← FS 360, FS 420, FS 420 L · FS 500, FS 550, FS 550 L

Stihl 4116 · Section B · 2 of 12 · 33 parts

Rewind starter, Muffler

Fits FS 360, FS 420, FS 420 L.

Parts diagrams →

Historical fitment & changes (4) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1101112131415151617181922021222324252627282933031456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (33)

PosPart numberDescriptionQty
1 4116 190 0400 Starter cover 1
2 0000 967 2035 Nameplate STIHL 1
3 1110 084 9102 Bushing 1
4 9416 868 6630 Hollow rivet 6.5x0.5x6.8 4
5 4116 190 0600 Rewind spring 1
6 4119 195 0400 Rope rotor 1
7 0000 190 3401 Starter grip ElastoStart Ø 3.5 mm 1
8 1113 195 8200 Starter rope Ø 3.5x960 mm Fitment / change note → 1
9 0000 195 7001 Cap 1
10 4116 195 7200 Pawl 1
11 0000 958 0923 Washer 1
12 1118 195 3500 Spring 1
13 9210 261 1140 Hexagon nut M8x1 1
14 4223 195 0600 Starter cup Fitment / change note → 1
15 9022 371 1020 Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 6
16 4116 145 0600 Heat shield 1
17 9022 313 0610 Spline screw IS-M4x6 3
18 4116 149 0600 Muffler gasket 1
19 4116 140 0606 Muffler 1
20 4116 140 0601 Muffler 1
21 4116 141 9000 Screen 1
22 4116 145 0605 Deflecting plate 1
23 9041 216 0650 Pan head screw M4x10 2
24 9022 371 1020 Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 2
25 9291 021 0120 Washer 5.3 2
26 9099 021 0810 Self-tapping screw 4.2x9.5 2
27 0000 958 0806 Washer 1
28 9022 341 1150 Spline screw IS-M5x65 2
29 4116 148 3000 Shim 1
30 1128 190 2900 Starter rope Ø 3.5 mm Fitment / change note → 1
31 0000 974 1000 Round head rivet 3x6 2
Not numbered on the diagram — assemblies, kits and options
— 0000 930 2203 Starter rope Ø 3.5 mm x 30.5 m Fitment / change note → not illustratedoption 1
— 0000 930 2267 Starter rope Ø 3.5 mm / 28 pieces Fitment / change note → 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · FS 360 / FS 420

FS 360 / FS 420: modified starter cup and retained old-cup suitability

Starter cup renumbering is in progress; other changeover cutoffs in this TI do not apply.

  • Starter cup 4116 195 0500 was modified during development of new models and renumbered 4223 195 0600. Introduction is IN PROGRESS; no numeric cutoff is given. New MOQ 10 is an order quantity, not ten installed cups. The old cup is no longer factory available, but the text explicitly retains its replacement suitability.
  • Both modified AND original cups should also be used as replacements for the printed scope “FS 160 through FS 280” and BR 320/400, SR 320/400. This is not every numeric FS model, every model sharing a part number, or proof of suitability for FS 290, FS 500/550, FR 220 or later successors. No dimensional change or installation torque is provided.
  • Historical TI 48/1994 guidance, not current stock or verified physical interchange. Shared IPL sheets do not extend the named source models or variants. No hardware operation was performed.

Source: TI 48/1994, p. 4 — modified starter cup and retained old-cup suitability.

Part numbers (2)
  • 4116 195 0500 — Original starter cupalso suitable as described; no longer factory available · FS 360 / FS 420 only in the configuration described here
  • 4223 195 0600 — Modified starter cupMOQ 10; introduction in progress · FS 360 / FS 420 only in the configuration described here

Conditional replacement · FS 160 / FS 180 / FS 220 / FS 280 / FS 360 / FS 420 / BR 320 / BR 400 / SR 320 / SR 400

FS / BR / SR starter cup: old and new replacement scope

Modified cup 4223 195 0600 replaces 4116 195 0500; both versions are stated replacements for the additional named models.

  • In the cover scope FS160/180/220/280, starter cup 4116 195 0500 is modified during development of unspecified new models and renumbered 4223 195 0600. The TI explicitly says the modified cup AND THE ORIGINAL VERSION can ALSO be used as replacements for FS360, FS420, BR320/400 and SR320/400. It does not identify the new development models or authorize arbitrary starter-assembly interchange.
  • Introduction is IN PROGRESS; no serial marker is supplied for this change. The nameplate serial on the same page belongs to section 3, not this cup. New cup MOQ 10 is an order minimum. The ORIGINAL cup is NO LONGER AVAILABLE FROM THE FACTORY; historical replacement suitability does not promise continued supply.
  • Later exact-model rewind-starter sheets show 4223 195 0600 at key 1 for the 4119 and 4203 model groups and key 14 for FS360/420. Shared-sheet FS220 K, FS280 K, FS290, FS420 L and BR320 L are not silently added to this TI note. No cup dimensions or mounting torque are provided.
  • Historical TI guidance for the explicitly named models and stated versions only. Shared IPL sheets are navigation, not an extension to every listed variant or proof of unrestricted interchange. Supply statements are historical, not current stock guarantees. No hardware operation was performed.

Source: TI 16/1995, p. 3 · TI 16/1995, p. 4 — Section 4: starter-cup replacement scope, table and supply remark.

Part numbers (2)
  • 4116 195 0500 — Original starter cupreplacement suitability retained; no longer supplied · FS 160; FS 180; FS 220; FS 280; FS 360; FS 420; BR 320; BR 400; SR 320; SR 400
  • 4223 195 0600 — Modified starter cupnew; MOQ 10; explicitly stated replacement scope · FS 160; FS 180; FS 220; FS 280; FS 360; FS 420; BR 320; BR 400; SR 320; SR 400

Historical fitment · FS 360

FS 360: standard ElastoStart from X 32 701 029

Rubber-element grip 1128 190 3400 replaces standard grip 1121 195 3400.

X 32 701 029 — Standard ElastoStart starter grip introduced from this machine number on the named series 4119 models; not the other section changeover.

  • From machine number X 32 701 029 FS 360 (series 4116) comes STANDARD with ElastoStart. This is not the optional spring-type 0000 190 3400 of TI 07/1996.
  • The three named components are starter grip, RUBBER ELEMENT and starter rope. New ElastoStart grip 1128 190 3400 replaces original 1121 195 3400 for this change. Remark 1 retains the original grip for older machines and other models; it is not a universal-deletion statement.
  • The bulletin expressly delegates construction, function and benefits to TI 29/1992. That source is absent from the retained 690 entries and mounted tipages inventory (1992-29-*); the dependency remains a documented source gap, not a complete account of rubber-element construction. No spring-type instructions from TI 07/1996 are substituted.
  • Historical TI 09/1996 guidance for FS 360 only. The FS 420 nameplate table row does not extend starter or cap guidance to FS 420; shared IPL sheets do not add FS 420 L, FS 500 or FS 550. No hardware operation was performed; supply statements are historical, not current stock. Starter, cap and nameplate serials are independent.

Source: TI 9/1996, p. 1 — FS 360: standard ElastoStart from X 32 701 029.

Part numbers (2)
  • 1121 195 3400 — Original starter gripretained for older machines and other models · FS 360; TI09/1996 stated configuration
  • 1128 190 3400 — ElastoStart starter gripnew standard rubber-element version · FS 360; TI09/1996 stated configuration

Historical fitment · FS 360

FS 360: ElastoStart rope and accessory supply

New 1128 190 2900 rope is Ø3.5 mm; do not transfer old 960 mm length.

X 32 701 029 — Standard ElastoStart starter grip introduced from this machine number on the named series 4119 models; not the other section changeover.

  • Original rope 1113 195 8200 is explicitly Ø3.5 x 960 mm. New rope 1128 190 2900 is printed ONLY Ø3.5 mm. No new length is specified, so the old 960 mm value is not copied to it. Original rope remains available for older machines and other models (remark 1).
  • Special-accessory original rope 0000 930 2203 is listed as 30.5 m and retains availability for older machines/other models (remarks 1/2). New special-accessory rope 0000 930 2267 is Ø3.5 mm (28 x), remark 2. The printed 28 x qualifier is preserved; no per-piece length,30.5 m total or cutting scheme is invented.
  • Table dashes mark original/new columns; they do not cancel the explicit original-parts availability remarks. The source does not say the new grip package includes these separately listed ropes.
  • Historical TI 09/1996 guidance for FS 360 only. The FS 420 nameplate table row does not extend starter or cap guidance to FS 420; shared IPL sheets do not add FS 420 L, FS 500 or FS 550. No hardware operation was performed; supply statements are historical, not current stock. Starter, cap and nameplate serials are independent.

Source: TI 9/1996, p. 1 — FS 360: ElastoStart rope and accessory supply.

Part numbers (4)
  • 1113 195 8200 — Original rope Ø3.5 x 960 mmretained older-machine/other-model supply · FS 360; TI09/1996 stated configuration
  • 1128 190 2900 — New rope Ø3.5 mmnew length unspecified · FS 360; TI09/1996 stated configuration
  • 0000 930 2203 — Original 30.5 m ropespecial accessory; retained original supply · FS 360; TI09/1996 stated configuration
  • 0000 930 2267 — New rope Ø3.5 mm (28 x)special accessory;28 x as printed · FS 360; TI09/1996 stated configuration

Wrong number or missing part for the FS 360, FS 420, FS 420 L? Report a correction →