Stihl 4224 · Section K · 10 of 15 · 57 parts
Support with guard with water attachment
Fits TS 700.
Historical fitment & changes (9) — includes parts and conditions not shown on this drawing.
Parts (57)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4224 790 5301 | Support Fitment / change note → → replaced by 4224 700 8113 TI 6/2010 | 1 |
| 2 | 4224 791 3903 | Support Fitment / change note → → replaced by 4224 791 3901 TI 6/2010 | 1 |
| 3 | 4224 691 0200 | Limit stop Fitment / change note → | 1 |
| 4 | 9074 478 2967 | Pan head self-tapping screw IS-P4x10 Fitment / change note → | 1 |
| 5 | 4224 691 0100 | Stop pin Fitment / change note → | 1 |
| 6 | 4224 700 8108 | Guard Ø 350 mm / 14'' Fitment / change note → | 1 |
| 7 | 4224 700 8102 | Guard Ø 350 mm / 14'' Fitment / change note → | 1 |
| 8 | 4238 706 0400 | Stiffener | 2 |
| 9 | 9503 003 6440 | Grooved ball bearing 6201-2RS → replaced by 9503 003 6420 TI 5/1994 | 2 |
| 10 | 0000 961 1206 | Ring | 1 |
| 11 | 9456 621 3600 | Circlip 32x1.2 | 2 |
| 12 | 4224 704 0502 | Shaft | 1 |
| 13 | 4201 706 9202 | Washer | 2 |
| 14 | 4224 706 8802 | Rubber ring | 1 |
| 15 | 4224 706 8801 | Rubber ring | 1 |
| 16 | 4205 706 2903 | Flange | 1 |
| 17 | 4224 710 9501 | Adjusting screw | 1 |
| 18 | 0000 670 0207 | Banjo bolt | 1 |
| 19 | 9645 948 0340 | O-ring 6x1.5 | 1 |
| 20 | 9041 216 0630 | Pan head screw M4x8 | 2 |
| 21 | 0000 679 2000 | Gasket | 1 |
| 22 | 4224 708 8300 | Square nut | 2 |
| 23 | 0000 670 0206 | Banjo bolt | 1 |
| 24 | 4238 677 8202 | Connector | 1 |
| 25 | 9771 021 0921 | Hose clip 10/7 | 2 |
| 26 | 4238 677 8200 | Connector | 1 |
| 27 | 4224 700 6801 | Bracket | 1 |
| 28 | 4201 700 4500 | Shut-off cock 1/4" | 1 |
| 29 | 0000 954 1701 | Sealing ring | 1 |
| 30 | 4201 700 7300 | Hose connector | 1 |
| 31 | 9645 945 7506 | O-ring 10x3 | 1 |
| 32 | 4201 670 1700 | Coupling sleeve 1/2" | 1 |
| 33 | 4201 670 1701 | Coupling sleeve 3/4" | 1 |
| 34 | 9022 341 1070 | Spline screw IS-M5x30 | 1 |
| 35 | 4224 700 2901 | Adjusting lever | 1 |
| 36 | not sold separately | Hose 5.6x1.9x614 mm not available as a separate item | 1 |
| 37 | 4224 764 8503 | Poly V-belt pulley | 1 |
| 38 | 9291 021 0200 | Washer 10.5 | 1 |
| 39 | 9211 260 1350 | Hexagon nut M10x1 l/h thread | 1 |
| 40 | 4201 708 8402 | Hexagon head screw M10x18 | 1 |
| 41 | 9450 721 2150 | Circlip 20x1.2 | 1 |
| 42 | 4201 708 3004 | Thrust washer Ø 103 mm | 1 |
| 43 | 4201 708 3014 | Thrust washer Ø 103 mm | 1 |
| 44 | 4205 708 3000 | Thrust washer Ø 118 mm | 1 |
| 45 | 4205 708 3010 | Thrust washer Ø 118 mm | 1 |
| 46 | 9022 341 1220 | Spline screw IS-M5x48 | 1 |
| 47 | 4224 700 8113 | Guard Fitment / change note → | 1 |
| 48 | 4224 700 8100 | Guard Fitment / change note → | 1 |
| 49 | 4224 708 8400 | Screw Fitment / change note → | 3 |
| 50 | 4224 790 9300 | Rubber buffer Fitment / change note → | 1 |
| 51 | 9022 341 0910 | Spline screw IS-M5x6 Fitment / change note → | 1 |
| 52 | 0000 960 0101 | Set of instruction labels Fitment / change note → | 1 |
| 53 | 0000 960 0101 | Set of instruction labels Fitment / change note → | 1 |
| 54 | 0000 967 3903 | Instruction label | 1 |
| 55 | 4238 967 3701 NLA | Instruction label | 1 |
| 56 | 0000 967 7226 | Warning pictogram | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 0000 937 4049 | Hose 5.6x1.9 mm x 1 m not illustratedoption | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · TS 700
TS 700: support changes occur in two distinct stages
Older-machine use of 3903 does not authorize mixing later captive-nut components.
- Sections 1.1/1.2 are TS 700 ONLY: stop pin in the cast arm and molded guard lugs define the inboard and outboard adjustment ranges. No numerical angle is given. Support 4224 791 3900 is replaced by 4224 791 3903, adding a threaded stop-pin hole and extra limit-stop fastening holes.
- The previous 3900 support is no longer available; 3903 can also be used on older machines with 3900. Summary row 1 carries remarks 1/2. This is the first, defined-adjustment-range stage, not blanket compatibility of every later support.
- Section 3.1 then replaces 3903 by 4224 790 5301 for the captive-nut belt guard. At that second stage 3903 remains available for older machines and old support/guard/screws MUST NOT be combined with new support/guard. The same bulletin thus calls 3903 new in section 1 and previous in section 3; preserve both stages.
- The retained older TS 700 L sheet carries 3903 with guard 4224 700 8103; the TI explicitly discusses 8102/8108. A shared support number does not extend the new-guard service procedure to the unmentioned 8103 guard.
- Historical English TI06/2010, series 4224. Modification introduced continuously; no numeric serial cutoff is supplied. Availability statements describe 2010, not current stock. No physical interchange test was performed.
Source: TI 6/2010, p. 1 · TI 6/2010, p. 2 · TI 6/2010, p. 10 · TI 6/2010, p. 11 · TI 6/2010, p. 12 — support changes occur in two distinct stages.
Part numbers (3)
- 4224 791 3900 — Support without new stop featuresPrevious; discontinued · TS 700; retain the specified guard and fastening generation
- 4224 791 3903 — Support with stop-pin thread and limit-stop holesFirst-stage replacement; retained for older fastening generation · TS 700; retain the specified guard and fastening generation
- 4224 790 5301 — Support with studsSecond-stage replacement; matched captive-nut guard required · TS 700; retain the specified guard and fastening generation
Service note · TS 700
TS 700: 350 mm guards retain an explicit old/new restriction
The scanned service note is restrictive, not permission for a universal retrofit.
- Section 1.3 replaces guard diameter 350 mm 4224 700 8102 with 4224 700 8108. New molded lugs work with the stop pin to define adjustment travel. Old 8102 remains available for older machines; summary row 2 carries remarks 3/4, NOT older-machine retrofit remark 2.
- The original service note says 8102 may ONLY be installed in machines with the previous guard and 8108 may ONLY be installed in machines with the new guard. Retain this literal restriction; it does not identify a serial breakpoint or authorize converting every older machine to the new guard.
- Unresolved wording: section 1.3 says stop pins installed into the guard, but sections 1.1/1.2/1.4 and drawings locate the pin in the SUPPORT. Section 1.2 also calls previous support 3900 a stop in its spare-parts paragraph. These are source wording inconsistencies, not evidence for a second pin location or a different part. Do not silently rewrite the original.
- Inboard and outboard configurations have different illustrated travel. Both require the specified stop-pin limitation; no degree range is reconstructed from the illustration.
- Historical English TI06/2010, series 4224. Modification introduced continuously; no numeric serial cutoff is supplied. Availability statements describe 2010, not current stock. No physical interchange test was performed.
Source: TI 6/2010, p. 1 · TI 6/2010, p. 2 · TI 6/2010, p. 11 · TI 6/2010, p. 12 — 350 mm guards retain an explicit old/new restriction.
Part numbers (2)
- 4224 700 8102 — Guard diameter 350 mm, previous versionRetained; previous-guard machines only · TS 700; retain the specified guard and fastening generation
- 4224 700 8108 — Guard diameter 350 mm with molded lugsNew-guard machines only · TS 700; retain the specified guard and fastening generation
Service note · TS 700
TS 700: new stop pin and limit stop have different torques
Stop pin is 5 Nm; limit-stop attachment is 1.5 Nm.
- Sections 1.4/1.5 introduce stop pin 4224 691 0100 and limit stop 4224 691 0200 with the new guard. Pin installs in the support; pin and molded guard lugs determine travel. Tighten stop pin / support to 5 Nm.
- Attach limit stop to support using new pan-head self-tapping screw IS-P4x10, 9074 478 2967. Limit stop / support torque is 1.5 Nm. Summary rows 3–5 have no previous part number; do not invent supersessions.
- The figures identify these two distinct fasteners and locations. The values are not generic V-belt guard, banjo-bolt or wheel-attachment torques.
- Historical English TI06/2010, series 4224. Modification introduced continuously; no numeric serial cutoff is supplied. Availability statements describe 2010, not current stock. No physical interchange test was performed.
Source: TI 6/2010, p. 3 · TI 6/2010, p. 11 · TI 6/2010, p. 12 — new stop pin and limit stop have different torques.
Part numbers (3)
- 4224 691 0100 — Stop pinIntroduced; 5 Nm at support · TS 700; retain the specified guard and fastening generation
- 4224 691 0200 — Limit stopIntroduced; attachment 1.5 Nm · TS 700; retain the specified guard and fastening generation
- 9074 478 2967 — Pan-head self-tapping screw IS-P4x10Introduced; limit-stop attachment · TS 700; retain the specified guard and fastening generation
Service note · TS 700
TS 700: old rubber buffer and screw remain for older machines
Elimination with the new stop system is not a universal removal instruction.
- Section 1.6 eliminates rubber buffer 4224 790 9300 and spline screw IS-M5x6-10.9, 9022 341 0910, when the new support-mounted pin and guard lugs determine travel.
- Both old parts remain available for older machines; summary rows 9/10 carry remark 3 and blank new-number cells. Do not delete them from old configurations or infer either part is individually replaced by the new pin.
- Historical English TI06/2010, series 4224. Modification introduced continuously; no numeric serial cutoff is supplied. Availability statements describe 2010, not current stock. No physical interchange test was performed.
Source: TI 6/2010, p. 3 · TI 6/2010, p. 11 · TI 6/2010, p. 12 — old rubber buffer and screw remain for older machines.
Part numbers (2)
- 4224 790 9300 — Rubber bufferEliminated in new system; retained for older machines · TS 700; retain the specified guard and fastening generation
- 9022 341 0910 — Spline screw IS-M5x6-10.9Eliminated in new system; retained for older machines · TS 700; retain the specified guard and fastening generation
Service note · TS 700
TS 700: guard conversion starts with wheel removal and belt unloading
Original screws and later captive nuts require distinct removal handling.
- Section 1.9: support with guard is factory-mounted INBOARD, recommended for better balance; outboard mounting is possible according to requirements. REMOVE abrasive wheel before the conversion sequence.
- Water attachment: loosen banjo bolt with combination wrench, remove square nut from its guide inside guard, then remove water hose with connector from adjusting lever. Adjusting lever: remove banjo bolt with seal and square nut from guide, remove other bolt, turn lever UP and remove. Figure numbers reset between these separate steps.
- Original V-belt guard: LOOSEN hexagon-head screws first without removing; turn tensioning nut COUNTERCLOCKWISE about one-quarter turn, maximum to stop = 0; then remove screws. New guard: LOOSEN captive nuts first, make the same tensioning-nut movement, then remove nuts FROM STUDS. Captivity is not an instruction to detach the nuts from the guard.
- Slide V-belt guard FORWARD off the machine, take poly V-belt off front pulley, then remove support with guard. This is the specified historical mechanical sequence, not a hardware operation performed here.
- Historical English TI06/2010, series 4224. Modification introduced continuously; no numeric serial cutoff is supplied. Availability statements describe 2010, not current stock. No physical interchange test was performed.
Source: TI 6/2010, p. 5 · TI 6/2010, p. 6 — guard conversion starts with wheel removal and belt unloading.
No additional parts-table entry added.
Service note · TS 700
TS 700: outboard conversion retains shorter and longer banjo-bolt roles
Guard orientation, stop relocation and free belt movement must be checked.
- Section 1.9: remove limit-stop bolt, limit stop and stop pin. Rotate guard to illustrated OUTBOARD-preparation position in figure 376TI055; install and tighten pin, align limit-stop and support holes, then install/tighten stop screw. Section 1.4/1.5 gives pin 5 Nm and stop attachment 1.5 Nm.
- Move adjusting lever to illustrated position A; install/tighten its screw. Turn assembly so guard is OUTBOARD. Hold square nut in guard guide; fit SHORTER banjo bolt and washer at adjusting lever and tighten with combination wrench. Position A is an illustration locator, not an angle specification.
- Fit support with guard outboard while guiding poly V-belt over pulley; check belt moves easily. Fit V-belt guard, align threaded holes and install original screws WITHOUT tightening. For new captive-nut guard, thread nuts onto studs BY HAND, WITHOUT tightening.
- Water connection: pass LONGER banjo bolt through connector, preserving depicted connector orientation; hold square nut in guard guide; fit connection to adjusting lever and tighten with combination wrench. Then tension ribbed V-belt. The TI does not provide the final tension setting or these other fastener torques; none is invented.
- After assembly, rotate guard fully forwards AND backwards: travel must be LIMITED BY STOP PIN (page 8, figure 376TI059). A freely moving belt alone is not completion. Short/long banjo bolts are not assigned speculative order numbers.
- Historical English TI06/2010, series 4224. Modification introduced continuously; no numeric serial cutoff is supplied. Availability statements describe 2010, not current stock. No physical interchange test was performed.
Source: TI 6/2010, p. 3 · TI 6/2010, p. 6 · TI 6/2010, p. 7 · TI 6/2010, p. 8 — outboard conversion retains shorter and longer banjo-bolt roles.
No additional parts-table entry added.
Service note · TS 700
TS 700: return to inboard mounting uses its own illustrated guard position
The return sequence also ends with a stop-limited travel check.
- Section 1.10: remove abrasive wheel, water attachment and adjusting lever; slacken V-belt, remove V-belt guard and poly V-belt, then remove support with guard.
- Remove limit-stop bolt, limit stop and stop pin. Turn guard to the INBOARD position shown in figure 376TI054, not outboard figure 376TI055. Install/tighten pin; align limit-stop hole with support hole; install/tighten screw. Pin torque 5 Nm and stop attachment1.5 Nm are in sections 1.4/1.5.
- Install adjusting lever, mount support with guard INBOARD, fit ribbed poly V-belt and V-belt guard, connect water connection, then tension belt. Refer to the illustrated source geometry; omitted tension values or other torques are not fabricated.
- Rotate guard forwards AND backwards as far as possible; travel must be LIMITED BY STOP PIN (page 9, figure 376TI061). Pages8/9 label illustrated travel A; page 1 uses A for inboard and B for outboard. These local figure labels are not numerical angles or interchangeable geometry.
- Historical English TI06/2010, series 4224. Modification introduced continuously; no numeric serial cutoff is supplied. Availability statements describe 2010, not current stock. No physical interchange test was performed.
Source: TI 6/2010, p. 3 · TI 6/2010, p. 8 · TI 6/2010, p. 9 — return to inboard mounting uses its own illustrated guard position.
No additional parts-table entry added.
Service note · TS 700
TS 700: both instruction labels from the replacement set must be fitted
The TS 700-only label set also applies to older TS 700 machines.
- Section 2.1 replaces previous instruction labels 0000 967 3521 and 0000 967 3520 with set 0000 960 0101. Previous labels no longer available; the set can also be used on older TS 700 machines.
- ALWAYS attach BOTH instruction labels from the new set. Summary rows 16/17 carry remarks 1/4/5; row 18 carries2/4. The broad summary subheading names TS 700/TS 800, but all three label rows and section 2.1 explicitly say TS 700. Do not assign this set to TS 800.
- The K-sheet repeats the set number at two drawing positions; that does not establish two different sets or authorize fitting only one label. The extracted supersession prose is mixed with the adjacent adjustment-range text, so use the scanned section and summary rows.
- Historical English TI06/2010, series 4224. Modification introduced continuously; no numeric serial cutoff is supplied. Availability statements describe 2010, not current stock. No physical interchange test was performed.
Source: TI 6/2010, p. 9 · TI 6/2010, p. 11 · TI 6/2010, p. 12 — both instruction labels from the replacement set must be fitted.
Part numbers (3)
- 0000 967 3521 — Previous instruction labelDiscontinued; replaced by complete set · TS 700; retain the specified guard and fastening generation
- 0000 967 3520 — Previous instruction labelDiscontinued; replaced by complete set · TS 700; retain the specified guard and fastening generation
- 0000 960 0101 — Set of instruction labelsNew; attach both labels · TS 700; retain the specified guard and fastening generation
Service note · TS 700
TS 700: captive-nut guard and studded support must stay together
Do not combine the old support, belt guard or screws with the new generation.
- Section 3.1: support 4224 791 3903 → 4224 790 5301, and V-belt guard 4224 700 8100 → 4224 700 8113. New guard has captive nuts secured against loss; these mate with STUDS of new support. Three previous screws 4224 708 8400 are no longer required for this generation.
- Old support 3903, guard 8100 and screws 8400 remain available for older machines. They MUST NOT be combined with new support 5301 and guard 8113. Summary row 13/19/21 remarks 3/4 preserve retention AND service restrictions; absence of the old screws from the new assembly is not universal deletion.
- Cross-column extraction falsely pairs TS 700 support 3903 with TS 800 support 3901, and TS 700 new support 5301 with its own guard 8113. These are not replacements of like parts: use the model-specific support/guard pairs above. No universal one-part retrofit is established.
- Historical English TI06/2010, series 4224. Modification introduced continuously; no numeric serial cutoff is supplied. Availability statements describe 2010, not current stock. No physical interchange test was performed.
Source: TI 6/2010, p. 10 · TI 6/2010, p. 11 · TI 6/2010, p. 12 — captive-nut guard and studded support must stay together.
Part numbers (5)
- 4224 791 3903 — Support, screw-fastened generationPrevious; retained · TS 700; retain the specified guard and fastening generation
- 4224 790 5301 — Studded supportNew; matched guard required · TS 700; retain the specified guard and fastening generation
- 4224 700 8100 — V-belt guard, screw-fastenedPrevious; retained · TS 700; retain the specified guard and fastening generation
- 4224 700 8113 — V-belt guard with captive nutsNew; matched support required · TS 700; retain the specified guard and fastening generation
- 4224 708 8400 — Screw, quantity threePrevious generation only · TS 700; retain the specified guard and fastening generation
Wrong number or missing part for the TS 700? Report a correction →