Stihl 4134 · Section F · 6 of 12 · 39 parts
Carburetor C1Q-S51C, C1Q-S36G
Fits BT 120 C.
Historical fitment & changes (4) — includes parts and conditions not shown on this drawing.
Parts (39)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4116 121 5100 | Inlet needle | 1 |
| 2 | 1120 122 3004 | Spring | 1 |
| 3 | 1120 121 9200 | Spindle | 1 |
| 4 | 1125 121 5000 | Inlet control lever | 1 |
| 5 | 1120 122 6600 | Collar screw | 1 |
| 6 | 4137 122 5100 | Outlet valve | 1 |
| 7 | 1130 121 5601 | Fixed jet 0.44 | 1 |
| 8 | 4119 121 0700 | Cup plug | 1 |
| 9 | 4129 121 0700 | Cup plug | 1 |
| 10 | 4129 129 0902 | Gasket | 1 |
| 11 | 4129 121 4700 | Metering diaphragm | 1 |
| 12 | 4134 121 0801 | End cover → replaced by 4134 121 0803, 4134 121 0803 TI 6/2009 | 1 |
| 13 | 1120 122 6601 | Collar screw | 4 |
| 14 | 1130 122 6300 | Idle speed adjustment screw Fitment / change note → | 1 |
| 15 | 1123 122 3000 | Spring | 1 |
| 16 | 4134 120 7100 NLA | Throttle shaft with lever | 1 |
| 17 | 4134 123 7300 | Lever | 1 |
| 18 | 4134 122 5000 | Spacer sleeve | 1 |
| 19 | 4128 121 8900 | Pin | 1 |
| 20 | 4137 121 8600 | Washer | 1 |
| 21 | 1120 122 9000 | E-clip | 1 |
| 22 | 9079 319 0280 | Flat head screw M3x3.5 | 1 |
| 23 | 1123 121 3300 NLA | Throttle shutter Fitment / change note → → replaced by 4134 121 3300 TI 9/2003 | 1 |
| 24 | 1120 122 7400 | Round head screw | 1 |
| 25 | 1123 121 7800 | Strainer | 1 |
| 26 | 1129 121 4800 | Pump diaphragm | 1 |
| 27 | 1123 129 0905 | Gasket | 1 |
| 28 | 4128 121 0800 | End cover → replaced by 1130 121 0801 TI 31/2009 | 1 |
| 29 | 1120 122 7800 | Oval head screw | 1 |
| 30 | 4119 122 3002 | Spring | 1 |
| 31 | 4119 122 4200 | Ball | 1 |
| 32 | 4134 121 3000 | Choke shaft | 1 |
| 33 | 4128 121 2900 | Choke shutter | 1 |
| 34 | 1125 122 7403 | Round head screw | 1 |
| 35 | 4134 121 5402 NLA | Valve jet | 1 |
| 36 | 4128 122 6300 NLA | Idle speed adjustment screw Fitment / change note → | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4134 120 0651 NLA | Carburetor C1Q-S51C Fitment / change note → | 1 |
| — | not sold separately | Carburetor C1Q-S36G no longer available from factory | 1 |
| — | 4134 007 1060 | Set of carburetor parts | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Conditional replacement · BT 120 C / FS 120 / FS 200 / FS 250 / FS 350
TI09: C1Q-S51 throttle shutter changes in two stages
The later shutter adds idle airflow; the two replacements are not one undifferentiated change.
- First stage: throttle shutter 1123 121 3300 was replaced by 4134 121 3300. Second stage: 4134 121 3300 was replaced by 4134 121 3301, which has a hole allowing additional air to flow at idle.
- The modified parts can be fitted to older C1Q-S51 carburetors. The summary associates the first shutter change with C1Q-S51B to C1Q-S51C and the later shutter plus idle screw with C1Q-S51C to C1Q-S51D. It does not give a hole diameter or permission to drill an older shutter.
- Remark2 says the previous shutters remain available. Introduction is in progress; no serial cutoff or exact introduction date is supplied. Historical factory availability is not current stock verification.
- Only the C1Q-S51 configurations of the printed BT 120 C, FS 120, FS 200, FS 250 and FS 350 models are covered. Shared C1Q-S36G/FS 300/R-variant sheets do not establish those carburetor or model applications. This is not a C1Q-S82/S83 conversion instruction. No physical interchange test was performed.
Source: TI 9/2003, p. 1 · TI 9/2003, p. 18 — 3.1 and3.3 throttle shutters and summary.
Part numbers (3)
- 1123 121 3300 — Original throttle shutterFirst-stage predecessor · Listed TI09 models with C1Q-S51 only
- 4134 121 3300 — Intermediate throttle shutterFirst replacement; second-stage predecessor · Listed TI09 models with C1Q-S51 only
- 4134 121 3301 — Later throttle shutter with idle-air holeSecond replacement · Listed TI09 models with C1Q-S51 only
Conditional replacement · BT 120 C / FS 120 / FS 200 / FS 250 / FS 350
TI09: longer C1Q-S51 idle screw and supply conflict
The LD screw changes from 16.6 to 16.9 mm; prose and table disagree on old-part availability.
- Idle speed adjustment screw LD 4134 122 6300 is replaced by slightly longer 1130 122 6300 to optimize adjustment range. Diagram250TI032 marks old dimension a = 16.6 mm (0.654 in) and new dimension b = 16.9 mm (0.665 in). These are the labeled diagram dimensions, not invented thread sizes or tuning settings.
- Section3 permits the modified parts in older C1Q-S51 carburetors. Row6 groups the new screw with the later shutter in the C1Q-S51D stage; the order number alone does not identify an assembled carburetor revision.
- Unresolved source conflict: section3.2 says the previous idle screw will be discontinued, while summary row6 carries remark2, previous version of part remains available. Preserve both statements; no chronology is invented to reconcile them, and neither proves current availability.
- Introduction is in progress. No adjustment turns, idle RPM, production serial or substitute screw is specified in section3.
- Only the C1Q-S51 configurations of the printed BT 120 C, FS 120, FS 200, FS 250 and FS 350 models are covered. Shared C1Q-S36G/FS 300/R-variant sheets do not establish those carburetor or model applications. This is not a C1Q-S82/S83 conversion instruction. No physical interchange test was performed.
Source: TI 9/2003, p. 1 · TI 9/2003, p. 18 — 3.2 LD screw diagram250TI032 and3.3 summary row6/remark2.
Part numbers (2)
- 4134 122 6300 — Previous LD idle speed adjustment screw16.6 mm diagram dimension; supply conflict retained · Listed TI09 models with C1Q-S51 only
- 1130 122 6300 — New LD idle speed adjustment screw16.9 mm diagram dimension; C1Q-S51 retrofit · Listed TI09 models with C1Q-S51 only
Conditional replacement · BT 120 C / FS 120 / FS 200 / FS 250 / FS 350
TI09: C1Q-S51B, C and D share one order number
4134 120 0651 does not identify which shutter and idle screw a carburetor contains.
- C1Q-S51B, C1Q-S51C and C1Q-S51D all carry order number 4134 120 0651 in the summary. The first stage B to C changes shutter 1123 121 3300 to 4134 121 3300. The later C to D stage changes the shutter to 4134 121 3301 and the LD screw to 1130 122 6300. All other parts are as before within this section.
- Remark1 is printed on the C1Q-S51C rows2 and4: the previous version is supplied only while factory stocks last, then item5 (C1Q-S51D) is supplied. Do not silently attach that remark to the unmarked B row or interpret the unchanged order number as unchanged contents.
- Remark2 on the previous shutters and screw says they remain available; the screw prose contradicts that remark and is retained separately. These are historical supply statements, not an inventory promise. Introduction in progress supplies no numeric serial limit.
- Only the C1Q-S51 configurations of the printed BT 120 C, FS 120, FS 200, FS 250 and FS 350 models are covered. Shared C1Q-S36G/FS 300/R-variant sheets do not establish those carburetor or model applications. This is not a C1Q-S82/S83 conversion instruction. No physical interchange test was performed.
Source: TI 9/2003, p. 1 · TI 9/2003, p. 18 — 3.3 complete summary and remarks.
Part numbers (6)
- 4134 120 0651 — C1Q-S51B / C / D carburetor assemblySame number across revised contents · Listed TI09 models with C1Q-S51 only
- 1123 121 3300 — B-stage shutterOriginal · Listed TI09 models with C1Q-S51 only
- 4134 121 3300 — C-stage shutterIntermediate · Listed TI09 models with C1Q-S51 only
- 4134 121 3301 — D-stage shutterWith idle-air hole · Listed TI09 models with C1Q-S51 only
- 4134 122 6300 — Previous LD screwAvailability conflict · Listed TI09 models with C1Q-S51 only
- 1130 122 6300 — D-stage LD screwLonger replacement · Listed TI09 models with C1Q-S51 only
Conditional replacement · FS 120 / FS 200 / FS 350 / BT 120 C
TI22: C1Q-S51A/B share a number but use different idle screws
The original screw remains for older carburetors; printed metric and inch dimensions disagree.
- C1Q-S51A becomes C1Q-S51B when idle screw 4128 122 6300 changes to 4134 122 6300 to improve acceleration and idle. Both carburetor versions use 4134 120 0651; all other parts remain as before. Introduction is in progress, with no serial.
- Previous screw 4128 122 6300 remains available for previous carburetors. The illustration labels old span a as 17.3 mm (0.681 inch) and new span b as 16.9 mm (0.655 inch). The new printed units are inconsistent: 16.9 mm is about 0.665 inch, not 0.655. Both original values are retained; do not silently select a corrected manufacturing dimension.
- This is the earlier A-to-B change, not the later S51C idle-screw availability conflict in TI09/2003. No chronology resolving that later contradiction is inferred.
- TI22 describes an interdependent update package. Its introduction says most new parts were fitted to FS 250 from production start, with unspecified exceptions; this is not blanket FS 250 fitment approval. Shared sheets do not extend the named model/configuration scope. Factory availability is historical, not current stock. No physical interchange test was performed.
Source: TI 22/2001, p. 4 — 4 entire drawing, dimensions, prose and summary.
Part numbers (3)
- 4134 120 0651 — C1Q-S51A / C1Q-S51B carburetorSame number; version matters · FS 120, FS 200, FS 350, BT 120 C; stated configuration only
- 4128 122 6300 — Previous idle speed screwRetained for previous carburetors · FS 120, FS 200, FS 350, BT 120 C; stated configuration only
- 4134 122 6300 — New idle speed screwS51B revision · FS 120, FS 200, FS 350, BT 120 C; stated configuration only
Wrong number or missing part for the BT 120 C? Report a correction →