← Special-purpose Units & other equipment · series 4137

Stihl 4137 · Section C · 3 of 15 · 25 parts

Ignition system, Clutch

Fits KW 85.

Parts diagrams →

Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1101112131415161617181922021222324253456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (25)

PosPart numberDescriptionQty
1 4137 400 1200 Flywheel 1
2 4137 400 1350 Ignition module Fitment / change note → 1
3 4137 442 0400 Insulating hose Fitment / change note → 1
4 1106 405 1000 Spark plug boot → replaced by 1128 405 1000, 1128 405 1000 TI 30/1995 1
5 0000 998 0606 Torsion spring 1
6 4137 405 1600 Plug connector 1
7 4137 404 9300 Washer Fitment / change note → 2
8 9022 371 0710 Spline screw IS-M4x20 Fitment / change note → 2
9 4137 160 2001 Clutch 1
10 1129 162 0800 Clutch shoe 3
11 1127 162 3000 Retainer 3
12 0000 997 5625 Tension spring 3
13 1121 162 3000 Retainer 3
14 4137 080 1800 Fan housing Fitment / change note → 1
15 9991 003 5087 Sleeve 7.5x6.8 3
16 9022 341 0980 Spline screw IS-M5x16 5
17 4137 160 2900 Clutch drum 1
18 9455 621 1130 Circlip 12x1 1
19 4137 791 9300 Rubber insert 1
20 9457 621 4481 Circlip 1
21 4137 790 7200 Sleeve 1
22 9075 478 4095 Pan head self-tapping screw IS-D5x12 1
23 9022 371 1020 Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 1
24 4137 080 1604 Shroud 1
25 4602 967 1500 Model plate KW 85 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Conditional replacement · FH 75 / HL 75 / HL 75 K / HT 70 / HT 75 / FC 75 / FC 85 / KW 85 / FS 75 / FS 80 / FS 85 / FS 85 T

4137 ignition: MB kit replaces MB or AD modules

Identify module type and retain its mounting sequence; introduction serials differ by model.

  • Identify the module by its two-letter vendor type code and the final four STIHL part-number digits: AD (1304) versus MB (1307). A longer spark duration is the vendor-stated operating-range benefit, not a reproduced measurement. No complete AD ordering number is printed; do not derive one from 1304.
  • Type MB4137 400 1307 was no longer supplied separately; kit 4137 400 1350 includes the MB module, mounting hardware and illustrated installation instructions and replaces either MB or AD. AD was not yet available as a spare. The page 8 drawing shows different mounting sequences for AD and MB; use the version-specific instructions, not an assumed common washer stack. Separate kit instructions were not located in the retained inventory. Later general ignition procedures do not establish the AD/MB-specific mounting stack; this remains a documented source gap.
  • The summary retains two washers 4137 404 9300 and insulating tube 4137 442 0400, lists two new A5.3 washers 9291 021 0121, and changes two IS-M4 x 20 screws from 9022 313 0710 to 9022 371 0710. Old screws remain spares for other models. Insulating tube is not required for BG 75 or HS 75/80/85. No torque or air gap is specified here.
  • Ignition introduction is model-specific: HS 80 from 2 49 943 796; FS 85 from 2 49 848 196; HT 75 from 2 50 062 280; other models in progress. These are not model production ranges or a universal update cutoff. Chapter 1 prints a different FS 85 update serial 2 49 849 196; retain both without replacing the ignition-specific statement.
  • Only explicitly named models/configurations are covered; shared IPL sheets do not extend this note to other variants. Availability describes 2001 factory supply, not present stock. Retained engine-sheet series are navigation, not proof of series equivalence.

Source: TI 16/2001, p. 8 · TI 16/2001, p. 9 — Sections 4–4.4: ignition identification, mounting drawing, kit and summary.

Part numbers (7)
  • 4137 400 1307 — Ignition module type MBPrevious separate module · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
  • 4137 400 1350 — Type MB ignition module kitReplacement for MB and AD · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
  • 4137 404 9300 — Washer, twoUnchanged · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
  • 4137 442 0400 — Insulating tubeUnchanged; omitted on BG 75 and HS 75/80/85 · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
  • 9291 021 0121 — Washer A5.3, twoNew mounting hardware · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
  • 9022 313 0710 — Screw IS-M4 x 20, twoPrevious; retained for other models · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
  • 9022 371 0710 — Screw IS-M4 x 20, twoNew · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only

Conditional replacement · FH 75 / HL 75 / HL 75 K / HT 70 / HT 75 / FC 75 / FC 85 / KW 85 / FS 75 / FS 80 / FS 85 / FS 85 T

4137 fan housing: strengthened version, unchanged number

The lower housing is reinforced; the A/B drawing labels distinguish versions, not new order numbers.

  • The lower part of fan housing 4137 080 1800 was strengthened. The drawing labels old 4137 080 1800 A and new 4137 080 1800 B; the summary explicitly keeps 4137 080 1800 unchanged. Do not turn A/B into invented order numbers.
  • Only the modified version was supplied from the factory. Introduction refers to chapter 1; no clean numeric cutoff is assigned because the TI retains differing FS 85 serial statements.
  • Only explicitly named models/configurations are covered; shared IPL sheets do not extend this note to other variants. Availability describes 2001 factory supply, not present stock. Retained engine-sheet series are navigation, not proof of series equivalence.

Source: TI 16/2001, p. 12 · TI 16/2001, p. 13 — Section 8 and continued summary: strengthened fan housing.

Part numbers (1)
  • 4137 080 1800 — Fan housingSame number; modified lower section · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only

Wrong number or missing part for the KW 85? Report a correction →