Stihl 4224 · Section L · 11 of 15 · 59 parts
Support with guard with water attachment (43.2007)
Fits TS 700.
Historical fitment & changes (3) — includes parts and conditions not shown on this drawing.
Parts (59)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4224 700 8103 NLA | Guard Ø 350 mm / 14'' → replaced by 4224 700 8102 TI 43/2007 | 1 |
| 2 | 4224 791 3903 | Support Fitment / change note → → replaced by 4224 791 3901 TI 6/2010 | 1 |
| 3 | 9456 621 3600 | Circlip 32x1.2 | 2 |
| 4 | 9503 003 6440 | Grooved ball bearing 6201-2RS → replaced by 9503 003 6420 TI 5/1994 | 2 |
| 5 | 0000 961 1206 | Ring | 1 |
| 6 | 4201 704 0504 | Shaft | 1 |
| 7 | 4201 706 9202 | Washer | 2 |
| 8 | 4221 706 8800 | Rubber ring | 1 |
| 9 | 4221 706 8801 | Rubber ring | 1 |
| 10 | 4224 700 2900 | Adjusting lever | 1 |
| 11 | 9416 868 6510 | Hollow rivet 6.5x0.5x3.0 | 2 |
| 12 | 9022 341 0960 | Spline screw IS-M5x12 → replaced by 9022 341 0980 TI 3/2006 | 2 |
| 13 | 4205 706 2903 | Flange | 1 |
| 14 | 9022 341 1358 | Spline screw IS-M6x28 | 4 |
| 15 | 4224 704 3200 | Sleeve | 4 |
| 16 | 0000 997 1303 | Compression spring | 4 |
| 17 | 0000 958 1212 | Washer | 1 |
| 18 | 4223 036 8600 | Woodruff key | 1 |
| 19 | 4224 764 8501 | Poly V-belt pulley | 1 |
| 20 | 9291 021 0200 | Washer 10.5 | 1 |
| 21 | 9211 260 1350 | Hexagon nut M10x1 l/h thread | 1 |
| 22 | 9450 721 2150 | Circlip 20x1.2 | 1 |
| 23 | 4201 708 8402 | Hexagon head screw M10x18 | 1 |
| 24 | 4201 708 3004 | Thrust washer Ø 103 mm | 1 |
| 25 | 4201 708 3014 | Thrust washer Ø 103 mm | 1 |
| 26 | 4224 700 6800 | Bracket | 1 |
| 27 | 4238 677 8200 | Connector | 1 |
| 28 | 4201 700 4500 | Shut-off cock 1/4" | 1 |
| 29 | 0000 954 1701 | Sealing ring | 1 |
| 30 | 4201 700 7300 | Hose connector | 1 |
| 31 | 9645 945 7506 | O-ring 10x3 | 1 |
| 32 | 4201 670 1700 | Coupling sleeve 1/2" | 1 |
| 33 | not sold separately | Hose 5.6x1.9x614 mm not available as a separate item | 1 |
| 34 | not sold separately | Hose 5.6x1.9x220 mm / 8 11/16'' not available as a separate item | 1 |
| 35 | 9771 021 0921 | Hose clip 10/7 | 4 |
| 36 | 9771 021 0920 | Hose clip 9.5/7 → replaced by 9771 021 0921 TI 43/2007 | 4 |
| 37 | 4224 677 8201 | Connector | 1 |
| 38 | 4224 677 8202 | Connector | 1 |
| 39 | 4201 708 8400 | Banjo bolt | 2 |
| 40 | 9041 216 0950 | Pan head screw M5x10 | 2 |
| 41 | 9211 021 8900 | Hexagon nut G 1/8" | 2 |
| 42 | 4119 791 9400 | Cable clamp | 1 |
| 43 | 0000 706 4600 | Plug | 2 |
| 44 | 4224 708 9100 | Bow | 1 |
| 45 | 9022 341 1280 | Spline screw IS-M6x16 | 1 |
| 46 | 4224 700 8100 | Guard Fitment / change note → | 1 |
| 47 | 4224 708 8400 | Screw Fitment / change note → | 3 |
| 48 | 4205 708 3010 | Thrust washer Ø 118 mm | 1 |
| 49 | 4205 708 3000 | Thrust washer Ø 118 mm | 1 |
| 50 | 4201 670 1701 | Coupling sleeve 3/4" | 1 |
| 51 | 4224 790 9300 | Rubber buffer Fitment / change note → | 1 |
| 52 | 9022 341 0910 | Spline screw IS-M5x6 Fitment / change note → | 1 |
| 53 | 0000 967 3578 | Instruction label | 1 |
| 54 | 0000 967 3903 | Instruction label | 1 |
| 55 | 4224 967 3701 | Instruction label | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4224 690 0102 | Support with guard Ø 350 mm / 14'' no longer available from factory | 1 |
| — | 4224 690 0100 | Support with guard Ø 350 mm / 14'' no longer available from factory | 1 |
| — | 4224 690 0101 | Support with guard Ø 350 mm / 14'' no longer available from factory | 1 |
| — | 0000 937 4049 | Hose 5.6x1.9 mm x 1 m not illustratedoption | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · TS 700
TS 700: support changes occur in two distinct stages
Older-machine use of 3903 does not authorize mixing later captive-nut components.
- Sections 1.1/1.2 are TS 700 ONLY: stop pin in the cast arm and molded guard lugs define the inboard and outboard adjustment ranges. No numerical angle is given. Support 4224 791 3900 is replaced by 4224 791 3903, adding a threaded stop-pin hole and extra limit-stop fastening holes.
- The previous 3900 support is no longer available; 3903 can also be used on older machines with 3900. Summary row 1 carries remarks 1/2. This is the first, defined-adjustment-range stage, not blanket compatibility of every later support.
- Section 3.1 then replaces 3903 by 4224 790 5301 for the captive-nut belt guard. At that second stage 3903 remains available for older machines and old support/guard/screws MUST NOT be combined with new support/guard. The same bulletin thus calls 3903 new in section 1 and previous in section 3; preserve both stages.
- The retained older TS 700 L sheet carries 3903 with guard 4224 700 8103; the TI explicitly discusses 8102/8108. A shared support number does not extend the new-guard service procedure to the unmentioned 8103 guard.
- Historical English TI06/2010, series 4224. Modification introduced continuously; no numeric serial cutoff is supplied. Availability statements describe 2010, not current stock. No physical interchange test was performed.
Source: TI 6/2010, p. 1 · TI 6/2010, p. 2 · TI 6/2010, p. 10 · TI 6/2010, p. 11 · TI 6/2010, p. 12 — support changes occur in two distinct stages.
Part numbers (3)
- 4224 791 3900 — Support without new stop featuresPrevious; discontinued · TS 700; retain the specified guard and fastening generation
- 4224 791 3903 — Support with stop-pin thread and limit-stop holesFirst-stage replacement; retained for older fastening generation · TS 700; retain the specified guard and fastening generation
- 4224 790 5301 — Support with studsSecond-stage replacement; matched captive-nut guard required · TS 700; retain the specified guard and fastening generation
Service note · TS 700
TS 700: old rubber buffer and screw remain for older machines
Elimination with the new stop system is not a universal removal instruction.
- Section 1.6 eliminates rubber buffer 4224 790 9300 and spline screw IS-M5x6-10.9, 9022 341 0910, when the new support-mounted pin and guard lugs determine travel.
- Both old parts remain available for older machines; summary rows 9/10 carry remark 3 and blank new-number cells. Do not delete them from old configurations or infer either part is individually replaced by the new pin.
- Historical English TI06/2010, series 4224. Modification introduced continuously; no numeric serial cutoff is supplied. Availability statements describe 2010, not current stock. No physical interchange test was performed.
Source: TI 6/2010, p. 3 · TI 6/2010, p. 11 · TI 6/2010, p. 12 — old rubber buffer and screw remain for older machines.
Part numbers (2)
- 4224 790 9300 — Rubber bufferEliminated in new system; retained for older machines · TS 700; retain the specified guard and fastening generation
- 9022 341 0910 — Spline screw IS-M5x6-10.9Eliminated in new system; retained for older machines · TS 700; retain the specified guard and fastening generation
Service note · TS 700
TS 700: captive-nut guard and studded support must stay together
Do not combine the old support, belt guard or screws with the new generation.
- Section 3.1: support 4224 791 3903 → 4224 790 5301, and V-belt guard 4224 700 8100 → 4224 700 8113. New guard has captive nuts secured against loss; these mate with STUDS of new support. Three previous screws 4224 708 8400 are no longer required for this generation.
- Old support 3903, guard 8100 and screws 8400 remain available for older machines. They MUST NOT be combined with new support 5301 and guard 8113. Summary row 13/19/21 remarks 3/4 preserve retention AND service restrictions; absence of the old screws from the new assembly is not universal deletion.
- Cross-column extraction falsely pairs TS 700 support 3903 with TS 800 support 3901, and TS 700 new support 5301 with its own guard 8113. These are not replacements of like parts: use the model-specific support/guard pairs above. No universal one-part retrofit is established.
- Historical English TI06/2010, series 4224. Modification introduced continuously; no numeric serial cutoff is supplied. Availability statements describe 2010, not current stock. No physical interchange test was performed.
Source: TI 6/2010, p. 10 · TI 6/2010, p. 11 · TI 6/2010, p. 12 — captive-nut guard and studded support must stay together.
Part numbers (5)
- 4224 791 3903 — Support, screw-fastened generationPrevious; retained · TS 700; retain the specified guard and fastening generation
- 4224 790 5301 — Studded supportNew; matched guard required · TS 700; retain the specified guard and fastening generation
- 4224 700 8100 — V-belt guard, screw-fastenedPrevious; retained · TS 700; retain the specified guard and fastening generation
- 4224 700 8113 — V-belt guard with captive nutsNew; matched support required · TS 700; retain the specified guard and fastening generation
- 4224 708 8400 — Screw, quantity threePrevious generation only · TS 700; retain the specified guard and fastening generation
Wrong number or missing part for the TS 700? Report a correction →