← Blowers & other equipment · series 4203

Stihl 4203 · Section B · 2 of 10 · 31 parts

Rewind starter, Muffler

Fits BR 320, BR 320 L, BR 400.

Parts diagrams →

Historical fitment & changes (5) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
110111213141516171819220212223242425262728293456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (31)

PosPart numberDescriptionQty
1 4223 195 0600 Starter cup Fitment / change note → 1
2 9210 261 1140 Hexagon nut M8x1 1
3 4203 190 0405 Starter cover with rewind starter 1
4 4203 190 0406 Starter cover 1
5 1110 084 9102 Bushing 1
6 9443 825 7130 Hollow rivet 7.5x1x6.8 3
7 0000 190 3401 Starter grip ElastoStart Ø 3.5 mm Fitment / change note → 1
8 1113 195 8200 Starter rope Ø 3.5x960 mm Fitment / change note → 1
9 0000 195 7001 Cap 1
10 1118 190 0600 Rewind spring 1
11 4119 195 0400 Rope rotor 1
12 4116 195 7200 Pawl 1
13 0000 958 0923 Washer 1
14 1118 195 3500 Spring 1
15 9022 371 1020 Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 3
16 4203 967 1500 Model plate BR 320 1
17 4203 967 1504 Model plate BR 320 L 1
18 4203 967 1501 Model plate BR 400 1
19 1115 149 0600 Muffler gasket 1
20 4203 140 0601 Muffler 1
21 4203 140 0602 NLA Muffler 1
22 4203 141 9005 NLA Screen 1
23 4203 141 6600 NLA Clip 1
24 9022 341 0980 Spline screw IS-M5x16 3
25 4203 140 0600 Muffler 1
26 9022 341 1190 Spline screw IS-M5x72 2
27 1121 195 3400 Starter grip 1
28 1128 190 2900 Starter rope Ø 3.5 mm Fitment / change note → 1
29 0000 958 0806 Washer 1
Not numbered on the diagram — assemblies, kits and options
— 0000 930 2203 Starter rope Ø 3.5 mm x 30.5 m option 1
— 0000 930 2267 Starter rope Ø 3.5 mm / 28 pieces 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · BR 320 / BR 400 / SR 320 / SR 400

BR 320 / BR 400 / SR 320 / SR 400: starter-cup replacement scope

Both original and modified starter cups are named as replacements; later blower and sprayer models are not inferred.

  • Starter cup 4116 195 0500 was modified during development of new models and renumbered 4223 195 0600. Introduction is IN PROGRESS; no numeric cutoff is given. New MOQ 10 is an order quantity, not ten installed cups. The old cup is no longer factory available, but the text explicitly retains its replacement suitability.
  • Both modified AND original cups should also be used as replacements for the printed scope “FS 160 through FS 280” and BR 320/400, SR 320/400. This is not every numeric FS model, every model sharing a part number, or proof of suitability for FS 290, FS 500/550, FR 220 or later successors. No dimensional change or installation torque is provided.
  • BR 320 L is present on the shared IPL sheet but is not separately named in this TI; it is not silently added to the model list.
  • Historical TI 48/1994 guidance, not current stock or verified physical interchange. Shared IPL sheets do not extend the named source models or variants. No hardware operation was performed.

Source: TI 48/1994, p. 4 — starter-cup replacement scope.

Part numbers (2)
  • 4116 195 0500 — Original starter cupalso suitable as described; no longer factory available · BR 320 / BR 400 / SR 320 / SR 400 only in the configuration described here
  • 4223 195 0600 — Modified starter cupMOQ 10; introduction in progress · BR 320 / BR 400 / SR 320 / SR 400 only in the configuration described here

Conditional replacement · FS 160 / FS 180 / FS 220 / FS 280 / FS 360 / FS 420 / BR 320 / BR 400 / SR 320 / SR 400

FS / BR / SR starter cup: old and new replacement scope

Modified cup 4223 195 0600 replaces 4116 195 0500; both versions are stated replacements for the additional named models.

  • In the cover scope FS160/180/220/280, starter cup 4116 195 0500 is modified during development of unspecified new models and renumbered 4223 195 0600. The TI explicitly says the modified cup AND THE ORIGINAL VERSION can ALSO be used as replacements for FS360, FS420, BR320/400 and SR320/400. It does not identify the new development models or authorize arbitrary starter-assembly interchange.
  • Introduction is IN PROGRESS; no serial marker is supplied for this change. The nameplate serial on the same page belongs to section 3, not this cup. New cup MOQ 10 is an order minimum. The ORIGINAL cup is NO LONGER AVAILABLE FROM THE FACTORY; historical replacement suitability does not promise continued supply.
  • Later exact-model rewind-starter sheets show 4223 195 0600 at key 1 for the 4119 and 4203 model groups and key 14 for FS360/420. Shared-sheet FS220 K, FS280 K, FS290, FS420 L and BR320 L are not silently added to this TI note. No cup dimensions or mounting torque are provided.
  • Historical TI guidance for the explicitly named models and stated versions only. Shared IPL sheets are navigation, not an extension to every listed variant or proof of unrestricted interchange. Supply statements are historical, not current stock guarantees. No hardware operation was performed.

Source: TI 16/1995, p. 3 · TI 16/1995, p. 4 — Section 4: starter-cup replacement scope, table and supply remark.

Part numbers (2)
  • 4116 195 0500 — Original starter cupreplacement suitability retained; no longer supplied · FS 160; FS 180; FS 220; FS 280; FS 360; FS 420; BR 320; BR 400; SR 320; SR 400
  • 4223 195 0600 — Modified starter cupnew; MOQ 10; explicitly stated replacement scope · FS 160; FS 180; FS 220; FS 280; FS 360; FS 420; BR 320; BR 400; SR 320; SR 400

Historical fitment · FS 550 / BR 320 / BR 400 / SR 320 / SR 400

FS 550 / BR-SR 320, 400: ElastoStart retrofit set

New 3.5 mm set replaces the older ElastoStart; no serial cutoff is printed for these models.

  • The TI expressly permits backfitting to its named models. First-time installation needs BOTH the appropriate grip and starter rope; no further changes to the rewind starter mechanism are required. This is not permission to mix rope diameters, omit the rope, or apply the change to every model using an old part number.
  • Summary items5–8 distinguish the previous ElastoStart 1128 190 3400 including rope1128 190 2900 from new grip0000 190 3401 including rope1113 195 8200. Both OLD rows carry remark1: remain available as spares. The old rope is specified only as diameter3.5 mm; do not assign the new rope length960 mm to it. New rope is diameter3.5 mm x960 mm (37.75 in).
  • The 020 T uses a different 3.0 mm x800 mm set. The part prefix does not determine model fitment. No reverse interchange or coil-spring internal substitution is stated.
  • Introduction is in progress for FS550 and BR/SR320,400. Do not copy the026 cutoff1 40 743 432 onto these machines. The summary states no separate cutoff for any of them.
  • Retained shared starter sheets list the new grip and rope. Their wider FS500/550L and BR320L headings do not extend TI41 scope. The derived TI43/1999 link to0000 190 3402 on BR/SR standard-grip rows was an019T-only assertion misapplied by part number;those unsupported links are removed. TI43 heading and section2 establish019T only,not BR/SR replacement.
  • Historical TI 41/1998 only: 020 T (series 1129), 026 (1121), FS 550 (4116), BR/SR 320 and 400 (4203). The original scan prints 1129 for 020 T; its extracted body truncates this to 112. Shared later catalog sheets do not extend this TI to 020/020 AV, 024, FS 500/550 L, BR 320 L, MS successors or other models. Availability is historical, not current stock. No hardware operation was performed.

Source: TI 41/1998, p. 1 · TI 41/1998, p. 3 — Introduction; larger-model summary items5–8 and in-progress changeover qualifier.

Referenced bulletin evidence: TI 43/1999, p. 1 · TI 43/1999, p. 2 — Page1 model019T/series1132 heading;page2 complete section2 ElastoStart and four-row summary,serial and spare remark only;remaining TI not semantically reviewed.

Part numbers (4)
  • 1128 190 3400 — Previous ElastoStart grip including original ropeOriginal remains spare · 026, FS 550, BR/SR 320,400
  • 1128 190 2900 — Previous starter rope, diameter3.5 mmOriginal remains spare · 026, FS 550, BR/SR 320,400
  • 0000 190 3401 — New ElastoStart grip including rope1113 195 8200New complete grip and rope · 026, FS 550, BR/SR 320,400
  • 1113 195 8200 — New starter rope, diameter3.5 mm x960 mm (37.75 in)New rope; included with grip · 026, FS 550, BR/SR 320,400

Service note · 020 T / 026 / FS 550 / BR 320 / BR 400 / SR 320 / SR 400

ElastoStart: spring action and complete-grip servicing

The internal spring smooths compression peaks; the TI limits repairs to grip and rope replacement.

  • Figures000TI028 KN and000TI029 KN identify grip1,cap2,sleeve3,coil spring4,two washers5 and rope6. In the idle position the sleeve,spring and washers are inside the grip. During pulling the force path is grip → lower washer → coil spring → upper washer → sleeve → rope.
  • The TI describes rising spring tension with compression pressure and nearly uniform grip force after the first compression stroke. Graph000TI007 KN compares ElastoStart with the standard grip without numerical axes or units; it does not establish a measured percentage reduction or starting-speed specification.
  • When pull exceeds the spring-defined limit,the spring becomes fully compressed and force passes directly from grip to rope. No numerical spring load or test specification is given. The grip spring is not the separate rewind spring in the starter housing.
  • The historical service note supplies the ElastoStart grip only as a complete replacement unit and limits repairs to grip and starter rope. The sectional drawings explain operation; they do not authorize internal spring/sleeve/washer repair. Later catalog sheets list a cap separately,which must not silently rewrite this1998 supply statement; its later supply context remains distinct.
  • Historical TI 41/1998 only: 020 T (series 1129), 026 (1121), FS 550 (4116), BR/SR 320 and 400 (4203). The original scan prints 1129 for 020 T; its extracted body truncates this to 112. Shared later catalog sheets do not extend this TI to 020/020 AV, 024, FS 500/550 L, BR 320 L, MS successors or other models. Availability is historical, not current stock. No hardware operation was performed.

Source: TI 41/1998, p. 1 · TI 41/1998, p. 2 — Full construction,unscaled comparison graph,operation and service-repair restriction.

No additional parts-table entry added.

Service note · 020 T / 026 / FS 550 / BR 320 / BR 400 / SR 320 / SR 400

ElastoStart: rope knots and 4–7 mm end allowance

The grip uses a simple overhand knot; complete rewind-starter work still depends on the model owner manual.

Model-specific manual evidence: 020 T: starter baseline and ElastoStart knot distinction · 026: six clockwise starter turns, not seven · FS 550: seven counterclockwise starter turns

  • The TI expressly permits backfitting to its named models. First-time installation needs BOTH the appropriate grip and starter rope; no further changes to the rewind starter mechanism are required. This is not permission to mix rope diameters, omit the rope, or apply the change to every model using an old part number.
  • Page2 figure000TI030 KN and all three installation bullets: thread the starter rope through the starter-housing rope-guide bushing FROM OUTSIDE; thread it through the rope rotor and secure it with a simple overhand knot. The TI then says the procedure is as before; it does not supply the full model-specific rotor/spring service sequence.
  • Page3 figure000TI031 KN and all seven replacement bullets: ease the cap from the grip; remove the remaining rope from grip and rotor; fit the ElastoStart rope as the standard rope but secure it IN THE GRIP with a SIMPLE overhand knot. Leave rope end a = 4–7 mm (about1/4 in),pull the knot into the grip,and fit the cap until it snaps into position. The procedure is then as before. The tail allowance is not total rope length or spring preload.
  • The page3 service note says the owner may maintain the named-model rewind starter using the owner manual,and users must be informed of the changed ElastoStart rope procedure. Later exact020 T,026 and FS550 workshop baselines are reviewed in the linked notes,with different turn counts/directions retained. Exact1998 owner-manual editions,the delegated Standard Repairs/Troubleshooting handbook,and a BR/SR320,400 model-specific baseline remain documented local source gaps. LaterBR/SR340,420 and MS successors are not substitutes.
  • Use the model-specific rope set in the source summary. TI41 itself provides no spring preload count,rotor tension check or torque. Values in the linked later-manual notes are explicitly source/edition-bound,not TI specifications or universal ElastoStart settings. No energized or physical procedure was performed.
  • Historical TI 41/1998 only: 020 T (series 1129), 026 (1121), FS 550 (4116), BR/SR 320 and 400 (4203). The original scan prints 1129 for 020 T; its extracted body truncates this to 112. Shared later catalog sheets do not extend this TI to 020/020 AV, 024, FS 500/550 L, BR 320 L, MS successors or other models. Availability is historical, not current stock. No hardware operation was performed.

Source: TI 41/1998, p. 1 · TI 41/1998, p. 2 · TI 41/1998, p. 3 — First-installation requirement; complete installation/replacement bullets,figures000TI030/031 KN and owner-manual dependency.

No additional parts-table entry added.

Wrong number or missing part for the BR 320, BR 320 L, BR 400? Report a correction →