← 044/046 · MS 440/460/461

Stihl 1128 · Section B · 2 of 16 · 24 parts

Cylinder

Fits MS 460.

Parts diagrams →

Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
110111213141516171819220213456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (24)

PosPart numberDescriptionQty
1 1128 020 1221 Cylinder with piston Ø 52 mm — 76.5 cc 1
1 1128 020 1217 NLA Cylinder with piston Ø 52 mm — 76.5 cc 1
2 1128 030 2009 Piston Ø 52 mm — 76.5 cc 1
3 1122 034 3000 Piston ring Ø 52x1.2 mm — 76.5 cc 2
4 1128 034 1501 Piston pin 12x8x35 1
5 9463 650 1200 Snap ring 12x1 2
6 9512 003 3061 Needle cage 12x15x15 1
7 1128 029 2304 Cylinder gasket 0.3 mm 1
8 1128 029 2306 NLA Cylinder gasket 0.8 mm 1
9 9022 341 1370 Spline screw IS-M6x30 4
10 1128 020 9400 Decompression valve 1
11 1122 084 1405 Cover 1
12 1128 141 3200 Cooling plate 1
13 1125 149 0601 Muffler gasket 1
14 1128 141 2203 Manifold Fitment / change note → → replaced by 1128 141 2204 TI 46/2008 1
15 1128 141 2204 Manifold Fitment / change note → 1
16 9771 021 2578 Hose clip Ø 34x5 1
17 1110 400 7005 Spark plug Bosch WSR 6 F 1
17 0000 400 7000 Spark plug NGK BPMR7A 1
18 1128 084 1400 Cover 1
19 1128 405 1000 Spark plug boot 1
20 0000 998 0604 Torsion spring 1
21 1122 025 2200 Plug 1
Not numbered on the diagram — assemblies, kits and options
— 1128 007 1052 Set of gaskets option 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Conditional replacement · MS 460

MS 460: two earlier manifolds replaced by 1128 141 2203

The manifold revision improves resistance to temperature changes; its introduction is in progress, without a numeric cutoff.

  • 1128 141 2200 and 1128 141 2202 are replaced by 1128 141 2203 in the described MS 460 change.
  • Do not copy the crankshaft serial 1 54 517 175 onto the manifold: the summary explicitly gives separate introduction conditions.
  • Earlier manifolds remain available only while factory stocks last in the source. No blanket 046 retrofit or all-market introduction date is established.
  • Drawing 175TI001 KN compares previous manifold 1128 141 2200 at top with new 1128 141 2203 at bottom. Its arrows mark the illustrated profile comparison, but supply no dimensions, material specification or temperature rating. Previous manifold 1128 141 2202 is independently named in prose and summary item 3, not separately identified in that drawing.
  • Summary items 2 and 3 each map an earlier manifold to 1128 141 2203 and each carry the factory-stocks-last remark. The manifold introduction remains in progress. Retained edition is english / USA.

Source: TI 16/2002, p. 1 · TI 16/2002, p. 2 — Complete sections 1–3: crankshaft and manifold revisions, both comparison diagrams, all three summary rows and separate introduction conditions.

Part numbers (3)
  • 1128 141 2200 — ManifoldPrevious version · MS 460 described configuration
  • 1128 141 2202 — ManifoldPrevious version · MS 460 described configuration
  • 1128 141 2203 — Temperature-resistant manifold revisionNew version · MS 460; introduction in progress

Service note · MS 440 / MS 460

MS 440 / MS 460: cold-resistant manifold and molded identification

The new manifold serves heated versions; the old one remains for unheated versions.

  • Cover identifies MS 440/MS 460, series 1128. Previous manifold 1128 141 2203 is replaced by 1128 141 2204 FOR MACHINES WITH CARBURETOR AND HANDLE HEATING. New manifold is described as extremely resistant to low temperatures; no temperature rating is printed.
  • Figure 175TI016 points to the molded identification: old 1128 141 2203 bears 1128/03 OR 1128; new 1128 141 2204 bears 1128/04. These markings identify the manifold revision, not a saw serial number.
  • Old manifold 1128 141 2203 REMAINS AVAILABLE for versions WITHOUT carburetor and handle heating. For service, new 1128 141 2204 may also be installed in OTHER VERSIONS where extreme low-temperature resistance is required. This qualified permission is not universal old-part obsolescence or evidence for unnamed044/046/MS 461.
  • Summary repeats the replacement with old-part other-model availability and CONTINUOUS introduction. No numeric serial changeover or installation procedure is supplied.
  • Historical English 2008 source, not present-day stock or approval for unlisted variants. No numeric serial cutoff is supplied. No physical interchange test was performed.

Source: TI 46/2008, p. 1 · TI 46/2008, p. 2 — MS 440 / MS 460: cold-resistant manifold and molded identification.

Part numbers (2)
  • 1128 141 2203 — Previous manifold1128/03 or1128 marking; unheated supply retained · MS 440 / MS 460; source restrictions apply
  • 1128 141 2204 — Cold-resistant manifold1128/04 marking; heated/qualified service use · MS 440 / MS 460; source restrictions apply

Wrong number or missing part for the MS 460? Report a correction →