← TS 400

Stihl 4223 · Section O · 14 of 22 · 45 parts

Support with guard

Fits TS 400.

Parts diagrams →

Historical fitment & changes (14) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
110111213141516171819220212223242526272829330313233343536445567889
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (45)

PosPart numberDescriptionQty
1 4238 700 8110 Guard Ø 300 mm / 12'' 1
2 4224 700 8103 NLA Guard Ø 350 mm / 14'' → replaced by 4224 700 8102 TI 43/2007 1
3 4205 791 3902 Support 1
4 9456 621 3600 Circlip 32x1.2 Fitment / change note → 2
5 9503 003 6440 Grooved ball bearing 6201-2RS Fitment / change note → → replaced by 9503 003 6420 TI 5/1994 2
6 0000 961 1206 Ring Fitment / change note → 1
7 4201 704 0504 Shaft Fitment / change note → 1
8 4201 706 9202 Washer Fitment / change note → 2
9 4221 706 8800 Rubber ring Fitment / change note → 1
10 4221 706 8801 Rubber ring Fitment / change note → 1
11 4223 700 2900 Adjusting lever Fitment / change note → 1
12 9022 341 0960 Spline screw IS-M5x12 Fitment / change note → → replaced by 9022 341 0980 TI 3/2006 4
13 4205 706 2903 Flange Fitment / change note → 1
14 4223 710 9500 Adjusting screw Fitment / change note →
15 0000 997 1303 Compression spring Fitment / change note →
16 0000 958 1212 Washer Fitment / change note → 1
17 4223 036 8600 Woodruff key 1
18 4201 700 2504 NLA V-belt pulley 1
19 9291 021 0200 Washer 10.5 Fitment / change note → 1
20 9211 260 1350 Hexagon nut M10x1 l/h thread Fitment / change note → 1
21 9450 721 2150 Circlip 20x1.2 Fitment / change note → 1
22 4201 708 8402 Hexagon head screw M10x18 Fitment / change note → 1
23 4201 708 3004 Thrust washer Ø 103 mm 1
24 4201 708 3014 Thrust washer Ø 103 mm 1
25 4205 708 3000 Thrust washer Ø 118 mm Fitment / change note → 1
26 4205 708 3010 Thrust washer Ø 118 mm Fitment / change note → 1
27 0000 708 4200 Shaft sleeve option 1
28 4223 700 8100 Guard Fitment / change note → 1
29 4201 708 8401 Hexagon head screw M8x42 Fitment / change note → 3
30 4201 790 6005 Limit stop Fitment / change note → 1
31 4201 790 9302 Rubber buffer Fitment / change note → 1
32 9041 216 1230 Pan head screw M6x8 Fitment / change note → 1
33 9062 319 1260 NLA Countersunk screw M6x12 Fitment / change note → 1
34 0000 967 3577 Instruction label 1
35 0000 967 3578 Instruction label 1
36 0000 967 3903 Instruction label 1
Not numbered on the diagram — assemblies, kits and options
— 4223 007 1005 Support with guard Ø 300 mm / 12'' Fitment / change note → 1
— 4223 007 1008 Support with guard Ø 300 mm / 12'' 1
— 4223 007 1016 Support with guard Ø 300 mm / 12'' 1
— 4223 007 1007 Support with guard Ø 300 mm / 12'' Fitment / change note → 1
— 4221 007 1005 NLA Support with guard Ø 350 mm / 14'' 1
— 4221 007 1009 Support with guard Ø 350 mm / 14'' 1
— 4221 007 1014 Support with guard Ø 350 mm / 14'' 1
— 4221 007 1008 Support with guard Ø 350 mm / 14'' 1
— 4221 007 1013 Support with guard Ø 350 mm / 14'' 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · TS 400

TS 400 aluminium guard: two lever positions and side water feed

Lever position preserves adjustment with inboard or outboard mounting.

  • The new cutting-wheel attachment uses an ALUMINIUM GUARD, contributing to low overall machine weight. Its adjusting lever can be fitted on the shroud in TWO POSITIONS, maintaining the full guard-adjustment range for both INBOARD AND OUTBOARD mounting.
  • The water attachment for wet cutting is mounted AT THE SIDE and secured to the HANDLEBAR to maintain a clear view of the kerf during freehand cutting. These are layout descriptions, not kit interchange or installation instructions.
  • Section3 directs kit numbers to section5, now covered by separate source-linked notes. Bearing/guard compatibility and water-attachment compatibility remain distinct; the layout paragraph itself supplies no kit numbers.
  • Historical TI guidance for the 1995 TS 400, type 4223, only. Later exact-model IPL sheets are navigation aids, not evidence that every later variant has the original configuration. No hardware operation was performed.

Source: TI 37/1995, p. 5 — TS 400 aluminium guard: two lever positions and side water feed.

No additional parts-table entry added.

Service note · TS 400

TS 400 cutting wheels: source-era approvals and material table

Existing approved wheel types are carried over; the material table is not universal wheel fitment.

  • Section 4 states that all cutting wheels APPROVED FOR TS 350, TS 360, TS 460, TS 510 AND TS 760 can also be used with TS 400. This is a 1995 approval statement, not permission to ignore a wheel's size, bore, speed rating, condition or current instructions; it does not make every wheel suitable for every listed material.
  • COMPOSITE wheel applications listed: asphalt, concrete, stone, ductile cast pipes, railway tracks and steel. DIAMOND applications listed: asphalt, concrete, stone (hard rock), abrasive concrete, green concrete, clay bricks and pipes. The blank opposite composite ductile cast/railway/steel entries does not equate them to diamond applications.
  • Diamond ASPHALT footnote 1 includes common building/road asphalt types and blends with aggregates, plus green concrete and screed topping. CONCRETE footnote 2 includes common building cast stones and light reinforced concrete. STONE footnote 3 includes natural stones of every hardness, including hardest-wear-class granite, cast stones and concrete. These are material categories, not printed wheel ordering numbers or tested universal suitability.
  • Historical TI guidance for the source-era named models only; no future-model compatibility or current stock guarantee. No hardware operation was performed.

Source: TI 37/1995, p. 5 · TI 37/1995, p. 6 — TS 400 cutting wheels: source-era approvals and material table.

No additional parts-table entry added.

Service note · TS 400

TS 400 300-mm guard kit: replacement and historical scope

4223 007 1005 replaces 4201 007 1035; the 350-mm aluminium kit is only announced.

  • New bearing-with-guard attachment kit, diameter 300 mm, 4223 007 1005 is introduced with TS 400 and replaces former 4201 007 1035. Source says the NEW BEARING-WITH-GUARD KIT can be used for ALL STIHL CUT-OFF SAWS. Preserve that broad source-era statement without inventing an exhaustive model list or applying it to future machines.
  • The 350-mm bearing-with-guard kit with aluminium guard is promised in the FORESEEABLE FUTURE; no ordering number or release date is given. This does not establish its immediate availability in April 1995 or substitute a later 350-mm kit from the 2012 IPL.
  • The broad compatibility statement concerns the bearing/guard kit, NOT the adjacent water attachment. No individual guard-only interchange, exact kit contents or numeric production cutoff is printed.
  • Historical TI guidance for the source-era named models only; no future-model compatibility or current stock guarantee. No hardware operation was performed.

Source: TI 37/1995, p. 6 — TS 400 300-mm guard kit: replacement and historical scope.

Part numbers (2)
  • 4223 007 1005 — Bearing with guard,300 mmnew kit · TS 400; TS 400 300-mm guard kit: replacement and historical scope
  • 4201 007 1035 — Former bearing-with-guard kitreplaced · TS 400; TS 400 300-mm guard kit: replacement and historical scope

Service note · TS 400

TS 400 tightening torques: crankcase, AV joints and rotating parts

Left-hand clutch and pulley threads retain their separate torque values.

  • All values in Nm. Socket-head IS-M 5 x 20: shroud/tank housing 6.0; crankcase left/right 10.0; fan cover/tank housing 6.0; starter cover/cast arm 6.0; cylinder/crankcase 10.0; ignition module/crankcase 8.0 WITH WASHER UNDER THE HEAD.
  • IS-M 5 x 25 support/handlebar/tank housing: 8.0. IS-M 6 x 16 AV element joints: cast arm/handlebar 6.0; tank housing/cast arm 6.0; tank housing/crankcase LEFT 6.0. Grub screw M 5 x 55 tank housing/carburetor: 4.0.
  • Collar nut M 8 x 1 flywheel: 30.0; hex nut M 8 x 1 starter wheel: 23.0; driver M 12 x 1 L clutch: 40.0; spark plug M 14 x 1.25: 27.5; hex nut M 10 L V-belt pulley/bearing: 37.5; decompression valve: 14.0. The L markings identify LEFT-HAND THREADS, not alternative metric pitch values. No decompression-valve thread size is printed.
  • This completes the continued table, not a universal torque chart. Use the named joint and the companion DG/adhesive precautions; no source ordering numbers are supplied by this table.
  • Historical TI guidance for the 1995 TS 400, type 4223. Later IPL sheets are exact-model navigation aids, not proof of identical later configuration or current tool availability. No hardware operation was performed.

Source: TI 37/1995, p. 8 — TS 400 tightening torques: crankcase, AV joints and rotating parts.

No additional parts-table entry added.

Service note · TS 400

TS 400 dimensions and supplied accessories: 300-mm configuration

Dimensions include the wheel; the conflicting weight specification excludes it.

  • Section 6.6 length WITH 300-mm (12-inch) cutting wheel: 740 mm (29 in); width WITH HANDLE: 300 mm (12 in); height TO HANDLE: 350 mm (14 in). Do not apply these dimensions to an unprinted 350-mm wheel configuration.
  • Section 6.5 weight 8.9 kg (19.6 lb) is without fuel, complete with 300-mm wheel attachment but WITHOUT THE CUTTING WHEEL; the conflicting cover value 18.6 lb remains in the separate introduction note. Weight and length use different wheel-presence conditions.
  • Section 6.7 lists combination wrench, LOCKING PIN and screwdriver with no part numbers. This generic locking-pin entry does NOT override page 9: ONLY locking strip 0000 893 5903 may lock the TS 400 crankshaft, and special-tool stop bolts damage the piston. Do not identify the unnamed accessory as a permitted piston stop.
  • Historical TI guidance for the 1995 TS 400, type 4223. Later IPL sheets are exact-model navigation aids, not proof of identical later configuration or current tool availability. No hardware operation was performed.

Source: TI 37/1995, p. 8 · TI 37/1995, p. 9 — TS 400 dimensions and supplied accessories: 300-mm configuration.

Part numbers (1)
  • 0000 893 5903 — Only permitted crankshaft locking strip in section7.1source-listed service tool or accessory · TS 400; TS 400 dimensions and supplied accessories: 300-mm configuration

Service note · TS 400

TS 400 seal and bearing tools: jaws and distinct drift pins

1119 and 4119 drift pins have different jobs despite their matching suffix.

  • Press sleeve 1127 893 2400 presses in rotary shaft seal; assembly sleeve 1122 893 4600 protects the CLUTCH-SIDE rotary shaft seal. Extractor 0000 890 4400 removes shaft seals, with jaws Nos 3.1+4 under 0000 893 3706 and jaws No 6 under 0000 893 3711. Do not turn jaw labels into quantities or assign an unprinted side to each jaw set.
  • Pliers A 10 0811 611 8200: OUTER circlip on thrust washer. Pliers C 19 0811 641 8380: INNER circlip in spindle bearing and crankshaft.
  • Drift pin 1119 893 7200 presses the NEEDLE SLEEVE into/out of the V-belt pulley. Distinct drift pin 4119 893 7200 forces out DEEP-GROOVE BALL BEARINGS in the spindle bearing. The first four digits must not be normalized as a typo.
  • Historical TI guidance for the 1995 TS 400, type 4223. Later IPL sheets are exact-model navigation aids, not proof of identical later configuration or current tool availability. No hardware operation was performed.

Source: TI 37/1995, p. 9 — TS 400 seal and bearing tools: jaws and distinct drift pins.

Part numbers (9)
  • 1127 893 2400 — Seal press sleevesource-listed service tool or accessory · TS 400; TS 400 seal and bearing tools: jaws and distinct drift pins
  • 1122 893 4600 — Clutch-side seal protection sleevesource-listed service tool or accessory · TS 400; TS 400 seal and bearing tools: jaws and distinct drift pins
  • 0000 890 4400 — Rotary shaft seal extractorsource-listed service tool or accessory · TS 400; TS 400 seal and bearing tools: jaws and distinct drift pins
  • 0000 893 3706 — Extractor jaws Nos3.1+4source-listed service tool or accessory · TS 400; TS 400 seal and bearing tools: jaws and distinct drift pins
  • 0000 893 3711 — Extractor jaws No6source-listed service tool or accessory · TS 400; TS 400 seal and bearing tools: jaws and distinct drift pins
  • 0811 611 8200 — Pliers A10, outer circlipsource-listed service tool or accessory · TS 400; TS 400 seal and bearing tools: jaws and distinct drift pins
  • 0811 641 8380 — Pliers C19, inner circlipsource-listed service tool or accessory · TS 400; TS 400 seal and bearing tools: jaws and distinct drift pins
  • 1119 893 7200 — Needle-sleeve drift pinsource-listed service tool or accessory · TS 400; TS 400 seal and bearing tools: jaws and distinct drift pins
  • 4119 893 7200 — Spindle-bearing drift pinsource-listed service tool or accessory · TS 400; TS 400 seal and bearing tools: jaws and distinct drift pins

Service note · TS 350 / TS 360 / TS 400 / TS 460

TS guard redesign: aluminium, rubber clamping and two handle positions

The 1995 redesign reduces attachment weight by a version-dependent 400–900 grams.

  • New aluminium guard uses RUBBER RINGS instead of beveled/Belleville spring washers for clamping. A RIVETED STEEL STRAP protects its interior from cutting debris; no separate strap number or field-riveting procedure is given.
  • Adjusting handle can be secured in TWO POSITIONS to retain full swivel range with INBOARD OR OUTBOARD mounting. No angular range is specified. Figures 330 TI 001 and 330 TI 002 distinguish former/new exploded assemblies; position numbers are identifiers, not quantities.
  • Attachment weight reduction is BETWEEN 400 AND 900 GRAMS (source prints 3/4–2 lbs), DEPENDING ON VERSION. This is not a universal machine dry-weight figure or an exact metric/imperial conversion. Source describes improved centre of gravity and freehand handling without measured performance data.
  • Introduction prose says immediate replacement for 300-mm attachments; summary says introduced CONTINUOUSLY. Neither supplies a machine serial cutoff. Do not turn the issue date into a production identification range.
  • Historical TI guidance for TS 350, TS 360, TS 400 and TS 460. Shared TS 350 AVE/TS 360 catalog navigation does not add TS 350 AVE to the explicit source model list. Later IPL sheets are navigation aids, not proof of unchanged configurations or current availability. No hardware operation was performed.

Source: TI 38/1995, p. 1 · TI 38/1995, p. 2 · TI 38/1995, p. 3 · TI 38/1995, p. 4 — TS guard redesign: aluminium, rubber clamping and two handle positions.

No additional parts-table entry added.

Service note · TS 350 / TS 360 / TS 400 / TS 460

TS 300-mm guard attachments: dry and wet kits have different contents

4223 007 1006 replaces the former attachment; 1007 adds the wet-cutting kit.

  • Former 300-mm/12-inch bearing-with-guard attachment 4201 007 1040 includes items 1,3–28,31–34. New dry attachment 4223 007 1006 includes items 1,3–8,13,14,17–21,25–28,31–39. These are ITEM RANGES, not part quantities.
  • New wet version 4223 007 1007 comprises 300-mm bearing-with-guard plus water attachment 4201 007 1038 (remark 2). Complete wet-kit components and drilling restrictions are deferred to section 2.1; this note does not establish those installation details.
  • Former 300-mm guard 4201 700 8103 becomes 4223 700 8110. Remark 1: former attachment 4201 007 1040 and former guard 4201 700 8103 remain available ONLY WHILE FACTORY STOCKS LAST. Historical supply statement, not present stock.
  • Source explicitly lists TS 350,360,400,460 for these universal attachments. V-BELT GUARD IS EXCLUDED from replacement attachment supply; matching machine-specific guard and fastening elements must be retained/provided separately. Factory-new machines already include their appropriate guard and fasteners.
  • Historical TI guidance for TS 350, TS 360, TS 400 and TS 460. Shared TS 350 AVE/TS 360 catalog navigation does not add TS 350 AVE to the explicit source model list. Later IPL sheets are navigation aids, not proof of unchanged configurations or current availability. No hardware operation was performed.

Source: TI 38/1995, p. 1 · TI 38/1995, p. 2 · TI 38/1995, p. 3 · TI 38/1995, p. 4 — TS 300-mm guard attachments: dry and wet kits have different contents.

Part numbers (6)
  • 4201 007 1040 — Former 300-mm attachmentsource-listed former or new guard component; see conditions · TS 300-mm guard attachments: dry and wet kits have different contents
  • 4223 007 1006 — New 300-mm dry attachmentsource-listed former or new guard component; see conditions · TS 300-mm guard attachments: dry and wet kits have different contents
  • 4223 007 1007 — New 300-mm attachment with wet-cutting kitsource-listed former or new guard component; see conditions · TS 300-mm guard attachments: dry and wet kits have different contents
  • 4201 007 1038 — Wet-cutting kit included with 1007source-listed former or new guard component; see conditions · TS 300-mm guard attachments: dry and wet kits have different contents
  • 4201 700 8103 — Former 300-mm guardsource-listed former or new guard component; see conditions · TS 300-mm guard attachments: dry and wet kits have different contents
  • 4223 700 8110 — New 300-mm aluminium guardsource-listed former or new guard component; see conditions · TS 300-mm guard attachments: dry and wet kits have different contents

Service note · TS 350 / TS 360 / TS 400 / TS 460

TS 350-mm guard: future version announced without ordering numbers

Former 350-mm parts remain current until the announced successor becomes available.

  • Former 350-mm/14-inch attachment 4205 007 1040 includes items 2–26,29–34; former guard 4205 700 8100 remains current until the new version is available, expected AROUND MARCH 1996. This is a source-era forecast, not verified actual release timing.
  • New 350-mm attachment and guard ordering numbers are NOT GIVEN: table prints -*- and remark 4 promises a later Technical Information. No substitute number is inferred from 300-mm parts. Future attachment scope is items 2–8,13,14,17–21,25–28,31–39.
  • The locally reviewable announcement is captured; identifying the actual successor requires the later TI, to be sought in the retained queue. The absent future numbers do not make the remaining unreviewed local sections a source gap.
  • Historical TI guidance for TS 350, TS 360, TS 400 and TS 460. Shared TS 350 AVE/TS 360 catalog navigation does not add TS 350 AVE to the explicit source model list. Later IPL sheets are navigation aids, not proof of unchanged configurations or current availability. No hardware operation was performed.

Source: TI 38/1995, p. 1 · TI 38/1995, p. 3 · TI 38/1995, p. 4 — TS 350-mm guard: future version announced without ordering numbers.

Part numbers (2)
  • 4205 007 1040 — Former 350-mm attachment; current pending successorsource-listed former or new guard component; see conditions · TS 350-mm guard: future version announced without ordering numbers
  • 4205 700 8100 — Former 350-mm guard; current pending successorsource-listed former or new guard component; see conditions · TS 350-mm guard: future version announced without ordering numbers

Service note · TS 350 / TS 360 / TS 400 / TS 460

TS guard thrust washers: 100-mm pair replaces 118-mm design

Smaller washers also apply to future 350-mm attachments; source states 125-mm cutting depth.

  • 100-mm/3.9-inch thrust washers 4201 708 3003 (item 27) and 4201 708 3013 (item 28) continue in the new design. Former 118-mm/4.6-inch washers 4205 708 3000 (item 29) and 4205 708 3010 (item 30) are omitted from new attachment supply.
  • Source says 100-mm washers will be used EVEN ON 350-mm attachments, increasing maximum cutting depth to 125 mm(4.9 in). Do not assert 125 mm depth for every 300-mm wheel or treat washer diameter as wheel diameter.
  • Remark 5 explicitly keeps BOTH former 118-mm washers available. Omission from the new kit is NOT withdrawal from replacement supply, nor proof that an isolated washer swap converts every old assembly.
  • Historical TI guidance for TS 350, TS 360, TS 400 and TS 460. Shared TS 350 AVE/TS 360 catalog navigation does not add TS 350 AVE to the explicit source model list. Later IPL sheets are navigation aids, not proof of unchanged configurations or current availability. No hardware operation was performed.

Source: TI 38/1995, p. 1 · TI 38/1995, p. 2 · TI 38/1995, p. 4 — TS guard thrust washers: 100-mm pair replaces 118-mm design.

Part numbers (4)
  • 4201 708 3003 — Item 27 thrust washer 100 mmsource-listed former or new guard component; see conditions · TS guard thrust washers: 100-mm pair replaces 118-mm design
  • 4201 708 3013 — Item 28 thrust washer 100 mmsource-listed former or new guard component; see conditions · TS guard thrust washers: 100-mm pair replaces 118-mm design
  • 4205 708 3000 — Former item 29 thrust washer 118 mm; remains availablesource-listed former or new guard component; see conditions · TS guard thrust washers: 100-mm pair replaces 118-mm design
  • 4205 708 3010 — Former item 30 thrust washer 118 mm; remains availablesource-listed former or new guard component; see conditions · TS guard thrust washers: 100-mm pair replaces 118-mm design

Service note · TS 350 / TS 360 / TS 400 / TS 460

TS guard clamping: new rubber rings, lever and tensioning screw

Former parts retained for service are distinguished from parts merely omitted from the new kit.

  • Former items 9 rubber washer 4201 706 9201,10 rubber ring 4201 706 8801,11 flange 4205 706 2900 and 12 flat-head screwM 4 x 12 9079 346 0660 disappear from new-kit column but REMAIN AVAILABLE under remark 5.
  • Item 13 adjusting lever 4201 706 2600 becomes 4223 700 2900; former lever also REMAINS AVAILABLE (remark 5). Item 15 flat-head screwM 6 x 20 9086 216 1320 and item 16 Belleville washer 9486 648 1010 are omitted from new column WITHOUT a supply-status footnote; do not declare them unavailable.
  • New item 35 rubber ring 4221 706 8800 and item 36 rubber ring 4221 706 8801 are DISTINCT. Item 37 hexagon-socket screwM 5 x 12 9022 341 0960; item 38 tensioning screw 4223 710 9500 INCLUDES item 39 spring 0000 997 1303. No torque or universal standalone interchange is stated.
  • Exploded figures show the new rings at the guard hub and revised lever mounting. Do not identify new 4221-series rings with former 4201-series ring solely from a matching suffix.
  • Historical TI guidance for TS 350, TS 360, TS 400 and TS 460. Shared TS 350 AVE/TS 360 catalog navigation does not add TS 350 AVE to the explicit source model list. Later IPL sheets are navigation aids, not proof of unchanged configurations or current availability. No hardware operation was performed.

Source: TI 38/1995, p. 2 · TI 38/1995, p. 3 · TI 38/1995, p. 4 — TS guard clamping: new rubber rings, lever and tensioning screw.

Part numbers (13)
  • 4201 706 9201 — Former rubber washer, item 9source-listed former or new guard component; see conditions · TS guard clamping: new rubber rings, lever and tensioning screw
  • 4201 706 8801 — Former rubber ring, item 10source-listed former or new guard component; see conditions · TS guard clamping: new rubber rings, lever and tensioning screw
  • 4205 706 2900 — Former flange, item 11source-listed former or new guard component; see conditions · TS guard clamping: new rubber rings, lever and tensioning screw
  • 9079 346 0660 — FormerM 4 x 12 screw, item 12source-listed former or new guard component; see conditions · TS guard clamping: new rubber rings, lever and tensioning screw
  • 4201 706 2600 — Former adjusting lever, item 13source-listed former or new guard component; see conditions · TS guard clamping: new rubber rings, lever and tensioning screw
  • 4223 700 2900 — New adjusting lever, item 13source-listed former or new guard component; see conditions · TS guard clamping: new rubber rings, lever and tensioning screw
  • 9086 216 1320 — FormerM 6 x 20 screw, item 15source-listed former or new guard component; see conditions · TS guard clamping: new rubber rings, lever and tensioning screw
  • 9486 648 1010 — Former Belleville washer, item 16source-listed former or new guard component; see conditions · TS guard clamping: new rubber rings, lever and tensioning screw
  • 4221 706 8800 — New rubber ring, item 35source-listed former or new guard component; see conditions · TS guard clamping: new rubber rings, lever and tensioning screw
  • 4221 706 8801 — New rubber ring, item 36source-listed former or new guard component; see conditions · TS guard clamping: new rubber rings, lever and tensioning screw
  • 9022 341 0960 — NewM 5 x 12 screw, item 37source-listed former or new guard component; see conditions · TS guard clamping: new rubber rings, lever and tensioning screw
  • 4223 710 9500 — Tensioning screw including spring, item 38source-listed former or new guard component; see conditions · TS guard clamping: new rubber rings, lever and tensioning screw
  • 0000 997 1303 — Spring, item 39source-listed former or new guard component; see conditions · TS guard clamping: new rubber rings, lever and tensioning screw

Service note · TS 350 / TS 360 / TS 400 / TS 460

TS guard bearing and drive core: unchanged numbers and left-hand nut

Unchanged table numbers do not prove unrestricted complete-assembly interchange.

  • Unchanged items 3–8: bearing 4205 791 3901; circlip 32 x 1.2 9456 621 3600; ball bearing 6201 9503 003 6440; ring 0000 961 1206; shaft 4201 704 0504; washer 4201 706 9202. Figure shows bearing item 5 at two locations; no inferred pack quantity.
  • Unchanged item 14 flange 4205 706 2903, item 17 washer 0000 958 1212, item 18 Woodruff key 4 x 5 9482 435 0800, item 19 V-belt pulley 4201 704 1000, item 20 washerA 10.5 9291 021 0200, item 21 nutM 10 x 1 LEFT-HAND 9211 260 1350. Thread handedness is explicit; no tightening torque printed.
  • Item 25 axial clamping ring 20 x 1.2 9450 721 2150 and item 26 hex boltM 10 x 18 4201 708 8402 remain unchanged. Table continuity concerns these named components, not unrestricted mixing of old/new clamping stacks.
  • Historical TI guidance for TS 350, TS 360, TS 400 and TS 460. Shared TS 350 AVE/TS 360 catalog navigation does not add TS 350 AVE to the explicit source model list. Later IPL sheets are navigation aids, not proof of unchanged configurations or current availability. No hardware operation was performed.

Source: TI 38/1995, p. 2 · TI 38/1995, p. 3 · TI 38/1995, p. 4 — TS guard bearing and drive core: unchanged numbers and left-hand nut.

Part numbers (14)
  • 4205 791 3901 — Bearing, item 3source-listed former or new guard component; see conditions · TS guard bearing and drive core: unchanged numbers and left-hand nut
  • 9456 621 3600 — Circlip 32 x 1.2, item 4source-listed former or new guard component; see conditions · TS guard bearing and drive core: unchanged numbers and left-hand nut
  • 9503 003 6440 — Ball bearing 6201, item 5source-listed former or new guard component; see conditions · TS guard bearing and drive core: unchanged numbers and left-hand nut
  • 0000 961 1206 — Ring, item 6source-listed former or new guard component; see conditions · TS guard bearing and drive core: unchanged numbers and left-hand nut
  • 4201 704 0504 — Shaft, item 7source-listed former or new guard component; see conditions · TS guard bearing and drive core: unchanged numbers and left-hand nut
  • 4201 706 9202 — Washer, item 8source-listed former or new guard component; see conditions · TS guard bearing and drive core: unchanged numbers and left-hand nut
  • 4205 706 2903 — Flange, item 14source-listed former or new guard component; see conditions · TS guard bearing and drive core: unchanged numbers and left-hand nut
  • 0000 958 1212 — Washer, item 17source-listed former or new guard component; see conditions · TS guard bearing and drive core: unchanged numbers and left-hand nut
  • 9482 435 0800 — Woodruff key 4 x 5, item 18source-listed former or new guard component; see conditions · TS guard bearing and drive core: unchanged numbers and left-hand nut
  • 4201 704 1000 — V-belt pulley, item 19source-listed former or new guard component; see conditions · TS guard bearing and drive core: unchanged numbers and left-hand nut
  • 9291 021 0200 — WasherA 10.5, item 20source-listed former or new guard component; see conditions · TS guard bearing and drive core: unchanged numbers and left-hand nut
  • 9211 260 1350 — LEFT-HAND nutM 10 x 1, item 21source-listed former or new guard component; see conditions · TS guard bearing and drive core: unchanged numbers and left-hand nut
  • 9450 721 2150 — Axial clamping ring 20 x 1.2, item 25source-listed former or new guard component; see conditions · TS guard bearing and drive core: unchanged numbers and left-hand nut
  • 4201 708 8402 — Hex boltM 10 x 18, item 26source-listed former or new guard component; see conditions · TS guard bearing and drive core: unchanged numbers and left-hand nut

Service note · TS 350 / TS 360 / TS 400 / TS 460

TS replacement guard attachments exclude V-belt covers and fasteners

Drawn items 22–24 and 40 are not supplied with the new attachments.

  • Item 22 guard 4201 700 8114, item 23 segment 4205 708 3201 and item 24 hex boltM 8 x 42 4201 708 8401 retain identical old/new numbers but carry remark 6: NOT INCLUDED in new attachment supply. New item 40 V-belt guard 4223 700 8100 likewise carries remark 6.
  • Page 1 identifies 4223 700 8100 with TS 400 introduction. Do not treat the two separately illustrated belt covers as equivalent or both required on every model. New factory machines include their correct cover and fastening elements; replacement bearing-with-guard kits omit them.
  • Item 41 ring 4201 704 7600, dimensions 1 inch x 20 mm x 9.5 mm, is unchanged and illustrated separately. It is NOT in the explicit old/new complete-attachment item ranges, which stop at 34/39 respectively. Do not infer its inclusion simply because it appears in the drawing.
  • Historical TI guidance for TS 350, TS 360, TS 400 and TS 460. Shared TS 350 AVE/TS 360 catalog navigation does not add TS 350 AVE to the explicit source model list. Later IPL sheets are navigation aids, not proof of unchanged configurations or current availability. No hardware operation was performed.

Source: TI 38/1995, p. 1 · TI 38/1995, p. 2 · TI 38/1995, p. 3 · TI 38/1995, p. 4 — TS replacement guard attachments exclude V-belt covers and fasteners.

Part numbers (5)
  • 4201 700 8114 — V-belt guard, item 22; excludedsource-listed former or new guard component; see conditions · TS replacement guard attachments exclude V-belt covers and fasteners
  • 4205 708 3201 — Segment, item 23; excludedsource-listed former or new guard component; see conditions · TS replacement guard attachments exclude V-belt covers and fasteners
  • 4201 708 8401 — Hex boltM 8 x 42, item 24; excludedsource-listed former or new guard component; see conditions · TS replacement guard attachments exclude V-belt covers and fasteners
  • 4223 700 8100 — TS 400 V-belt guard, item 40; excludedsource-listed former or new guard component; see conditions · TS replacement guard attachments exclude V-belt covers and fasteners
  • 4201 704 7600 — Ring 1 inch x 20 mm x 9.5 mm, item 41; not listed in kit rangessource-listed former or new guard component; see conditions · TS replacement guard attachments exclude V-belt covers and fasteners

Service note · TS 350 / TS 360 / TS 400 / TS 460

TS guard stop and buffer hardware: four unchanged components

Items 31–34 remain in both former and new attachment scopes.

  • Item 31 stop 4201 790 6005; item 32 rubber buffer 4201 790 9302; item 33 socket-head screwM 6 x 8 9041 216 1230; item 34 countersunk screwM 6 x 12 9062 319 1260. All retain the same old/new numbers and belong to both specified attachment scopes.
  • The two screws have different head forms and lengths. No torque, serial cutoff or blanket fitment beyond the named attachment scope is provided.
  • Historical TI guidance for TS 350, TS 360, TS 400 and TS 460. Shared TS 350 AVE/TS 360 catalog navigation does not add TS 350 AVE to the explicit source model list. Later IPL sheets are navigation aids, not proof of unchanged configurations or current availability. No hardware operation was performed.

Source: TI 38/1995, p. 2 · TI 38/1995, p. 3 · TI 38/1995, p. 4 — TS guard stop and buffer hardware: four unchanged components.

Part numbers (4)
  • 4201 790 6005 — Stop, item 31source-listed former or new guard component; see conditions · TS guard stop and buffer hardware: four unchanged components
  • 4201 790 9302 — Rubber buffer, item 32source-listed former or new guard component; see conditions · TS guard stop and buffer hardware: four unchanged components
  • 9041 216 1230 — Socket-headM 6 x 8 screw, item 33source-listed former or new guard component; see conditions · TS guard stop and buffer hardware: four unchanged components
  • 9062 319 1260 — CountersunkM 6 x 12 screw, item 34source-listed former or new guard component; see conditions · TS guard stop and buffer hardware: four unchanged components

Wrong number or missing part for the TS 400? Report a correction →