Stihl 4116 · Section H · 8 of 16 · 31 parts
Clutch housing, AV system
Fits FS 500, FS 550, FS 550 L.
Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.
Parts (31)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4116 161 0501 | Clutch housing | 1 |
| 2 | 9456 621 3860 | Circlip 35x1.5 | 1 |
| 3 | 9503 003 7450 | Grooved ball bearing 6202-2RS | 1 |
| 4 | 9455 621 1520 | Circlip 15x1 | 1 |
| 5 | 4116 791 2803 | Stop buffer | 1 |
| 6 | 9022 371 1020 | Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 | 4 |
| 7 | 4116 790 9900 | Annular buffer | 2 |
| 8 | 9022 341 1010 | Spline screw IS-M5x18 | 4 |
| 9 | 1125 791 7306 | Plug | 2 |
| 10 | 4116 791 1003 | AV housing, top Fitment / change note → | 1 |
| 11 | 4116 716 2901 | Perforated strip | 1 |
| 12 | 0000 955 0801 | Hexagon nut M8 | 1 |
| 13 | 9451 621 2940 | Shakeproof washer 26x0.5 | 1 |
| 14 | 4116 791 0500 | Cover strip | 1 |
| 15 | 4116 791 2810 | Stop buffer | 1 |
| 16 | 4116 791 2802 | Annular buffer | 2 |
| 17 | 4116 791 7300 | Plug | 2 |
| 18 | 4116 791 1008 | AV housing, bottom Fitment / change note → | 1 |
| 19 | 4116 791 2805 | Stop buffer | 1 |
| 20 | 9022 341 0900 | Spline screw IS-M5x28 | 7 |
| 21 | 4116 791 6805 | Clamp, right | 1 |
| 22 | 4116 791 6804 | Clamp, left | 1 |
| 23 | 9022 341 1350 | Spline screw IS-M6x25 | 1 |
| 24 | 9022 341 0960 | Spline screw IS-M5x12 → replaced by 9022 341 0980 TI 3/2006 | 1 |
| 27 | 4116 700 8400 | Support | 1 |
| 28 | 9416 868 6630 | Hollow rivet 6.5x0.5x6.8 | 2 |
| 29 | 9022 371 1020 | Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 | 2 |
| 30 | 4116 791 2800 | Annular buffer Fitment / change note → | 2 |
| 31 | 4116 791 2801 | Annular buffer Fitment / change note → | 2 |
| 32 | 4116 791 6803 | Clamp, right | 1 |
| 33 | 4116 791 6802 | Clamp, left | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · FS 550
FS 550: mowing and circular-saw handle configurations
Series 4116 introduction describes differences from FS 360/420, not wholesale parts interchange.
- The cover identifies FS 550, series 4116, as the largest model in the contemporary high-performance clearing-saw line. Recommended applications are the same as FS 360 and FS 420. The chapters describe DIFFERENCES over those predecessors, not a complete specification or universal retrofit list.
- The supplied bike handle is designed for circular saw blades; a special bike handle is available for mowing. Both configurations are pictured separately. The multifunction control handle has a soft, non-slip grip surface. No handle dimension or conversion procedure is inferred from the photographs.
- The improved FOUR-POINT antivibration system is claimed to reduce vibration by 20%. This is a historical source claim, not a measured result for an individual machine; no vibration exposure value is supplied.
- The new comfortable FULL HARNESS is OPTIONAL, with its front/rear illustration and description delegated to retained TI22/1997. That accessory bulletin already has separate reviewed design/care and spare-parts notes; optional does not mean included with every FS 550. No new harness part-number equivalence is inferred from the drawing.
- Historical TI44/1997 guidance for the named FS 550 configuration only. Shared IPL sheets do not extend these claims to FS 500, FS 550 L, FS 360 or FS 420. Not current stock, verified physical interchange or a complete operating procedure. No hardware operation was performed.
Source: TI 44/1997, p. 1 · TI 44/1997, p. 2 — Cover, contents and section 1: scope, handles, four-point AV and optional harness.
Referenced bulletin evidence: TI 22/1997, p. 1 · TI 22/1997, p. 2 — Full harness 4134 710 9000: design, release and care.
No additional parts-table entry added.
Conditional replacement · FS 550 / FS 360 / FS 420
FS 550: paired AV buffers and Scandinavia-only option
Use identical buffers in pairs; predecessor AV parts have an explicit serial limit.
- Contrary to the parts-list illustration, buffer 4116 791 2800 is installed at the FRONT of the AV housing. Optional 4116 791 2801 is for SCANDINAVIA ONLY. Always use buffers of IDENTICAL TYPE for repairs and ALWAYS REPLACE IN PAIRS. The printed word annual is a source typo for annular, not a maintenance interval.
- Top housing 23 is 4116 791 1003; buffer 24 has standard 2800 and optional 2801 versions; bottom housing 25 is 4116 791 1008. All carry remark 2: also predecessor FS 360/FS 420 spares FROM machine No. X 37 266 391. Only optional 2801 additionally carries remark 3, Scandinavia only. Preserve X; do not decode a country or invent an upper limit.
- TI 29/1997 is directly referenced and separately reviewed: its predecessor change introduces softer buffers and prohibits mixing original/new AV-housing components; new 2801 buffers require the new housing. TI 44 uses 2800 as the FS 550 default and restricts 2801 geographically. These are distinct model/region contexts, not universal 2800-to 2801 substitution or a reason to erase either statement.
- Historical TI 44/1997 source guidance, not current availability, verified physical interchange or a complete repair procedure. Shared IPL sheets do not extend claims to unnamed variants. No hardware operation was performed.
Source: TI 44/1997, p. 10 — Section7 opening correction, rows23–25 including both24 options, remarks2/3 and TI29 reference.
Referenced bulletin evidence: TI 29/1997, p. 1 — Complete page: introduction, both service prohibitions, drawing, all four summary rows, remarks and footer.
Part numbers (4)
- 4116 791 1003 — Item23 AV housing topPairs/type/region/serial restrictions apply · FS 550; remark2 also FS 360/FS 420 from X 37 266 391; paired identical buffers;2801 Scandinavia only
- 4116 791 2800 — Item24 annular buffer; standardPairs/type/region/serial restrictions apply · FS 550; remark2 also FS 360/FS 420 from X 37 266 391; paired identical buffers;2801 Scandinavia only
- 4116 791 2801 — Item24 annular buffer; Scandinavia onlyPairs/type/region/serial restrictions apply · FS 550; remark2 also FS 360/FS 420 from X 37 266 391; paired identical buffers;2801 Scandinavia only
- 4116 791 1008 — Item25 AV housing bottomPairs/type/region/serial restrictions apply · FS 550; remark2 also FS 360/FS 420 from X 37 266 391; paired identical buffers;2801 Scandinavia only
Wrong number or missing part for the FS 500, FS 550, FS 550 L? Report a correction →