Stihl 4223 · Section H · 8 of 22 · 46 parts
Carburetor HS-274E (24.2003)
Fits TS 400.
Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.
Parts (46)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4223 120 0600 | Carburetor HS-274E Fitment / change note → → replaced by 4223 120 0650 TI 4/1998 | 1 |
| 2 | 4223 121 0800 | End cover | 1 |
| 3 | 1106 122 7400 | Round head screw | 4 |
| 4 | 1110 129 1110 | Gasket | 1 |
| 5 | 1124 121 4800 | Pump diaphragm | 1 |
| 6 | 4221 121 7800 | Strainer | 1 |
| 7 | 4116 121 5100 | Inlet needle | 1 |
| 8 | 1124 121 5000 | Inlet control lever | 1 |
| 9 | 1110 121 9200 | Spindle | 1 |
| 10 | 1110 122 7801 | Oval head screw | 1 |
| 11 | 1124 122 3000 | Spring Fitment / change note → → replaced by 1124 122 3001 TI 34/1997 | 1 |
| 12 | 1115 121 0800 | End cover | 1 |
| 13 | 1110 122 7700 | Oval head screw | 4 |
| 14 | 1110 121 4700 | Metering diaphragm | 1 |
| 15 | 1110 129 0900 | Gasket | 1 |
| 16 | 1110 122 9410 | Plug | 1 |
| 17 | 4223 121 5400 | Valve jet Fitment / change note → | 1 |
| 18 | 4221 122 6200 | Idle speed adjustment screw | 1 |
| 19 | 4221 122 4200 | Ball | 1 |
| 20 | 4221 122 6801 | Low speed adjustment screw Fitment / change note → | 1 |
| 21 | 1110 122 3030 | Spring | 2 |
| 22 | 4223 122 3600 | Sealing ring | 2 |
| 23 | 4223 122 6700 | High speed adjustment screw | 1 |
| 25 | 4221 122 7100 | Screw | 1 |
| 27 | 4223 120 7200 | Choke shaft | 1 |
| 28 | 4223 121 2900 | Choke shutter | 1 |
| 29 | 1110 122 7400 | Round head screw | 1 |
| 30 | 4221 122 3605 | Sealing ring | 2 |
| 31 | 4221 121 9400 | Ring | 2 |
| 32 | 1110 122 9005 | E-clip | 2 |
| 33 | 4223 122 3000 | Spring | 1 |
| 34 | 4223 120 7101 | Throttle shaft with lever | 1 |
| 35 | 4223 122 3200 | Torsion spring | 1 |
| 36 | 4221 121 8600 | Washer | 1 |
| 37 | 1110 122 9005 | E-clip | 1 |
| 38 | 4223 121 3300 | Throttle shutter Fitment / change note → | 1 |
| 39 | 1110 122 7400 | Round head screw | 1 |
| 40 | 4223 121 3500 | Throttle lever | 1 |
| 41 | 4205 121 5600 | Fixed jet 0.64 Fitment / change note → | 1 |
| 50 | 1106 122 3005 | Spring Fitment / change note → | 1 |
| 51 | 4221 121 5400 | Valve jet Fitment / change note → | 1 |
| 52 | 4223 122 6800 | Low speed adjustment screw Fitment / change note → | 1 |
| 53 | 4205 121 5600 | Fixed jet 0.64 Fitment / change note → | 1 |
| 54 | 4223 121 5600 | Fixed jet 0.69 Fitment / change note → | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 1124 007 1060 | Set of carburetor parts | 1 |
| — | not sold separately | Carburetor HS-274D not available as a separate item | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Historical fitment · TS 400
TS 400: HS 274 A becomes B with revised throttle shutter
Carburetor 4223 120 0600 unchanged; shutter 4221 121 3300 → 4223 121 3300.
- Throttle shutter 4223 121 3300, described as “with a second disengagement”, is installed in carburetor 4223 120 0600 to improve running properties. The scan reads HS 274 B instead of HS 274 A, correcting garbled retained extraction. The phrase “second disengagement” is preserved; no guessed hole, notch geometry, diameter or drilling operation is substituted.
- The table retains complete-carburetor number 4223 120 0600 in BOTH columns and replaces original shutter 4221 121 3300 with 4223 121 3300. Other parts as before. Only modified carburetor HS 274 B is to be supplied ex factory in future (remark1); original shutter remains available FOR OTHER SERIES (remark2), not a blanket TS400 interchange approval.
- Modification is introduced CONTINUOUSLY, with no numeric serial. Section1 X 33 772 153 does not establish this carburetor cutoff. No mixture setting, throttle screw torque, measured performance or HS279/HS301 applicability is given.
- The current exact-number IPL sheet and row label 4223 120 0600 as HS-274E, not A/B. Historical A-to-B change is linked to that exact-number TS400 sheet while preserving the edition/designation difference. No HS274E-to-A/B equivalence, internal interchange, or inherited later supersession is asserted.
- Historical TI 13/1996 evidence for TS 400, type 4223; no successor or additional market-specific variant applicability inferred. No hardware operation was performed; availability and performance rationale are historical statements, not current stock or a measured repair result.
Source: TI 13/1996, p. 2 — TS 400: HS 274 A becomes B with revised throttle shutter.
Part numbers (3)
- 4223 120 0600 — Carburetor HS 274 A/Bsame number; modified B only in future · TS 400; TI13/1996 stated configuration
- 4221 121 3300 — Original throttle shutterretained for other series · TS 400; TI13/1996 stated configuration
- 4223 121 3300 — New throttle shuttersecond disengagement; original wording · TS 400; TI13/1996 stated configuration
Conditional replacement · TS 400
TS 400: HS274B, C and D share an assembly number, not identical internals
Two staged modifications begin with HS274C at X 38 434 327; the D-stage cutoff is unstated.
X 38 434 327 — HS274C first-stage introduction only, before the EPA carburetor; HS274D second-stage cutoff not stated. Not a whole-model production range or starter cutoff.
- Historical TI04/1998 for TS 400, type 4223 only. Later 2012 IPL sheets are navigation/comparison, not evidence that their later versions equal the 1998 configuration. No extension to Japan-specific carburetors, other cut-off machines or saws. Historical factory availability is not current stock. No hardware operation was performed.
- Until the EPA carburetor is introduced, assembly 4223 120 0600 changes from HS274B to HS274C (first stage), then HS274D (second stage). HS274C is introduced from X 38 434 327. Stage 1 improves part-throttle running; stage 2 standardizes with other series/carburetor types. There is NO separate HS274D serial cutoff here. Check the stamped type, not just the shared order number.
- Modifications row 1 control spring, B/C/D: 1124 122 3000 / 1106 122 3005 / 1124 122 3000. The spring returns to the B number at the D stage; this is not a permanent B-to-C supersession.
- Modifications row 2 fixed jet, B/C/D: 4223 121 5600 (0.69) / 4205 121 5600 (0.64) / 4205 121 5600 (0.64). Modifications row 3 low-speed screw: 4223 122 6800 / 4223 122 6800 / 4221 122 6801. Modifications row 4 valve jet: 4221 121 5400 / 4221 121 5400 / 4223 121 5400. Drawing 338TI015 GM uses these four callouts, not the summary numbering; bold numbers mark changes at each stage.
- ONLY the specified parts may be installed in HS274C, EXCEPT its low-speed screw 4223 122 6800 which is no longer available. The sentence does not identify an unrestricted alternative for C; do not automatically assign the D screw to C.
- HS274D spare parts may also be used for HS274B EXCEPT the 0.64 fixed jet 4205 121 5600. Retain the B 0.69 assignment; this is not blanket interchange for all three versions.
- Summary row 1 HS274B 4223 120 0600 includes items 2–5. Row 2 spring 1124 122 3000; row 3 jet 0.69 4223 121 5600; row 4 low screw 4223 122 6800; row 5 valve jet 4221 121 5400. These occupy original columns with new-column dashes.
- Summary row 6 HS274C 4223 120 0600 includes items 4,5,7,8. Row 7 spring 1106 122 3005; row 8 jet 0.64 4205 121 5600. Row 9 HS274D 4223 120 0600 includes items 2,8,10,11. Row 10 low screw 4221 122 6801; row 11 valve jet 4223 121 5400. Rows 6–11 occupy new columns with original-column dashes; this does not make all components interchangeable.
- Summary remark 1 marks all three complete carburetors and old low screw as no longer required as spares; use service/supply notes and section 1. Remark 2 keeps the other listed individual components available. COMPLETE replacement is HS279B with its new choke lever, even for older machines.
- The later IPL names 4223 120 0600 HS-274E and separately references HS-274D. This later naming does not erase the B/C/D staging, identify D introduction or extend these instructions to E.
Source: TI 4/1998, p. 3 — Section 2 stages, four-row modifications table, eleven-row summary and service notes.
Part numbers (9)
- 4223 120 0600 — HS274B/C/D complete carburetorShared number; identify actual type · TS 400; only the version and conditions stated here
- 1124 122 3000 — Control springB and D · TS 400; only the version and conditions stated here
- 1106 122 3005 — Control springC only in this table · TS 400; only the version and conditions stated here
- 4223 121 5600 — Fixed jet 0.69B · TS 400; only the version and conditions stated here
- 4205 121 5600 — Fixed jet 0.64C and D; excluded for B replacement · TS 400; only the version and conditions stated here
- 4223 122 6800 — Low-speed screwB/C original; unavailable · TS 400; only the version and conditions stated here
- 4221 122 6801 — Low-speed screwD · TS 400; only the version and conditions stated here
- 4221 121 5400 — Valve jetB/C · TS 400; only the version and conditions stated here
- 4223 121 5400 — Valve jetD · TS 400; only the version and conditions stated here
Wrong number or missing part for the TS 400? Report a correction →