← Augers/Drills & other equipment · series 4134

Stihl 4134 · Section H · 8 of 18 · 39 parts

Carburetor C1Q-S51C, C1Q-S36G (09.2003)

Fits FS 120, FS 120 R, FS 200, FS 200 R, FS 250, FS 250 R.

Parts diagrams →

Historical fitment & changes (4) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
110111213141516171819220212223242526272829330313233343536456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (39)

PosPart numberDescriptionQty
1 4116 121 5100 Inlet needle 1
2 1120 122 3004 Spring 1
3 1120 121 9200 Spindle 1
4 1125 121 5000 Inlet control lever 1
5 1120 122 6600 Collar screw 1
6 4137 122 5100 Outlet valve 1
7 1130 121 5601 Fixed jet 0.44 1
8 4119 121 0700 Cup plug 1
9 4129 121 0700 Cup plug 1
10 4129 129 0902 Gasket 1
11 4129 121 4700 Metering diaphragm 1
12 4134 121 0801 End cover → replaced by 4134 121 0803, 4134 121 0803 TI 6/2009 1
13 1120 122 6601 Collar screw 4
14 1130 122 6300 Idle speed adjustment screw Fitment / change note → 1
15 1123 122 3000 Spring 1
16 4134 120 7100 NLA Throttle shaft with lever 1
17 4134 123 7300 Lever 1
18 4134 122 5000 Spacer sleeve 1
19 4128 121 8900 Pin 1
20 4137 121 8600 Washer 1
21 1120 122 9000 E-clip 1
22 9079 319 0280 Flat head screw M3x3.5 1
23 1123 121 3300 NLA Throttle shutter Fitment / change note → → replaced by 4134 121 3300 TI 9/2003 1
24 1120 122 7400 Round head screw 1
25 1123 121 7800 Strainer 1
26 1129 121 4800 Pump diaphragm 1
27 1123 129 0905 Gasket 1
28 4128 121 0800 End cover → replaced by 1130 121 0801 TI 31/2009 1
29 1120 122 7800 Oval head screw 1
30 4119 122 3002 Spring 1
31 4119 122 4200 Ball 1
32 4134 121 3000 Choke shaft 1
33 4128 121 2900 Choke shutter 1
34 1125 122 7403 Round head screw 1
35 4134 121 5402 NLA Valve jet 1
36 4128 122 6300 NLA Idle speed adjustment screw Fitment / change note → 1
Not numbered on the diagram — assemblies, kits and options
— 4134 120 0651 NLA Carburetor C1Q-S51C Fitment / change note → 1
— not sold separately Carburetor C1Q-S36G no longer available from factory 1
— 4134 007 1060 Set of carburetor parts 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Conditional replacement · BT 120 C / FS 120 / FS 200 / FS 250 / FS 350

TI09: C1Q-S51 throttle shutter changes in two stages

The later shutter adds idle airflow; the two replacements are not one undifferentiated change.

  • First stage: throttle shutter 1123 121 3300 was replaced by 4134 121 3300. Second stage: 4134 121 3300 was replaced by 4134 121 3301, which has a hole allowing additional air to flow at idle.
  • The modified parts can be fitted to older C1Q-S51 carburetors. The summary associates the first shutter change with C1Q-S51B to C1Q-S51C and the later shutter plus idle screw with C1Q-S51C to C1Q-S51D. It does not give a hole diameter or permission to drill an older shutter.
  • Remark2 says the previous shutters remain available. Introduction is in progress; no serial cutoff or exact introduction date is supplied. Historical factory availability is not current stock verification.
  • Only the C1Q-S51 configurations of the printed BT 120 C, FS 120, FS 200, FS 250 and FS 350 models are covered. Shared C1Q-S36G/FS 300/R-variant sheets do not establish those carburetor or model applications. This is not a C1Q-S82/S83 conversion instruction. No physical interchange test was performed.

Source: TI 9/2003, p. 1 · TI 9/2003, p. 18 — 3.1 and3.3 throttle shutters and summary.

Part numbers (3)
  • 1123 121 3300 — Original throttle shutterFirst-stage predecessor · Listed TI09 models with C1Q-S51 only
  • 4134 121 3300 — Intermediate throttle shutterFirst replacement; second-stage predecessor · Listed TI09 models with C1Q-S51 only
  • 4134 121 3301 — Later throttle shutter with idle-air holeSecond replacement · Listed TI09 models with C1Q-S51 only

Conditional replacement · BT 120 C / FS 120 / FS 200 / FS 250 / FS 350

TI09: longer C1Q-S51 idle screw and supply conflict

The LD screw changes from 16.6 to 16.9 mm; prose and table disagree on old-part availability.

  • Idle speed adjustment screw LD 4134 122 6300 is replaced by slightly longer 1130 122 6300 to optimize adjustment range. Diagram250TI032 marks old dimension a = 16.6 mm (0.654 in) and new dimension b = 16.9 mm (0.665 in). These are the labeled diagram dimensions, not invented thread sizes or tuning settings.
  • Section3 permits the modified parts in older C1Q-S51 carburetors. Row6 groups the new screw with the later shutter in the C1Q-S51D stage; the order number alone does not identify an assembled carburetor revision.
  • Unresolved source conflict: section3.2 says the previous idle screw will be discontinued, while summary row6 carries remark2, previous version of part remains available. Preserve both statements; no chronology is invented to reconcile them, and neither proves current availability.
  • Introduction is in progress. No adjustment turns, idle RPM, production serial or substitute screw is specified in section3.
  • Only the C1Q-S51 configurations of the printed BT 120 C, FS 120, FS 200, FS 250 and FS 350 models are covered. Shared C1Q-S36G/FS 300/R-variant sheets do not establish those carburetor or model applications. This is not a C1Q-S82/S83 conversion instruction. No physical interchange test was performed.

Source: TI 9/2003, p. 1 · TI 9/2003, p. 18 — 3.2 LD screw diagram250TI032 and3.3 summary row6/remark2.

Part numbers (2)
  • 4134 122 6300 — Previous LD idle speed adjustment screw16.6 mm diagram dimension; supply conflict retained · Listed TI09 models with C1Q-S51 only
  • 1130 122 6300 — New LD idle speed adjustment screw16.9 mm diagram dimension; C1Q-S51 retrofit · Listed TI09 models with C1Q-S51 only

Conditional replacement · BT 120 C / FS 120 / FS 200 / FS 250 / FS 350

TI09: C1Q-S51B, C and D share one order number

4134 120 0651 does not identify which shutter and idle screw a carburetor contains.

  • C1Q-S51B, C1Q-S51C and C1Q-S51D all carry order number 4134 120 0651 in the summary. The first stage B to C changes shutter 1123 121 3300 to 4134 121 3300. The later C to D stage changes the shutter to 4134 121 3301 and the LD screw to 1130 122 6300. All other parts are as before within this section.
  • Remark1 is printed on the C1Q-S51C rows2 and4: the previous version is supplied only while factory stocks last, then item5 (C1Q-S51D) is supplied. Do not silently attach that remark to the unmarked B row or interpret the unchanged order number as unchanged contents.
  • Remark2 on the previous shutters and screw says they remain available; the screw prose contradicts that remark and is retained separately. These are historical supply statements, not an inventory promise. Introduction in progress supplies no numeric serial limit.
  • Only the C1Q-S51 configurations of the printed BT 120 C, FS 120, FS 200, FS 250 and FS 350 models are covered. Shared C1Q-S36G/FS 300/R-variant sheets do not establish those carburetor or model applications. This is not a C1Q-S82/S83 conversion instruction. No physical interchange test was performed.

Source: TI 9/2003, p. 1 · TI 9/2003, p. 18 — 3.3 complete summary and remarks.

Part numbers (6)
  • 4134 120 0651 — C1Q-S51B / C / D carburetor assemblySame number across revised contents · Listed TI09 models with C1Q-S51 only
  • 1123 121 3300 — B-stage shutterOriginal · Listed TI09 models with C1Q-S51 only
  • 4134 121 3300 — C-stage shutterIntermediate · Listed TI09 models with C1Q-S51 only
  • 4134 121 3301 — D-stage shutterWith idle-air hole · Listed TI09 models with C1Q-S51 only
  • 4134 122 6300 — Previous LD screwAvailability conflict · Listed TI09 models with C1Q-S51 only
  • 1130 122 6300 — D-stage LD screwLonger replacement · Listed TI09 models with C1Q-S51 only

Conditional replacement · FS 120 / FS 200 / FS 350 / BT 120 C

TI22: C1Q-S51A/B share a number but use different idle screws

The original screw remains for older carburetors; printed metric and inch dimensions disagree.

  • C1Q-S51A becomes C1Q-S51B when idle screw 4128 122 6300 changes to 4134 122 6300 to improve acceleration and idle. Both carburetor versions use 4134 120 0651; all other parts remain as before. Introduction is in progress, with no serial.
  • Previous screw 4128 122 6300 remains available for previous carburetors. The illustration labels old span a as 17.3 mm (0.681 inch) and new span b as 16.9 mm (0.655 inch). The new printed units are inconsistent: 16.9 mm is about 0.665 inch, not 0.655. Both original values are retained; do not silently select a corrected manufacturing dimension.
  • This is the earlier A-to-B change, not the later S51C idle-screw availability conflict in TI09/2003. No chronology resolving that later contradiction is inferred.
  • TI22 describes an interdependent update package. Its introduction says most new parts were fitted to FS 250 from production start, with unspecified exceptions; this is not blanket FS 250 fitment approval. Shared sheets do not extend the named model/configuration scope. Factory availability is historical, not current stock. No physical interchange test was performed.

Source: TI 22/2001, p. 4 — 4 entire drawing, dimensions, prose and summary.

Part numbers (3)
  • 4134 120 0651 — C1Q-S51A / C1Q-S51B carburetorSame number; version matters · FS 120, FS 200, FS 350, BT 120 C; stated configuration only
  • 4128 122 6300 — Previous idle speed screwRetained for previous carburetors · FS 120, FS 200, FS 350, BT 120 C; stated configuration only
  • 4134 122 6300 — New idle speed screwS51B revision · FS 120, FS 200, FS 350, BT 120 C; stated configuration only

Wrong number or missing part for the FS 120, FS 120 R, FS 200, FS 200 R, FS 250, FS 250 R? Report a correction →