Stihl 4201 · Section G · 7 of 24 · 36 parts
Ignition system
Fits TS 510, TS 760.
Historical fitment & changes (6) — includes parts and conditions not shown on this drawing.
Parts (36)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1111 404 1204 | Flywheel Fitment / change note → | 1 |
| 2 | 9210 261 1140 | Hexagon nut M8x1 | 1 |
| 3 | 1111 400 1301 | Ignition coil Fitment / change note → | 1 |
| 4 | not sold separately | Ignition lead 320 mm not available as a separate item | 1 |
| 5 | 0000 989 1010 | Grommet Fitment / change note → | 1 |
| 6 | 1110 442 7000 NLA | Contact sleeve Fitment / change note → no longer available from factory | 1 |
| 7 | 1111 448 1200 | Lead retainer Fitment / change note → | 1 |
| 8 | 0000 989 0808 | Grommet Fitment / change note → | 1 |
| 9 | 1111 400 1303 | Ignition module Fitment / change note → → replaced by 1111 400 1301 TI 33/1995 | 1 |
| 10 | not sold separately | Ignition lead 290 mm not available as a separate item | 1 |
| 11 | 4205 400 1001 | Trigger unit Fitment / change note → | 1 |
| 12 | 4205 400 1002 NLA | Trigger unit | 1 |
| 13 | 1118 400 1001 | Trigger unit | 1 |
| 14 | 9045 371 0960 | Socket head screw M5x12 | 2 |
| 15 | 9041 216 0300 | Pan head screw M3x4 Fitment / change note → | 1 |
| 16 | 9027 068 1480 | Flat head screw M6x75 Fitment / change note → | 1 |
| 17 | 9214 320 0900 | Lock nut M6 | 1 |
| 18 | 1111 405 8800 | Hose | 1 |
| 19 | 9022 371 1020 | Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 | 3 |
| 20 | 9291 021 0120 | Washer 5.3 | 3 |
| 22 | 4205 350 3600 | Hose | 1 |
| 23 | 1110 353 8102 | Insert | 1 |
| 24 | 1120 358 8105 | Vent insert | 1 |
| 25 | 1111 358 7700 | Hose | 1 |
| 26 | 1111 353 2500 | Elbow connector | 1 |
| 27 | 4205 353 5900 | Tank vent | 1 |
| 28 | not sold separately | Hose 3.1x5.7x135 mm, R3 not available as a separate item | 1 |
| 29 | not sold separately | Hose 3.1x5.7x365 mm / 14 3/8'', R3 not available as a separate item | 1 |
| 29 | not sold separately | Hose 3.1x5.7x325 mm, R3 not available as a separate item | 1 |
| 30 | 4205 647 9100 | Grommet | 1 |
| 31 | 4205 141 8602 | Hose 200 mm / 7 7/8'' | 1 |
| 32 | 0000 350 3502 | Pickup body | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 0000 405 0600 NLA | Ignition lead 1 m option | 1 |
| — | 0000 930 2251 | Ignition lead 10 m option | 1 |
| — | 0000 930 2803 | Hose 3.1x5.7 mm x 1 m, R3 option | 1 |
| — | 0712 923 8004 | Hose 3.1x5.7 mm x 10 m, R3 option | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Historical fitment · TS 510 / TS 760
TS 510 / TS 760: series 4205 replacement ignition assignment
1111 400 1301 + 4205 400 1001 with flywheel 1111 404 1204; 320 mm ignition lead.
- Printed series 4205. Use 1111 400 1301 and 4205 400 1001 with flywheel 1111 404 1204.
- Printed ignition-lead length: 320 mm (12 5/8 in). Preserve both printed units.
- TI01/1999 lists replacement combinations for the then-current machines, not every earlier configuration. Older machines are referred to Spare Parts for Previous Models in their own illustrated parts lists; no serial cutoff is supplied here.
- Use only the listed ignition-module/flywheel combinations. The source warns that incorrect combinations can cause excessive RPM or running in reverse; sharing a module number does not make all flywheels interchangeable.
- Universal replacement modules may differ from production modules in maker, shape and part number. The source describes installation/function compatibility within its assignments, not universal compatibility or a project hardware test.
- Some replacement modules require shortening the ignition lead and/or short-circuit wire and crimping a different short-circuit connector. The table gives ignition-lead lengths only; it supplies neither a short-circuit-wire length nor a connector part number. Do not infer that every row needs modification.
- Only the named models and printed series are covered. A shared IPL sheet does not extend this assignment to unnamed models or modern MS equivalents. This 1999 USA bulletin is historical guidance, not current availability.
- Footnote 1 identifies an ignition coil; footnote 2 identifies a separate trigger unit. These are components of the listed system, not two interchangeable replacement modules.
- The bulletin prints series 4205; the retained exact-model ignition sheets are cataloged under 4201. This link is an exact model-label navigation aid, not proof that the printed series identifiers are equivalent. Verify the actual machine configuration.
Source: TI 1/1999, p. 1 · TI 1/1999, p. 3 — 1.1 general restrictions and 1.2.2 power-tool assignments.
Part numbers (3)
- 1111 400 1301 — Ignition coilAssigned component · TS 510 / TS 760, printed series 4205, listed combination only
- 4205 400 1001 — Trigger unitAssigned component · TS 510 / TS 760, printed series 4205, listed combination only
- 1111 404 1204 — Assigned flywheelRequired pairing · TS 510 / TS 760, printed series 4205
Service note · TS 510 / TS 760
TS 510 / TS 760 electronic governor: separate coil and trigger
From X 24 073 218, ignition governs speed instead of the carburetor control valve.
- From machine number X 24 073 218, speed governing moves from the carburetor control valve to the ignition system. Original ignition module 1111 400 1303 is replaced by coil 1111 400 1301 PLUS SEPARATE trigger unit 4205 400 1000. Original module REMAINS A SPARE FOR OLDER MACHINES AND OTHER MODELS; those other models are not named and are not admitted as new fitment.
- New coil ignition lead is 320 mm (12.6 in) long. The -*- lead row means CUT FROM A COIL OF REPLACEMENT IGNITION LEAD, not a printed ordering number. Module/coil summary includes items 1–5 as applicable: lead, unchanged grommet 0000 989 1010, NEW cable retainer 1111 448 1200, NEW grommet 0000 989 0808, unchanged contact sleeve 1110 442 7000. Old-column dashes for retainer and second grommet must not become old-module inclusions.
- Separate trigger row 6 and M3x4 pan-head screw 9041 216 0300 row 7 are outside the stated module/coil items 1–5 inclusion. To accommodate the trigger, ONE M6x75 flat-head screw 9027 068 1480 replaces one original M6x72 screw 9027 068 1540. Remark 3 reduces M6x72 quantity FROM TWO TO ONE; the dash in the new column does NOT delete the remaining original-length screw.
- No numeric governed rpm, coil gap, torque, carburetor conversion procedure or general retrofit permission is given. Source heading says series4205; retained exact TS 510/TS 760 ignition sheet is consolidated under4201. Exact named-model binding is not inferred series equivalence.
- Later exact-model ignition sheet G lists trigger 4205 400 1001/1002 and 1118 400 1001, not TI 4205 400 1000. No trigger supersession chain is inferred; the source-reviewed new arrangement requires its explicitly stated separate trigger. A parsed module-to-coil arrow alone is not a complete replacement system.
- Historical TI guidance for the named models only. Shared catalog sheets do not extend applicability to other variants or successors. Factory supply statements are historical, not current stock guarantees or verified physical interchange. No hardware operation was performed.
Source: TI 33/1995, p. 1 — TS 510 / TS 760 electronic governor: separate coil and trigger.
Part numbers (10)
- 1111 400 1303 — Original ignition moduleolder-machine and other-model spare · TS 510 / TS 760; TS 510 / TS 760 electronic governor: separate coil and trigger
- 1111 400 1301 — New ignition coilused with separate trigger · TS 510 / TS 760; TS 510 / TS 760 electronic governor: separate coil and trigger
- 4205 400 1000 — Trigger unitseparate new component · TS 510 / TS 760; TS 510 / TS 760 electronic governor: separate coil and trigger
- 0000 989 1010 — Grommetunchanged · TS 510 / TS 760; TS 510 / TS 760 electronic governor: separate coil and trigger
- 1111 448 1200 — Cable retainernew coil component · TS 510 / TS 760; TS 510 / TS 760 electronic governor: separate coil and trigger
- 0000 989 0808 — Second grommetnew coil component · TS 510 / TS 760; TS 510 / TS 760 electronic governor: separate coil and trigger
- 1110 442 7000 — Contact sleeveunchanged · TS 510 / TS 760; TS 510 / TS 760 electronic governor: separate coil and trigger
- 9041 216 0300 — M3x4 pan-head screwtrigger hardware · TS 510 / TS 760; TS 510 / TS 760 electronic governor: separate coil and trigger
- 9027 068 1480 — M6x75 flat-head screwone fitted · TS 510 / TS 760; TS 510 / TS 760 electronic governor: separate coil and trigger
- 9027 068 1540 — M6x72 flat-head screwquantity reduced from two to one · TS 510 / TS 760; TS 510 / TS 760 electronic governor: separate coil and trigger
Service note · TS 510 / TS 760
TS 510 / TS 760 trigger mounting: bracket contact and insulation
Bracket must butt against the crankcase; coat screw head and terminal with insulating paste.
- Trigger unit 4205 400 1000 MUST be mounted with its bracket BUTTING AGAINST THE CRANKCASE, as the page 2 arrow shows. This is a required positional contact, not a printed clearance dimension.
- The SCREW HEAD AND TERMINAL on the trigger unit MUST be coated with insulating paste 0783 820 0110. Do not substitute thread locking, apply a torque inferred from screw diameter, or treat the illustration as a complete wiring/test procedure.
- Applies to the new electronic-governor arrangement introduced from X 24 073 218. No paste quantity, cure time, alternative product or electrical test limits supplied.
- Historical TI guidance for the named models only. Shared catalog sheets do not extend applicability to other variants or successors. Factory supply statements are historical, not current stock guarantees or verified physical interchange. No hardware operation was performed.
Source: TI 33/1995, p. 1 · TI 33/1995, p. 2 — TS 510 / TS 760 trigger mounting: bracket contact and insulation.
Part numbers (2)
- 4205 400 1000 — Trigger unitbracket against crankcase · TS 510 / TS 760; TS 510 / TS 760 trigger mounting: bracket contact and insulation
- 0783 820 0110 — Insulating pasterequired on screw head and terminal · TS 510 / TS 760; TS 510 / TS 760 trigger mounting: bracket contact and insulation
Historical fitment · TS 510 / TS 760
TS 510 / TS 760: 8400 RPM trigger and printed component numbers
Order numbers and markings on the trigger are different; section 6.1 also contains a number conflict.
Later reviewed guidance: TS 760: 400 mm wheels are factory-version only
- Section 5 replaces trigger unit 4205 400 1000 with 4205 400 1001 from X 24 097 471, in connection with 400 mm cutting wheels. The new trigger limits ENGINE speed to 8400 RPM. Maximum SPINDLE speeds are separately given as 4700 rpm with 400 mm (16 in.) wheels and 4900 rpm with 350 mm (14 in.) wheels; these are not interchangeable engine-speed settings.
- Original drawing 328TI015 distinguishes the original trigger ORDER number 4205 400 1000 by printed component marking 4205 400 1005, and the new ORDER number 4205 400 1001 by marking 4205 400 1006. The bulletin explicitly warns that the number printed on the component is NOT its spare-part order number. Marking-only search must not become an order recommendation.
- Section 6.1 on page 11 literally requires trigger 4201 400 1001 for the 400 mm kit, whereas section 5 prose, caption and table all specify 4205 400 1001. Both original scans confirm this unresolved printed conflict; preserve 4201 as a conflicting citation, not a second verified compatible trigger or silently corrected number. The common explicit requirement is 8400 RPM limiting and the complete specified attachment.
- Original trigger supply lasts only until stocks are exhausted. The earlier X 24 073 218 electronic-limiting event in section 2.1/TI33/1995 is distinct from this 8400 RPM change. Later exact sheet G lists 4205 400 1001 alongside 4205 400 1002 and 1118 400 1001; their co-listing does not prove the latter two satisfy this 400 mm requirement.
- Historical TI26/1996 sections 5–7, applied here to TS 510 and TS 760 only. Shared catalog sheets do not establish unrestricted interchange. Supply statements describe 1996, not current stock. No hardware operation was performed.
Source: TI 26/1996, p. 1 · TI 26/1996, p. 10 · TI 26/1996, p. 11 — TS 510 / TS 760: 8400 RPM trigger and printed component numbers.
Part numbers (5)
- 4205 400 1000 — Original trigger unitOrder number; stock exhaustion · TS 510 / TS 760; TS 510 / TS 760: 8400 RPM trigger and printed component numbers
- 4205 400 1001 — New 8400 RPM trigger unitSection 5 order number · TS 510 / TS 760; TS 510 / TS 760: 8400 RPM trigger and printed component numbers
- 4205 400 1005 — Printed original trigger markingIdentification only; NOT order number · TS 510 / TS 760; TS 510 / TS 760: 8400 RPM trigger and printed component numbers
- 4205 400 1006 — Printed new trigger markingIdentification only; NOT order number · TS 510 / TS 760; TS 510 / TS 760: 8400 RPM trigger and printed component numbers
- 4201 400 1001 — Section 6.1 printed trigger referenceUnresolved conflict; NOT verified fitment · TS 510 / TS 760; TS 510 / TS 760: 8400 RPM trigger and printed component numbers
Historical fitment · TS 510 / TS 760
TS 510 / TS 760: complete 400 mm attachment and belt guard
The larger pulley, reinforced support, correct belt guard and 8400 RPM limiter are joint conditions.
Later reviewed guidance: TS 760: 400 mm wheels are factory-version only
- Section 6.1 announces future availability of 400 mm (16 in.) attachment kits and cutting wheels, not evidence that every earlier machine was equipped for them. The kit has an aluminium guard, larger V-belt pulley, reinforced bearing and 103 mm thrust washers. Fit ONLY the COMPLETE attachment kit with reinforced bearing and larger pulley, together with V-belt guard 4201 700 8116, on a TS 510/760 limited to 8400 RPM. The trigger reference conflicts (section 5:4205 400 1001; section 6.1:4201 400 1001) and remains unresolved, not a verified alternative.
- The larger pulley is 4205 704 1004 (summary item 8). V-belt guard 4201 700 8114 is deleted as the standard version and replaced by 4201 700 8116 to accommodate that pulley diameter. The new guard and eccentric adjuster are supplied in the 400 mm kit 4205 007 1018; adjuster item 10 remains 4205 708 3201 in BOTH old and new columns. The kit inclusion range is 2,3,6,7,8,9,10, not every row in the summary.
- The TWO front rubber vibration buffers (machine rests), item 12, change 4205 790 9300 to lengthened 4205 790 9301, increasing wheel-to-ground clearance when switching off. The prose says generally replaced; do not claim these separately listed buffers are included within the 400 mm kit’s stated item range. Old belt guard and rubber buffers remain available only until stocks are exhausted (remark 3).
- Later sheets E and N each list the new rubber buffer at different locations, with the original also on N; these are not proof that every configuration has the 1996 pair installed. Later sheet O has the larger pulley but a different belt-guard listing 4205 706 8105 and support/guard alternatives; that does not erase the explicitly printed 1996 complete-kit restriction or prove a supersession chain.
- Historical TI26/1996 sections 5–7, applied here to TS 510 and TS 760 only. Shared catalog sheets do not establish unrestricted interchange. Supply statements describe 1996, not current stock. No hardware operation was performed.
Source: TI 26/1996, p. 1 · TI 26/1996, p. 10 · TI 26/1996, p. 11 · TI 26/1996, p. 12 · TI 26/1996, p. 13 — TS 510 / TS 760: complete 400 mm attachment and belt guard.
Part numbers (7)
- 4205 007 1018 — 400 mm complete attachment kitUSA; all stated conditions required · TS 510 / TS 760; TS 510 / TS 760: complete 400 mm attachment and belt guard
- 4205 704 1004 — Larger V-belt pulley400 mm kit item 8 · TS 510 / TS 760; TS 510 / TS 760: complete 400 mm attachment and belt guard
- 4201 700 8114 — Original V-belt guardStock exhaustion · TS 510 / TS 760; TS 510 / TS 760: complete 400 mm attachment and belt guard
- 4201 700 8116 — New V-belt guardRequired with 400 mm kit · TS 510 / TS 760; TS 510 / TS 760: complete 400 mm attachment and belt guard
- 4205 708 3201 — Eccentric adjusterUnchanged number; included · TS 510 / TS 760; TS 510 / TS 760: complete 400 mm attachment and belt guard
- 4205 790 9300 — Original rubber vibration bufferTwo front rests; stock exhaustion · TS 510 / TS 760; TS 510 / TS 760: complete 400 mm attachment and belt guard
- 4205 790 9301 — Lengthened rubber vibration bufferTwo front rests; increased ground clearance · TS 510 / TS 760; TS 510 / TS 760: complete 400 mm attachment and belt guard
Conditional replacement · TS 510 / TS 760
TS 510 / TS 760: 9,200 RPM trigger requires matching control valve
The 16-inch TS 760 is excluded from the trigger change. Printed trigger identification numbers are not spare-part order numbers.
- TI32/1999 names TS 510 and TS 760, series 4205. Exact-model navigation is under catalog family 4201 in the 2012 IPL; this does not change the source type or extend applicability to TS 350/360. Historical availability is not current stock, and source review is not verified physical interchange.
- The cut-off speed changes from 8,400 RPM to 9,200 RPM from serial 3 38 376 502 for TS 510 and 3 38 377 502 for TS 760. The special TS 760 version for 16-inch cutting wheels is not affected by this change of trigger unit. These are model-specific printed serial thresholds, not a universal date, cutting-wheel speed rating or permission to raise the speed of an arbitrary machine.
- Trigger unit order number 4205 400 1001 (8,400 RPM) is replaced by 4205 400 1000 (9,200 RPM), subject to the 16-inch exception. The page 1 top drawing shows printed identification 4205 400 1006 on the previous unit; the bottom shows 4205 400 1005 on the new unit. These printed identification numbers are not spare-part order numbers. Drawing 328TI000 KN and its captions distinguish identification from ordering; no false replacement-part rows are created for 1006 or 1005.
- Control valve 4205 120 8705, stamped 070/15, is replaced by 4205 120 8701, stamped 070/16. Drawing 328TI027 KN shows the previous valve on the left and new valve on the right. The new valve suits the higher trigger cut-off speed; limiting engine speed by enriching the mixture occurs only if the trigger unit fails. This is the described backup limiting function, not an instruction to defeat the trigger or a diagnostic proof of failure.
- The valve change renames HS 280 A to HS 280 B for TS 510 and HS 281 A to HS 281 B for TS 760. Carburetor order numbers remain 4205 120 0602 and 4205 120 0603 respectively. Summary rows 2–5 are paired old/new versions, not four different order numbers; each listed carburetor includes the corresponding control valve. The later 2012 IPL calls these numbers HS-280D / HS-281D: retain that later designation separately, not as proof that A, B and D are identical.
- If a faulty trigger 4205 400 1001 is replaced by 4205 400 1000, control valve 4205 120 8701 (070/16) must also be installed. This mandatory pairing does not erase the special 16-inch TS 760 exclusion. No reverse substitution, all-wheel conversion or independent approval of higher cutting speed is stated.
- Page 2 remark 1 retains the previous trigger for TS 760 with 16-inch cutting wheels. Remark 2 says only the modified carburetor version is available from the factory. Remark 3 permits the new control valve on older machines; that allowance belongs to the valve and is not unrestricted permission to change every trigger unit. These are 1999 availability/compatibility statements.
- Both original pages and their quiet regions were reviewed. The footer points to TI31/1997 as the last TI, not a delegated procedure. No additional manual is required by this bulletin, and no setting screw adjustment, torque, wheel compatibility approval or completed hardware test is supplied. Earlier source conflicts and dispositions remain unchanged.
Source: TI 32/1999, p. 1 · TI 32/1999, p. 2 — Section 1, both page 1 diagrams and complete page 2 summary/remarks.
Part numbers (6)
- 4205 400 1001 — Trigger unit, 8,400 RPM limitPrevious order number; retained for 16-inch TS 760 · TS 510 / TS 760; special 16-inch TS 760 excluded from trigger change
- 4205 400 1000 — Trigger unit, 9,200 RPM limitNew order number; paired valve required · TS 510 / TS 760 except special 16-inch TS 760
- 4205 120 8705 — Control valve, marking 070/15Previous control valve · HS 280 A / HS 281 A as described in TI32/1999
- 4205 120 8701 — Control valve, marking 070/16New valve; required with replacement trigger 4205 400 1000 · Stated TS 510 / TS 760 carburetors; also usable on older machines per remark 3
- 4205 120 0602 — Carburetor HS 280 A → HS 280 BOrder number unchanged across the stated A-to-B revision · TS 510
- 4205 120 0603 — Carburetor HS 281 A → HS 281 BOrder number unchanged across the stated A-to-B revision · TS 760
Wrong number or missing part for the TS 510, TS 760? Report a correction →