← FS 360, FS 420, FS 420 L · FS 500, FS 550, FS 550 L

Stihl 4116 · Section A · 1 of 16 · 28 parts

Crankcase, Cylinder

Fits FS 500, FS 550, FS 550 L.

Parts diagrams →

Historical fitment & changes (4) — includes parts and conditions not shown on this drawing.

This drawing carries 2 bore sizes — Ø 44 mm , Ø 46 mm . Not interchangeable — measure your cylinder before ordering. The catalogue lists them on one sheet for one machine and never says which variant each belongs to, so this guide does not either.

Position —

Go to table row → Where else is this used →
11101112131415161718192202122232425263456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (28)

PosPart numberDescriptionQty
1 4116 020 2116 Crankcase Fitment / change note → 1
2 9371 470 2610 Cylindrical pin 5x18 2
3 1110 122 3900 Elbow connector 1
4 9523 003 4260 Grooved ball bearing 15x35x13 1
5 9465 620 2620 Snap ring 37 1
6 9503 003 0340 Grooved ball bearing 6202 → replaced by 9503 003 0346 TI 6/2001 1
7 9022 371 1020 Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 4
8 4116 029 0500 Gasket 1
9 9640 003 1600 Oil seal 15x29.6x4 1
10 9640 003 1340 Oil seal 13x22x5 1
11 4116 030 0400 Crankshaft 1
12 1120 036 8500 Woodruff key 2x3.7 1
13 4116 029 2305 Cylinder gasket 1
14 9512 003 2340 Needle cage 10x14x13 1
15 4116 020 1203 Cylinder with piston Ø 44 mm Fitment / change note → 1
16 4116 020 1215 Cylinder with piston Ø 46 mm Fitment / change note → 1
17 4116 030 2000 Piston Ø 44 mm 1
18 4116 030 2005 Piston Ø 46 mm 1
19 4116 034 3000 Piston ring Ø 44x1.2 mm 2
20 4116 034 3005 Piston ring Ø 46x1.2 mm 2
21 1110 034 1500 Piston pin 10x6x32 1
22 9463 650 1000 Snap ring 10 2
23 9022 341 0900 Spline screw IS-M5x28 4
24 0000 400 7000 Spark plug NGK BPMR7A 1
24 1110 400 7005 Spark plug Bosch WSR 6 F 1
25 1128 020 9400 Decompression valve Fitment / change note → 1
26 4116 149 0600 Muffler gasket 1
Not numbered on the diagram — assemblies, kits and options
— 4116 007 1051 Set of gaskets 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · FS 550

FS 550: engine limits, single-pawl starter and ElastoStart

56.5 cc engine; 12,500 rpm cut-off without a cutting tool is not the rated output-shaft speed.

  • Engine: displacement 3.45 cu.in (56.5 cc), bore 1.81 in (46 mm), stroke 1.34 in (34 mm), power to ISO 8893 of 3.8 bhp (2.8 kW). These FS 550 specifications do not resolve the separate 44 mm/46 mm spare-cylinder rows on page 10 or establish a bore-conversion approval.
  • Idle is 2,500 rpm; clutch engages at 3,250 rpm. ELECTRONIC CUT-OFF WITHOUT CUTTING TOOL is 12,500 rpm (+/- 800 rpm). Maximum RATED OUTPUT-SHAFT speed is 9,400 rpm. Keep crankshaft/cut-off and output-shaft speeds distinct; the no-tool test condition is not authorization to run a machine unattended.
  • The rewind starter uses a SINGLE PAWL and ElastoStart grip. Starter rope diameter is 0.14 in (3.5 mm); no rope length or part number is supplied in these sections. Easy start combines a decompression valve, ElastoStart grip and MANUAL FUEL PUMP; this is not a claim for a later spring-assisted starting system.
  • Historical TI44/1997 guidance for the named FS 550 configuration only. Shared IPL sheets do not extend these claims to FS 500, FS 550 L, FS 360 or FS 420. Not current stock, verified physical interchange or a complete operating procedure. No hardware operation was performed.

Source: TI 44/1997, p. 1 · TI 44/1997, p. 2 · TI 44/1997, p. 3 — Section 1 cylinder/easy start and section 2.1.1 full engine specification.

No additional parts-table entry added.

Service note · FS 550

FS 550: clamp-style throttle adjustment and leak-test pressures

Engine pressure/vacuum is±0.5 bar; carburetor inlet needle is tested at 0.8 bar.

  • In 398TI 004 KN, screw(1) secures cover(2) and its cable clamp. Slacken screw about TWO OR THREE TURNS until the cover releases the clamp. Hold the throttle trigger fully squeezed, retighten the screw to secure the clamp, THEN release the trigger. This is the printed full-throttle adjustment, not a later throttle-cable design or an engine-running instruction.
  • Engine leak test: PRESSURE +7.25 psi(+0.5 bar); VACUUM -7.25 psi(-0.5 bar). Carburetor INLET NEEDLE testing pressure: 11.6 psi(0.8 bar). No dwell time, allowed pressure drop, isolation setup or needle leakage threshold is supplied here. Do not turn these three values into a complete test or use the carburetor pressure for the crankcase.
  • If started during repairs/maintenance, the source requires observing local/national safety regulations and owner-manual precautions. It delegates repairs to a service manual; servicing the carburetor, troubleshooting and standard procedures are described in SEPARATE HANDBOOKS, not that manual. The owner manual and these separate handbooks have not been reviewed as complete procedures in this note.
  • Historical TI 44/1997 source guidance, not current availability, verified physical interchange or a complete repair procedure. Shared IPL sheets do not extend claims to unnamed variants. No hardware operation was performed.

Source: TI 44/1997, p. 8 — Section6 repairs context, complete6.1.1 adjustment/398TI004 KN and6.2 leakage-test data.

No additional parts-table entry added.

Service note · FS 550

FS 550: all 20 historical repair-time entries

Decimal hours, with 0.1 hour equal to 6 minutes; trained and equipped workshop assumed.

  • The times assume TRAINED PERSONNEL in a PROPERLY EQUIPPED SERVICE WORKSHOP. Values are decimal hours in tenths: 0.1 hour=6 minutes, not one minute. This table supplements the STIHL repair-times table; it is not a guarantee, current billing schedule or permission to add overlapping operations.
  • Code 1: Crankcase, short block — 2.0 hours.
  • Code 2: Crankshaft and/or bearings — 2.0 hours.
  • Code 3: Crankcase, gasket, sealing — 2.0 hours.
  • Code 4: Crankshaft seals — 1.2 hours.
  • Code 5: Cylinder and/or piston — 1.0 hours.
  • Code 6: Ignition — 0.5 hours.
  • Code 7: Fuel hose, fuel supply — 0.3 hours.
  • Code 8: Gear box, arbor assembly — 0.3 hours.
  • Code 9: Carburetor — 0.7 hours.
  • Code 10: Fan housing, clutch housing — 0.5 hours.
  • Code 11: Front handle, throttle — 0.4 hours.
  • Code 12: Recoil starter — 0.4 hours.
  • Code 13: Clutch — 0.5 hours.
  • Code 14: Drive tube, drive shaft — 0.5 hours.
  • Code 15: Muffler — 0.3 hours.
  • Code 16: Air filter, filter cover — 0.2 hours.
  • Code 17: Stop switch — 0.3 hours.
  • Code 18: Fuel tank — 0.8 hours.
  • Code 19: Replace arbor gears — 0.6 hours.
  • Code 20: Miscellaneous repairs — 0.5 hours.
  • Historical TI 44/1997 source guidance, not current availability, verified physical interchange or a complete repair procedure. Shared IPL sheets do not extend claims to unnamed variants. No hardware operation was performed.

Source: TI 44/1997, p. 9 — Complete section6.4: all20 codes, units and workshop assumptions.

No additional parts-table entry added.

Service note · FS 550 / FS 360 / FS 420

FS 550 TI 44: 44 mm and 46 mm cylinder rows remain distinct

The new-spares table lists both bores; it does not approve a bore conversion.

  • Items 1–6 retain the exact numbers shown below. Ignition module item 5 INCLUDES grommet item 6. No inclusion of the decompression valve in either cylinder assembly is explicitly stated.
  • The FS 550 specification on page 3 says 46 mm bore, yet the page 10 table lists BOTH 44 mm and 46 mm cylinder-with-piston assemblies. Preserve both entries without calling the 44 mm assembly the FS 550 production cylinder or approving a displacement conversion. The table does not explain this model-allocation ambiguity.
  • Remark 1 explicitly makes items 1, 2, 3 spare parts for predecessor FS 360 and FS 420 as well. It does NOT attach to items 4, 5, 6. This is a scoped source assertion, not proof that either cylinder can replace every predecessor cylinder without other changes.
  • Historical TI 44/1997 source guidance, not current availability, verified physical interchange or a complete repair procedure. Shared IPL sheets do not extend claims to unnamed variants. No hardware operation was performed.

Source: TI 44/1997, p. 3 · TI 44/1997, p. 10 — Section7 rows1–6 and remark1, compared with section2.1.1 specification.

Part numbers (6)
  • 4116 020 2116 — Item1 crankcase; remark1New-spares table; bore/model restriction retained · FS 550 table context; remark1 also names FS 360 and FS 420; preserve assembly/bore restrictions
  • 4116 020 1203 — Item2 cylinder with piston44 mm; remark1New-spares table; bore/model restriction retained · 44 mm table entry; FS 550 production allocation unresolved against46 mm specification; remark1 names FS 360/FS 420; no bore conversion approval
  • 4116 020 1215 — Item3 cylinder with piston46 mm; remark1New-spares table; bore/model restriction retained · FS 550 table context; remark1 also names FS 360 and FS 420; preserve assembly/bore restrictions
  • 1128 020 9400 — Item4 decompression valveNew-spares table; bore/model restriction retained · FS 550 table context; no separate predecessor remark on this row
  • 4116 400 1306 — Item5 ignition module including item6New-spares table; bore/model restriction retained · FS 550 table context; no separate predecessor remark on this row
  • 0000 989 1010 — Item6 grommetNew-spares table; bore/model restriction retained · FS 550 table context; no separate predecessor remark on this row

Wrong number or missing part for the FS 500, FS 550, FS 550 L? Report a correction →