← TS 400

Stihl 4223 · Section G · 7 of 22 · 37 parts

Ignition system

Fits TS 400.

Parts diagrams →

Historical fitment & changes (9) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11011121313141516171819220212223242525262728293303132333445667789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (37)

PosPart numberDescriptionQty
1 4223 400 1201 Flywheel 1
2 0000 955 0802 Collar nut M8x1 1
3 4223 400 1303 Ignition module 1
4 not sold separately Ignition module no longer available from factory 1
5 not sold separately Ignition lead 330 mm no longer available from factorynot available as a separate item 1
6 0000 989 1002 Grommet 1
7 9022 341 1019 Spline screw IS-M5x20 2
8 not sold separately Short circuit wire no longer available from factory 1
9 4223 440 3001 Wiring harness 1
10 not sold separately Ignition lead not available as a separate item 1
11 not sold separately Short circuit wire not available as a separate item 1
12 4223 080 0900 Air guide shroud 1
13 4223 701 3300 Cable clamp 2
14 4223 431 8300 Insert 1
15 4223 400 1200 Flywheel → replaced by 4223 400 1201 TI 2/2002 1
16 4223 400 1300 Ignition module Fitment / change note → → replaced by 4223 400 1302 TI 2/2002 1
17 not sold separately Ignition lead 370 mm not available as a separate item 1
18 0000 989 1010 Grommet 1
19 0000 448 1201 Lead retainer 1
20 9022 341 1019 Spline screw IS-M5x20 3
21 4223 440 1100 Short circuit wire 380 mm / 15'' Fitment / change note → 1
22 4223 084 1600 Cover 1
23 1128 405 1000 Spark plug boot 1
24 0000 998 0604 Torsion spring 1
25 9022 341 1280 Spline screw IS-M6x16 2
26 1125 790 9906 Annular buffer 1125/06 1
27 1121 790 9912 Annular buffer 1
28 1125 791 7306 Plug 1
29 1119 791 7306 Plug 1
30 4223 080 3100 Fan cover 1
31 9443 825 7130 Hollow rivet 7.5x1x6.8 4
32 9416 868 6630 Hollow rivet 6.5x0.5x6.8 4
33 9022 371 1020 Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 4
34 9291 021 0120 Washer 5.3 3
Not numbered on the diagram — assemblies, kits and options
— 4223 007 1015 Conversion kit Wiring harness 1
— 0000 405 0600 NLA Ignition lead 1 m not illustratedoption 1
— 0000 930 2251 Ignition lead 10 m Fitment / change note → not illustratedoption 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Historical fitment · TS 400

TS 400: series 4223 replacement ignition assignment

4223 400 1300 with flywheel 4221 400 1200; 370 mm ignition lead.

  • Printed series 4223. Use 4223 400 1300 with flywheel 4221 400 1200.
  • Printed ignition-lead length: 370 mm (14 9/16 in). Preserve both printed units.
  • TI01/1999 lists replacement combinations for the then-current machines, not every earlier configuration. Older machines are referred to Spare Parts for Previous Models in their own illustrated parts lists; no serial cutoff is supplied here.
  • Use only the listed ignition-module/flywheel combinations. The source warns that incorrect combinations can cause excessive RPM or running in reverse; sharing a module number does not make all flywheels interchangeable.
  • Universal replacement modules may differ from production modules in maker, shape and part number. The source describes installation/function compatibility within its assignments, not universal compatibility or a project hardware test.
  • Some replacement modules require shortening the ignition lead and/or short-circuit wire and crimping a different short-circuit connector. The table gives ignition-lead lengths only; it supplies neither a short-circuit-wire length nor a connector part number. Do not infer that every row needs modification.
  • Only the named models and printed series are covered. A shared IPL sheet does not extend this assignment to unnamed models or modern MS equivalents. This 1999 USA bulletin is historical guidance, not current availability.

Source: TI 1/1999, p. 1 · TI 1/1999, p. 3 — 1.1 general restrictions and 1.2.2 power-tool assignments.

Part numbers (2)
  • 4223 400 1300 — Replacement ignition moduleAssigned component · TS 400, printed series 4223, listed combination only
  • 4221 400 1200 — Assigned flywheelRequired pairing · TS 400, printed series 4223

Service note · TS 400

TS 400 ignition: air gap, timing and suppressed spark plugs

Timing is specified at 8000 rpm; the 370-mm lead is a separate length specification.

  • Transistorized contactless magneto ignition with integrated control unit and electronic speed limitation. Module/flywheel air gap 0.15–0.3 mm (0.006–0.012 in); timing 1.6–2.2 mm (0.063–0.087 in) BEFORE TDC AT 8000 rpm. The timing distance is piston travel, not degrees or the module air gap.
  • Suppressed spark plug alternatives Bosch WSR 6 F OR NGK BPMR 7 A; electrode gap 0.5 mm (0.02 in), thread M 14 x 1.25, threaded length 9.5 mm (0.37 in). Source prints heat-range value 200; do not interpret that as a universal cross-brand plug-number scale.
  • Ignition lead length 370 mm (14 5/8 in). Page 10 separately lists 10-m HTR bulk lead 0000 930 2251; the service-stock length does not replace this installed-length specification.
  • Historical TI guidance for the 1995 TS 400, type 4223. Later IPL sheets are exact-model navigation aids, not proof of identical later configuration or current tool availability. No hardware operation was performed.

Source: TI 37/1995, p. 7 · TI 37/1995, p. 10 — TS 400 ignition: air gap, timing and suppressed spark plugs.

Part numbers (1)
  • 0000 930 2251 — HTR ignition lead, 10-m stock; see page10 service accessoriessource-listed service tool or accessory · TS 400; TS 400 ignition: air gap, timing and suppressed spark plugs

Service note · TS 400

TS 400 DG screws: existing threads, torque wrench and adhesive

Re-engage the original thread; apply the footnotes only to their marked joints.

  • DG screws form a permanent thread on first installation. Source permits removal/refitting while specified torque is maintained and requires a TORQUE WRENCH; it is not an instruction to repeatedly cut new threads.
  • For a precut thread, insert screw and turn ANTICLOCKWISE until it drops slightly; then turn clockwise and tighten to specified torque. Cutting another thread weakens the joint.
  • Footnote 1 applies to the groove-headed IS-DG 4 x 14 STARTER-COVER screw: secure with Loctite 242/243. Footnote 2 applies to IS-M 5 x 20 IGNITION-MODULE/CRANKCASE screws: a WASHER MUST BE FITTED under the screw head. These requirements are not blanket instructions for all rows.
  • Adhesive-secured screws must be heated with HOT AIR before unscrewing; PARTICULAR CARE ON PLASTIC PARTS. No heating temperature is provided.
  • Historical TI guidance for the 1995 TS 400, type 4223. Later IPL sheets are exact-model navigation aids, not proof of identical later configuration or current tool availability. No hardware operation was performed.

Source: TI 37/1995, p. 7 · TI 37/1995, p. 8 · TI 37/1995, p. 9 — TS 400 DG screws: existing threads, torque wrench and adhesive.

No additional parts-table entry added.

Service note · TS 400

TS 400 tightening torques: crankcase, AV joints and rotating parts

Left-hand clutch and pulley threads retain their separate torque values.

  • All values in Nm. Socket-head IS-M 5 x 20: shroud/tank housing 6.0; crankcase left/right 10.0; fan cover/tank housing 6.0; starter cover/cast arm 6.0; cylinder/crankcase 10.0; ignition module/crankcase 8.0 WITH WASHER UNDER THE HEAD.
  • IS-M 5 x 25 support/handlebar/tank housing: 8.0. IS-M 6 x 16 AV element joints: cast arm/handlebar 6.0; tank housing/cast arm 6.0; tank housing/crankcase LEFT 6.0. Grub screw M 5 x 55 tank housing/carburetor: 4.0.
  • Collar nut M 8 x 1 flywheel: 30.0; hex nut M 8 x 1 starter wheel: 23.0; driver M 12 x 1 L clutch: 40.0; spark plug M 14 x 1.25: 27.5; hex nut M 10 L V-belt pulley/bearing: 37.5; decompression valve: 14.0. The L markings identify LEFT-HAND THREADS, not alternative metric pitch values. No decompression-valve thread size is printed.
  • This completes the continued table, not a universal torque chart. Use the named joint and the companion DG/adhesive precautions; no source ordering numbers are supplied by this table.
  • Historical TI guidance for the 1995 TS 400, type 4223. Later IPL sheets are exact-model navigation aids, not proof of identical later configuration or current tool availability. No hardware operation was performed.

Source: TI 37/1995, p. 8 — TS 400 tightening torques: crankcase, AV joints and rotating parts.

No additional parts-table entry added.

Service note · TS 400

TS 400 assembly tools: piston, flywheel and rope bush

The stand, piston supports and flywheel extractor are distinct tools.

  • Assembly stand 5910 890 3100 holds machine for repair. Extractor 1116 893 0800 removes flywheel. Assembly pin 1108 893 4700 assembles piston pin; strap retainer 0000 893 2600 tensions piston rings; wooden block 1108 893 4800 positions piston.
  • Assembly tool 10 5910 890 2210 inserts snap rings in piston boss; assembly tool 0000 890 2201 flares rope guide bush. The numeric tool 10 designation is not a count of ten tools.
  • Historical TI guidance for the 1995 TS 400, type 4223. Later IPL sheets are exact-model navigation aids, not proof of identical later configuration or current tool availability. No hardware operation was performed.

Source: TI 37/1995, p. 9 — TS 400 assembly tools: piston, flywheel and rope bush.

Part numbers (7)
  • 5910 890 3100 — Assembly standsource-listed service tool or accessory · TS 400; TS 400 assembly tools: piston, flywheel and rope bush
  • 1116 893 0800 — Flywheel extractorsource-listed service tool or accessory · TS 400; TS 400 assembly tools: piston, flywheel and rope bush
  • 1108 893 4700 — Piston-pin assembly pinsource-listed service tool or accessory · TS 400; TS 400 assembly tools: piston, flywheel and rope bush
  • 0000 893 2600 — Piston-ring strap retainersource-listed service tool or accessory · TS 400; TS 400 assembly tools: piston, flywheel and rope bush
  • 1108 893 4800 — Wooden piston assembly blocksource-listed service tool or accessory · TS 400; TS 400 assembly tools: piston, flywheel and rope bush
  • 5910 890 2210 — Assembly tool10 for piston snap ringssource-listed service tool or accessory · TS 400; TS 400 assembly tools: piston, flywheel and rope bush
  • 0000 890 2201 — Rope guide bush flaring toolsource-listed service tool or accessory · TS 400; TS 400 assembly tools: piston, flywheel and rope bush

Service note · TS 400

TS 400 test tools: pressure, vacuum and ignition gauge

The test flange and exhaust sealing plate have different roles.

  • Carburetor/crankcase tester 1106 850 2905 for leakage testing, listed with connector 0000 855 9200 and fuel line 1110 141 8600. Vacuum pump 0000 850 3501 tests crankcase leakage.
  • Sealing plate 0000 855 8106 closes exhaust outlet for leakage tests; test flange 1128 850 4200 is listed for leakage testing. No pressure/hold-time instructions are supplied by this tool roster itself.
  • Setting gauge 1111 890 6400 sets ignition-module/flywheel air gap. Crimping tool 5910 890 8210 fits connectors to electrical leads; neither tool is a replacement ignition component.
  • Historical TI guidance for the 1995 TS 400, type 4223. Later IPL sheets are exact-model navigation aids, not proof of identical later configuration or current tool availability. No hardware operation was performed.

Source: TI 37/1995, p. 9 — TS 400 test tools: pressure, vacuum and ignition gauge.

Part numbers (8)
  • 1106 850 2905 — Carburetor/crankcase testersource-listed service tool or accessory · TS 400; TS 400 test tools: pressure, vacuum and ignition gauge
  • 0000 855 9200 — Tester connectorsource-listed service tool or accessory · TS 400; TS 400 test tools: pressure, vacuum and ignition gauge
  • 1110 141 8600 — Tester fuel linesource-listed service tool or accessory · TS 400; TS 400 test tools: pressure, vacuum and ignition gauge
  • 0000 850 3501 — Crankcase vacuum pumpsource-listed service tool or accessory · TS 400; TS 400 test tools: pressure, vacuum and ignition gauge
  • 0000 855 8106 — Exhaust sealing platesource-listed service tool or accessory · TS 400; TS 400 test tools: pressure, vacuum and ignition gauge
  • 1128 850 4200 — Leakage-test flangesource-listed service tool or accessory · TS 400; TS 400 test tools: pressure, vacuum and ignition gauge
  • 1111 890 6400 — Ignition air-gap gaugesource-listed service tool or accessory · TS 400; TS 400 test tools: pressure, vacuum and ignition gauge
  • 5910 890 8210 — Electrical connector crimping toolsource-listed service tool or accessory · TS 400; TS 400 test tools: pressure, vacuum and ignition gauge

Service note · TS 400

TS 400 torque tools: two ranges and warning-device versions

0302 and 0312 include optical/acoustic warnings; DG screws require a torque wrench.

  • Size 13 insert 5910 893 5608 is for flywheel nut; size 17 insert 5910 893 5610 for starter-wheel nut. These sizes are not inferred from nut thread diameters.
  • Torque wrenches 5910 890 0301/02 cover 0.5–18 Nm; 5910 890 0311/12 cover 6–80 Nm. The slash shorthand expands to 0301 and 0302, and 0311 and 0312 respectively. ONLY versions 5910 890 0302 and 5910 890 0312 are identified as having an OPTICAL/ACOUSTIC WARNING DEVICE. Torque wrench use is mandatory for DG screws.
  • Insert 0812 542 2104, designation printed 1-5 x 120 x 6.3, is for socket-head screws with STAR-SHAPED RECESS. Tee-handle screwdriver 5910 890 2400, printed QI-5 x 150, is for HEX SOCKET-HEAD screws. Preserve those distinct recess descriptions; do not silently correct uncertain designation typography into another tool size.
  • Historical TI guidance for the 1995 TS 400, type 4223. Later IPL sheets are exact-model navigation aids, not proof of identical later configuration or current tool availability. No hardware operation was performed.

Source: TI 37/1995, p. 9 — TS 400 torque tools: two ranges and warning-device versions.

Part numbers (8)
  • 5910 893 5608 — Size13 flywheel nut insertsource-listed service tool or accessory · TS 400; TS 400 torque tools: two ranges and warning-device versions
  • 5910 893 5610 — Size17 starter-wheel nut insertsource-listed service tool or accessory · TS 400; TS 400 torque tools: two ranges and warning-device versions
  • 5910 890 0301 — Torque wrench 0.5–18 Nmsource-listed service tool or accessory · TS 400; TS 400 torque tools: two ranges and warning-device versions
  • 5910 890 0302 — Torque wrench 0.5–18 Nm, optical/acoustic warningsource-listed service tool or accessory · TS 400; TS 400 torque tools: two ranges and warning-device versions
  • 5910 890 0311 — Torque wrench 6–80 Nmsource-listed service tool or accessory · TS 400; TS 400 torque tools: two ranges and warning-device versions
  • 5910 890 0312 — Torque wrench 6–80 Nm, optical/acoustic warningsource-listed service tool or accessory · TS 400; TS 400 torque tools: two ranges and warning-device versions
  • 0812 542 2104 — Star-recess screw insertsource-listed service tool or accessory · TS 400; TS 400 torque tools: two ranges and warning-device versions
  • 5910 890 2400 — Hex socket tee-handle screwdriversource-listed service tool or accessory · TS 400; TS 400 torque tools: two ranges and warning-device versions

Service note · TS 400

TS 400 service accessories: grease, lead stock and gasket set

Bulk ignition lead is 10 metres; the installed lead specification is 370 mm.

  • Section 7.2 lists STIHL multi-purpose grease 0781 120 1109 for the HIGH-VOLTAGE ARBOR ON THE IGNITION MODULE. Do not generalize the stated grease use to every bearing or gasket.
  • HTR ignition lead 0000 930 2251 is 10-m stock; section 6.3 separately specifies installed ignition lead length 370 mm. Gasket set 4223 007 1050 and sealing panel 0457 281 4103 are also listed; no gasket contents or specific panel placement is printed.
  • Historical TI guidance for the 1995 TS 400, type 4223. Later IPL sheets are exact-model navigation aids, not proof of identical later configuration or current tool availability. No hardware operation was performed.

Source: TI 37/1995, p. 7 · TI 37/1995, p. 10 — TS 400 service accessories: grease, lead stock and gasket set.

Part numbers (4)
  • 0781 120 1109 — STIHL multi-purpose grease for ignition high-voltage arborsource-listed service tool or accessory · TS 400; TS 400 service accessories: grease, lead stock and gasket set
  • 0000 930 2251 — HTR ignition lead,10-m stocksource-listed service tool or accessory · TS 400; TS 400 service accessories: grease, lead stock and gasket set
  • 4223 007 1050 — Gasket setsource-listed service tool or accessory · TS 400; TS 400 service accessories: grease, lead stock and gasket set
  • 0457 281 4103 — Sealing panelsource-listed service tool or accessory · TS 400; TS 400 service accessories: grease, lead stock and gasket set

Historical fitment · TS 400

TS 400: complete short-circuit wire replaces on-site assembly

4223 440 1100 newly supplied complete; three former components retained for other series only.

X 33 772 153 — Section1 retainer/short-circuit-wire modification only; not shroud or carburetor changeover.

  • Short-circuit wire 4223 440 1100 is now available as a COMPLETE ASSEMBLY instead of individual parts, simplifying repair. Previously it was not available as a replacement assembly and had to be cut to length and made up on site (remark 2). This is not proof that the wire itself was absent from original machines.
  • The including list retains the component identities: lead 0751 010 1110 (10 m ROLL), round sleeve 0751 030 8490 (3.5 mm), terminal socket 0751 030 8958 (4.8-1), and shrink tubing 0751 010 7245. The roll length is stock length, not an installed-wire length or assembly content of ten metres.
  • Remark 3 keeps the former lead, sleeve and terminal socket available FOR OTHER SERIES; it does not promise continued TS 400 individual-component repair supply. Remark 4 says former shrink tubing is NO LONGER AVAILABLE ex factory. New-column symbols do not override these separate supply restrictions.
  • No finished-wire length, cut length, shrink length or crimp specification is supplied by this TI. The current IPL labels 4223 440 1100 as 380 mm / 15 inches; that later catalog dimension is not silently copied into this historical assembly-making procedure. Retainer engagement/orientation remains covered by the companion note.
  • Historical TI 13/1996 evidence for TS 400, type 4223; no successor or additional market-specific variant applicability inferred. No hardware operation was performed; availability and performance rationale are historical statements, not current stock or a measured repair result.

Source: TI 13/1996, p. 1 — TS 400: complete short-circuit wire replaces on-site assembly.

Part numbers (5)
  • 4223 440 1100 — Complete short-circuit wirenew complete replacement assembly · TS 400; TI13/1996 stated configuration
  • 0751 010 1110 — Lead, 10 m rollformer component retained for other series · TS 400; TI13/1996 stated configuration
  • 0751 030 8490 — Round sleeve 3.5 mmformer component retained for other series · TS 400; TI13/1996 stated configuration
  • 0751 030 8958 — Terminal socket 4.8-1former component retained for other series · TS 400; TI13/1996 stated configuration
  • 0751 010 7245 — Shrink tubingformer version no longer supplied · TS 400; TI13/1996 stated configuration

Wrong number or missing part for the TS 400? Report a correction →