← FS 360, FS 420, FS 420 L · FS 500, FS 550, FS 550 L

Stihl 4116 · Section A · 1 of 12 · 39 parts

Crankcase, Cylinder

Fits FS 360, FS 420, FS 420 L.

Parts diagrams →

Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.

This drawing carries 2 bore sizes — Ø 44 mm , Ø 46 mm . Not interchangeable — measure your cylinder before ordering. The catalogue lists them on one sheet for one machine and never says which variant each belongs to, so this guide does not either.

Position —

Go to table row → Where else is this used →
111011121314151617181922021222324252627282934404141424344454656789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (39)

PosPart numberDescriptionQty
1 4116 020 2116 Crankcase Fitment / change note → 1
2 9371 470 2610 Cylindrical pin 5x18 2
3 1110 122 3900 Elbow connector 1
4 9523 003 4260 Grooved ball bearing 15x35x13 1
5 9465 620 2620 Snap ring 37 1
6 9503 003 0340 Grooved ball bearing 6202 → replaced by 9503 003 0346 TI 6/2001 1
7 9022 371 1020 Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 4
8 4116 029 0500 Gasket 1
9 9640 003 1600 Oil seal 15x29.6x4 1
10 9640 003 1340 Oil seal 13x22x5 1
11 4116 030 0400 Crankshaft 1
12 1120 036 8500 Woodruff key 2x3.7 1
13 4116 029 2305 Cylinder gasket Fitment / change note → 1
13 4116 029 2306 Cylinder gasket 1 mm 1
14 9512 003 2340 Needle cage 10x14x13 1
15 4116 020 1203 Cylinder with piston Ø 44 mm Fitment / change note → 1
16 4116 020 1215 Cylinder with piston Ø 46 mm Fitment / change note → 1
17 4116 030 2000 Piston Ø 44 mm Fitment / change note → 1
18 4116 030 2005 Piston Ø 46 mm 1
19 4116 034 3000 Piston ring Ø 44x1.2 mm Fitment / change note → 2
20 4116 034 3005 Piston ring Ø 46x1.2 mm 2
21 1110 034 1500 Piston pin 10x6x32 1
22 9463 650 1000 Snap ring 10 2
23 9022 341 0900 Spline screw IS-M5x28 4
24 1110 400 7005 Spark plug Bosch WSR 6 F 1
24 0000 400 7000 Spark plug NGK BPMR7A 1
25 0000 998 0603 Torsion spring → replaced by 0000 998 0604 TI 30/1995 1
26 1106 405 1000 Spark plug boot → replaced by 1128 405 1000, 1128 405 1000 TI 30/1995 1
27 9025 313 0741 Spline screw M4x25 1
28 not sold separately Cover not available as a separate item 1
29 4116 149 0600 Muffler gasket 1
40 1110 034 3000 Piston ring Ø 44x1.5 mm 2
41 4116 020 2105 Crankcase Fitment / change note → 1
42 4116 029 2300 Cylinder gasket Fitment / change note → 1
43 4116 020 1201 Cylinder with piston Ø 44 mm Fitment / change note → 1
44 4116 431 2500 Cable clamp 1
45 9074 478 3025 Pan head self-tapping screw IS-P4x16 2
46 4116 404 7800 Screw M4x16 1
Not numbered on the diagram — assemblies, kits and options
— 4116 007 1051 Set of gaskets 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · FS 360

FS 360: cylinder hole pattern changes at X 28 698 911

New crankcase, gasket and 44 mm cylinder/piston must be used together for post-cutoff repairs.

X 28 698 911 — Printed introduction for this component only; not a universal machine cutoff or interchange guarantee.

  • From FS 360 machine X 28 698 911, cylinder-to-crankcase hole pattern matches FS 420. Crankcase 4116 020 2115 and cylinder gasket 4116 029 2305, previously used only for FS 420, now also fit the revised FS 360. New FS 360 cylinder with 44 mm piston is 4116 020 1202; sharing the hole pattern does NOT establish FS 420 cylinder interchange.
  • For FS 360 repairs FROM X 28 698 911, MUST use crankcase 4116 020 2115, gasket 4116 029 2305 and cylinder/piston 4116 020 1202. Original crankcase 4116 020 2105, cylinder/piston 4116 020 1201 and gasket 4116 029 2300 REMAIN available for machines PRIOR TO that number. No mixed-pattern assembly or blanket retrofit across the boundary is admitted.
  • Included piston 4116 030 2000 and its ring 4116 034 3000 keep their numbers; all other parts as before. The table does not assign new numbers to these unchanged internal parts.
  • Historical TI 18/1994 guidance for explicitly named models only; no successor or unlisted variant applicability inferred. Factory supply statements are historical, not current stock claims. MOQ columns are order quantities, not fitting quantities. No physical interchange test was performed.

Source: TI 18/1994, p. 3 — FS 360: cylinder hole pattern changes at X 28 698 911.

Part numbers (8)
  • 4116 020 2105 — Original FS 360 crankcaseretained for earlier machines · FS 360: cylinder hole pattern changes at X 28 698 911
  • 4116 020 2115 — Revised FS 360 crankcaseshared with FS 420; required from cutoff · FS 360: cylinder hole pattern changes at X 28 698 911
  • 4116 020 1201 — Original cylinder with pistonretained for earlier machines · FS 360: cylinder hole pattern changes at X 28 698 911
  • 4116 020 1202 — New cylinder with 44 mm pistonrequired from cutoff · FS 360: cylinder hole pattern changes at X 28 698 911
  • 4116 029 2300 — Original cylinder gasketretained for earlier machines · FS 360: cylinder hole pattern changes at X 28 698 911
  • 4116 029 2305 — Revised cylinder gasketshared with FS 420; required from cutoff · FS 360: cylinder hole pattern changes at X 28 698 911
  • 4116 030 2000 — Pistonunchanged; included · FS 360: cylinder hole pattern changes at X 28 698 911
  • 4116 034 3000 — Piston ringunchanged; included · FS 360: cylinder hole pattern changes at X 28 698 911

Service note · FS 550 / FS 360 / FS 420

FS 550 TI 44: 44 mm and 46 mm cylinder rows remain distinct

The new-spares table lists both bores; it does not approve a bore conversion.

  • Items 1–6 retain the exact numbers shown below. Ignition module item 5 INCLUDES grommet item 6. No inclusion of the decompression valve in either cylinder assembly is explicitly stated.
  • The FS 550 specification on page 3 says 46 mm bore, yet the page 10 table lists BOTH 44 mm and 46 mm cylinder-with-piston assemblies. Preserve both entries without calling the 44 mm assembly the FS 550 production cylinder or approving a displacement conversion. The table does not explain this model-allocation ambiguity.
  • Remark 1 explicitly makes items 1, 2, 3 spare parts for predecessor FS 360 and FS 420 as well. It does NOT attach to items 4, 5, 6. This is a scoped source assertion, not proof that either cylinder can replace every predecessor cylinder without other changes.
  • Historical TI 44/1997 source guidance, not current availability, verified physical interchange or a complete repair procedure. Shared IPL sheets do not extend claims to unnamed variants. No hardware operation was performed.

Source: TI 44/1997, p. 3 · TI 44/1997, p. 10 — Section7 rows1–6 and remark1, compared with section2.1.1 specification.

Part numbers (6)
  • 4116 020 2116 — Item1 crankcase; remark1New-spares table; bore/model restriction retained · FS 550 table context; remark1 also names FS 360 and FS 420; preserve assembly/bore restrictions
  • 4116 020 1203 — Item2 cylinder with piston44 mm; remark1New-spares table; bore/model restriction retained · 44 mm table entry; FS 550 production allocation unresolved against46 mm specification; remark1 names FS 360/FS 420; no bore conversion approval
  • 4116 020 1215 — Item3 cylinder with piston46 mm; remark1New-spares table; bore/model restriction retained · FS 550 table context; remark1 also names FS 360 and FS 420; preserve assembly/bore restrictions
  • 1128 020 9400 — Item4 decompression valveNew-spares table; bore/model restriction retained · FS 550 table context; no separate predecessor remark on this row
  • 4116 400 1306 — Item5 ignition module including item6New-spares table; bore/model restriction retained · FS 550 table context; no separate predecessor remark on this row
  • 0000 989 1010 — Item6 grommetNew-spares table; bore/model restriction retained · FS 550 table context; no separate predecessor remark on this row

Wrong number or missing part for the FS 360, FS 420, FS 420 L? Report a correction →