and shroud to prevent dirt ingress; the illustration shows its position around the upper cylinder/valve area. It is distinct from both the shroud cap and the cylinder plug. Introduction is in progress without a numerical serial cutoff.
- The named model scope is not extended to other models sharing series 1128 or later IPL sheets. Factory supply statements are historical, not current stock. No physical interchange test was performed.
Source: TI 28/2002, p. 2 · TI 28/2002, p. 3 — Sections 3–4, cap/cover diagrams and summary rows 5–8/remark 1.
Part numbers (5)
- 1128 080 1605 — ShroudPrevious; stocks only · Only the named model and configuration; see conditions
- 1128 080 1624 — ShroudNew; includes cap · Only the named model and configuration; see conditions
- 1122 084 7100 — Shroud opening capNon-decompression configuration · Only the named model and configuration; see conditions
- 1122 084 1405 — Dirt coverBetween cylinder and shroud · Only the named model and configuration; see conditions
- 1122 025 2200 — Cylinder plugSeparate cylinder sealing function · Only the named model and configuration; see conditions
Conditional replacement · MS 440
MS 440: manifold replacement for temperature resistance
Two previous manifolds converge on 1128 141 2203; no temperature limits are supplied.
- Manifold 1128 141 2203 replaces both 1128 141 2200 and 1128 141 2202 to improve resistance to high and low temperatures. Both previous versions are supplied only while factory stocks last.
- The comparison drawing identifies the top section as previous 1128 141 2200 and bottom as new 1128 141 2203; arrows identify the differing illustrated profiles. It does not depict 1128 141 2202 or specify a measured wall thickness, temperature rating or installation orientation rule.
- Introduction is in progress without a numerical serial cutoff. Do not reuse the separate crankshaft serial from TI 11 as this manifold changeover.
- The named model scope is not extended to other models sharing series 1128 or later IPL sheets. Factory supply statements are historical, not current stock. No physical interchange test was performed.
Source: TI 28/2002, p. 3 — Section 5 comparison drawing and summary rows 9–10/remark 1.
Part numbers (3)
- 1128 141 2200 — ManifoldPrevious; stocks only · Only the named model and configuration; see conditions
- 1128 141 2202 — ManifoldPrevious; stocks only · Only the named model and configuration; see conditions
- 1128 141 2203 — Temperature-resistant manifoldNew replacement for both · Only the named model and configuration; see conditions
Service note · MS 440
MS 440 muffler seal: order it separately from muffler 0600
The new seal sits between the upper and lower muffler mouldings.
- Seal 1128 149 0500 is introduced BETWEEN THE UPPER AND LOWER MOULDINGS of muffler 1128 140 0600, as the exploded drawing shows. It is not the cylinder-to-muffler gasket or a blanket gasket application to every muffler listed on the cylinder sheet.
- The seal is NOT INCLUDED in muffler 1128 140 0600 and MUST BE ORDERED SEPARATELY. The summary lists it as a new part with no previous number; do not invent a predecessor or assume the new carburetor assembly includes the muffler seal.
- Introduction is continuous without a numeric serial cutoff. The source gives no muffler-fastener torque, sealant requirement or replacement interval here. Preserve the exact 0600 muffler pairing rather than extending this instruction to catalytic or other muffler variants on the same catalog sheet.
- Historical TI39/2003 English guidance for the specified MS 440 carburetor or muffler configuration; not a universal setting for every MS 440 revision or region. MS 440 C catalytic-converter conditions apply only where explicitly stated. No physical interchange test was performed.
Source: TI 39/2003, p. 4 · TI 39/2003, p. 5 — Section 2 and summary seal row complete.
Part numbers (2)
- 1128 140 0600 — MufflerExact assembly requiring separately ordered seal · MS 440; exact historical configuration stated above
- 1128 149 0500 — Seal between muffler mouldingsNew; not included in muffler 0600 · MS 440; exact historical configuration stated above
Service note · MS 440
MS 440 cylinder mounting: longer inserts without a new crankcase number
The production serial boundary is not enough to choose repair screws.
1 62 936 786 — MS 440 production introduction of longer crankcase inserts and M5x25 cylinder screws; repairs still require actual insert and cylinder-rib inspection.
- From machine number 1 62 936 786, both crankcase halves receive longer threaded inserts and the cylinder mounting changes from M5x20 screw 9022 371 1020 to M5x25 screw 9022 371 1050. The increase is the printed 0.197 in (5 mm). The stated purpose is improved crankcase-to-cylinder fastening.
- The CRANKCASE PART NUMBER REMAINS UNCHANGED. The bulletin does not print a crankcase order number, so none is invented here or selected from the later catalog’s multiple rows. The first-page comparison shows short inserts on the left and longer inserts on the right on both halves.
- The previous M5x20 screw remains available for older machines and short-insert crankcases; it is also explicitly required for the long-insert/ribbed-cylinder repair combination described on page 2. The summary says all other parts unchanged; this does not cancel the cylinder rib restriction or authorize M5x25 in every older saw.
- The summary repeats the same machine cutoff and old-part retention. TI39/2003 is the named preceding MS 440 bulletin; the bibliography and copyright footer add no further component fitment. Historical availability is not a current stock check.
- Historical TI30/2004 English USA guidance for MS 440 cylinder mounting only; not MS 460 or a universal M5 screw rule. Inspect both crankcase inserts and cylinder rib configuration; machine number alone does not identify components after repairs. No physical interchange test was performed.
Source: TI 30/2004, p. 1 · TI 30/2004, p. 2 · TI 30/2004, p. 3 — Production change; crankcase; screw identities; complete summary.
Part numbers (2)
- 9022 371 1020 — M5x20 cylinder screwShort inserts; also long-insert case with ribbed cylinder · MS 440 cylinder mounting; insert and rib restrictions apply
- 9022 371 1050 — M5x25 cylinder screwLong inserts AND cylinder without obstructing ribs only · MS 440 cylinder mounting; insert and rib restrictions apply
Service note · MS 440
MS 440 cylinder screws: check insert dimension a and the cylinder ribs
12 ± 0.5 mm and 17 ± 0.5 mm are illustrated insert dimensions, not screw lengths.
- In the crankcase cutaway, dimension a identifies the illustrated threaded-insert extent. The source pairs a = 0.472 ± 0.020 in (12 ± 0.5 mm) with M5x20 / 9022 371 1020, and a = 0.669 ± 0.020 in (17 ± 0.5 mm) with M5x25 / 9022 371 1050. Preserve the printed metric and inch pairs; these are not 12 mm or 17 mm screw lengths, and no measurement method beyond the drawing is specified.
- The new M5x25 screw may be used ONLY WITH THE LONGER INSERTS. A 17 mm insert is necessary but not sufficient: the cylinder must also lack the obstructing ribs shown as (a) in the separate cylinder figure. Its labels (a)/(b) are configuration identifiers, not the crankcase drawing’s dimension a.
- The screw/crankcase table uses “only” permitted combinations, but the adjacent cylinder repair paragraph explicitly requires M5x20 when a NEW long-insert crankcase is combined with a RIBBED cylinder. Retain this stated exception rather than treating the table alone as a universal prohibition of short screws in long inserts.
- Tightening torque remains the printed 102 lbf in (11.5 Nm). These are inch-pounds, NOT foot-pounds. No revised torque, sealant, threadlocker, tightening order or permission to deepen an insert is supplied. All four cylinder screws must be the same length under the cylinder instruction.
- Historical TI30/2004 English USA guidance for MS 440 cylinder mounting only; not MS 460 or a universal M5 screw rule. Inspect both crankcase inserts and cylinder rib configuration; machine number alone does not identify components after repairs. No physical interchange test was performed.
Source: TI 30/2004, p. 2 — Screws; repair-note dimensions and tightening torque; cylinder exception.
Part numbers (2)
- 9022 371 1020 — M5x20 cylinder screwShort inserts; also long-insert case with ribbed cylinder · MS 440 cylinder mounting; insert and rib restrictions apply
- 9022 371 1050 — M5x25 cylinder screwLong inserts AND cylinder without obstructing ribs only · MS 440 cylinder mounting; insert and rib restrictions apply
Service note · MS 440
MS 440 ribbed cylinder: keep four M5x20 screws even on a new crankcase
Long inserts do not remove the cylinder-rib clearance restriction.
- The cylinder figure marks the ribbed configuration (a) and the configuration without those ribs (b). M5x25 CANNOT be used on the ribbed cylinder (a). It can be used on cylinder (b) only together with the long crankcase inserts required by the adjacent screw note; absence of ribs alone does not permit longer screws in short inserts.
- When a new crankcase WITH LONGER INSERTS is combined during repair with a cylinder WITH RIBS (a), use the SHORTER M5x20 screws 9022 371 1020. This is an explicit repair exception, not an inferred substitution and not permission to grind away ribs or alter screw length.
- To ensure uniform thermal expansion, the cylinder MUST ALWAYS be secured with FOUR SCREWS OF THE SAME LENGTH. Do not mix M5x20 and M5x25 around one cylinder. The source supplies no ribbed/unribbed cylinder order numbers, so this is a physical-configuration condition, not an assignment to an unverified catalog cylinder number.
- Historical TI30/2004 English USA guidance for MS 440 cylinder mounting only; not MS 460 or a universal M5 screw rule. Inspect both crankcase inserts and cylinder rib configuration; machine number alone does not identify components after repairs. No physical interchange test was performed.
Source: TI 30/2004, p. 2 — Cylinder figure and full repair exception; uniform thermal expansion.
Part numbers (2)
- 9022 371 1020 — M5x20 cylinder screwShort inserts; also long-insert case with ribbed cylinder · MS 440 cylinder mounting; insert and rib restrictions apply
- 9022 371 1050 — M5x25 cylinder screwLong inserts AND cylinder without obstructing ribs only · MS 440 cylinder mounting; insert and rib restrictions apply
Service note · MS 440 / MS 460
MS 440 / MS 460: cold-resistant manifold and molded identification
The new manifold serves heated versions; the old one remains for unheated versions.
- Cover identifies MS 440/MS 460, series 1128. Previous manifold 1128 141 2203 is replaced by 1128 141 2204 FOR MACHINES WITH CARBURETOR AND HANDLE HEATING. New manifold is described as extremely resistant to low temperatures; no temperature rating is printed.
- Figure 175TI016 points to the molded identification: old 1128 141 2203 bears 1128/03 OR 1128; new 1128 141 2204 bears 1128/04. These markings identify the manifold revision, not a saw serial number.
- Old manifold 1128 141 2203 REMAINS AVAILABLE for versions WITHOUT carburetor and handle heating. For service, new 1128 141 2204 may also be installed in OTHER VERSIONS where extreme low-temperature resistance is required. This qualified permission is not universal old-part obsolescence or evidence for unnamed044/046/MS 461.
- Summary repeats the replacement with old-part other-model availability and CONTINUOUS introduction. No numeric serial changeover or installation procedure is supplied.
- Historical English 2008 source, not present-day stock or approval for unlisted variants. No numeric serial cutoff is supplied. No physical interchange test was performed.
Source: TI 46/2008, p. 1 · TI 46/2008, p. 2 — MS 440 / MS 460: cold-resistant manifold and molded identification.
Part numbers (2)
- 1128 141 2203 — Previous manifold1128/03 or1128 marking; unheated supply retained · MS 440 / MS 460; source restrictions apply
- 1128 141 2204 — Cold-resistant manifold1128/04 marking; heated/qualified service use · MS 440 / MS 460; source restrictions apply
Wrong number or missing part for the MS 440? Report a correction →