Stihl 4130 · Section P · 13 of 14 · 19 parts
Gear head FS 44
Fits FS 44.
Historical fitment & changes (11) — includes parts and conditions not shown on this drawing.
Change documented in Technical Information 19/1996 — Fuel tank; fan housing; gearhead .
Parts (19)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4130 641 0300 | Gear housing Fitment / change note → | 1 |
| 2 | 4119 713 6500 | Screw plug Fitment / change note → | 1 |
| 3 | 9022 371 1020 | Spline screw IS-M5x20 Fitment / change note → → replaced by 9022 371 1050 TI 30/2004 | 2 |
| 4 | 9456 621 2440 | Circlip 22x1 Fitment / change note → | 1 |
| 5 | 9452 600 0750 | Circlip 9.5x0.8 Fitment / change note → | 1 |
| 6 | 9507 003 8056 | Grooved ball bearing 9.5x22.2x7.14 Fitment / change note → | 1 |
| 7 | 9507 003 8054 | Grooved ball bearing 9.5x22.2x7.14 Fitment / change note → | 2 |
| 8 | 9503 003 5190 | Grooved ball bearing 6001-2RS Fitment / change note → | 1 |
| 9 | 9456 621 3100 | Circlip 28x1.2 Fitment / change note → | 1 |
| 10 | not sold separately | Drive pinion not available as a separate item | 1 |
| 11 | not sold separately | Spur bevel gear not available as a separate item | 1 |
| 12 | 4130 642 0610 | Drive shaft Fitment / change note → | 1 |
| 13 | 4126 710 3800 | Thrust plate Fitment / change note → | 1 |
| 15 | 4126 713 1600 | Thrust washer Fitment / change note → | 1 |
| 16 | 4126 713 3100 | Rider plate | 1 |
| 17 | 4126 642 7600 | Collar nut M10x1 l/h thread Fitment / change note → | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4130 640 0100 | Gearhead Fitment / change note → | 1 |
| — | 4130 640 7300 | Set of pinions Fitment / change note → | 1 |
| — | 0781 120 1117 | Gear lubricant 80 g not illustratedoption | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · FS 44
FS 44: replacement bearing is double-sealed; production bearing remains single-sealed
Gearhead keeps its number; plug gains 13 mm wrench flats alongside its Torx socket.
- Gearhead 4130 640 0100 keeps its number; unmodified version remains supplied until factory stocks are exhausted. Screw plug 4117 713 6501 (drawing 1) changes to 4119 713 6500 (2), with a 13 mm HEX HEAD in addition to the Torx spline socket to ease releasing a tight plug. 13 mm is wrench size, not thread diameter. Original plug is no longer factory-available.
- Output-shaft bearing 9503 003 5190 (item 3) is the replacement for 9503 003 5140. Original bearing CONTINUES on the production line with ONE sealing washer, while the replacement has sealing washers on BOTH sides and can be installed either way round. Do not apply that orientation freedom to the single-sealed production bearing.
- Table says original bearing is no longer available FROM FACTORY as a spare; this is distinct from continued factory production use, not a silently resolved contradiction. No new production cutoff is given. The unattached remark 2 (available for other models) has no marked row in this table and is not assigned arbitrarily.
- Source identifier/header is TI17.94, retained as 1994-17, but the original footer says March 10, 1995 and copyright 1995. Preserve that discrepancy; do not silently change source year or equate publication and review dates.
- Historical TI 17/1994 guidance for the explicitly named models only; no successor or unlisted variant applicability inferred. Factory supply statements are historical, not current stock claims. MOQ columns are order quantities, not fitting quantities. No physical interchange test was performed.
Source: TI 17/1994, p. 5 · TI 17/1994, p. 6 — FS 44: replacement bearing is double-sealed; production bearing remains single-sealed.
Part numbers (5)
- 4130 640 0100 — FS 44 gearheadunchanged number; old version while stocks last · FS 44: replacement bearing is double-sealed; production bearing remains single-sealed
- 4117 713 6501 — Original screw plug, item 1no longer factory-available · FS 44: replacement bearing is double-sealed; production bearing remains single-sealed
- 4119 713 6500 — Hex/Torx screw plug, item 213 mm wrench size · FS 44: replacement bearing is double-sealed; production bearing remains single-sealed
- 9503 003 5140 — Single-sealed output bearingcontinues in production; unavailable as spare · FS 44: replacement bearing is double-sealed; production bearing remains single-sealed
- 9503 003 5190 — Double-sealed replacement output bearing, item 3may be installed either way round · FS 44: replacement bearing is double-sealed; production bearing remains single-sealed
Historical fitment · FS 44
FS 44: splined gearhead changeover and output-speed limits
From X 34 090 160: 1:1.40 and 7000 rpm output, with matching thrust parts.
Later reviewed guidance: FS 44 / 74 / 80 / 85: splined gearhead and matched thrust parts
X 34 090 160 — FS 44 only: from this machine number, gearhead 4130 640 0101 replaces 4130 640 0100 with changed ratio and splined output. Not the tank or later 4137 replacement introduction.
- Original 4130 640 0100: ratio 1:1.33, maximum OUTPUT-shaft speed 7500 rpm, shaft with two flats. New 4130 640 0101: ratio 1:1.40, maximum OUTPUT-shaft speed 7000 rpm, splined shaft/thrust-plate/thrust-washer connection. These are not engine-speed settings.
- From machine X 34 090 160 for FS44. Scan confirms a period after 160; extracted text has spurious K=ft. No K suffix and no FS36/40 serial interval inferred.
- New gearheads supplied ONLY together with new thrust plate and thrust washer to allow replacement on original machines/gearheads. Do not mix the old two-flat plate/washer with the new splined output.
- Original assembly table includes items 1–3,5,7,9–16; modified assembly includes1,2,4,6,8–20. New supplied-package inclusion differs from the old housing/internal assembly. Original complete gearhead while stocks last under remark 1; individual remark 2 spares remain available historically.
- Historical TI19/1996 evidence only; no calendar introduction date or current stock status inferred. FS 44 gearhead changes do not apply to FS 36/40 or FC 44. No hardware operation was performed.
Source: TI 19/1996, p. 1 · TI 19/1996, p. 3 · TI 19/1996, p. 5 — splined gearhead changeover and output-speed limits.
Part numbers (2)
- 4130 640 0100 — Original gearheadTwo-flat output, 1:1.33 · FS44 before stated changeover; historical spare supply
- 4130 640 0101 — Modified gearheadSplined output, 1:1.40 · FS44 from X 34 090 160; matching thrust parts required
Historical fitment · FS 44
FS 44: gear housing, screws and retaining rings
Changed housing and two screw/ring pairs; old remark 2 parts remain spares.
- Table items 1–8: housing 4130 641 0300 becomes 4130 641 0305. Screw plug item 2 remains 4119 713 6500. Two IS-M5x20 screws 9022 371 1020 are replaced in the modified design by two DG5x24 screws 9075 478 4159.
- Retainer ring22x1, 9456 621 2440, changes to24x1.2, 9456 621 2660. Ring9.5x0.8, 9452 600 0750, changes to9.0x1.0, 9455 621 0750. Drawing 342TI011 pairs1,3/4,5/6,7/8 with the table; not all dimensions are interchangeable.
- Original housing, screw and both rings carry remark 2: original versions remain spare parts. Their continued availability does not authorize mixing original and modified internals. No tightening torque supplied. Current IPL automated M5x20→M5x25 cylinder-screw association is not evidence for this gearhead conversion.
- Historical TI19/1996 evidence only; no calendar introduction date or current stock status inferred. FS 44 gearhead changes do not apply to FS 36/40 or FC 44. No hardware operation was performed.
Source: TI 19/1996, p. 1 · TI 19/1996, p. 3 · TI 19/1996, p. 4 · TI 19/1996, p. 5 — gear housing, screws and retaining rings.
Part numbers (9)
- 4130 641 0300 — Gear housingOriginal version; remains spare under remark 2 · FS 44; original versus modified 4130 gearhead
- 4130 641 0305 — Gear housingModified version · FS 44; original versus modified 4130 gearhead
- 4119 713 6500 — Screw plugUnchanged · Both 4130 gearheads
- 9022 371 1020 — Mounting screw, twoOriginal version; remains spare under remark 2 · FS 44; original versus modified 4130 gearhead
- 9075 478 4159 — Mounting screw, twoModified version · FS 44; original versus modified 4130 gearhead
- 9456 621 2440 — Retainer ring, 22x1 versus24x1.2Original version; remains spare under remark 2 · FS 44; original versus modified 4130 gearhead
- 9456 621 2660 — Retainer ring, 22x1 versus24x1.2Modified version · FS 44; original versus modified 4130 gearhead
- 9452 600 0750 — Retainer ring, 9.5x0.8 versus9x1Original version; remains spare under remark 2 · FS 44; original versus modified 4130 gearhead
- 9455 621 0750 — Retainer ring, 9.5x0.8 versus9x1Modified version · FS 44; original versus modified 4130 gearhead
Historical fitment · FS 44
FS 44: bearing changes and unchanged lower bearing
2Z and paired bearings change; 5190 and 28x1.2 ring stay numbered alike.
- Items9–12: grooved ball bearing2Z 9507 003 8056 becomes 9503 003 9853; TWO grooved ball bearings 9507 003 8054 become 9503 003 9850. Both old bearing numbers remain spares under remark 2.
- Lower grooved ball bearing 9503 003 5190 and retainer ring28x1.2 9456 621 3100 are unchanged in the 4130-to-4130 table. Do not swap the 2Z bearing and paired bearings or assume all bearing positions use9853. Later supersession associations do not rewrite this 1996 configuration.
- Historical TI19/1996 evidence only; no calendar introduction date or current stock status inferred. FS 44 gearhead changes do not apply to FS 36/40 or FC 44. No hardware operation was performed.
Source: TI 19/1996, p. 1 · TI 19/1996, p. 3 · TI 19/1996, p. 4 · TI 19/1996, p. 5 — bearing changes and unchanged lower bearing.
Part numbers (6)
- 9507 003 8056 — Grooved ball bearing2Z, item9Original version; remains spare under remark 2 · FS 44; original versus modified 4130 gearhead
- 9503 003 9853 — Grooved ball bearing2Z, item9Modified version · FS 44; original versus modified 4130 gearhead
- 9507 003 8054 — Grooved ball bearing, two, item10Original version; remains spare under remark 2 · FS 44; original versus modified 4130 gearhead
- 9503 003 9850 — Grooved ball bearing, two, item10Modified version · FS 44; original versus modified 4130 gearhead
- 9503 003 5190 — Lower grooved ball bearing, item11Unchanged · Both 4130 gearheads
- 9456 621 3100 — Retainer ring28x1.2, item12Unchanged · Both 4130 gearheads
Historical fitment · FS 44
FS 44: pinion-set and output-shaft changes
Pinions supplied as a set; splined output shaft is not a drop-in component claim.
- Item13 set of pinions 4130 640 7300 becomes 4130 640 7301. Set comprises item 14 drive pinion and item 15 spur bevel gear. Both columns mark these two components with -*- and remark 3: NOT available separately; no individual part numbers invented.
- Item16 output shaft 4130 642 0610 becomes 4130 642 0601, matching the two-flat-to-splined change. Old pinion set and old shaft remain spare parts under remark 2. This lists coordinated design changes, not permission to mix ratios/shafts or swap a single pinion across sets.
- Historical TI19/1996 evidence only; no calendar introduction date or current stock status inferred. FS 44 gearhead changes do not apply to FS 36/40 or FC 44. No hardware operation was performed.
Source: TI 19/1996, p. 1 · TI 19/1996, p. 3 · TI 19/1996, p. 4 · TI 19/1996, p. 5 — pinion-set and output-shaft changes.
Part numbers (4)
- 4130 640 7300 — Set of pinions, includes14/15Original version; remains spare under remark 2 · FS 44; original versus modified 4130 gearhead
- 4130 640 7301 — Set of pinions, includes14/15Modified version · FS 44; original versus modified 4130 gearhead
- 4130 642 0610 — Output shaftOriginal version; remains spare under remark 2 · FS 44; original versus modified 4130 gearhead
- 4130 642 0601 — Output shaftModified version · FS 44; original versus modified 4130 gearhead
Historical fitment · FS 44
FS 44: matching thrust plate, washer and left-hand nut
New plate includes guard washer; old thrust parts remain spares for old design.
- Item17 thrust plate 4126 710 3800 becomes 4130 710 3801, including guard washer item 18. Old guard washer is -*-; new guard washer 4112 717 2801 is numbered. No invented old washer number or remark 3 assignment to that old washer.
- Item19 thrust washer 4126 713 1600 becomes 4130 713 1600. Item20 collar nut remains 4126 642 7600, M10x1 LEFT-HAND thread. Old plate and thrust washer remain spares under remark 2; retain two-flat/splined pairing.
- Current exact-model sheet shows the original gearhead and thrust parts; generic FS sheet has later plate4137 710 3800. Do not silently replace the historical4130 710 3801 or broaden this FS44 note to every generic FS model. No nut torque stated.
- Historical TI19/1996 evidence only; no calendar introduction date or current stock status inferred. FS 44 gearhead changes do not apply to FS 36/40 or FC 44. No hardware operation was performed.
Source: TI 19/1996, p. 1 · TI 19/1996, p. 3 · TI 19/1996, p. 4 · TI 19/1996, p. 5 — matching thrust plate, washer and left-hand nut.
Part numbers (6)
- 4126 710 3800 — Thrust plate, includes guard washerOriginal version; remains spare under remark 2 · FS 44; original versus modified 4130 gearhead
- 4130 710 3801 — Thrust plate, includes guard washerModified version · FS 44; original versus modified 4130 gearhead
- 4112 717 2801 — Guard washerNew numbered item18 · Modified thrust plate
- 4126 713 1600 — Thrust washerOriginal version; remains spare under remark 2 · FS 44; original versus modified 4130 gearhead
- 4130 713 1600 — Thrust washerModified version · FS 44; original versus modified 4130 gearhead
- 4126 642 7600 — Collar nut M10x1 left-handUnchanged · Both designs; matching shaft and thrust parts
Historical fitment · FS 44
FS 44: later replacement gearhead and locating O-ring
4137 640 0100 replaces 4130 640 0101 in spares; no serial cutoff supplied.
Later reviewed guidance: FS 44: announced locating O-ring was never introduced
- Section2.2 standardizes replacement FS44 gearhead to4137 640 0100, previously4130 640 0101. New models are unnamed, so their identities/application are not inferred. This later replacement has NO stated serial cutoff; X34 090 160 belongs to section 2.1 only.
- Text calls the lower output-shaft bearing the only difference, uprated for higher-power new units, then separately describes added O-ring retention. Table item 21 prints SAME bearing9503 003 5190 in old and new columns; text says this high-grade spare serves both gearheads and was also used in original4130 640 0100. Preserve the unchanged number versus changed bearing description without inventing a different production bearing number.
- O-ring A10x1.5, 9645 945 7509, item 22 locates the thrust plate and prevents it slipping off the output shaft; drawing342TI010 points to its location. Not an oil-seal claim. It is also to be fitted to FS44 standard gearheads in future, but no introduction serial/date is stated.
- 4137 replacement includes items 21/22; all other parts as4130 640 0101 under2.1. Old4130 640 0101 factory stock while supplies last (remark 1); introduction in progress. Footer cites previous TI07/1996 as context, not a supersession of this serial statement.
- Historical TI19/1996 evidence only; no calendar introduction date or current stock status inferred. FS 44 gearhead changes do not apply to FS 36/40 or FC 44. No hardware operation was performed.
Source: TI 19/1996, p. 1 · TI 19/1996, p. 4 · TI 19/1996, p. 5 — later replacement gearhead and locating O-ring.
Part numbers (4)
- 4130 640 0101 — GearheadPrevious replacement; while stocks last · FS44
- 4137 640 0100 — Standardized replacement gearheadNew service replacement · FS44; no new-unit model inference
- 9503 003 5190 — Lower ball bearingSame printed spare number despite uprated description · Both replacement gearheads; also original0100
- 9645 945 7509 — O-ring A10x1.5Thrust-plate locating ring · New replacement; future FS44 standard gearhead
Service note · FS 44 / FS 74 / FS 80 / FS 85
FS 44 / 74 / 80 / 85: splined gearhead and matched thrust parts
FS 80/85 change at X 35 221 994; replacement supply includes the matching plate and washer.
X 35 221 994 — FS80 and FS85 production change only; FS74 in progress; FS44 replacement scope, not this serial cutoff.
- New gearhead replaces the original on FS 80 and FS 85 from X 35 221 994 to improve transmission of power. It is also a replacement for FS 44 and FS 74. The serial cutoff belongs ONLY to FS 80/85; FS 74 introduction is in progress. No extension to shared-sheet FS 36/40, FS 72/76, FS 75 or R/T/RX variants.
- Page1 comparison: old4130 640 0100 is 1:1.33 / 7900 rpm, two flats; new4137 640 0100 is 1:1.40 / 7500 rpm, splined. These are rated maximum OUTPUT-SHAFT speeds, NOT engine tuning settings. Drawing342TI009 GM contrasts the old two-flat connection on the left with splined shaft, plate and washer on the right.
- TI19/1996 page3, specifically for FS 44, instead prints7500 rpm for old4130 640 0100 and7000 rpm for new4130 640 0101. Preserve that source/model/assembly context and the differing figures; TI32 does not explicitly revoke the earlier FS 44 speed or authorize raising it. Do not collapse the two tables into one universal limit.
- New gearheads supplied ONLY TOGETHER WITH new thrust plate14 and thrust washer16. Plate14 includes protective washer15. Original plate4126 710 3800 and washer4126 713 1600 remain spares (remark2); old protective washer has no number and is not a spare (remark4). New protective washer4112 717 2801 is separately numbered. No mixed two-flat/splined assembly authorized.
- Old gearhead table includes1,2,4,6,8–16; new includes1,3,5,7–16. Old complete4130 640 0100 supplied only until factory stocks exhausted (remark1). All other parts as before; the table is not a complete independent IPL. Later FS74 and FS80/85 sheets retain4137 gearhead but list thrust plate4137 710 3800 rather than source4130 710 3801; no silent replacement of historical numbers or proof of supersession.
- Historical source guidance and factory supply, not current availability or verified physical interchange. No hardware operation was performed.
Source: TI 32/1997, p. 1 · TI 32/1997, p. 2 · TI 32/1997, p. 3 — Sections1.1,1.3,1.4 and1.6 gearhead/thrust rows, drawing and supply.
Referenced bulletin evidence: TI 19/1996, p. 3 · TI 19/1996, p. 5 — Earlier FS44-specific speed comparison and assembly table.
Part numbers (7)
- 4130 640 0100 — Original gearhead, two-flat outputStock exhaustion · Only the exact model/configuration and restrictions of 1997-32
- 4137 640 0100 — New gearhead, splined outputSupplied with new thrust plate and washer · Only the exact model/configuration and restrictions of 1997-32
- 4126 710 3800 — Original thrust plate including protective washerRemains spare · Only the exact model/configuration and restrictions of 1997-32
- 4130 710 3801 — New thrust plate including item15Item14 · Only the exact model/configuration and restrictions of 1997-32
- 4112 717 2801 — New protective washerItem15; original not a spare · Only the exact model/configuration and restrictions of 1997-32
- 4126 713 1600 — Original thrust washerRemains spare · Only the exact model/configuration and restrictions of 1997-32
- 4130 713 1600 — New thrust washerItem16 · Only the exact model/configuration and restrictions of 1997-32
Service note · FS 44 / FS 74 / FS 80 / FS 85
FS 44 / 74 / 80 / 85: gear housing, retaining rings and DG screw torque
Only new gearhead 4137 640 0100 DG screws take 8.5 Nm (6.3 lbf.ft).
- Section1.5 specifies8.5 Nm (6.3 lbf.ft) ONLY for the DG screws, item3, in NEW gearhead4137 640 0100. This is not a torque for original IS-M5x20 screws or every fastener on these models. No torque inferred for a4130 640 0101 assembly.
- Items1–7: housing0300→0305; two9022 371 1020 IS-M5x20 screws replaced by two9075 478 4159 DG5x24 screws; ring22x1→24x1.2 and ring9.5x0.8→9.0x1.0. All original housing/screw/ring rows carry remark2, original remains spare. Continued spare supply does not authorize arbitrary mixing.
- Drawing393TI004 GM explicitly pairs screws2/3 and rings4/5,6/7. TI callouts are not current IPL positions. Lower shaft bearing, screw plug and collar nut are drawn without numbers in this abbreviated summary; no new number or deletion inferred. Model production/replacement scope follows section1.1, not the other models sharing an IPL sheet.
- Historical source guidance and factory supply, not current availability or verified physical interchange. No hardware operation was performed.
Source: TI 32/1997, p. 1 · TI 32/1997, p. 2 · TI 32/1997, p. 3 — Sections1.5 and1.6: torque, all housing/screw/ring rows and drawing.
Part numbers (8)
- 4130 641 0300 — Original gear housingRemains spare · Only the exact model/configuration and restrictions of 1997-32
- 4130 641 0305 — New gear housingItem1 · Only the exact model/configuration and restrictions of 1997-32
- 9022 371 1020 — Original IS-M5x20 spline screw, twoItem2; remains spare · Only the exact model/configuration and restrictions of 1997-32
- 9075 478 4159 — New DG5x24 spline screw, twoItem3; 8.5 Nm · Only the exact model/configuration and restrictions of 1997-32
- 9456 621 2440 — Original retainer ring22x1Item4; remains spare · Only the exact model/configuration and restrictions of 1997-32
- 9456 621 2660 — New retainer ring24x1.2Item5 · Only the exact model/configuration and restrictions of 1997-32
- 9452 600 0750 — Original retainer ring9.5x0.8Item6; remains spare · Only the exact model/configuration and restrictions of 1997-32
- 9455 621 0750 — New retainer ring9.0x1.0Item7 · Only the exact model/configuration and restrictions of 1997-32
Service note · FS 44 / FS 74 / FS 80 / FS 85
FS 44 / 74 / 80 / 85: coordinated bearings, pinion set and shaft
Two bearing positions change; pinions remain a set, not separate spare items.
- Bearing2Z item8:9507 003 8056→9503 003 9853. TWO item9 bearings:9507 003 8054→9503 003 9850. Do not merge these bearing positions or assume all use9853. Old bearing rows remain spares under remark2.
- Item10 pinion set4130 640 7300→4130 640 7301 consists of drive pinion11 and spur bevel gear12. Both individual rows have -*- and remark3: NOT AVAILABLE AS SEPARATE ITEMS. Drawing places10/11 on the input side and10/12 on the output side; these are two members of one set, not two different set numbers.
- Item13 output shaft4130 642 0610→4130 642 0601 accompanies the two-flat-to-splined change. Old shaft and old pinion set remain spares (remark2). These coordinated changes are not approval to mix individual pinions, ratios, shafts or bearings across designs. The serial/model restrictions are those of section1.1.
- Historical source guidance and factory supply, not current availability or verified physical interchange. No hardware operation was performed.
Source: TI 32/1997, p. 1 · TI 32/1997, p. 2 · TI 32/1997, p. 3 — Section1.6 items8–13, drawing, quantities and supply.
Part numbers (8)
- 9507 003 8056 — Original grooved ball bearing2ZItem8; remains spare · Only the exact model/configuration and restrictions of 1997-32
- 9503 003 9853 — New grooved ball bearing2ZItem8 · Only the exact model/configuration and restrictions of 1997-32
- 9507 003 8054 — Original grooved ball bearing, twoItem9; remains spare · Only the exact model/configuration and restrictions of 1997-32
- 9503 003 9850 — New grooved ball bearing, twoItem9 · Only the exact model/configuration and restrictions of 1997-32
- 4130 640 7300 — Original set of pinionsItem10; remains spare · Only the exact model/configuration and restrictions of 1997-32
- 4130 640 7301 — New set of pinionsItem10; includes11/12 · Only the exact model/configuration and restrictions of 1997-32
- 4130 642 0610 — Original output shaftItem13; remains spare · Only the exact model/configuration and restrictions of 1997-32
- 4130 642 0601 — New output shaftItem13; splined · Only the exact model/configuration and restrictions of 1997-32
Service note · FS 44
FS 44: announced locating O-ring was never introduced
TI32 corrects TI19/1996: 9645 945 7509 is deleted from this gearhead parts list.
- Section1.2 explicitly says the O-ring announced in TI19/1996 chapter2.2 item22 WAS NOT INTRODUCED and has been DELETED FROM THE PARTS LIST. The earlier announcement is historical evidence, not proof of physical production installation or a retrofit instruction.
- TI32 page3 See1.2 FS44 shows gearhead4137 640 0100 unchanged; item17 old O-ring9645 945 7509, new dashed. The same row carries remark2, ORIGINAL VERSION REMAINS AVAILABLE AS SPARE. Retain this tension with the explicit non-introduction/deletion statement: spare-number availability is not evidence the ring was ever introduced in this FS44 assembly.
- Drawing393TI004 GM on page2 STILL depicts a ring labeled17 between thrust plate14/15 and thrust washer16. It illustrates the deleted ring; it does not override the prose and dashed new row. Introduction under1.2 says in progress, not an installed-ring production cutoff. No serial or date invented.
- TI19/1996 page4 says the ring locates the plate and will also be fitted to standard FS44 gearheads; page5 item22 lists it in the new4137 assembly. Both original pages remain linked and the old note exposes this later correction. TI32 footer references19.96/07.96/36.96 are bibliography, not delegated repair procedures. No additional source dependency is needed to retain the contradiction.
- Historical source guidance and factory supply, not current availability or verified physical interchange. No hardware operation was performed.
Source: TI 32/1997, p. 1 · TI 32/1997, p. 2 · TI 32/1997, p. 3 — Section1.2 correction, page2 retained ring drawing, page3 FS44 row and remark2.
Referenced bulletin evidence: TI 19/1996, p. 4 · TI 19/1996, p. 5 — Original locating-ring announcement, diagram and item22.
Part numbers (2)
- 4137 640 0100 — FS44 replacement gearheadSame assembly number · Only the exact model/configuration and restrictions of 1997-32
- 9645 945 7509 — O-ring A10x1.5Not introduced; deleted from this application · Only the exact model/configuration and restrictions of 1997-32
Wrong number or missing part for the FS 44? Report a correction →