Stihl 4137 · Section P · 14 of 24 · 27 parts
HT 70: Drive tube assembly, Gear head
Fits HT 70.
Historical fitment & changes (3) — includes parts and conditions not shown on this drawing.
Parts (27)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4138 710 7110 | Drive tube assembly Ø 25.4 mm / 1'' | 1 |
| 2 | 4137 711 7300 | Flexible liner 1455 mm / 57 5/16'' | 1 |
| 3 | 4137 711 2101 | Plug | 2 |
| 4 | 4138 791 2010 | Handle hose | 1 |
| 5 | 4137 711 3200 | Drive shaft → replaced by 4137 711 3202 TI 11/2005 | 1 |
| 6 | 4140 007 1006 | Hose clamp kit | 1 |
| 7 | 9022 341 1270 | Spline screw IS-M6x14 | 1 |
| 8 | 4138 641 0300 | Gear housing → replaced by 4138 640 0551 TI 22/2011 no longer available from factory | 1 |
| 9 | 4138 640 3200 | Oil pump | 1 |
| 10 | 4138 640 7303 | Set of pinions 1.27 | 1 |
| 11 | 9503 003 9860 | Grooved ball bearing 609-2RS | 1 |
| 12 | 9503 003 5190 | Grooved ball bearing 6001-2RS | 1 |
| 13 | 9503 003 5030 | Grooved ball bearing 6000-2RS | 2 |
| 14 | 9455 621 0850 | Circlip 10x1 | 1 |
| 15 | 4138 641 0400 | Gearbox cover | 1 |
| 16 | 9022 341 1050 | Spline screw IS-M5x25 | 8 |
| 17 | 4138 642 8200 | Ring | 1 |
| 18 | 0000 958 0506 | Washer | 2 |
| 19 | 1206 642 1301 | Chain sprocket 3/8" Picco 7T | 1 |
| 20 | 9460 624 0801 | E-clip 8x1.3 | 1 |
| 21 | 0000 953 1402 | Stud M8 → replaced by 1129 664 2401 TI 20/1997 | 1 |
| 22 | 4138 351 9300 | Strainer | 1 |
| 23 | 4138 353 2900 | Rubber buffer | 1 |
| 24 | 0783 830 2000 | Tube of sealant Dirko HT red option | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 0781 120 1110 | Gear lubricant 225 g not illustratedoption | 1 |
| — | 4138 640 0111 | Gearhead | 1 |
| — | 0781 120 1118 | Gear lubricant 225 g not illustratedoption | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · HT 70
HT 70: rigid shaft and introductory dimensions
Rigid shaft in a protective liner; 0.9 kW, 4.9 kg and approximately 180/210 cm lengths are the 1998 introduction values, not a telescopic-shaft specification.
- The introduction describes a lightweight pole pruner with a RIGID SHAFT, a 0.9 kW / 1.2 bhp engine and a weight of 4.9 kg / 10.8 lb. It does not state whether the weight includes fuel or cutting attachment; do not invent that measurement condition.
- Apart from the SHAFT, the source says components and assemblies are exactly the same as HT 75, with identical applications. The shorter rigid shaft particularly suits lower cutting heights. This is a dated source comparison, not a blanket present-day parts substitution or a telescopic-shaft fitment claim.
- Section 1 describes a drive tube with rigid shaft running in a protective liner. The overall product photograph shows that configuration, but supplies no internal part number or installation dimension.
- Section 2 gives approximate overall lengths: WITHOUT cutting attachment 180 cm (70.86 inches); WITH cutting attachment 210 cm (82.7 inches). Other specifications are referred to HT 75, not independently supplied here. No working-reach, extension, serial range or shaft interchange dimension is inferred.
- Historical HT 70 only. TI35/1998 calls this series 4138; the retained exact-model IPL is filed under 4137. That navigation association does not establish series equivalence, extend these assertions to HT 75 or later variants, or prove physical interchange. No production serial or current stock claim is supplied. No hardware operation was performed.
Source: TI 35/1998, p. 1 · TI 35/1998, p. 2 — Introduction, product photograph and sections 1–2 complete.
No additional parts-table entry added.
Service note · HT 70
HT 70: carburetor kit and separate lubricant applications
Kit 4227 007 1060 is listed for Zama C1Q-S28C / C1Q-S41; oil-seal, gearbox and drive-shaft greases have separate order numbers and tube sizes.
- Carburetor parts kit 4227 007 1060 is assigned to Zama C1Q-S28C and C1Q-S41 as printed. Do NOT silently change those suffixes to the later catalog sheet C1Q-S28E / C1Q-S41C. The shared sheet is only navigation; kit contents and applicability to later suffixes are not established here.
- Lube grease 0781 120 1111, 225 g / 8 oz TUBE: OIL SEALS. Lube grease 0781 120 6602, 40 g / 1.4 oz TUBE: GEAR BOX. Lube grease 0781 120 1109, 80 g / 2.8 oz TUBE: DRIVE SHAFT. These are package sizes, NOT quantities to install.
- The three printed application labels are retained independently. Do not swap grease applications, infer equivalence with other editions or treat tube mass as a gearbox fill. No maintenance interval, fill amount or replacement product is specified by this table. Existing lubricant/application conflicts in other notes remain unchanged.
- Historical HT 70 only. TI35/1998 calls this series 4138; the retained exact-model IPL is filed under 4137. That navigation association does not establish series equivalence, extend these assertions to HT 75 or later variants, or prove physical interchange. No production serial or current stock claim is supplied. No hardware operation was performed.
Source: TI 35/1998, p. 3 — Section 5.2 complete table; section 5.1 reference retained separately.
Part numbers (4)
- 4227 007 1060 — Carburetor parts kitHistorical servicing kit · HT 70; TI35/1998 Zama C1Q-S28C and C1Q-S41 only as printed
- 0781 120 1111 — Lube grease, 225 g / 8 oz tubeOil-seal servicing aid · HT 70; TI35/1998 oil seals; package size, not installed quantity
- 0781 120 6602 — Lube grease, 40 g / 1.4 oz tubeGearbox servicing aid · HT 70; TI35/1998 gear box; package size, not fill amount
- 0781 120 1109 — Lube grease, 80 g / 2.8 oz tubeDrive-shaft servicing aid · HT 70; TI35/1998 drive shaft; package size, not installed quantity
Service note · HT 70
HT 70: repair references and historical parts-list issue
Available HT70 repair dependencies reviewed; exact historical handbooks, owner precautions and the 3.98 IPL remain documented source gaps.
- Section 5.1 says the same special servicing tools are used as for FS 85 brushcutters. Section 6.1 says setting/testing data and other information are the same as HT 75 and FS 85 brushcutters (SHAFT). This supplies no numeric setting, torque or tool order number; it does not make the HT70 a brushcutter.
- The named service manual is FS 75, 80, 85, FC 75, HL 75; missing GEARHEAD procedures are delegated to TI03/1997. Applicable retained TI procedures and later explicitly HT70-bound Components (2005-04), Powerhead (2004-03) and CombiTools (2007-02) sections have been reviewed separately. Exact historical FS manual and E14/E20 tensioner-manual editions remain bounded source gaps. Later sources do not prove original 1998 configuration; HT75-only revisions are not silently rebound to HT70.
- The cited historical manual omits Servicing the Carburetor, Troubleshooting and standard procedures, delegating them to separate CARBURETOR and STANDARD REPAIRS, TROUBLESHOOTING handbooks. Neither requested handbook is established in the retained PDF inventory, reviewed manual headers and reference-document index. The available Chain and Bar, Special Tools, 019 T, 020 T and HS/BG service manuals are different works. Their references to handbooks are not the handbooks themselves. This is a bounded source gap, not universal absence; later HT70-specific carburetor/troubleshooting content remains separately reviewed evidence.
- If the unit is STARTED during repair or maintenance, section 6 requires all LOCAL SAFETY REGULATIONS and the OWNER’S MANUAL safety precautions. The exact HT70 owner-safety source is not established in the retained archive inventory or HT70/HT75 document links; repair-manual safety paragraphs do not replace it. No start-up or under-load test was performed, and review closure is not bench readiness.
- Section 7 says HT70 parts will be incorporated in the existing HT75 list and are included in the 3.98 microfiche/CD-ROM issue. The retained 2012 catalog links HT70/HT75 to later IPL documents, including a gearhead entry marked 11.2005 and a gear-housing conversion kit marked 22.2011. No exact 3.98 edition is established by that index or the retained PDF inventory. Later drawings are useful navigation, not proof of 1998 parts, supersession, introduction serial, current stock or publication authorization. The copyright/footer adds no interchange assertion.
- Historical HT 70 only. TI35/1998 calls this series 4138; the retained exact-model IPL is filed under 4137. That navigation association does not establish series equivalence, extend these assertions to HT 75 or later variants, or prove physical interchange. No production serial or current stock claim is supplied. No hardware operation was performed.
Source: TI 35/1998, p. 3 · TI 35/1998, p. 4 — Sections 5.1, 6 safety paragraph, 6.1 and 7; retained dependency review complete with bounded exact-source gaps.
No additional parts-table entry added.
Wrong number or missing part for the HT 70? Report a correction →