Stihl 1121 · Section H · 8 of 17 · 22 parts
Rewind starter
Fits 026.
Historical fitment & changes (6) — includes parts and conditions not shown on this drawing.
Parts (22)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1121 080 1812 | Fan housing Fitment / change note → | 1 |
| 2 | 0000 967 1500 | Nameplate STIHL Fitment / change note → | 1 |
| 3 | 0000 967 2035 | Nameplate STIHL Fitment / change note → | 1 |
| 4 | 1110 084 9102 | Bushing | 1 |
| 5 | 0000 958 0514 | Washer | 1 |
| 6 | 9416 868 5630 | Hollow rivet 5.5x0.5x6.8 | 4 |
| 7 | 1118 190 0600 | Rewind spring | 1 |
| 8 | 1118 195 0300 | Spring housing | 1 |
| 9 | 1125 195 0401 | Rope rotor | 1 |
| 10 | 1125 195 7200 | Pawl | 1 |
| 11 | 0000 958 0923 | Washer | 1 |
| 12 | 1118 195 3500 | Spring | 1 |
| 13 | 0000 190 3401 | Starter grip ElastoStart Ø 3.5 mm Fitment / change note → | 1 |
| 14 | 1113 195 8200 | Starter rope Ø 3.5x960 mm Fitment / change note → | 1 |
| 15 | 0000 195 7001 | Cap | 1 |
| 16 | 1121 195 3400 | Starter grip | 1 |
| 17 | 9022 313 0680 | Spline screw IS-M4x16 | 3 |
| 18 | 0000 958 0806 | Washer | 1 |
| 19 | 0000 974 1000 | Round head rivet 3x6 | 2 |
| 20 | 0000 967 2020 NLA | Nameplate STIHL | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 1121 080 2101 | Fan housing with rewind starter Fitment / change note → | 1 |
| — | 0000 930 2203 | Starter rope Ø 3.5 mm x 30.5 m option | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
IPL correction · 026
026: repair-kit number differs between prose and table
Page 3 prints 1121 900 9004; page 5 prints 1121 900 5004 for the new ElastoStart repair kit. Neither number is silently corrected.
- Both numbers are legible in the original scans, not merely an OCR mismatch. Page 3 calls the new repair kit 1121 900 9004; page 5 calls it 1121 900 5004 and names the old kit 1121 900 5002. This is an unresolved source conflict, not an established alias or a verified ordering recommendation.
- The page 5 repair-kit (ElastoStart) row includes item 1, the air filter. Do not replace that explicit inclusion with a guessed starter-only inventory or infer every kit component. Page 3 restricts the new repair kit to 026 with the new filter system; the old table entry remains a spare under remark 1.
- No correction source has been established. The conflicting assertion is retained and dispositioned, not resolved; no invented source gap is used to skip other locally actionable content.
Source: TI 31/1995, p. 3 · TI 31/1995, p. 5 — Section 1.4 final paragraph versus section 1.5 special-accessory table.
Part numbers (3)
- 1121 900 9004 — New repair kit, prose spellingConflicting source number · 026 with new filter system for the disputed new kit; no verified alias
- 1121 900 5004 — New repair kit (ElastoStart), table spellingConflicting source number · 026 with new filter system for the disputed new kit; no verified alias
- 1121 900 5002 — Repair kit (ElastoStart)Original table number · 026 with new filter system for the disputed new kit; no verified alias
Conditional replacement · 026 / MS 260
026 / MS 260: fan housing with neutral repair badge
A new housing can repair an 026 while preserving its shroud-mounted model identity.
- The round nameplate clips to the revised fan housing; the separate company logo formerly in that location is deleted from the new design. New fan-housing assembly 1121 080 2101 replaces 1121 080 2100; bare housing 1121 080 1812 replaces 1121 080 1808. Both previous housings are supplied only while factory stocks last.
- Replacement housings include an MS 260 badge and neutral STIHL-only badge 0000 967 1500. For an 026 that retains its model nameplate on the shroud, use the neutral badge; do not relabel the repaired saw MS 260 merely because of its housing.
- The 026 / MS 260 model nameplate changes from 1121 967 1512 to 1121 967 1507. Old model nameplate and company logo 0000 967 2035 remain available for older machines. The summary repeats the housing assembly/bare housing as items5–6 and26–27; these are not additional different housing numbers. Its badge roster includes market/model alternatives, not a requirement to fit every badge at once.
- Shared IPL sheets do not extend these changes to unnamed variants. Introduction is in progress; the TI gives no numerical serial cutoff. Availability is the historical 2001 factory statement, not current stock. Later catalog numbers do not replace the historical evidence or prove unrestricted interchangeability.
Source: TI 43/2001, p. 1 · TI 43/2001, p. 2 · TI 43/2001, p. 5 · TI 43/2001, p. 7 · TI 43/2001, p. 8 — Sections1,2.3,6 and summary rows5–11,26–27/remarks1–2.
Part numbers (8)
- 1121 080 2100 — Fan housing with starterPrevious; stocks only · Only the named model/configuration; see conditions
- 1121 080 2101 — Fan housing with starterNew · Only the named model/configuration; see conditions
- 1121 080 1808 — Fan housingPrevious; stocks only · Only the named model/configuration; see conditions
- 1121 080 1812 — Fan housingNew · Only the named model/configuration; see conditions
- 0000 967 2035 — Company logoDeleted from new design; old stock item retained · Only the named model/configuration; see conditions
- 1121 967 1512 — 026 nameplatePrevious; retained · Only the named model/configuration; see conditions
- 1121 967 1507 — MS 260 nameplateNew · Only the named model/configuration; see conditions
- 0000 967 1500 — Neutral STIHL nameplate026 repair badge · Only the named model/configuration; see conditions
Historical fitment · 026
026: ElastoStart change at serial 1 40 743 432
New grip 0000 190 3401 includes the 3.5 mm x960 mm rope; older machines may be backfitted.
1 40 743 432 — 026 ElastoStart production introduction only; not a cutoff for 020 T, FS 550 or BR/SR models, and not a retrofit eligibility limit
- The TI expressly permits backfitting to its named models. First-time installation needs BOTH the appropriate grip and starter rope; no further changes to the rewind starter mechanism are required. This is not permission to mix rope diameters, omit the rope, or apply the change to every model using an old part number.
- Summary items5–8 distinguish the previous ElastoStart 1128 190 3400 including rope1128 190 2900 from new grip0000 190 3401 including rope1113 195 8200. Both OLD rows carry remark1: remain available as spares. The old rope is specified only as diameter3.5 mm; do not assign the new rope length960 mm to it. New rope is diameter3.5 mm x960 mm (37.75 in).
- The 020 T uses a different 3.0 mm x800 mm set. The part prefix does not determine model fitment. No reverse interchange or coil-spring internal substitution is stated.
- The 026 production change starts at serial 1 40 743 432. This cutoff does not restrict the expressly allowed earlier-machine retrofit. Retained026 rewind-starter rows13/14 corroborate the new grip/rope, not the historical production date.
- A derived TI43/1999 suggestion on the retained026 standard-grip row incorrectly applied an019T-only change to026. Original TI43 heading and page2 section2 confirm019T/series1132 only: its0000 190 3402 set and serial2 43 983 640 do NOT establish026 fitment. The unsupported catalog link is removed;TI41 specifies0000 190 3401 for026. The019T source assertion remains valid and unchanged.
- Historical TI 41/1998 only: 020 T (series 1129), 026 (1121), FS 550 (4116), BR/SR 320 and 400 (4203). The original scan prints 1129 for 020 T; its extracted body truncates this to 112. Shared later catalog sheets do not extend this TI to 020/020 AV, 024, FS 500/550 L, BR 320 L, MS successors or other models. Availability is historical, not current stock. No hardware operation was performed.
Source: TI 41/1998, p. 1 · TI 41/1998, p. 3 — Introduction; summary items5–8,remark1 and model026-only serial line.
Referenced bulletin evidence: TI 43/1999, p. 1 · TI 43/1999, p. 2 — Page1 model019T/series1132 heading;page2 complete section2 ElastoStart and four-row summary,serial and spare remark only;remaining TI not semantically reviewed.
Part numbers (4)
- 1128 190 3400 — Previous ElastoStart grip including original ropeOriginal remains spare · 026, FS 550, BR/SR 320,400
- 1128 190 2900 — Previous starter rope, diameter3.5 mmOriginal remains spare · 026, FS 550, BR/SR 320,400
- 0000 190 3401 — New ElastoStart grip including rope1113 195 8200New complete grip and rope · 026, FS 550, BR/SR 320,400
- 1113 195 8200 — New starter rope, diameter3.5 mm x960 mm (37.75 in)New rope; included with grip · 026, FS 550, BR/SR 320,400
Service note · 020 T / 026 / FS 550 / BR 320 / BR 400 / SR 320 / SR 400
ElastoStart: spring action and complete-grip servicing
The internal spring smooths compression peaks; the TI limits repairs to grip and rope replacement.
- Figures000TI028 KN and000TI029 KN identify grip1,cap2,sleeve3,coil spring4,two washers5 and rope6. In the idle position the sleeve,spring and washers are inside the grip. During pulling the force path is grip → lower washer → coil spring → upper washer → sleeve → rope.
- The TI describes rising spring tension with compression pressure and nearly uniform grip force after the first compression stroke. Graph000TI007 KN compares ElastoStart with the standard grip without numerical axes or units; it does not establish a measured percentage reduction or starting-speed specification.
- When pull exceeds the spring-defined limit,the spring becomes fully compressed and force passes directly from grip to rope. No numerical spring load or test specification is given. The grip spring is not the separate rewind spring in the starter housing.
- The historical service note supplies the ElastoStart grip only as a complete replacement unit and limits repairs to grip and starter rope. The sectional drawings explain operation; they do not authorize internal spring/sleeve/washer repair. Later catalog sheets list a cap separately,which must not silently rewrite this1998 supply statement; its later supply context remains distinct.
- Historical TI 41/1998 only: 020 T (series 1129), 026 (1121), FS 550 (4116), BR/SR 320 and 400 (4203). The original scan prints 1129 for 020 T; its extracted body truncates this to 112. Shared later catalog sheets do not extend this TI to 020/020 AV, 024, FS 500/550 L, BR 320 L, MS successors or other models. Availability is historical, not current stock. No hardware operation was performed.
Source: TI 41/1998, p. 1 · TI 41/1998, p. 2 — Full construction,unscaled comparison graph,operation and service-repair restriction.
No additional parts-table entry added.
Service note · 020 T / 026 / FS 550 / BR 320 / BR 400 / SR 320 / SR 400
ElastoStart: rope knots and 4–7 mm end allowance
The grip uses a simple overhand knot; complete rewind-starter work still depends on the model owner manual.
Model-specific manual evidence: 020 T: starter baseline and ElastoStart knot distinction · 026: six clockwise starter turns, not seven · FS 550: seven counterclockwise starter turns
- The TI expressly permits backfitting to its named models. First-time installation needs BOTH the appropriate grip and starter rope; no further changes to the rewind starter mechanism are required. This is not permission to mix rope diameters, omit the rope, or apply the change to every model using an old part number.
- Page2 figure000TI030 KN and all three installation bullets: thread the starter rope through the starter-housing rope-guide bushing FROM OUTSIDE; thread it through the rope rotor and secure it with a simple overhand knot. The TI then says the procedure is as before; it does not supply the full model-specific rotor/spring service sequence.
- Page3 figure000TI031 KN and all seven replacement bullets: ease the cap from the grip; remove the remaining rope from grip and rotor; fit the ElastoStart rope as the standard rope but secure it IN THE GRIP with a SIMPLE overhand knot. Leave rope end a = 4–7 mm (about1/4 in),pull the knot into the grip,and fit the cap until it snaps into position. The procedure is then as before. The tail allowance is not total rope length or spring preload.
- The page3 service note says the owner may maintain the named-model rewind starter using the owner manual,and users must be informed of the changed ElastoStart rope procedure. Later exact020 T,026 and FS550 workshop baselines are reviewed in the linked notes,with different turn counts/directions retained. Exact1998 owner-manual editions,the delegated Standard Repairs/Troubleshooting handbook,and a BR/SR320,400 model-specific baseline remain documented local source gaps. LaterBR/SR340,420 and MS successors are not substitutes.
- Use the model-specific rope set in the source summary. TI41 itself provides no spring preload count,rotor tension check or torque. Values in the linked later-manual notes are explicitly source/edition-bound,not TI specifications or universal ElastoStart settings. No energized or physical procedure was performed.
- Historical TI 41/1998 only: 020 T (series 1129), 026 (1121), FS 550 (4116), BR/SR 320 and 400 (4203). The original scan prints 1129 for 020 T; its extracted body truncates this to 112. Shared later catalog sheets do not extend this TI to 020/020 AV, 024, FS 500/550 L, BR 320 L, MS successors or other models. Availability is historical, not current stock. No hardware operation was performed.
Source: TI 41/1998, p. 1 · TI 41/1998, p. 2 · TI 41/1998, p. 3 — First-installation requirement; complete installation/replacement bullets,figures000TI030/031 KN and owner-manual dependency.
No additional parts-table entry added.
Service note · 026
026: six clockwise starter turns, not seven
The 2004-08 manual supplies a 026-specific baseline and delegates rotor/ElastoStart work to a separate handbook.
- Later workshop evidence used to follow the TI41/1998 starter dependency, not proof of the exact owner-manual edition in use in1998. Match the actual model and starter configuration. This is a source-bound service reference, not a complete owner manual. No hardware operation was performed.
- RA_127_01_01_02, cover edition2004-08, printed39–41/PDF40–42. Its shared024/026 scope does not extend the1998 TI to024. The introduction calls for the matching IPL, later TIs and separate standard-repair handbooks; the safety page requires the owner-manual warnings and local rules for any running work, with fuel work outdoors and away from fire.
- The manual distinguishes dirt/pitch from cold-thickened spring lubricant: it describes a few drops of paraffin (kerosene) followed by repeated careful pull/rewind for the latter; dirt/pitch requires removing and cleaning the mechanism, taking special care with the spring. Parts are washed in paraffin or white spirit; rewind spring and starter post use STIHL special lubricant before assembly. This historical treatment is not a universal solvent recommendation.
- Section7.2.1 removes the fan housing and delegates rope-rotor removal to Standard Repairs, Troubleshooting. After removing the spring housing and broken pieces, a replacement comes in its housing with special lubricant; place it bottom-plate-up and engage the anchor on the housing lug. If it pops out, refit with about20 mm anchor-loop offset from the spring-housing edge, wind COUNTERCLOCKWISE from outside inward and use wooden block1108 893 4800. Check the inner loop is2 mm from the starter post. Rotor installation is also delegated. Spring installation direction is not the tensioning direction.
- Section7.2.2 specifies a rope loop and SIX full turns CLOCKWISE using the rope close to the rotor. Hold the rotor steady, pull out and straighten the rope, hold the grip to keep tension, then release the rotor and slowly let the rope rewind. The grip must seat firmly in the guide bush without drooping; the manual calls for one additional turn if it does not. At full rope extension the rotor must still turn at least another half turn before maximum spring tension. If not, hold the rotor and remove one rope turn. Do not overtension: the rewind spring can break. Refit the fan housing. This is not the020 T seven-turn specification or FS550 counterclockwise direction.
- Section7.3 explicitly directs026 ElastoStart rope work to Standard Repairs and Troubleshooting. Its standard-grip sequence removes the cap and old rope, threads through the underside, ties a simple overhand knot, pulls it into the grip and replaces the cap. For the complete replacement grip supplied with rope, remove the old rotor knot and rope, thread1113 195 8200 through the guide bush FROM OUTSIDE, then through the rotor side hole; tie a simple overhand knot and seat it in the recess. Install rotor, tension per7.2.2 and refit housing. TI41 supplies the ElastoStart grip-tail change; a standard-grip drawing alone is not the complete026 ElastoStart handbook.
- The separate Standard Repairs, Troubleshooting handbook and exact1998 owner-manual edition are not established in the retained local inventory. Rotor-removal/installation and ElastoStart details delegated to that handbook remain source gaps; another model manual is not substituted.
TI dependency: TI 41/1998, p. 1 · TI 41/1998, p. 2 · TI 41/1998, p. 3 — TI41 pages2–3 as-before starter dependency; later model-specific workshop evidence, not specifications printed in the TI.
Later manual evidence: 024, 026 workshop manual (2004-08), section Safety/introduction and7.1–7.3 (printed39–41), PDF pages 1, 2, 3, 40, 41, 42
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Wrong number or missing part for the 026? Report a correction →