Stihl 4116 · Section B · 2 of 16 · 29 parts
Rewind starter, Muffler
Fits FS 500, FS 550, FS 550 L.
Historical fitment & changes (5) — includes parts and conditions not shown on this drawing.
Parts (29)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4116 190 0400 | Starter cover | 1 |
| 2 | 0000 967 2035 | Nameplate STIHL | 1 |
| 3 | 1110 084 9102 | Bushing | 1 |
| 4 | 9416 868 6630 | Hollow rivet 6.5x0.5x6.8 | 4 |
| 5 | 4116 190 0600 | Rewind spring | 1 |
| 6 | 4119 195 0400 | Rope rotor | 1 |
| 7 | 0000 190 3401 | Starter grip ElastoStart Ø 3.5 mm Fitment / change note → | 1 |
| 8 | 1113 195 8200 | Starter rope Ø 3.5x960 mm Fitment / change note → | 1 |
| 9 | 0000 195 7001 | Cap | 1 |
| 10 | 0000 195 7200 | Pawl | 1 |
| 11 | 0000 958 0923 | Washer | 1 |
| 12 | 1118 195 3500 | Spring | 1 |
| 13 | 9210 261 1140 | Hexagon nut M8x1 | 1 |
| 14 | 4223 195 0600 | Starter cup | 1 |
| 15 | 9022 371 1020 | Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 | 6 |
| 16 | 4116 145 0600 | Heat shield | 1 |
| 17 | 9022 313 0610 | Spline screw IS-M4x6 | 3 |
| 18 | 4116 149 0600 | Muffler gasket | 1 |
| 19 | 4116 140 0606 | Muffler | 1 |
| 20 | 4116 140 0601 | Muffler | 1 |
| 21 | 4116 141 9000 | Screen | 1 |
| 22 | 4116 145 0605 | Deflecting plate | 1 |
| 23 | 9041 216 0650 | Pan head screw M4x10 | 2 |
| 24 | 9022 371 1020 | Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 | 2 |
| 25 | 9291 021 0120 | Washer 5.3 | 2 |
| 26 | 9099 021 0810 | Self-tapping screw 4.2x9.5 | 2 |
| 27 | 1128 190 2900 | Starter rope Ø 3.5 mm Fitment / change note → | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 0000 930 2203 | Starter rope Ø 3.5 mm x 30.5 m option | 1 |
| — | 0000 930 2267 | Starter rope Ø 3.5 mm / 28 pieces | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · FS 550
FS 550: engine limits, single-pawl starter and ElastoStart
56.5 cc engine; 12,500 rpm cut-off without a cutting tool is not the rated output-shaft speed.
- Engine: displacement 3.45 cu.in (56.5 cc), bore 1.81 in (46 mm), stroke 1.34 in (34 mm), power to ISO 8893 of 3.8 bhp (2.8 kW). These FS 550 specifications do not resolve the separate 44 mm/46 mm spare-cylinder rows on page 10 or establish a bore-conversion approval.
- Idle is 2,500 rpm; clutch engages at 3,250 rpm. ELECTRONIC CUT-OFF WITHOUT CUTTING TOOL is 12,500 rpm (+/- 800 rpm). Maximum RATED OUTPUT-SHAFT speed is 9,400 rpm. Keep crankshaft/cut-off and output-shaft speeds distinct; the no-tool test condition is not authorization to run a machine unattended.
- The rewind starter uses a SINGLE PAWL and ElastoStart grip. Starter rope diameter is 0.14 in (3.5 mm); no rope length or part number is supplied in these sections. Easy start combines a decompression valve, ElastoStart grip and MANUAL FUEL PUMP; this is not a claim for a later spring-assisted starting system.
- Historical TI44/1997 guidance for the named FS 550 configuration only. Shared IPL sheets do not extend these claims to FS 500, FS 550 L, FS 360 or FS 420. Not current stock, verified physical interchange or a complete operating procedure. No hardware operation was performed.
Source: TI 44/1997, p. 1 · TI 44/1997, p. 2 · TI 44/1997, p. 3 — Section 1 cylinder/easy start and section 2.1.1 full engine specification.
No additional parts-table entry added.
Historical fitment · FS 550 / BR 320 / BR 400 / SR 320 / SR 400
FS 550 / BR-SR 320, 400: ElastoStart retrofit set
New 3.5 mm set replaces the older ElastoStart; no serial cutoff is printed for these models.
- The TI expressly permits backfitting to its named models. First-time installation needs BOTH the appropriate grip and starter rope; no further changes to the rewind starter mechanism are required. This is not permission to mix rope diameters, omit the rope, or apply the change to every model using an old part number.
- Summary items5–8 distinguish the previous ElastoStart 1128 190 3400 including rope1128 190 2900 from new grip0000 190 3401 including rope1113 195 8200. Both OLD rows carry remark1: remain available as spares. The old rope is specified only as diameter3.5 mm; do not assign the new rope length960 mm to it. New rope is diameter3.5 mm x960 mm (37.75 in).
- The 020 T uses a different 3.0 mm x800 mm set. The part prefix does not determine model fitment. No reverse interchange or coil-spring internal substitution is stated.
- Introduction is in progress for FS550 and BR/SR320,400. Do not copy the026 cutoff1 40 743 432 onto these machines. The summary states no separate cutoff for any of them.
- Retained shared starter sheets list the new grip and rope. Their wider FS500/550L and BR320L headings do not extend TI41 scope. The derived TI43/1999 link to0000 190 3402 on BR/SR standard-grip rows was an019T-only assertion misapplied by part number;those unsupported links are removed. TI43 heading and section2 establish019T only,not BR/SR replacement.
- Historical TI 41/1998 only: 020 T (series 1129), 026 (1121), FS 550 (4116), BR/SR 320 and 400 (4203). The original scan prints 1129 for 020 T; its extracted body truncates this to 112. Shared later catalog sheets do not extend this TI to 020/020 AV, 024, FS 500/550 L, BR 320 L, MS successors or other models. Availability is historical, not current stock. No hardware operation was performed.
Source: TI 41/1998, p. 1 · TI 41/1998, p. 3 — Introduction; larger-model summary items5–8 and in-progress changeover qualifier.
Referenced bulletin evidence: TI 43/1999, p. 1 · TI 43/1999, p. 2 — Page1 model019T/series1132 heading;page2 complete section2 ElastoStart and four-row summary,serial and spare remark only;remaining TI not semantically reviewed.
Part numbers (4)
- 1128 190 3400 — Previous ElastoStart grip including original ropeOriginal remains spare · 026, FS 550, BR/SR 320,400
- 1128 190 2900 — Previous starter rope, diameter3.5 mmOriginal remains spare · 026, FS 550, BR/SR 320,400
- 0000 190 3401 — New ElastoStart grip including rope1113 195 8200New complete grip and rope · 026, FS 550, BR/SR 320,400
- 1113 195 8200 — New starter rope, diameter3.5 mm x960 mm (37.75 in)New rope; included with grip · 026, FS 550, BR/SR 320,400
Service note · 020 T / 026 / FS 550 / BR 320 / BR 400 / SR 320 / SR 400
ElastoStart: spring action and complete-grip servicing
The internal spring smooths compression peaks; the TI limits repairs to grip and rope replacement.
- Figures000TI028 KN and000TI029 KN identify grip1,cap2,sleeve3,coil spring4,two washers5 and rope6. In the idle position the sleeve,spring and washers are inside the grip. During pulling the force path is grip → lower washer → coil spring → upper washer → sleeve → rope.
- The TI describes rising spring tension with compression pressure and nearly uniform grip force after the first compression stroke. Graph000TI007 KN compares ElastoStart with the standard grip without numerical axes or units; it does not establish a measured percentage reduction or starting-speed specification.
- When pull exceeds the spring-defined limit,the spring becomes fully compressed and force passes directly from grip to rope. No numerical spring load or test specification is given. The grip spring is not the separate rewind spring in the starter housing.
- The historical service note supplies the ElastoStart grip only as a complete replacement unit and limits repairs to grip and starter rope. The sectional drawings explain operation; they do not authorize internal spring/sleeve/washer repair. Later catalog sheets list a cap separately,which must not silently rewrite this1998 supply statement; its later supply context remains distinct.
- Historical TI 41/1998 only: 020 T (series 1129), 026 (1121), FS 550 (4116), BR/SR 320 and 400 (4203). The original scan prints 1129 for 020 T; its extracted body truncates this to 112. Shared later catalog sheets do not extend this TI to 020/020 AV, 024, FS 500/550 L, BR 320 L, MS successors or other models. Availability is historical, not current stock. No hardware operation was performed.
Source: TI 41/1998, p. 1 · TI 41/1998, p. 2 — Full construction,unscaled comparison graph,operation and service-repair restriction.
No additional parts-table entry added.
Service note · 020 T / 026 / FS 550 / BR 320 / BR 400 / SR 320 / SR 400
ElastoStart: rope knots and 4–7 mm end allowance
The grip uses a simple overhand knot; complete rewind-starter work still depends on the model owner manual.
Model-specific manual evidence: 020 T: starter baseline and ElastoStart knot distinction · 026: six clockwise starter turns, not seven · FS 550: seven counterclockwise starter turns
- The TI expressly permits backfitting to its named models. First-time installation needs BOTH the appropriate grip and starter rope; no further changes to the rewind starter mechanism are required. This is not permission to mix rope diameters, omit the rope, or apply the change to every model using an old part number.
- Page2 figure000TI030 KN and all three installation bullets: thread the starter rope through the starter-housing rope-guide bushing FROM OUTSIDE; thread it through the rope rotor and secure it with a simple overhand knot. The TI then says the procedure is as before; it does not supply the full model-specific rotor/spring service sequence.
- Page3 figure000TI031 KN and all seven replacement bullets: ease the cap from the grip; remove the remaining rope from grip and rotor; fit the ElastoStart rope as the standard rope but secure it IN THE GRIP with a SIMPLE overhand knot. Leave rope end a = 4–7 mm (about1/4 in),pull the knot into the grip,and fit the cap until it snaps into position. The procedure is then as before. The tail allowance is not total rope length or spring preload.
- The page3 service note says the owner may maintain the named-model rewind starter using the owner manual,and users must be informed of the changed ElastoStart rope procedure. Later exact020 T,026 and FS550 workshop baselines are reviewed in the linked notes,with different turn counts/directions retained. Exact1998 owner-manual editions,the delegated Standard Repairs/Troubleshooting handbook,and a BR/SR320,400 model-specific baseline remain documented local source gaps. LaterBR/SR340,420 and MS successors are not substitutes.
- Use the model-specific rope set in the source summary. TI41 itself provides no spring preload count,rotor tension check or torque. Values in the linked later-manual notes are explicitly source/edition-bound,not TI specifications or universal ElastoStart settings. No energized or physical procedure was performed.
- Historical TI 41/1998 only: 020 T (series 1129), 026 (1121), FS 550 (4116), BR/SR 320 and 400 (4203). The original scan prints 1129 for 020 T; its extracted body truncates this to 112. Shared later catalog sheets do not extend this TI to 020/020 AV, 024, FS 500/550 L, BR 320 L, MS successors or other models. Availability is historical, not current stock. No hardware operation was performed.
Source: TI 41/1998, p. 1 · TI 41/1998, p. 2 · TI 41/1998, p. 3 — First-installation requirement; complete installation/replacement bullets,figures000TI030/031 KN and owner-manual dependency.
No additional parts-table entry added.
Service note · FS 550
FS 550: seven counterclockwise starter turns
The 2001-09 manual gives the opposite tensioning direction from the reviewed 020 T and 026 manuals.
- Later workshop evidence used to follow the TI41/1998 starter dependency, not proof of the exact owner-manual edition in use in1998. Match the actual model and starter configuration. This is a source-bound service reference, not a complete owner manual. No hardware operation was performed.
- RA_398_00_01_01, cover edition2001-09, printed28–29/PDF29–30. The cover print-production timestamp in2006 and©1998 on contents do not replace the stated edition. SharedFS500/550 manual and wider catalog heading do not extend TI41 toFS500 or FS550L. Introduction preserves dealer-service notice, matching IPL and engineering-change TI requirements.
- The manual distinguishes dirt/pitch from cold-thickened spring lubricant: it describes a few drops of paraffin (kerosene) followed by repeated careful pull/rewind for the latter; dirt/pitch requires removing and cleaning the mechanism, taking special care with the spring. Parts are washed in paraffin or white spirit; rewind spring and starter post use STIHL special lubricant before assembly. This historical treatment is not a universal solvent recommendation.
- Section6.2.1 removes the starter-cover screws and cover; rotor removal is delegated to Standard Repairs, Troubleshooting. Remove the screw and spring pieces. Replacement spring comes in a housing with special lubricant; place bottom upward in the cover and engage the outer loop. The spring may pop out and uncoil. To refit, set the outer-loop offset about20 mm from the housing edge and wind CLOCKWISE from outside inward. Use wooden block1108 893 4800; check the inner loop2 mm from the starter post. Rotor installation remains delegated. Clockwise spring fitting is distinct from counterclockwise tensioning.
- Section6.2.2 makes a rope loop, pushes the rope into the rotor notch and specifies SEVEN full turns COUNTERCLOCKWISE using the rope close to the rotor. Hold the rotor steady, pull out and straighten the rope, hold the grip to keep tension, then release the rotor and slowly let the rope rewind. The grip must seat firmly in the guide bush without drooping; the manual calls for one additional turn if it does not. At full rope extension the rotor must still turn at least another half turn before maximum spring tension. If not, hold the rotor and remove one rope turn. Do not overtension: the rewind spring can break. Refit starter cover and tighten its screws to4.5 Nm (3.3 lbf.ft as printed). This torque is not the starter-cup nut torque or a value supplied by TI41.
- The separate Standard Repairs, Troubleshooting handbook and exact1998 owner-manual edition remain source gaps in the retained local inventory. No BR/SR320,400 preload or rotor procedure is inferred from thisFS550 section, the026 manual or laterBR/SR340,420 sources. Only the TI itself establishes the1998 grip/rope set.
TI dependency: TI 41/1998, p. 1 · TI 41/1998, p. 2 · TI 41/1998, p. 3 — TI41 pages2–3 as-before starter dependency; later model-specific workshop evidence, not specifications printed in the TI.
Later manual evidence: FS 500, 550 workshop manual (2001-09), section Introduction and6.1–6.2.2 (printed28–29), PDF pages 1, 2, 3, 29, 30
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Wrong number or missing part for the FS 500, FS 550, FS 550 L? Report a correction →