Stihl 1128 · Section A · 1 of 13 · 38 parts
Crankcase, Crankshaft
Fits MS 440.
Historical fitment & changes (14) — includes parts and conditions not shown on this drawing.
Parts (38)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1128 020 2136 | Crankcase Fitment / change note → | 1 |
| 2 | 1128 020 2122 | Crankcase Fitment / change note → → replaced by 1128 020 2136 TI 15/2007 | 1 |
| 3 | 0000 988 5211 | Connector | 1 |
| 4 | 9371 470 2610 | Cylindrical pin 5x18 | 2 |
| 5 | 0000 974 1200 | Notched pin 2.6x8 | 1 |
| 6 | 1128 640 9100 | Valve | 1 |
| 7 | 9503 003 0346 | Grooved ball bearing 6202 Fitment / change note → | 1 |
| 8 | 9523 003 4275 | Grooved ball bearing 15x35x13 | 1 |
| 9 | 1138 664 2400 | Collar screw Fitment / change note → | 2 |
| 10 | 0000 953 6605 | Collar screw M8 Fitment / change note → | 2 |
| 11 | 9022 371 1020 | Spline screw IS-M5x20 Fitment / change note → → replaced by 9022 371 1050 TI 30/2004 | 5 |
| 12 | 1120 162 5200 | Pin | 1 |
| 13 | 1121 162 5205 | Pin | 1 |
| 14 | 1128 162 5200 | Pin | 1 |
| 15 | 1121 162 5200 | Pin | 1 |
| 16 | 1128 084 8302 | Reflector foil | 1 |
| 17 | 1128 647 9405 | Hose | 1 |
| 18 | 1117 640 3800 | Pickup body | 1 |
| 19 | 9640 003 1320 | Oil seal 13x19x4 | 1 |
| 20 | 9640 003 1972 | Oil seal 18x29.6x5/3 | 1 |
| 21 | 9640 951 1972 | Oil seal 18x29.6x5/3 | 1 |
| 22 | 1128 029 0500 | Gasket | 1 |
| 23 | 1128 030 0406 | Crankshaft Fitment / change note → | 1 |
| 24 | 1120 036 8500 | Woodruff key 2x3.7 | 1 |
| 25 | 1124 791 2800 | Stop buffer | 1 |
| 26 | 1125 007 1021 | Spur gear / chain adjusting screw kit | 1 |
| 27 | 9646 945 0490 | O-ring 7x1.5 | 1 |
| 28 | 1125 640 1900 | Tensioner slide | 1 |
| 29 | 1122 664 2200 | Cover plate | 1 |
| 30 | 9041 216 0630 | Pan head screw M4x8 | 2 |
| 31 | 1125 664 1400 | Thrust pad | 1 |
| 32 | 1122 664 4500 | Support | 1 |
| 33 | 1128 664 1001 | Inner side plate 0.9 mm → replaced by 1128 664 1002 TI 12/1994 | 1 |
| 34 | 1128 664 1002 NLA | Inner side plate → replaced by 1128 664 1001, 1128 664 1001 TI 10/2007 option | 1 |
| 35 | 1133 791 5900 | Stop buffer | 1 |
| 36 | 0000 350 0525 | Filler cap | 1 |
| 37 | 9645 948 7734 | O-ring 25x3.5 | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 1128 007 1050 | Set of gaskets option | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Historical fitment · 044 / MS 440
044 → MS 440: 6202 bearing replacement
TI 06/2001 specifies a main-bearing number change to standardize parts inventories.
- The documented 6202 bearing change is 9503 003 0340 → 9503 003 0346.
- Do not apply the 046 serial cutoff from TI 03/1999 to this 044/MS 440 transition; TI 06/2001 says introduction was in progress. This is not an all-bearing replacement rule.
- Introduction is in progress without a numeric serial cutoff; retained edition is english / USA. Historical factory-availability remarks are not current stock information.
- Section 6 states parts-inventory standardization as the reason. Summary item 8 is included in crankcase item 6; remark 1 marks the old bearing no longer available from the factory. No bearing material, clearance, seal specification or new installation procedure is given; designation 6202 alone does not identify every compatible commercial bearing.
Source: TI 6/2001, p. 1 · TI 6/2001, p. 2 · TI 6/2001, p. 3 · TI 6/2001, p. 4 — Complete sections 1–9: 044/MS440 naming and power chronology, split-filter intake, cap operation, matching assemblies, vent construction/function, main bearing, clutch and all 17 summary rows.
Part numbers (2)
- 9503 003 0340 — 6202 main bearingPrevious version · 044 predecessor configuration
- 9503 003 0346 — 6202 main bearingReplacement version · 044 / MS 440 transition
Conditional replacement · MS 440
MS 440: collar screws determine cover compatibility
Old covers without countersunk holes must not be used with new collar screws 1138 664 2400. New countersunk covers accept either collar screw type.
- Old covers without countersunk holes must not be used with new collar screws 1138 664 2400. New countersunk covers accept either collar screw type.
- Crankcase 1128 020 2122 with old screws remains a historical service option for older covers; 1128 020 2136 includes new screws.
- Wrap-around handlebars require the cover with an extended outward-projecting lower section; a countersink alone does not establish wrap-handle suitability.
- When fitting a new cover, replace the lugged side plate with the lug-free version and its specified screw; see the linked sheet note.
- This is a configuration rule, not permission to machine an old cover or infer an unrestricted 044/046 crankcase swap.
- Retained edition: English USA. Introduction is continuous, with no numeric serial cutoff. Historical availability is not current stock or universal regional applicability.
Source: TI 15/2007, p. 1 · TI 15/2007, p. 2 · TI 15/2007, p. 3 · TI 15/2007, p. 4 · TI 15/2007, p. 8 — Sections 1.1–1.3 and summary: model-specific cases/covers, compatibility matrix.
Part numbers (8)
- 1128 020 2122 — CrankcasePrevious version · MS 440; old collar screws
- 1128 020 2136 — CrankcaseRevised version · MS 440; new collar screws
- 0000 953 6605 — Collar screwPrevious version · Old or countersunk covers
- 1138 664 2400 — Collar screwNew version · Countersunk covers only
- 1125 640 1701 — Chain sprocket coverPrevious standard cover · Old collar screws only
- 1128 640 1706 — Chain sprocket coverNew standard cover · Either collar screw type; side-plate change required
- 1122 648 0401 — Wrap-handle sprocket coverPrevious wrap cover · Old collar screws only
- 1122 648 0403 — Wrap-handle sprocket coverNew wrap cover · Either collar screw type; extended lower section
Conditional replacement · MS 440 / MS 460
MS 440 / MS 460: older assembly stand needs the new support
Before mounting machines with collar screws 1138 664 2400 on older stand 5910 890 3100, fit support kit 5910 850 1650.
- Before mounting machines with collar screws 1138 664 2400 on older stand 5910 890 3100, fit support kit 5910 850 1650.
- New stand 5910 890 3101 already includes the support for the new collar screws.
- Retrofitting the support to the older stand requires two washers 9291 021 3870. The source says screws and washers are supplied with the support.
- The mounting screws must not protrude beyond the support surface. This is a service-tool setup condition, not a saw component or a universal modern stand compatibility claim.
- The referenced TI 50/2006 sections 1–2 independently describe the older-stand retrofit; its drawing and summary are retained in the coverage evidence.
- Retained edition: English USA. Introduction is continuous, with no numeric serial cutoff. Historical availability is not current stock or universal regional applicability.
Source: TI 15/2007, p. 1 · TI 15/2007, p. 4 — Section 1.4.1: assembly stand and support installation.
Part numbers (5)
- 1138 664 2400 — Collar screwTriggers stand-support requirement · MS 440 / MS 460 new-screw configuration
- 5910 890 3100 — Assembly standPrevious stand · Requires support retrofit for new collar screws
- 5910 890 3101 — Assembly standNew stand · Support already included
- 5910 850 1650 — Support kitRequired retrofit · Previous stand with new-collar-screw machine
- 9291 021 3870 — WasherTwo required · Support retrofit to previous stand
IPL correction · MS 440 / MS 460
Assembly tool AS: 890 / 007 source-number conflict
TI 15/2007 prints 5910 890 2205 in the mounting-tool heading and drawing, but 5910 007 2205 in the adjacent prose. Neither is silently corrected.
- TI 15/2007 prints 5910 890 2205 in the mounting-tool heading and drawing, but 5910 007 2205 in the adjacent prose. Neither is silently corrected.
- The drawing marks the modified tool with suffix C. The number conflict prevents treating these references as a verified ordering alias or complete machining instruction.
- Both numbers are searchable only to expose this discrepancy; they are not two independently verified fitment approvals.
- Earlier inspected sources also use both forms: TI 46/1995 lists 007, TI 47/2004 lists 890, and TI 14/2006 repeats the heading/prose split. No explicit equivalence or correction was found in those pages.
- Retained edition: English USA. Introduction is continuous, with no numeric serial cutoff. Historical availability is not current stock or universal regional applicability.
Source: TI 15/2007, p. 1 · TI 15/2007, p. 5 — Section 1.4.2 heading, drawing and prose.
Part numbers (2)
- 5910 890 2205 — Assembly tool AS heading/drawing identifierConflicting source reference · Ordering equivalence unresolved; drawing suffix C
- 5910 007 2205 — Assembly tool AS prose identifierConflicting source reference · Ordering equivalence unresolved
Conditional replacement · MS 440 / MS 460
MS 440 / MS 460 service stand: clamping plate and rail replacement
Clamping plate 5910 850 2100 can also be fitted to the previous assembly stand; stand and plate are secured with two M12x20 screws.
Later reviewed guidance: MS 440 / MS 460: older assembly stand needs the new support
- Clamping plate 5910 850 2100 can also be fitted to the previous assembly stand; stand and plate are secured with two M12x20 screws.
- The summary identifies these hex bolts as 9008 319 2930, DIN933-M12x20-8.8, item 7. This fastening is for the workbench clamping plate, not an identification of the support-face socket-head screws.
- The clamping-plate kit includes items 5 to 7: clamping lever 5910 890 1901, circlip 9455 621 0850 and the listed hex bolt. The prose establishes the two-bolt quantity.
- Previous clamping rail 5910 890 2000 is replaced by support kit 5910 850 1650. The support retrofit still requires its separately documented washers and no-protrusion condition.
- These are service-tool relationships shown here beside the existing MS 440/MS 460 stand-support note; they are not saw crankcase parts or a claim that modern stands or all saws fit.
- Retained edition: English USA. Introduction is continuous, with no numeric serial cutoff. Historical availability is not current stock or universal regional applicability.
Source: TI 50/2006, p. 1 · TI 50/2006, p. 2 · TI 50/2006, p. 5 — Sections 1.2, 2 and summary: workbench clamping plate and rail.
Part numbers (6)
- 5910 850 2100 — Clamping plate kitRetrofit to previous stand · Workbench attachment; includes summary items 5–7
- 9008 319 2930 — Hex bolt DIN933-M12x20-8.8Two for clamping plate · Not support-face socket-head screw
- 5910 890 1901 — Clamping leverIncluded item 5 · Clamping-plate kit
- 9455 621 0850 — Circlip DIN471-10x1Included item 6 · Clamping-plate kit
- 5910 890 2000 — Clamping railPrevious version · Replaced by support kit
- 5910 850 1650 — Support kitRail replacement · Separate retrofit conditions apply
IPL correction · MS 440 / MS 460
MS 440 / MS 460 service stand: support-kit fastener references conflict
TI 50/2006 does not unambiguously identify the support-kit mounting screws: page 5 says support 5910 850 1650 includes items 7 and 8, but its support-face drawing shows socket-head screws as item 3.
Later reviewed guidance: MS 440 / MS 460: older assembly stand needs the new support
- TI 50/2006 does not unambiguously identify the support-kit mounting screws: page 5 says support 5910 850 1650 includes items 7 and 8, but its support-face drawing shows socket-head screws as item 3.
- Item 3 is socket-head screw 9045 319 2390; item 7 is hex bolt 9008 319 2930, explicitly used for the separate workbench clamping plate. Do not treat these as aliases or substitute the hex bolt at the support face.
- Page 2 depicts socket-head screws with the support and states that screws and washers are supplied. It requires two washers 9291 021 3870 on the older stand and forbids screws protruding beyond the support.
- The numbered kit-content reference remains unresolved pending an original special-tools parts list or a correcting source. The drawing/prose is not permission to silently amend the table to include item 3.
- This exposes a service-tool source conflict, not a verified kit inventory or an approved purchase/substitution list.
- Retained edition: English USA. Introduction is continuous, with no numeric serial cutoff. Historical availability is not current stock or universal regional applicability.
Source: TI 50/2006, p. 2 · TI 50/2006, p. 5 — Section 1.1 versus summary support-kit included-item references.
Part numbers (4)
- 5910 850 1650 — Support kitConflicting included-item reference · Table says 7/8; support drawing identifies 3
- 9045 319 2390 — Socket-head screwDrawing item 3 · Depicted at support face; kit inclusion unresolved
- 9008 319 2930 — Hex bolt DIN933-M12x20-8.8Table item 7 · Separate clamping-plate fastener; not interchangeable by inference
- 9291 021 3870 — WasherItem 8; two required on older stand · No-protrusion condition remains
Conditional replacement · MS 440
MS 440: crankshaft change from serial 1 54 516 254
Carbonitrided big-end bearing and four recesses in each end face identify the new construction.
1 54 516 254 — MS 440 crankshaft change introduced from this serial; not a universal model-identification range.
- Crankshaft 1128 030 0406 replaces 1128 030 0405 from serial number 1 54 516 254 to improve wear life. This is an MS 440 component changeover, not a whole-model production range or an 044 cutoff.
- The new crankshaft uses a carbonitrided big-end bearing. Four equidistant lubricating recesses are machined in each end face of the connecting-rod big end, improving lubrication of the bearing area. The drawing shows the previous conrod without recesses on the left and new conrod with recesses on the right. It is not an instruction to machine an old connecting rod.
- The previous crankshaft is supplied from the factory only while existing stocks last. No separate bearing or connecting-rod spare number or unrestricted retrofit statement is given. TI 37/2001 is the last-TI bibliographic pointer.
- The named model scope is not extended to other models sharing series 1128 or later IPL sheets. Factory supply statements are historical, not current stock. No physical interchange test was performed.
Source: TI 11/2002, p. 1 — Entire TI 11/2002: prose, conrod comparison, summary and introduction line.
Part numbers (2)
- 1128 030 0405 — CrankshaftPrevious; stocks only · Only the named model and configuration; see conditions
- 1128 030 0406 — Crankshaft with revised big-end bearingNew from printed serial · Only the named model and configuration; see conditions
Service note · MS 440
MS 440 cylinder mounting: longer inserts without a new crankcase number
The production serial boundary is not enough to choose repair screws.
1 62 936 786 — MS 440 production introduction of longer crankcase inserts and M5x25 cylinder screws; repairs still require actual insert and cylinder-rib inspection.
- From machine number 1 62 936 786, both crankcase halves receive longer threaded inserts and the cylinder mounting changes from M5x20 screw 9022 371 1020 to M5x25 screw 9022 371 1050. The increase is the printed 0.197 in (5 mm). The stated purpose is improved crankcase-to-cylinder fastening.
- The CRANKCASE PART NUMBER REMAINS UNCHANGED. The bulletin does not print a crankcase order number, so none is invented here or selected from the later catalog’s multiple rows. The first-page comparison shows short inserts on the left and longer inserts on the right on both halves.
- The previous M5x20 screw remains available for older machines and short-insert crankcases; it is also explicitly required for the long-insert/ribbed-cylinder repair combination described on page 2. The summary says all other parts unchanged; this does not cancel the cylinder rib restriction or authorize M5x25 in every older saw.
- The summary repeats the same machine cutoff and old-part retention. TI39/2003 is the named preceding MS 440 bulletin; the bibliography and copyright footer add no further component fitment. Historical availability is not a current stock check.
- Historical TI30/2004 English USA guidance for MS 440 cylinder mounting only; not MS 460 or a universal M5 screw rule. Inspect both crankcase inserts and cylinder rib configuration; machine number alone does not identify components after repairs. No physical interchange test was performed.
Source: TI 30/2004, p. 1 · TI 30/2004, p. 2 · TI 30/2004, p. 3 — Production change; crankcase; screw identities; complete summary.
Part numbers (2)
- 9022 371 1020 — M5x20 cylinder screwShort inserts; also long-insert case with ribbed cylinder · MS 440 cylinder mounting; insert and rib restrictions apply
- 9022 371 1050 — M5x25 cylinder screwLong inserts AND cylinder without obstructing ribs only · MS 440 cylinder mounting; insert and rib restrictions apply
Service note · MS 440
MS 440 cylinder screws: check insert dimension a and the cylinder ribs
12 ± 0.5 mm and 17 ± 0.5 mm are illustrated insert dimensions, not screw lengths.
- In the crankcase cutaway, dimension a identifies the illustrated threaded-insert extent. The source pairs a = 0.472 ± 0.020 in (12 ± 0.5 mm) with M5x20 / 9022 371 1020, and a = 0.669 ± 0.020 in (17 ± 0.5 mm) with M5x25 / 9022 371 1050. Preserve the printed metric and inch pairs; these are not 12 mm or 17 mm screw lengths, and no measurement method beyond the drawing is specified.
- The new M5x25 screw may be used ONLY WITH THE LONGER INSERTS. A 17 mm insert is necessary but not sufficient: the cylinder must also lack the obstructing ribs shown as (a) in the separate cylinder figure. Its labels (a)/(b) are configuration identifiers, not the crankcase drawing’s dimension a.
- The screw/crankcase table uses “only” permitted combinations, but the adjacent cylinder repair paragraph explicitly requires M5x20 when a NEW long-insert crankcase is combined with a RIBBED cylinder. Retain this stated exception rather than treating the table alone as a universal prohibition of short screws in long inserts.
- Tightening torque remains the printed 102 lbf in (11.5 Nm). These are inch-pounds, NOT foot-pounds. No revised torque, sealant, threadlocker, tightening order or permission to deepen an insert is supplied. All four cylinder screws must be the same length under the cylinder instruction.
- Historical TI30/2004 English USA guidance for MS 440 cylinder mounting only; not MS 460 or a universal M5 screw rule. Inspect both crankcase inserts and cylinder rib configuration; machine number alone does not identify components after repairs. No physical interchange test was performed.
Source: TI 30/2004, p. 2 — Screws; repair-note dimensions and tightening torque; cylinder exception.
Part numbers (2)
- 9022 371 1020 — M5x20 cylinder screwShort inserts; also long-insert case with ribbed cylinder · MS 440 cylinder mounting; insert and rib restrictions apply
- 9022 371 1050 — M5x25 cylinder screwLong inserts AND cylinder without obstructing ribs only · MS 440 cylinder mounting; insert and rib restrictions apply
Service note · MS 440
MS 440 ribbed cylinder: keep four M5x20 screws even on a new crankcase
Long inserts do not remove the cylinder-rib clearance restriction.
- The cylinder figure marks the ribbed configuration (a) and the configuration without those ribs (b). M5x25 CANNOT be used on the ribbed cylinder (a). It can be used on cylinder (b) only together with the long crankcase inserts required by the adjacent screw note; absence of ribs alone does not permit longer screws in short inserts.
- When a new crankcase WITH LONGER INSERTS is combined during repair with a cylinder WITH RIBS (a), use the SHORTER M5x20 screws 9022 371 1020. This is an explicit repair exception, not an inferred substitution and not permission to grind away ribs or alter screw length.
- To ensure uniform thermal expansion, the cylinder MUST ALWAYS be secured with FOUR SCREWS OF THE SAME LENGTH. Do not mix M5x20 and M5x25 around one cylinder. The source supplies no ribbed/unribbed cylinder order numbers, so this is a physical-configuration condition, not an assignment to an unverified catalog cylinder number.
- Historical TI30/2004 English USA guidance for MS 440 cylinder mounting only; not MS 460 or a universal M5 screw rule. Inspect both crankcase inserts and cylinder rib configuration; machine number alone does not identify components after repairs. No physical interchange test was performed.
Source: TI 30/2004, p. 2 — Cylinder figure and full repair exception; uniform thermal expansion.
Part numbers (2)
- 9022 371 1020 — M5x20 cylinder screwShort inserts; also long-insert case with ribbed cylinder · MS 440 cylinder mounting; insert and rib restrictions apply
- 9022 371 1050 — M5x25 cylinder screwLong inserts AND cylinder without obstructing ribs only · MS 440 cylinder mounting; insert and rib restrictions apply
Service note · MS 440 / MS 460
MS 440 / MS 460: collar shank and cover-hole dimensions
The longer collar shank and countersunk cover holes are separate dimensional changes.
- Old collar screw 0000 953 6605 has a 0.14-inch (3.5 mm) shank; new 1138 664 2400 has a 0.28-inch (7 mm) shank and stepped thread entry for easier bar-nut mounting. These are shank lengths, not overall screw lengths.
- The TWO modified cover holes are described with a countersunk diameter of 0.50 inch (12.5 mm) and depth of 0.12 inch (3 mm), retaining the source's rounded inch/metric pairs. No countersink angle for the COVER is given here.
- Old covers without countersunk holes are forbidden with new collar screws. New countersunk covers accept old OR new screws. Wrap-around machines additionally require the outward-projecting extended lower cover section; a countersink alone does not supply that protection.
- The source describes the changed cover geometry, not a complete machining procedure for an old cover. Its later 90-degree illustration concerns the MOUNTING TOOL, not this cover. The lug-free side-plate and matching screw requirement remains in the existing side-plate note.
- Retained 2007 source guidance, not present-day stock availability. No numeric serial cutoff is supplied. No physical interchange test was performed.
Source: TI 15/2007, p. 1 · TI 15/2007, p. 2 · TI 15/2007, p. 3 · TI 15/2007, p. 4 · TI 15/2007, p. 5 — MS 440 / MS 460: collar shank and cover-hole dimensions.
Part numbers (2)
- 0000 953 6605 — Previous collar screw3.5 mm shank · MS 440 / MS 460; source restrictions apply
- 1138 664 2400 — New collar screw7 mm shank; countersunk cover required · MS 440 / MS 460; source restrictions apply
Service note · MS 440 / MS 460
MS 440 / MS 460: mounting-tool countersinks and suffix C
The drawing shows two 90-degree countersinks, while the ordering-number conflict remains unresolved.
- Section 1.4.2 says the clutch-side mounting-tool flange must be adapted to the tapered contour of the new collar screws. An existing tool lacking the hole countersinks may be modified as the drawing shows.
- Figure 901TI063 KN shows TWO 90-degree countersinks and identifies the tool as 5910 890 2205 C. The 90-degree values are countersink angles, NOT drilling angles, cover-hole dimensions or torque settings. No countersink diameter or depth is given for the tool in this figure.
- The heading and drawing print 5910 890 2205; adjacent prose TWICE prints 5910 007 2205. This is a retained source-number conflict, not a verified ordering alias. The text states only modified tools are then supplied and identified by suffix C.
- Do not borrow the COVER dimensions of 12.5 mm diameter and 3 mm depth from section 1.2 as tool machining specifications. The drawing and unresolved identity do not establish a complete manufacturing instruction or interchange approval.
- Retained 2007 source guidance, not present-day stock availability. No numeric serial cutoff is supplied. No physical interchange test was performed.
Source: TI 15/2007, p. 2 · TI 15/2007, p. 5 — MS 440 / MS 460: mounting-tool countersinks and suffix C.
Part numbers (3)
- 5910 890 2205 — Clutch-side mounting toolHeading/drawing identifier; suffix C · MS 440 / MS 460; source restrictions apply
- 5910 007 2205 — Conflicting tool identifierProse only; identity unresolved · MS 440 / MS 460; source restrictions apply
- 1138 664 2400 — Collar screwTapered contour drives tool adaptation · MS 440 / MS 460; source restrictions apply
Service note · MS 440 / MS 460
MS 440 / MS 460: 2007 supply remarks are configuration-specific
The summary preserves old-model stock separately from new-part retrofit permission.
- Page 8 has 14 rows, with continuous introduction and NO numeric serial cutoff. Remark 1 means the old part remains for older machines; remark 2 means the old part is no longer available from the factory; remark 3 permits the new part as a spare for older machines; remark 4 retains the old part for OTHER models.
- Rows 1/2 (MS 440/MS 460 crankcases), row 4 (standard cover), and rows 3/12 (collar screw/old elbow) retain old versions for older machines under remark 1. Rows 3/12 additionally carry remark 4. The old bearing in row 14 carries remark 4 ONLY; section 4 separately permits the new bearing in older MS 460 machines and leaves the flywheel bearing unchanged.
- Rows 5–9 and 11 carry remarks 2 AND 3: spike/catcher cover, wrap cover, wrap spike/catcher cover, rescue cover, standard wrap handle, and heated wrap handle. Row 10 rescue/tool-holder handle carries remark 3 without specifying an old version. Row 13 new elbow has no separate remark; its restrictions are in section 3.
- Crankcase rows include collar-screw item 3. Wrap spike/catcher and rescue cover rows 7/8 include wrap-cover item 6. Standard and tool-holder handle rows 9/10 expressly include elbow item 13; heated handle inclusion follows the page 6 service text. The blank new cell for OLD elbow row 12 is not permission to omit the matching elbow; the new elbow appears separately as row 13.
- Only cover rows 5/7 explicitly name 046 alongside MS 460; their separate 046 notes do not broaden the crankcase, handle or bearing scope. Footer is 2007 Technical Documentation D1/MTK-bl; retained edition is English USA. Historical supply remarks do not establish current inventory or universal regional fitment.
- Retained 2007 source guidance, not present-day stock availability. No numeric serial cutoff is supplied. No physical interchange test was performed.
Source: TI 15/2007, p. 1 · TI 15/2007, p. 2 · TI 15/2007, p. 3 · TI 15/2007, p. 4 · TI 15/2007, p. 5 · TI 15/2007, p. 6 · TI 15/2007, p. 7 · TI 15/2007, p. 8 — MS 440 / MS 460: 2007 supply remarks are configuration-specific.
No additional parts-table entry added.
Service note · MS 361 / MS 362 / MS 440 / MS 441 / MS 460 / MS 650 / MS 660 / MS 880
MS 361, MS 362, MS 440, MS 441, MS 460, MS 650, MS 660, MS 880: magnesium stud adhesive changes to Loctite 270
Metric-thread crankcase studs: Loctite 243 (USA 242) → Loctite 270; not polymer housings.
- Exact listed magnesium-crankcase models: MS 361, MS 362, MS 440, MS 441, MS 460, MS 650, MS 660, MS 880. Their metric-thread studs change from Loctite 243 (USA: Loctite 242) to Loctite 270. No stud part number, serial changeover, cure time or torque is specified here.
- Before stud reassembly, clean BOTH threads: insert the tap into the internal thread BY HAND, then blow out the threaded hole; brush off the external stud thread. Coat the cleaned stud with Loctite 270. This thread-cleaning instruction is not permission to enlarge the polymer repair-stud hole.
- Loctite is NOT used for studs in polymer engine housings. The magnesium adhesive change does not override the separate polymer repair restrictions or give these models permission to use the oversized polymer repair studs.
- The repeated words engine housings at the end of page3 are present in the original scan; they add no second instruction and are not silently corrected in the retained source.
- Historical English TI29/2011. Only the printed model and material scope is admitted; no unlisted variants or predecessor models are inferred. No physical interchange test was performed.
Source: TI 29/2011, p. 3 — MS 361, MS 362, MS 440, MS 441, MS 460, MS 650, MS 660, MS 880: magnesium stud adhesive changes to Loctite 270.
No additional parts-table entry added.
Wrong number or missing part for the MS 440? Report a correction →