← TS 700 · FW 20 · TS 800

Stihl 4224 · Section K · 10 of 14 · 70 parts

Support with guard with water attachment

Fits TS 800.

Parts diagrams →

Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
10101112131415161718192202122232425262728293303132333435373839393939440404040414243434444454546474849550515253545556575859666061627789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (70)

PosPart numberDescriptionQty
2 4224 700 8107 Guard Ø 416 mm / 16'' 1
3 4224 790 5303 Support 1
4 4224 791 3901 Support Fitment / change note → 1
5 4224 691 0101 Stop pin 1
6 9456 621 3600 Circlip 32x1.2 2
7 9503 003 6440 Grooved ball bearing 6201-2RS → replaced by 9503 003 6420 TI 5/1994 2
8 0000 961 1206 Ring 1
9 4201 704 0504 Shaft 1
10 4201 706 9202 Washer 2
11 4221 706 8800 Rubber ring 1
12 4221 706 8801 Rubber ring 1
13 4224 700 2900 Adjusting lever 1
14 9416 868 6510 Hollow rivet 6.5x0.5x3.0 2
15 9022 341 0960 Spline screw IS-M5x12 → replaced by 9022 341 0980 TI 3/2006 2
16 4205 706 2903 Flange 1
17 9022 341 1358 Spline screw IS-M6x28 4
18 4224 704 3200 Sleeve 4
19 0000 997 1303 Compression spring 4
20 0000 958 1212 Washer 1
21 4223 036 8600 Woodruff key 1
22 4224 764 8502 Poly V-belt pulley 1
23 9291 021 0200 Washer 10.5 1
24 9211 260 1350 Hexagon nut M10x1 l/h thread 1
25 9450 721 2150 Circlip 20x1.2 1
26 4201 708 8402 Hexagon head screw M10x18 1
27 4201 708 3014 Thrust washer Ø 103 mm 1
28 4201 708 3004 Thrust washer Ø 103 mm 1
29 4224 700 6802 Bracket 1
30 4224 700 6800 Bracket 1
31 4238 677 8200 Connector 1
32 4201 700 4500 Shut-off cock 1/4" 1
33 0000 954 1701 Sealing ring 1
34 4201 700 7300 Hose connector 1
35 9645 945 7506 O-ring 10x3 1
37 not sold separately Hose 5.6x1.9x674 mm not available as a separate item 1
38 not sold separately Hose 5.6x1.9x270 mm / 10 5/8'' not available as a separate item 1
39 9771 021 0921 Hose clip 10/7 4
40 9771 021 0920 Hose clip 9.5/7 → replaced by 9771 021 0921 TI 43/2007 4
41 4224 677 8201 Connector 1
42 4224 677 8202 Connector 1
43 4201 708 8400 Banjo bolt 2
44 9041 216 0950 Pan head screw M5x10 2
45 9211 021 8900 Hexagon nut G 1/8" 2
46 4119 791 9400 Cable clamp 1
47 0000 706 4600 Plug 2
48 4224 708 9100 Bow 1
49 9022 341 1280 Spline screw IS-M6x16 1
50 4224 700 8115 Guard Fitment / change note → 1
51 4224 700 8101 Guard Fitment / change note → 1
52 4224 708 8400 Screw Fitment / change note → 3
53 4205 708 3001 NLA Thrust washer Ø 140 mm 1
54 4205 708 3011 NLA Thrust washer Ø 140 mm 1
55 4201 670 1701 Coupling sleeve 3/4" 1
56 4224 790 9300 Rubber buffer 1
57 9022 341 0910 Spline screw IS-M5x6 1
58 0000 967 3699 Instruction label 1
59 0000 967 3902 Instruction label 1
60 9022 341 1220 Spline screw IS-M5x48 1
61 4224 967 3702 NLA Instruction label 1
62 0000 967 7226 Warning pictogram 1
Not numbered on the diagram — assemblies, kits and options
— 4224 690 0119 Support with guard Ø 400 mm / 16'' no longer available from factory 1
— 4224 690 0103 Support with guard Ø 400 mm / 16'' no longer available from factory 1
— 4224 690 0120 Support with guard Ø 400 mm / 16'' Fitment / change note → no longer available from factory 1
— 4224 690 0104 Support with guard Ø 400 mm / 16'' Fitment / change note → → replaced by 4224 791 3903 TI 6/2010 no longer available from factory 1
— 4224 690 0122 Support with guard Ø 400 mm / 16'' no longer available from factory 1
— 4224 690 0110 Support with guard Ø 400 mm / 16'' no longer available from factory 1
— 4224 690 0121 Support with guard Ø 400 mm / 16'' no longer available from factory 1
— 4224 690 0105 Support with guard Ø 400 mm / 16'' no longer available from factory 1
— 4224 690 0117 Support with guard Ø 416 mm / 16'' no longer available from factory 1
— 0000 937 4049 Hose 5.6x1.9 mm x 1 m not illustratedoption 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · TS 800

TS 800: 400 mm assembly preserves TS 800-specific captive-nut restrictions

The historical 5302 support is not silently renamed to catalog 5303.

  • Section 3.2: support 4224 791 3901 is replaced by 4224 790 5302; belt guard 4224 700 8101 by 4224 700 8115. New guard captive nuts mate with new support studs, eliminating the three screws 4224 708 8400 from that generation.
  • Complete support with guard diameter 400 mm 4224 690 0104 is replaced by 4224 690 0120. Summary row 11 includes old support row 14, while row 12 includes new support row 15. These are assembly contents, not a replacement of an entire assembly by a bare support.
  • Old complete assembly 0104, support 3901, guard 8101 and screws 8400 remain available for older machines WITHOUT captive nuts on the V-belt guard. Old support/guard/screws MUST NOT be combined with new support 5302 and guard 8115. Do not generalize the TS 700 support numbers or its defined-adjustment-range procedure to TS 800.
  • Retained TS 800 K-sheet lists support 4224 790 5303 at position 3, whereas original TI section 3.2 and summary row 15 both print4224 790 5302. No evidence here establishes a 5302→5303 supersession or interchange. Preserve the historical5302 number as historical-only with no invented drawing position; catalog5303 stays unchanged.
  • The extracted relation from complete old assembly 0104 to TS 700 support 3903 is a cross-column error, not a supersession. Summary rows 11–15/20/21 and their footnotes were checked against the scans.
  • Historical English TI06/2010, series 4224. Modification introduced continuously; no numeric serial cutoff is supplied. Availability statements describe 2010, not current stock. No physical interchange test was performed.

Source: TI 6/2010, p. 10 · TI 6/2010, p. 11 · TI 6/2010, p. 12 — 400 mm assembly preserves TS 800-specific captive-nut restrictions.

Part numbers (7)
  • 4224 791 3901 — Previous TS 800 supportRetained for machines without captive nuts · TS 800; retain the specified guard and fastening generation
  • 4224 790 5302 — TS 800 studded support as printed in TINew historical version; catalog5303 relation unestablished · TS 800; retain the specified guard and fastening generation
  • 4224 700 8101 — Previous TS 800 V-belt guardRetained for machines without captive nuts · TS 800; retain the specified guard and fastening generation
  • 4224 700 8115 — TS 800 V-belt guard with captive nutsNew; matched studded support required · TS 800; retain the specified guard and fastening generation
  • 4224 708 8400 — Screw, quantity threePrevious generation only · TS 800; retain the specified guard and fastening generation
  • 4224 690 0104 — Previous complete support with400 mm guardRetained; includes old support · TS 800; retain the specified guard and fastening generation
  • 4224 690 0120 — Complete support with400 mm guardNew; includes new support · TS 800; retain the specified guard and fastening generation

Wrong number or missing part for the TS 800? Report a correction →