Stihl 1128 · Section A · 1 of 16 · 38 parts
Crankcase, Crankshaft
Fits MS 460.
Historical fitment & changes (12) — includes parts and conditions not shown on this drawing.
Parts (38)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1128 020 2137 | Crankcase Fitment / change note → | 1 |
| 2 | 1128 020 2123 | Crankcase Fitment / change note → → replaced by 1128 020 2137 TI 15/2007 | 1 |
| 3 | 0000 988 5211 | Connector | 1 |
| 4 | 9371 470 2610 | Cylindrical pin 5x18 | 2 |
| 5 | 0000 974 1200 | Notched pin 2.6x8 | 1 |
| 6 | 1128 640 9100 | Valve | 1 |
| 7 | 9503 003 0346 | Grooved ball bearing 6202 | 1 |
| 8 | 9523 003 4278 | Grooved ball bearing 15x35x13 Fitment / change note → | 1 |
| 9 | 1138 664 2400 | Collar screw Fitment / change note → | 2 |
| 10 | 0000 953 6605 | Collar screw M8 Fitment / change note → | 2 |
| 11 | 9022 371 1020 | Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 | 5 |
| 12 | 1120 162 5200 | Pin | 1 |
| 13 | 1121 162 5205 | Pin | 1 |
| 14 | 1128 162 5200 | Pin | 1 |
| 15 | 1121 162 5200 | Pin | 1 |
| 16 | 1128 084 8302 | Reflector foil | 1 |
| 17 | 1128 647 9405 | Hose | 1 |
| 18 | 1117 640 3800 | Pickup body | 1 |
| 19 | 9640 003 1355 | Oil seal 13.5x20x4 | 1 |
| 20 | 9640 003 1600 | Oil seal 15x29.6x4 | 1 |
| 21 | 1128 029 0502 | Gasket | 1 |
| 22 | 1128 030 0402 | Crankshaft Fitment / change note → | 1 |
| 23 | 1120 036 8500 | Woodruff key 2x3.7 | 1 |
| 24 | 9455 621 1520 | Circlip 15x1 | 1 |
| 25 | 1124 791 2800 | Stop buffer | 1 |
| 26 | 1125 007 1021 | Spur gear / chain adjusting screw kit | 1 |
| 27 | 9646 945 0490 | O-ring 7x1.5 | 1 |
| 28 | 1125 640 1900 | Tensioner slide | 1 |
| 29 | 1122 664 2200 | Cover plate | 1 |
| 30 | 9041 216 0630 | Pan head screw M4x8 | 2 |
| 31 | 1125 664 1400 | Thrust pad | 1 |
| 32 | 1122 664 4500 | Support | 1 |
| 33 | 1128 664 1001 | Inner side plate 0.9 mm → replaced by 1128 664 1002 TI 12/1994 | 1 |
| 34 | 1128 664 1002 NLA | Inner side plate → replaced by 1128 664 1001, 1128 664 1001 TI 10/2007 option | 1 |
| 35 | 1133 791 5900 | Stop buffer | 1 |
| 36 | 0000 350 0525 | Filler cap Fitment / change note → | 1 |
| 37 | 9645 948 7734 | O-ring 25x3.5 | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 1128 007 1052 | Set of gaskets option | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Conditional replacement · MS 460
MS 460: crankshaft change from 1 54 517 175
TI 16/2002 replaces crankshaft 1128 030 0404 with 1128 030 0402 at the stated MS 460 changeover.
1 54 517 175 — MS 460 crankshaft introduction in the retained USA edition, not a manifold cutoff or model-identification range.
- From serial number 1 54 517 175: new crankshaft 1128 030 0402 has an improved big-end bearing and four lubricating recesses in each big-end face.
- This numeric cutoff is for the crankshaft only. The manifold change in the same bulletin is separately marked in progress.
- The previous crankshaft is supplied only while factory stocks last in this historical bulletin. This is not current stock information or proof of interchange with every older 046.
- Source edition is marked english / USA; do not silently generalize its introduction cutoff to every regional variant.
- Drawing 176TI009 KN shows the previous conrod without recesses at left and revised conrod with lubricating recesses at right. Four recesses are machined in each end face of the big end, not four total per conrod. The stated purpose is improved bearing lubrication and durability; no quantified durability gain or instructions to machine an older conrod are supplied.
- Summary item 1 repeats the crankshaft-only introduction from serial 1 54 517 175 and the old-part factory-stocks-last remark. No separate bearing part number, recess dimensions or stand-alone bearing conversion is specified.
Source: TI 16/2002, p. 1 · TI 16/2002, p. 2 — Complete sections 1–3: crankshaft and manifold revisions, both comparison diagrams, all three summary rows and separate introduction conditions.
Part numbers (2)
- 1128 030 0404 — CrankshaftPrevious version · MS 460 before the described change
- 1128 030 0402 — Crankshaft with improved big-end lubricationNew version · MS 460 from stated crankshaft cutoff
Conditional replacement · 046 / MS 460
046 repair / MS 460 transition: crankcase and matching oil cap
TI 05/2001 allows the revised crankcase with matching cap for 046 repairs, not a cap-only retrofit.
- Crankcase 1128 020 2118 → 1128 020 2123. The new oil filler opening requires cap 0000 350 0525.
- The source supplies the new cap with the replacement case for about three years so it can repair 046 saws. This historical packaging statement does not establish current contents.
- Do not use the cap alone as a retrofit to an old crankcase opening. Introduction is in progress, without a numeric cutoff.
- Retained edition is english / USA; no universal cross-variant replacement is inferred.
- The tool-free cap has a grip for operation and is the same type for fuel and oil. To open, raise the grip upright, turn about one-quarter turn counterclockwise, and remove. To close, fit with grip upright and the cap/opening marks aligned, turn about one-quarter turn clockwise to the stop, then fold the grip down. The closing check is that the grip’s lug engages the recess; merely folding the grip down is not the stated check. Drawings 176TI001–004 KN show this sequence for the matching opening.
- Summary item 6 includes item 7, the new oil filler cap 0000 350 0525. The previous-cap cell is printed as a dash; no previous oil-cap part number is assigned from this row. Remark 1 marks the previous crankcase no longer available from the factory at the time of this TI, not current stock information.
Source: TI 5/2001, p. 1 · TI 5/2001, p. 2 · TI 5/2001, p. 3 · TI 5/2001, p. 4 — Complete sections 1–7: 046/MS460 naming, cap operation, tank and crankcase matching assemblies, vent construction/function, clutch and all summary rows.
Part numbers (3)
- 1128 020 2118 — CrankcasePrevious version · 046 previous oil filler opening
- 1128 020 2123 — CrankcaseNew matching assembly · MS 460 transition; 046 repair with matching cap
- 0000 350 0525 — Oil filler capRequired matching cap · New crankcase opening only
Conditional replacement · MS 460
MS 460: collar screws determine cover compatibility
Old covers without countersunk holes must not be used with new collar screws 1138 664 2400. New countersunk covers accept either collar screw type.
- Old covers without countersunk holes must not be used with new collar screws 1138 664 2400. New countersunk covers accept either collar screw type.
- Crankcase 1128 020 2123 with old screws remains a historical service option for older covers; 1128 020 2137 includes new screws.
- Wrap-around handlebars require the cover with an extended outward-projecting lower section; a countersink alone does not establish wrap-handle suitability.
- When fitting a new cover, replace the lugged side plate with the lug-free version and its specified screw; see the linked sheet note.
- This is a configuration rule, not permission to machine an old cover or infer an unrestricted 044/046 crankcase swap.
- Retained edition: English USA. Introduction is continuous, with no numeric serial cutoff. Historical availability is not current stock or universal regional applicability.
Source: TI 15/2007, p. 1 · TI 15/2007, p. 2 · TI 15/2007, p. 3 · TI 15/2007, p. 4 · TI 15/2007, p. 8 — Sections 1.1–1.3 and summary: model-specific cases/covers, compatibility matrix.
Part numbers (12)
- 1128 020 2123 — CrankcasePrevious version · MS 460; old collar screws
- 1128 020 2137 — CrankcaseRevised version · MS 460; new collar screws
- 0000 953 6605 — Collar screwPrevious version · Old or countersunk covers
- 1138 664 2400 — Collar screwNew version · Countersunk covers only
- 1125 640 1701 — Chain sprocket coverPrevious standard cover · Old collar screws only
- 1128 640 1706 — Chain sprocket coverNew standard cover · Either collar screw type; side-plate change required
- 1122 648 0401 — Wrap-handle sprocket coverPrevious wrap cover · Old collar screws only
- 1122 648 0403 — Wrap-handle sprocket coverNew wrap cover · Either collar screw type; extended lower section
- 1128 640 1701 — Cover with spike and catcherPrevious assembly · Old collar screws only
- 1128 640 1707 — Cover with spike and catcherNew assembly · Either collar screw type
- 1128 640 1700 — Wrap cover with spike and catcherPrevious assembly · Old collar screws only
- 1128 640 1708 — Wrap cover with spike and catcherNew assembly · Either collar screw type; includes 1122 648 0403
Conditional replacement · MS 460
MS 460: revised clutch-side bearing, flywheel side unchanged
Clutch-side bearing 9523 003 4278 replaces 9523 003 4266; the new bearing may also be used in older machines within the stated MS 460 scope.
- Clutch-side bearing 9523 003 4278 replaces 9523 003 4266; the new bearing may also be used in older machines within the stated MS 460 scope.
- The flywheel-side bearing remains unchanged. Do not apply this replacement to both crankshaft bearings.
- Section 4 is explicitly MS 460 only; the broader bulletin heading does not make this an MS 440 bearing change. No universal 046 retrofit is inferred.
- Retained edition: English USA. Introduction is continuous, with no numeric serial cutoff. Historical availability is not current stock or universal regional applicability.
Source: TI 15/2007, p. 1 · TI 15/2007, p. 7 · TI 15/2007, p. 8 — Section 4 and summary bearing row.
Part numbers (2)
- 9523 003 4266 — Grooved ball bearingPrevious version · MS 460 clutch side
- 9523 003 4278 — Grooved ball bearingRevised version · MS 460 clutch side; older MS 460 permitted
Conditional replacement · MS 440 / MS 460
MS 440 / MS 460: older assembly stand needs the new support
Before mounting machines with collar screws 1138 664 2400 on older stand 5910 890 3100, fit support kit 5910 850 1650.
- Before mounting machines with collar screws 1138 664 2400 on older stand 5910 890 3100, fit support kit 5910 850 1650.
- New stand 5910 890 3101 already includes the support for the new collar screws.
- Retrofitting the support to the older stand requires two washers 9291 021 3870. The source says screws and washers are supplied with the support.
- The mounting screws must not protrude beyond the support surface. This is a service-tool setup condition, not a saw component or a universal modern stand compatibility claim.
- The referenced TI 50/2006 sections 1–2 independently describe the older-stand retrofit; its drawing and summary are retained in the coverage evidence.
- Retained edition: English USA. Introduction is continuous, with no numeric serial cutoff. Historical availability is not current stock or universal regional applicability.
Source: TI 15/2007, p. 1 · TI 15/2007, p. 4 — Section 1.4.1: assembly stand and support installation.
Part numbers (5)
- 1138 664 2400 — Collar screwTriggers stand-support requirement · MS 440 / MS 460 new-screw configuration
- 5910 890 3100 — Assembly standPrevious stand · Requires support retrofit for new collar screws
- 5910 890 3101 — Assembly standNew stand · Support already included
- 5910 850 1650 — Support kitRequired retrofit · Previous stand with new-collar-screw machine
- 9291 021 3870 — WasherTwo required · Support retrofit to previous stand
IPL correction · MS 440 / MS 460
Assembly tool AS: 890 / 007 source-number conflict
TI 15/2007 prints 5910 890 2205 in the mounting-tool heading and drawing, but 5910 007 2205 in the adjacent prose. Neither is silently corrected.
- TI 15/2007 prints 5910 890 2205 in the mounting-tool heading and drawing, but 5910 007 2205 in the adjacent prose. Neither is silently corrected.
- The drawing marks the modified tool with suffix C. The number conflict prevents treating these references as a verified ordering alias or complete machining instruction.
- Both numbers are searchable only to expose this discrepancy; they are not two independently verified fitment approvals.
- Earlier inspected sources also use both forms: TI 46/1995 lists 007, TI 47/2004 lists 890, and TI 14/2006 repeats the heading/prose split. No explicit equivalence or correction was found in those pages.
- Retained edition: English USA. Introduction is continuous, with no numeric serial cutoff. Historical availability is not current stock or universal regional applicability.
Source: TI 15/2007, p. 1 · TI 15/2007, p. 5 — Section 1.4.2 heading, drawing and prose.
Part numbers (2)
- 5910 890 2205 — Assembly tool AS heading/drawing identifierConflicting source reference · Ordering equivalence unresolved; drawing suffix C
- 5910 007 2205 — Assembly tool AS prose identifierConflicting source reference · Ordering equivalence unresolved
Conditional replacement · MS 440 / MS 460
MS 440 / MS 460 service stand: clamping plate and rail replacement
Clamping plate 5910 850 2100 can also be fitted to the previous assembly stand; stand and plate are secured with two M12x20 screws.
Later reviewed guidance: MS 440 / MS 460: older assembly stand needs the new support
- Clamping plate 5910 850 2100 can also be fitted to the previous assembly stand; stand and plate are secured with two M12x20 screws.
- The summary identifies these hex bolts as 9008 319 2930, DIN933-M12x20-8.8, item 7. This fastening is for the workbench clamping plate, not an identification of the support-face socket-head screws.
- The clamping-plate kit includes items 5 to 7: clamping lever 5910 890 1901, circlip 9455 621 0850 and the listed hex bolt. The prose establishes the two-bolt quantity.
- Previous clamping rail 5910 890 2000 is replaced by support kit 5910 850 1650. The support retrofit still requires its separately documented washers and no-protrusion condition.
- These are service-tool relationships shown here beside the existing MS 440/MS 460 stand-support note; they are not saw crankcase parts or a claim that modern stands or all saws fit.
- Retained edition: English USA. Introduction is continuous, with no numeric serial cutoff. Historical availability is not current stock or universal regional applicability.
Source: TI 50/2006, p. 1 · TI 50/2006, p. 2 · TI 50/2006, p. 5 — Sections 1.2, 2 and summary: workbench clamping plate and rail.
Part numbers (6)
- 5910 850 2100 — Clamping plate kitRetrofit to previous stand · Workbench attachment; includes summary items 5–7
- 9008 319 2930 — Hex bolt DIN933-M12x20-8.8Two for clamping plate · Not support-face socket-head screw
- 5910 890 1901 — Clamping leverIncluded item 5 · Clamping-plate kit
- 9455 621 0850 — Circlip DIN471-10x1Included item 6 · Clamping-plate kit
- 5910 890 2000 — Clamping railPrevious version · Replaced by support kit
- 5910 850 1650 — Support kitRail replacement · Separate retrofit conditions apply
IPL correction · MS 440 / MS 460
MS 440 / MS 460 service stand: support-kit fastener references conflict
TI 50/2006 does not unambiguously identify the support-kit mounting screws: page 5 says support 5910 850 1650 includes items 7 and 8, but its support-face drawing shows socket-head screws as item 3.
Later reviewed guidance: MS 440 / MS 460: older assembly stand needs the new support
- TI 50/2006 does not unambiguously identify the support-kit mounting screws: page 5 says support 5910 850 1650 includes items 7 and 8, but its support-face drawing shows socket-head screws as item 3.
- Item 3 is socket-head screw 9045 319 2390; item 7 is hex bolt 9008 319 2930, explicitly used for the separate workbench clamping plate. Do not treat these as aliases or substitute the hex bolt at the support face.
- Page 2 depicts socket-head screws with the support and states that screws and washers are supplied. It requires two washers 9291 021 3870 on the older stand and forbids screws protruding beyond the support.
- The numbered kit-content reference remains unresolved pending an original special-tools parts list or a correcting source. The drawing/prose is not permission to silently amend the table to include item 3.
- This exposes a service-tool source conflict, not a verified kit inventory or an approved purchase/substitution list.
- Retained edition: English USA. Introduction is continuous, with no numeric serial cutoff. Historical availability is not current stock or universal regional applicability.
Source: TI 50/2006, p. 2 · TI 50/2006, p. 5 — Section 1.1 versus summary support-kit included-item references.
Part numbers (4)
- 5910 850 1650 — Support kitConflicting included-item reference · Table says 7/8; support drawing identifies 3
- 9045 319 2390 — Socket-head screwDrawing item 3 · Depicted at support face; kit inclusion unresolved
- 9008 319 2930 — Hex bolt DIN933-M12x20-8.8Table item 7 · Separate clamping-plate fastener; not interchangeable by inference
- 9291 021 3870 — WasherItem 8; two required on older stand · No-protrusion condition remains
Service note · MS 440 / MS 460
MS 440 / MS 460: collar shank and cover-hole dimensions
The longer collar shank and countersunk cover holes are separate dimensional changes.
- Old collar screw 0000 953 6605 has a 0.14-inch (3.5 mm) shank; new 1138 664 2400 has a 0.28-inch (7 mm) shank and stepped thread entry for easier bar-nut mounting. These are shank lengths, not overall screw lengths.
- The TWO modified cover holes are described with a countersunk diameter of 0.50 inch (12.5 mm) and depth of 0.12 inch (3 mm), retaining the source's rounded inch/metric pairs. No countersink angle for the COVER is given here.
- Old covers without countersunk holes are forbidden with new collar screws. New countersunk covers accept old OR new screws. Wrap-around machines additionally require the outward-projecting extended lower cover section; a countersink alone does not supply that protection.
- The source describes the changed cover geometry, not a complete machining procedure for an old cover. Its later 90-degree illustration concerns the MOUNTING TOOL, not this cover. The lug-free side-plate and matching screw requirement remains in the existing side-plate note.
- Retained 2007 source guidance, not present-day stock availability. No numeric serial cutoff is supplied. No physical interchange test was performed.
Source: TI 15/2007, p. 1 · TI 15/2007, p. 2 · TI 15/2007, p. 3 · TI 15/2007, p. 4 · TI 15/2007, p. 5 — MS 440 / MS 460: collar shank and cover-hole dimensions.
Part numbers (2)
- 0000 953 6605 — Previous collar screw3.5 mm shank · MS 440 / MS 460; source restrictions apply
- 1138 664 2400 — New collar screw7 mm shank; countersunk cover required · MS 440 / MS 460; source restrictions apply
Service note · MS 440 / MS 460
MS 440 / MS 460: mounting-tool countersinks and suffix C
The drawing shows two 90-degree countersinks, while the ordering-number conflict remains unresolved.
- Section 1.4.2 says the clutch-side mounting-tool flange must be adapted to the tapered contour of the new collar screws. An existing tool lacking the hole countersinks may be modified as the drawing shows.
- Figure 901TI063 KN shows TWO 90-degree countersinks and identifies the tool as 5910 890 2205 C. The 90-degree values are countersink angles, NOT drilling angles, cover-hole dimensions or torque settings. No countersink diameter or depth is given for the tool in this figure.
- The heading and drawing print 5910 890 2205; adjacent prose TWICE prints 5910 007 2205. This is a retained source-number conflict, not a verified ordering alias. The text states only modified tools are then supplied and identified by suffix C.
- Do not borrow the COVER dimensions of 12.5 mm diameter and 3 mm depth from section 1.2 as tool machining specifications. The drawing and unresolved identity do not establish a complete manufacturing instruction or interchange approval.
- Retained 2007 source guidance, not present-day stock availability. No numeric serial cutoff is supplied. No physical interchange test was performed.
Source: TI 15/2007, p. 2 · TI 15/2007, p. 5 — MS 440 / MS 460: mounting-tool countersinks and suffix C.
Part numbers (3)
- 5910 890 2205 — Clutch-side mounting toolHeading/drawing identifier; suffix C · MS 440 / MS 460; source restrictions apply
- 5910 007 2205 — Conflicting tool identifierProse only; identity unresolved · MS 440 / MS 460; source restrictions apply
- 1138 664 2400 — Collar screwTapered contour drives tool adaptation · MS 440 / MS 460; source restrictions apply
Service note · MS 440 / MS 460
MS 440 / MS 460: 2007 supply remarks are configuration-specific
The summary preserves old-model stock separately from new-part retrofit permission.
- Page 8 has 14 rows, with continuous introduction and NO numeric serial cutoff. Remark 1 means the old part remains for older machines; remark 2 means the old part is no longer available from the factory; remark 3 permits the new part as a spare for older machines; remark 4 retains the old part for OTHER models.
- Rows 1/2 (MS 440/MS 460 crankcases), row 4 (standard cover), and rows 3/12 (collar screw/old elbow) retain old versions for older machines under remark 1. Rows 3/12 additionally carry remark 4. The old bearing in row 14 carries remark 4 ONLY; section 4 separately permits the new bearing in older MS 460 machines and leaves the flywheel bearing unchanged.
- Rows 5–9 and 11 carry remarks 2 AND 3: spike/catcher cover, wrap cover, wrap spike/catcher cover, rescue cover, standard wrap handle, and heated wrap handle. Row 10 rescue/tool-holder handle carries remark 3 without specifying an old version. Row 13 new elbow has no separate remark; its restrictions are in section 3.
- Crankcase rows include collar-screw item 3. Wrap spike/catcher and rescue cover rows 7/8 include wrap-cover item 6. Standard and tool-holder handle rows 9/10 expressly include elbow item 13; heated handle inclusion follows the page 6 service text. The blank new cell for OLD elbow row 12 is not permission to omit the matching elbow; the new elbow appears separately as row 13.
- Only cover rows 5/7 explicitly name 046 alongside MS 460; their separate 046 notes do not broaden the crankcase, handle or bearing scope. Footer is 2007 Technical Documentation D1/MTK-bl; retained edition is English USA. Historical supply remarks do not establish current inventory or universal regional fitment.
- Retained 2007 source guidance, not present-day stock availability. No numeric serial cutoff is supplied. No physical interchange test was performed.
Source: TI 15/2007, p. 1 · TI 15/2007, p. 2 · TI 15/2007, p. 3 · TI 15/2007, p. 4 · TI 15/2007, p. 5 · TI 15/2007, p. 6 · TI 15/2007, p. 7 · TI 15/2007, p. 8 — MS 440 / MS 460: 2007 supply remarks are configuration-specific.
No additional parts-table entry added.
Service note · MS 361 / MS 362 / MS 440 / MS 441 / MS 460 / MS 650 / MS 660 / MS 880
MS 361, MS 362, MS 440, MS 441, MS 460, MS 650, MS 660, MS 880: magnesium stud adhesive changes to Loctite 270
Metric-thread crankcase studs: Loctite 243 (USA 242) → Loctite 270; not polymer housings.
- Exact listed magnesium-crankcase models: MS 361, MS 362, MS 440, MS 441, MS 460, MS 650, MS 660, MS 880. Their metric-thread studs change from Loctite 243 (USA: Loctite 242) to Loctite 270. No stud part number, serial changeover, cure time or torque is specified here.
- Before stud reassembly, clean BOTH threads: insert the tap into the internal thread BY HAND, then blow out the threaded hole; brush off the external stud thread. Coat the cleaned stud with Loctite 270. This thread-cleaning instruction is not permission to enlarge the polymer repair-stud hole.
- Loctite is NOT used for studs in polymer engine housings. The magnesium adhesive change does not override the separate polymer repair restrictions or give these models permission to use the oversized polymer repair studs.
- The repeated words engine housings at the end of page3 are present in the original scan; they add no second instruction and are not silently corrected in the retained source.
- Historical English TI29/2011. Only the printed model and material scope is admitted; no unlisted variants or predecessor models are inferred. No physical interchange test was performed.
Source: TI 29/2011, p. 3 — MS 361, MS 362, MS 440, MS 441, MS 460, MS 650, MS 660, MS 880: magnesium stud adhesive changes to Loctite 270.
No additional parts-table entry added.
Wrong number or missing part for the MS 460? Report a correction →