Stihl 4134 · Section G · 7 of 18 · 48 parts
Carburetor C1Q-S161, -S162, -S163, -S164, -S82, -S83, -S138, -S139
Fits FS 120, FS 120 R, FS 200, FS 200 R, FS 250, FS 250 R.
Historical fitment & changes (8) — includes parts and conditions not shown on this drawing.
Parts (48)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4134 120 7101 | Throttle shaft with lever | 1 |
| 2 | 1123 122 3000 | Spring | 1 |
| 3 | 4128 121 8901 | Pin Fitment / change note → | 1 |
| 4 | 4137 121 8600 | Washer | 1 |
| 5 | 1120 122 9000 | E-clip | 1 |
| 6 | 4134 123 7300 | Lever | 1 |
| 7 | 9079 319 0280 | Flat head screw M3x3.5 | 1 |
| 8 | 1120 122 9000 | E-clip | 1 |
| 9 | 4134 121 3000 | Choke shaft | 1 |
| 10 | 1129 121 4800 | Pump diaphragm | 1 |
| 11 | 1123 129 0905 | Gasket | 1 |
| 12 | 4134 121 0802 | End cover | 1 |
| 13 | 1120 122 7800 | Oval head screw | 1 |
| 14 | 4116 121 5100 | Inlet needle | 1 |
| 15 | 1123 122 3001 | Spring | 1 |
| 16 | 1125 121 5000 | Inlet control lever | 1 |
| 17 | 1120 121 9200 | Spindle | 1 |
| 18 | 1120 122 6600 | Collar screw | 1 |
| 20 | 4134 121 4700 | Metering diaphragm | 1 |
| 21 | 4134 121 0803 | End cover | 1 |
| 22 | 1129 129 0900 | Gasket → replaced by 4134 121 4700 TI 16/2009 | 1 |
| 23 | 4129 121 4700 | Metering diaphragm | 1 |
| 24 | 4134 121 0801 | End cover → replaced by 4134 121 0803, 4134 121 0803 TI 6/2009 | 1 |
| 25 | 1120 122 6601 | Collar screw | 4 |
| 26 | 4134 122 6701 | High speed adjustment screw | 1 |
| 27 | 4134 122 6801 | Low speed adjustment screw | 1 |
| 28 | 4134 122 6802 | Low speed adjustment screw | 1 |
| 29 | 1123 121 7800 | Strainer | 1 |
| 30 | 4180 122 6200 | Idle speed adjustment screw | 1 |
| 31 | 1120 122 7400 | Round head screw | 1 |
| 32 | 4134 121 3302 | Throttle shutter | 1 |
| 33 | 1125 122 4200 | Clamp | 1 |
| 34 | 4119 122 3002 | Spring | 1 |
| 35 | 4119 122 4200 | Ball | 1 |
| 36 | 4128 121 2900 | Choke shutter | 1 |
| 37 | 1125 122 7403 | Round head screw | 1 |
| 38 | 4229 121 2701 | Cap | 1 |
| 39 | 1132 121 5640 | Fixed jet 0.40 | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4134 120 0652 | Carburetor C1Q-S161 | 1 |
| — | 4134 120 0654 | Carburetor C1Q-S163 | 1 |
| — | 4134 120 0653 | Carburetor C1Q-S162 | 1 |
| — | 4134 120 0655 | Carburetor C1Q-S164 | 1 |
| — | 4134 120 0603 | Carburetor C1Q-S82 Fitment / change note → no longer available from factory | 1 |
| — | 4134 120 0605 | Carburetor C1Q-S138 no longer available from factory | 1 |
| — | 4134 120 0604 | Carburetor C1Q-S83 Fitment / change note → no longer available from factory | 1 |
| — | 4134 120 0606 | Carburetor C1Q-S139 no longer available from factory | 1 |
| — | 4128 007 1060 | Set of carburetor parts | 1 |
| — | 1129 007 1062 | Set of carburetor parts Fitment / change note → → replaced by 4128 007 1060, 4128 007 1060 TI 6/2009 | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Conditional replacement · FS 120
TI 09: FS 120 C1Q-S82 and matched shroud
The carburetor and shroud pair is model-specific; the old shared number does not make the new assemblies universal.
- Summary assigns old C1Q-S51C carburetor 4134 120 0651 to new C1Q-S82 4134 120 0603 for FS 120, with shroud 4134 080 1600 replaced by 4134 084 0911. Do not transfer this pair to another model merely because the old carburetor or shroud number was shared.
- This is the change from BIS (Balanced Idle System), with one LD adjusting screw, to separate H, L and LA screws. The H cap allows only 270 degrees (3/4 turn) when permanently attached; the caps have internal screwdriver guide funnels.
- Older-machine conversion also requires the appropriate throttle cable pin, new shroud and the specified nameplate; guide grommet may be removed. The page 16 pin directions/model wording remain ambiguous and prior-TI conversion dependencies remain open. This note is not a complete retrofit authorization.
- Summary remark1 retains the previous carburetor and shroud for older machines; remark2 points to the machine parts list for new carburetor parts. Historical availability is not current stock. Introduction refers to 1.10: USA production in progress, not a global date or numeric serial cutoff.
- Applies only to the listed TI 09 models with the stated C1Q-S82/S83 configuration. Shared sheets do not extend this evidence to FS 300, BT 121, R variants or later S161/S162/S163/S164/S138/S139 carburetors. No physical interchange test was performed.
Source: TI 9/2003, p. 7 · TI 9/2003, p. 12 · TI 9/2003, p. 16 · TI 9/2003, p. 17 — 2.1–2.5 model-specific summary;1.10 introduction.
Part numbers (4)
- 4134 120 0651 — Previous C1Q-S51C carburetorHistorical predecessor · FS 120; TI 09 section 2 configuration only
- 4134 120 0603 — C1Q-S82 carburetorModel-specific replacement · BT 120 C and FS 120; C1Q-S82 only
- 4134 080 1600 — Previous shroudRetained for older machines · FS 120; TI 09 section 2 configuration only
- 4134 084 0911 — New shroudRequired matching model-specific version · FS 120; TI 09 section 2 configuration only
Conditional replacement · FS 200 / FS 250
TI 09: FS 200, FS 250 C1Q-S83 and matched shroud
The carburetor and shroud pair is model-specific; the old shared number does not make the new assemblies universal.
- Summary assigns old C1Q-S51C carburetor 4134 120 0651 to new C1Q-S83 4134 120 0604 for FS 200, FS 250, with shroud 4134 080 1600 replaced by 4134 084 0911. Do not transfer this pair to another model merely because the old carburetor or shroud number was shared.
- This is the change from BIS (Balanced Idle System), with one LD adjusting screw, to separate H, L and LA screws. The H cap allows only 270 degrees (3/4 turn) when permanently attached; the caps have internal screwdriver guide funnels.
- Older-machine conversion also requires the appropriate throttle cable pin, new shroud and the specified nameplate; guide grommet may be removed. The page 16 pin directions/model wording remain ambiguous and prior-TI conversion dependencies remain open. This note is not a complete retrofit authorization.
- Summary remark1 retains the previous carburetor and shroud for older machines; remark2 points to the machine parts list for new carburetor parts. Historical availability is not current stock. Introduction refers to 1.10: USA production in progress, not a global date or numeric serial cutoff.
- Applies only to the listed TI 09 models with the stated C1Q-S82/S83 configuration. Shared sheets do not extend this evidence to FS 300, BT 121, R variants or later S161/S162/S163/S164/S138/S139 carburetors. No physical interchange test was performed.
Source: TI 9/2003, p. 7 · TI 9/2003, p. 12 · TI 9/2003, p. 16 · TI 9/2003, p. 17 — 2.1–2.5 model-specific summary;1.10 introduction.
Part numbers (4)
- 4134 120 0651 — Previous C1Q-S51C carburetorHistorical predecessor · FS 200, FS 250; TI 09 section 2 configuration only
- 4134 120 0604 — C1Q-S83 carburetorModel-specific replacement · FS 200, FS 250 and FS 350; C1Q-S83 only
- 4134 080 1600 — Previous shroudRetained for older machines · FS 200, FS 250; TI 09 section 2 configuration only
- 4134 084 0911 — New shroudRequired matching model-specific version · FS 200, FS 250; TI 09 section 2 configuration only
Service note · BT 120 C / FS 120 / FS 200 / FS 250 / FS 350
TI 09: C1Q-S82/S83 cap removal and cap-off basic setting
Service adjustment uses H 1¾ and L 1 turn; fit a NEW cap at the rich stop with 1 mm clearance.
- Diagram 256TI023 identifies low-speed screw1, high-speed screw2, H cap3, idle-speed screw4 and cap-travel stop5. The permanently fitted H cap restricts travel to 270 degrees (3/4 turn); this range is not the cap-off basic setting.
- For adjusting-screw replacement or carburetor cleaning, a Service Technician removes the H cap with extractor 5910 890 4501 between cap and carburetor housing and pries it off. If it binds, rotate the extractor so the closed side of its U-shaped blade is opposite the housing, slide it under the cap and pry the cap off fully. Caps must not be reused.
- After maintenance, check/clean or replace the air filter and muffler/spark-arresting screen as necessary, inspect/replace fuel filter, and check/adjust throttle cable per 1.12.5. Service engineer basic setting WITHOUT H cap: carefully turn H and L all the way in, then back H off 1 3/4 turn and L 1 turn.
- Fit a NEW cap facing the rich stop shown by diagram 256TI026 and press until it engages in position 2. Do not press it fully against the carburetor housing: diagram 256TI027 requires distance a = 1 mm to avoid damage. No cap part number, pressing tool or invented alternate position is supplied.
- Page 13 prints references 1.1.4 and 1.1.5, but the matching titled basic/standard-setting sections actually present are 2.1.4 and 2.1.5. Preserve that numbering error. Follow with capped user adjustment if necessary; do not confuse H 1 3/4 cap-off turns with the capped3/4-turn travel.
- Applies only to the listed TI 09 models with the stated C1Q-S82/S83 configuration. Shared sheets do not extend this evidence to FS 300, BT 121, R variants or later S161/S162/S163/S164/S138/S139 carburetors. No physical interchange test was performed.
Source: TI 9/2003, p. 12 · TI 9/2003, p. 13 · TI 9/2003, p. 14 · TI 9/2003, p. 17 — 2.1.1–2.1.4 mechanical design, cap removal, basic setting and cap installation.
Part numbers (3)
- 5910 890 4501 — H limiter cap extractorService removal; caps not reusable · BT 120 C, FS 120, FS 200, FS 250, FS 350; TI 09 section 2 configuration only
- 4134 120 0603 — C1Q-S82 carburetorBT 120C and FS 120 only · BT 120 C and FS 120; C1Q-S82 only
- 4134 120 0604 — C1Q-S83 carburetorFS 200/250/350 only · FS 200, FS 250 and FS 350; C1Q-S83 only
Service note · BT 120 C / FS 120 / FS 200 / FS 250 / FS 350
TI 09: C1Q-S82/S83 service idle speed and mixture symptoms
LA target 2800±200 rpm; lean and rich symptoms require opposite L-screw directions.
- Use idle-speed screw LA to set 2800 rpm with tolerance +/-200 rpm, aided by a tachometer. This is the new C1Q-S82/S83 section, not an LD setting for C1Q-S51.
- Varying idle speed, poor acceleration and stopping are described as too lean: turn L counterclockwise about 1/4 turn until running uniformly and accelerating correctly.
- Varying idle speed with stopping when the machine is swivelled to another position is described as too rich: turn L clockwise about 1/4 turn until running uniformly and accelerating correctly.
- After changing L, LA usually needs adjustment. These are the source diagnostic symptoms and approximate corrections, not a substitute for the maintenance checks/basic setting or a guarantee every similar symptom has this cause. Page 15 requires the cutting tool not to turn at idle.
- Applies only to the listed TI 09 models with the stated C1Q-S82/S83 configuration. Shared sheets do not extend this evidence to FS 300, BT 121, R variants or later S161/S162/S163/S164/S138/S139 carburetors. No physical interchange test was performed.
Source: TI 9/2003, p. 14 · TI 9/2003, p. 15 · TI 9/2003, p. 17 — 2.1.4 continued: idle setting and lean/rich response.
Part numbers (2)
- 4134 120 0603 — C1Q-S82 carburetorSpecified service idle configuration · BT 120 C and FS 120; C1Q-S82 only
- 4134 120 0604 — C1Q-S83 carburetorSpecified service idle configuration · FS 200, FS 250 and FS 350; C1Q-S83 only
Service note · BT 120 C / FS 120 / FS 200 / FS 250 / FS 350
TI 09: C1Q-S82/S83 capped user setting and stationary tool
Capped H goes counterclockwise to its stop, max¾turn; L backs off 1 turn.
- Standard setting WITH H cap: switch engine off; fit cutting tool for brushcutters/clearing saws only; check/replace air filter as necessary. If the operator manual describes it, check and adjust throttle cable. Turn H counterclockwise as far as possible, maximum 3/4 turn. Carefully seat L clockwise lightly, then back it off 1 turn.
- Then start and warm the machine as necessary; adjust LA so the cutting tool does not turn. After any L adjustment, LA usually requires adjustment. Warm the engine before idle corrections.
- If the engine stops at idle: restore standard L setting, turn LA clockwise until the engine runs evenly; cutting tool should not turn. If attachment turns at idle: turn LA counterclockwise until it stops, then approximately 1/2 to 1 further turn in the same direction.
- After a new carburetor is fitted to an older machine, section 2.4.2 says the former operator-manual adjustment instructions no longer apply: give the user the new section 2.1.5/page 15 instructions. Page 14 identifies these as an extract from new-machine operator instructions. This is not a whole-manual import or hardware test.
- Applies only to the listed TI 09 models with the stated C1Q-S82/S83 configuration. Shared sheets do not extend this evidence to FS 300, BT 121, R variants or later S161/S162/S163/S164/S138/S139 carburetors. No physical interchange test was performed.
Source: TI 9/2003, p. 14 · TI 9/2003, p. 15 · TI 9/2003, p. 17 — 2.1.5 standard setting and 2.4.2 user instruction replacement.
Part numbers (2)
- 4134 120 0603 — C1Q-S82 carburetorCapped user setting · BT 120 C and FS 120; C1Q-S82 only
- 4134 120 0604 — C1Q-S83 carburetorCapped user setting · FS 200, FS 250 and FS 350; C1Q-S83 only
Service note · BT 120 C / FS 120 / FS 200 / FS 250 / FS 350
TI 09: C1Q-S82/S83 attachment and altitude adjustment limits
Keep metal tools at the standard setting; line-head setup and warm-up times remain explicit.
- A marginal H adjustment may be needed if the engine does not run satisfactorily. Before H adjustment on brushcutters/clearing saws, the source requires a nylon-line mowing head, lines reaching the deflector. Standard setting should be used for metal cutting tools or other attachments. Do not extend the mowing-head requirement to the BT 120C earth auger.
- Carry out standard setting, then warm up approximately 3 minutes with a mowing head or5 minutes with a metal cutting tool/other attachment. The metal-tool standard-setting restriction is retained; warm-up text does not cancel it.
- For mountain country the source describes full throttle and turning H clockwise (leaner) until speed ceases increasing; maximum speed is normally reached at standard setting. A marginal adjustment of approximately 1/8 turn per 1000 m (3300 ft) may be necessary. This is conditional historical guidance, not an automatic altitude correction, unrestricted leaning or a new maximum-rpm specification.
- H remains capped with maximum 270-degree travel. Use the capped standard-setting and stationary-cutting-tool idle instructions on the same page; the altitude paragraph does not override them.
- Applies only to the listed TI 09 models with the stated C1Q-S82/S83 configuration. Shared sheets do not extend this evidence to FS 300, BT 121, R variants or later S161/S162/S163/S164/S138/S139 carburetors. No physical interchange test was performed.
Source: TI 9/2003, p. 15 · TI 9/2003, p. 17 — 2.1.5 different working conditions and mountain-country instructions.
Part numbers (2)
- 4134 120 0603 — C1Q-S82 carburetorAttachment-specific capped setting · BT 120 C and FS 120; C1Q-S82 only
- 4134 120 0604 — C1Q-S83 carburetorAttachment-specific capped setting · FS 200, FS 250 and FS 350; C1Q-S83 only
Service note · BT 120 C / FS 120 / FS 200 / FS 250 / FS 350
TI 09: carburetor retrofit pin direction remains ambiguous
Page 16 reverses the page 8 pin change and still names C1Q-S35/S36/S51; do not invent a universal conversion.
- Section 2.4 requires new carburetor assembly, appropriate throttle cable pin and shroud; guide grommet may be removed. Older machines need nameplate 4134 967 1514 on the new shroud. Follow previous TI instructions before conversion; this is not a standalone fitment recipe.
- Page 8 section 1.12.2 (new throttle cable on existing carburetor) says replace pin 4128 121 8900 (5) with 4128 121 8901 (6) on C1Q-S35, -S36 and -S51. Page 16 section 2.4.1 instead says replace4128 121 8901 (6) with 4128 121 8900 (5), again naming C1Q-S35, -S36 and -S51, despite its new-carburetor conversion context. Both use diagram 250TI050, left existing and right new.
- The opposite directions occur in different conversion contexts and might reflect retention of a different cable, but that explanation is not established by these pages. The repeated old-carburetor names on page 16 also remain ambiguous. Preserve both instructions; do not silently correct the numbers, substitute S82/S83 in the prose, or claim one pin fits every cable/carburetor combination.
- Page16 prints shroud reference3.2 (actual heading2.2) and TI22.2201; neither printed error is silently repaired. Page7 explicitly requires TI21.2000,22.2001 and42.2002. All three have now been reviewed; see the TI09 conversion-prerequisite note for their conditional restrictions. The earlier locally actionable dependency review is complete, not a missing-source gap.
- Page16 then says attach the cable end and adjust the carburetor. Page17 requires replacement user adjustment instructions from page15. Section2.4 is now semantically reviewed with its dependencies, but the pin-direction and old-carburetor-name ambiguities remain unresolved. Semantic review does not establish universal interchange.
- Applies only to the listed TI 09 models with the stated C1Q-S82/S83 configuration. Shared sheets do not extend this evidence to FS 300, BT 121, R variants or later S161/S162/S163/S164/S138/S139 carburetors. No physical interchange test was performed.
Source: TI 9/2003, p. 7 · TI 9/2003, p. 8 · TI 9/2003, p. 16 · TI 9/2003, p. 17 — 1.11,1.12.2 versus2.4–2.4.2 retrofit dependencies and diagram 250TI050.
Part numbers (4)
- 4128 121 8900 — Throttle cable pin, diagram item 5Page 8 predecessor; page 16 replacement · BT 120 C, FS 120, FS 200, FS 250, FS 350; TI 09 section 2 configuration only
- 4128 121 8901 — Throttle cable pin, diagram item 6Page 8 replacement; page 16 predecessor · BT 120 C, FS 120, FS 200, FS 250, FS 350; TI 09 section 2 configuration only
- 4134 967 1514 — Nameplate for new shroud on older machinesRequired label sheet; dependency reviewed, model selection retained · BT 120 C, FS 120, FS 200, FS 250, FS 350; TI 09 section 2 configuration only
- 4134 123 7502 — Screwdriver guide grommetMay be removed with the new shroud · BT 120 C, FS 120, FS 200, FS 250, FS 350; TI 09 section 2 configuration only
Service note · BT 120 C / FS 120 / FS 200 / FS 250 / FS 350
TI 09: C1Q-S82/S83 shroud access and repair-parts set
New shroud gives direct adjustment access; repair set changes without deleting old-machine spares.
- New shrouds provide direct access to H/L/LA adjustments without a screwdriver guide grommet; symbols are on the shroud. Diagram 250TI053 compares old and new access;250TI054 shows the discontinued guide grommet 4134 123 7502. The production discontinuation is not a claim that spare supply for older machines stopped.
- Repairs to the new carburetor require the new set of carburetor parts 1129 007 1062 instead of 4134 007 1060. Summary row 14 carries both remarks 1 and 2: previous version remains available for older machines, and new carburetor parts are in the concerned machine parts list. Kit contents and universal interchange are not specified here.
- Summary row 13 also retains old guide grommet 4134 123 7502 for older machines under remark1. Availability is historical, not current stock. Use the exact model-specific shroud/carburetor pairs in the table and preserve unresolved retrofit pin/nameplate dependencies.
- Applies only to the listed TI 09 models with the stated C1Q-S82/S83 configuration. Shared sheets do not extend this evidence to FS 300, BT 121, R variants or later S161/S162/S163/S164/S138/S139 carburetors. No physical interchange test was performed.
Source: TI 9/2003, p. 16 · TI 9/2003, p. 17 — 2.1.6,2.2,2.3 and 2.5 all-machine rows/remarks.
Part numbers (3)
- 4134 123 7502 — Previous screwdriver guide grommetDiscontinued in new production; retained older-machine spare · BT 120 C, FS 120, FS 200, FS 250, FS 350; TI 09 section 2 configuration only
- 4134 007 1060 — Previous carburetor repair-parts setRemains for older machines · BT 120 C, FS 120, FS 200, FS 250, FS 350; TI 09 section 2 configuration only
- 1129 007 1062 — New carburetor repair-parts setRequired for new carburetor repairs; contents not specified · BT 120 C, FS 120, FS 200, FS 250, FS 350; TI 09 section 2 configuration only
Wrong number or missing part for the FS 120, FS 120 R, FS 200, FS 200 R, FS 250, FS 250 R? Report a correction →