← 017/018 · MS 170/180

Stihl 1130 · Section A · 1 of 10 · 30 parts

Engine housing

Fits 017.

Parts diagrams →

Historical fitment & changes (7) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
110111213141516161718192202122232425262734456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (30)

PosPart numberDescriptionQty
1 1130 020 3002 Engine housing 1
1 1130 020 3001 Engine housing Fitment / change note → → replaced by 1130 020 3002 TI 5/2000 1
1 1130 020 3011 Engine housing Fitment / change note → 1
2 1120 162 5200 Pin 1
3 1123 162 5200 Pin 1
4 1123 162 5205 Pin 2
5 1123 664 2400 Collar screw 2
5 1123 664 2400 Collar screw 1
6 1121 122 6600 Collar screw 2
7 1123 791 2800 Annular buffer 2
8 1123 791 7300 Plug 2
9 1123 664 2402 NLA Collar screw 1
10 1123 640 3200 NLA Oil pump 0.55 1
11 1130 350 4400 Oil tank Fitment / change note → 1
12 0000 359 1241 Sealing ring 1
13 1130 647 9400 Hose 1
14 1123 640 3800 Pickup body 1
15 1130 350 0411 Fuel tank 1
16 0747 313 6810 Valve Fitment / change note → 2
17 1130 358 7701 Hose 1
18 9395 021 0760 Split pin 1.6x8 Fitment / change note → → replaced by 0747 313 6810 TI 12/1998 1
19 0000 350 3500 Pickup body 1
20 0000 989 0816 Grommet 1
21 4130 358 7600 Hose 1
22 0000 350 3502 Pickup body 1
23 1130 350 0500 Filler cap 2
24 0000 359 1240 Sealing ring 2
25 0000 350 0905 Rope 2
26 0000 353 0605 Hook 2
27 1130 791 5900 Stop buffer 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · 017

017 fuel, fixed-jet setting and leakage-test pressures

Low-speed screw one turn open; no adjustable high-speed screw or numeric maximum rpm supplied.

  • All-position diaphragm carburetor with integral fuel pump and fixed main jet; NO HIGH-SPEED SCREW. Main jet is NOT ADJUSTABLE and the TI says maximum engine speed is permanently set by it; no numeric maximum engine speed or adjustable H setting is supplied. Standard LOW-SPEED SCREW setting is ONE TURN OPEN.
  • Crankcase leakage test: gauge pressure 0.4 bar (5.8 psi); vacuum magnitude 0.4 bar (5.8 psi). Carburetor leakage test: gauge pressure 0.4 bar (5.8 psi). Vacuum is not a second positive pressure. The page does not supply a hold time, allowable decay or full test procedure.
  • Fuel tank capacity 0.25 l (0.53 US pt). Regular brand-name gasoline and two-stroke engine oil; USA/CAN minimum pump octane 89 UNLEADED; 50:1 with STIHL 50:1 two-stroke oil. Do not relabel pump octane as RON or generalize the named-oil ratio to unlisted oils.
  • Flat felt-mat air filter. Later 017 F sheet lists several carburetors (C1Q-S57C, C1Q-S43B and WT-325A); TI23 names none. These later catalog choices are not proof that all share this 1995 adjustment specification.
  • Historical TI guidance for model 017 as described in TI23/1995; shared series 1130 or tooling does not extend these specifications to 018, MS170, MS180 or later variants. No serial cutoff, present stock guarantee or physical interchange verification is implied. No hardware operation was performed.

Source: TI 23/1995, p. 3 — Sections 4.1 crankcase tests and 4.2 fuel system.

No additional parts-table entry added.

Service note · 017

017 chain drive and speed-controlled oiling

Six-tooth 3/8 P spur drive; the TI specifies no oil feed at idle.

  • Chain drive uses a SIX-TOOTH 3/8 P SPUR SPROCKET. Chain speed 18.6 m/s (61 ft/sec) at 10000 rpm WITH THIS SIX-TOOTH SPROCKET. That reference speed is not an idle speed, maximum-rpm limit or seven-tooth drive specification.
  • Speed-controlled reciprocating oil pump with NO OIL FEED AT IDLE SPEED. Oil tank capacity 0.15 l (0.32 US pt). No numeric delivery rate, adjustment range or oil-pump ordering number is printed here. The later 017 A catalog oil-pump label “0.55” does not supply the missing 1995 delivery specification.
  • Historical TI guidance for model 017 as described in TI23/1995; shared series 1130 or tooling does not extend these specifications to 018, MS170, MS180 or later variants. No serial cutoff, present stock guarantee or physical interchange verification is implied. No hardware operation was performed.

Source: TI 23/1995, p. 6 — Sections 4.4.3 and 4.4.4.

No additional parts-table entry added.

Service note · 017

017 fastener torques and DG-thread reuse

The same DG 5x24 thread has different crankcase and fan-housing torques.

  • Spline screws: IS-DG 4x20 ignition module/cylinder 5.0 Nm (3.7 lbf.ft); IS-DG 5x24 crankcase 9.5 Nm (7.0); IS-DG 5x24 fan housing/crankcase 4.5 Nm (3.3); IS-DG 5x26 crankcase/cylinder/bar mounting 9.5 Nm (7.0). Same thread size does NOT imply the same component torque.
  • M8 collar screw into crankcase 16.0 Nm (11.8 lbf.ft), secured with adhesive 0786 111 1101 (LOCTITE 243), per remark 1. M12x1L clutch collar nut 50.0 Nm (37.0): retain the LEFT-HAND thread suffix L.
  • M5 carburetor nut 3.5 Nm (2.6 lbf.ft); M5 muffler/cylinder nut 7.0 Nm (5.2); M8x1 flywheel collar nut 27.5 Nm (20.2); M14x1.25 spark plug 25.0 Nm (18.5). These figures are distinct from valve or bar-fastener values.
  • IS-P 4x12 hand guard/fan housing screw 1.7 Nm (1.25 lbf.ft). ONLY THIS ROW carries remark 2: torque may be reduced by approximately 1 Nm (0.7 lbf.ft) when refitting in an existing thread. Do not apply that reduction to every DG screw or all listed fasteners.
  • DG screws form a permanent thread in polymer on first installation. To reuse: turn COUNTERCLOCKWISE until the screw drops slightly into the existing thread, then clockwise to specified torque. A torque wrench is essential; cutting a new parallel thread is not the prescribed procedure.
  • The TI notes adhesive-secured screws are easier to release after heating adhesive with a hot-air blower/hair dryer; DO NOT OVERHEAT POLYMER COMPONENTS. No heating temperature/time is specified. This is retained historical guidance, not a performed repair.
  • Historical TI guidance for model 017 as described in TI23/1995; shared series 1130 or tooling does not extend these specifications to 018, MS170, MS180 or later variants. No serial cutoff, present stock guarantee or physical interchange verification is implied. No hardware operation was performed.

Source: TI 23/1995, p. 7 — Section 4.5, every torque row, DG refitting procedure and remarks.

Part numbers (1)
  • 0786 111 1101 — LOCTITE 243 adhesiveremark 1; M8 crankcase collar screw · 017; Section 4.5, every torque row, DG refitting procedure and remarks

Service note · 017

017 oil-pump tool: new 1130 puller/installer and corrected drilling figure

Existing 1123 tool needs modification; scan corrects 7.5 to 8.0.

  • New puller 1130 893 1400 is key2 for REMOVING the oil pump; installer 1130 893 1500 is key3 for INSTALLING it. Both are marked 1130 in the drawings and must be acquired for existing installing tool 1123 890 2200 (key1). They are not the pump itself or a standalone complete replacement tool.
  • Section 5.2 remark 1 requires modifying the ORIGINAL VERSION of 1123 890 2200 for items 2 and 3. Figure 143TI004 shows a new hole identified 1130 alongside the existing 1123 position; this is not drilling the saw housing.
  • The original scan explicitly CROSSES OUT 7,5 and corrects the hole size to 8,0 with a warning symbol. The extracted text loses the strike-through and does not convey that 7.5 is obsolete. The diagram also labels 62,2 from new-hole center to end-pivot center and 8 from the upper tool edge to the hole centerline. These are separate dimensions, not alternative hole sizes.
  • The figure does not print dimensional units, machining tolerances, material or a complete fixture setup. Conventional millimetre interpretation is plausible but is not silently promoted to a fully specified fabrication procedure. Preserve the original diagram for its datums; no tool was drilled or hardware operated.
  • Historical TI guidance for model 017 as described in TI23/1995; shared series 1130 or tooling does not extend these specifications to 018, MS170, MS180 or later variants. No serial cutoff, present stock guarantee or physical interchange verification is implied. No hardware operation was performed.

Source: TI 23/1995, p. 8 · TI 23/1995, p. 9 · TI 23/1995, p. 10 — Sections 5.1–5.2, remark 1 and figures 143TI004–006.

Part numbers (3)
  • 1130 893 1400 — Oil-pump pullerkey2; acquire for original installing tool · 017; Sections 5.1–5.2, remark 1 and figures 143TI004–006
  • 1130 893 1500 — Oil-pump installerkey3; acquire for original installing tool · 017; Sections 5.1–5.2, remark 1 and figures 143TI004–006
  • 1123 890 2200 — Oil-pump installing/removing toolkey1; original version requires modification · 017; Sections 5.1–5.2, remark 1 and figures 143TI004–006

Service note · 017

017 servicing aids: grease, low-temperature lubricant and HTR lead

Grease and starter lubricant have different listed applications.

  • Lubricating grease 0781 120 1111: oil seals, oil-pump drive, chain-sprocket bearing and switch shaft/contact spring. Low-temperature lubricant 0781 417 1315: REWIND STARTER. Do not silently interchange these application lists.
  • Ignition lead HTR, 10 m, is listed as 0000 930 2251 with a BLANK application cell. The 10 m is the listed lead supply length, not a required installed 017 lead length; no cutting length, resistance specification or additional application is supplied.
  • Historical TI guidance for model 017 as described in TI23/1995; shared series 1130 or tooling does not extend these specifications to 018, MS170, MS180 or later variants. No serial cutoff, present stock guarantee or physical interchange verification is implied. No hardware operation was performed.

Source: TI 23/1995, p. 10 — Section 5.3, all servicing-aid rows.

Part numbers (3)
  • 0781 120 1111 — Lubricating greaseoil seals, pump drive, sprocket bearing, switch shaft/contact spring · 017; Section 5.3, all servicing-aid rows
  • 0781 417 1315 — Low-temperature lubricantrewind starter · 017; Section 5.3, all servicing-aid rows
  • 0000 930 2251 — Ignition lead HTR, 10 mlisted supply length; application cell blank · 017; Section 5.3, all servicing-aid rows

Conditional replacement · 017 / 017 C

017 / 017 C: housing bushings require the matching screws

Revised housings use four DG screws; original housings must retain collar screws.

in progress — Housing introduction only; no serial cutoff. Original housings require collar screws; four-year inclusion is historical.

  • FOUR BUSHINGS will be pressed into the engine housing to optimize the housing/cylinder assembly. Housing 1130 020 3000 becomes 1130 020 3001 for 017; housing 1130 020 3010 becomes 1130 020 3011 for 017 C. These are separate model-specific replacements, not interchangeable housing variants.
  • FOUR DG screws 9075 478 4159 replace collar screws 1130 028 0200 in the modified assembly. The summary specifies IS-DG 5x24 (4x). Service restriction: COLLAR SCREWS MUST STILL BE USED IN ORIGINAL HOUSINGS. This is not permission to put DG screws into an old housing or to press in unspecified retrofit bushings; no bushing part number, drilling procedure or torque is supplied.
  • Each new housing includes four DG screws FOR THE NEXT FOUR YEARS, a historical temporary supply promise, not permanent present-day kit contents. Housing introduction is IN PROGRESS, with NO SERIAL CUTOFF. Original housings are supplied ONLY WHILE STOCKS LAST; the original collar screw REMAINS AVAILABLE AS A SPARE. The WT325A serial in section 3 does not govern the housings.
  • Exact 017 engine-housing IPL retains both 3001 and 3011 plus later 3002. The 017 cylinder sheet retains collar screw 1130 028 0200 with quantity 4 and DG screw 9075 478 4159 with quantity 8 and description IS-D5x24. Its assembly-wide quantity and wording do not replace this TI’s four-screw inclusion and IS-DG label. Later 3002 is not silently substituted for the TI housing; its later bulletin remains in the serial queue.
  • Historical TI 12/1998, model 017, series 1130; 017 C is expressly distinguished in the housing section. Shared parts do not extend these instructions to 018, MS170 or MS180. Factory supply statements are historical, not current availability. Source-stated repair permission is not physical-fit verification. No hardware operation was performed.

Source: TI 12/1998, p. 1 — Section 1 complete prose, service restriction, four summary rows, temporary screw inclusion and both supply remarks.

Part numbers (6)
  • 1130 020 3000 — Original 017 engine housingStock-limited original · 017 only
  • 1130 020 3001 — Modified 017 engine housingFour bushings; temporary four-DG-screw inclusion · 017 only
  • 1130 020 3010 — Original 017 C engine housingStock-limited original · 017 C only
  • 1130 020 3011 — Modified 017 C engine housingFour bushings; temporary four-DG-screw inclusion · 017 C only
  • 9075 478 4159 — Screw IS-DG 5x24Four for modified assembly · 017 / 017 C; original versus modified housing restriction applies
  • 1130 028 0200 — Original collar screwRequired in original housings; remains spare · 017 / 017 C; original versus modified housing restriction applies

Conditional replacement · 017

017: oil-tank vent valve retrofit requires a 3.4 mm hole

Same-number tank changes from split pin to valve; drilling, deburring and shavings removal are inseparable conditions.

in progress — Oil-tank production introduction; no serial supplied. Repair conversion has explicit hole preparation and cleaning requirements.

  • Split pin 9395 021 0760 (1.6x8) is replaced by valve 0747 313 6810 to improve the OIL TANK VENT. Oil tank 1130 350 4400 retains the SAME ORDER NUMBER. The summary says tank including items 2 and 3, but the original/new columns show ALTERNATIVE split-pin and valve versions, not both installed together.
  • For a REPAIR, the split pin CAN be replaced by the valve ONLY with the stated preparation: drill the oil-tank hole to DIAMETER 3.4 mm (0.134 in dia), carefully DEBURR OUTSIDE AND INSIDE with a UNIVERSAL COUNTERSINK, and REMOVE SHAVINGS FROM THE OIL TANK. Drawing 143TI011 KN places the drill at the vent boss beside the filler neck and labels the drill diameter; it does not specify a drilling depth or countersink angle. No added depth, angle or torque is inferred.
  • Introduction is IN PROGRESS, with NO SERIAL CUTOFF. ONLY THE MODIFIED TANK VERSION is available from the factory; the split pin REMAINS AVAILABLE FOR OTHER MODELS. Neither the unchanged tank number nor the retained pin proves an unmodified tank accepts the valve without preparation. The WT325A serial does not govern this change.
  • Exact 017 engine-housing IPL retains tank 1130 350 4400, valve 0747 313 6810 and split pin 9395 021 0760. The sheet includes both fuel and oil systems and lists valve quantity 2; that does not mean two valves belong in the oil-tank vent or authorize drilling a fuel tank. Its automated supersession sentence omits the repair conditions; this reviewed note retains them.
  • Historical TI 12/1998, model 017, series 1130; 017 C is expressly distinguished in the housing section. Shared parts do not extend these instructions to 018, MS170 or MS180. Factory supply statements are historical, not current availability. Source-stated repair permission is not physical-fit verification. No hardware operation was performed.

Source: TI 12/1998, p. 1 · TI 12/1998, p. 2 — Section 2 pages1–2 complete prose/service note, drawing 143TI011 KN, three summary rows and both remarks.

Part numbers (3)
  • 1130 350 4400 — Oil tank; same order numberOnly modified version supplied · 017; exact variant/component restrictions in this note
  • 9395 021 0760 — Original split pin 1.6x8Remains available for other models · 017; exact variant/component restrictions in this note
  • 0747 313 6810 — New oil-tank vent valveRepair retrofit requires 3.4 mm hole, deburring and cleaning · 017; exact variant/component restrictions in this note

Wrong number or missing part for the 017? Report a correction →