← HS 72, HS 74, HS 76 · HS 75, HS 80, HS 85

Stihl 4226 · Section J · 9 of 17 · 22 parts

Cutter bar HS 75, 80 1 45 512 843 (42.1999)

Fits HS 75.

Parts diagrams →

Historical fitment & changes (6) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
111011111212131415151616171822334567789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (22)

PosPart numberDescriptionQty
1 4226 641 4602 Guide 420 mm / 17'' Fitment / change note → 2
2 4226 710 6059 Blade 420 mm 1
3 4226 713 6600 Pin Fitment / change note → 2
4 4226 713 1702 Flat spring 420 mm Fitment / change note → 1
5 4226 790 9103 Blade guard 420 mm / 17'' Fitment / change note → 1
6 4226 792 9101 Cutter guard Fitment / change note → 1
7 9022 341 0980 Spline screw IS-M5x16 Fitment / change note →
8 9220 260 0701 Hexagon nut M5 Fitment / change note →
9 4226 648 6700 Slider Fitment / change note →
10 9022 371 1020 Spline screw IS-M5x20 Fitment / change note → → replaced by 9022 371 1050 TI 30/2004 2
11 4226 641 4600 Guide 550 mm / 22'' Fitment / change note → 2
12 4226 710 6052 Blade 550 mm 1
13 4226 713 1700 Flat spring 550 mm Fitment / change note → 1
14 4226 790 9100 Blade guard 550 mm / 22'' Fitment / change note → 1
15 4226 641 4601 NLA Guide 700 mm / 28'' Fitment / change note → 2
16 4226 710 6057 NLA Blade 700 mm 1
17 4226 713 1701 Flat spring 700 mm Fitment / change note → 1
18 4226 790 9104 NLA Blade guard 700 mm / 28'' Fitment / change note → 1
Not numbered on the diagram — assemblies, kits and options
— 4226 710 5931 Cutter bar assy. 420 mm Fitment / change note → no longer available from factory 1
— 4226 710 5901 Cutter bar assy. 550 mm Fitment / change note → no longer available from factory 1
— 4226 710 5902 NLA Cutter bar assy. 550 mm no longer available from factory 1
— 4226 710 5941 NLA Cutter bar assy. 700 mm Fitment / change note → no longer available from factory 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · HS 72 / HS 74 / HS 76 / HS 75 / HS 80 / HS 85

HS 72–85: 420 DS (16 in) longer-slot blade assembly

Check first slot: old 28 mm, new 31 mm; old blades forbidden on new gearbox.

  • Figure 366TI014 KN measures the FIRST SLOT: old 28 mm (1.10 in), new 31 mm (1.22 in). Check this slot before fitting individual blades. ORIGINAL-TYPE BLADES MUST NOT be used with the NEW gearbox. New assemblies should also be used for older machines (remark 2); this is not authorization to mix gearbox parts.
  • Table item 1 assembly includes the listed blade. All other parts remain as before. Every listed original assembly/blade is supplied only while factory stocks last (remark 1).
  • TI length labels are retained exactly; later IPL inch labels and later blade revisions do not silently replace them. Existing catalog rows, notes, positions and later serial restrictions remain unchanged.
  • X 36 209 590 applies ONLY to item 10, the 700 ES assembly. It is not a universal blade or gearbox cutoff.
  • Historical TI04/1997 evidence for HS 72, HS 74, HS 76, HS 75, HS 80 and HS 85, type 4226; the named blade length/carburetor/version remains a restriction, not every variant on every model. Factory-supply remarks describe 1997, not current availability. No hardware operation was performed.

Source: TI 4/1997, p. 1 · TI 4/1997, p. 4 — HS 72–85: 420 DS (16 in) longer-slot blade assembly.

Part numbers (4)
  • 4226 710 5930 — Original cutting blade assembly 420 DS (16 in)original version · TI04/1997 exact named HS models and version restrictions
  • 4226 710 5931 — New cutting blade assembly 420 DS (16 in)new version · TI04/1997 exact named HS models and version restrictions
  • 4226 710 6006 — Original 420 DS (16 in) bladeoriginal version · TI04/1997 exact named HS models and version restrictions
  • 4226 710 6026 — New 420 DS (16 in) bladenew version · TI04/1997 exact named HS models and version restrictions

Service note · HS 72 / HS 74 / HS 76 / HS 75 / HS 80 / HS 85

HS 72–85: 550 DS (21 in) longer-slot blade assembly

Check first slot: old 28 mm, new 31 mm; old blades forbidden on new gearbox.

  • Figure 366TI014 KN measures the FIRST SLOT: old 28 mm (1.10 in), new 31 mm (1.22 in). Check this slot before fitting individual blades. ORIGINAL-TYPE BLADES MUST NOT be used with the NEW gearbox. New assemblies should also be used for older machines (remark 2); this is not authorization to mix gearbox parts.
  • Table item 3 assembly includes the listed blade. All other parts remain as before. Every listed original assembly/blade is supplied only while factory stocks last (remark 1).
  • TI length labels are retained exactly; later IPL inch labels and later blade revisions do not silently replace them. Existing catalog rows, notes, positions and later serial restrictions remain unchanged.
  • X 36 209 590 applies ONLY to item 10, the 700 ES assembly. It is not a universal blade or gearbox cutoff.
  • Historical TI04/1997 evidence for HS 72, HS 74, HS 76, HS 75, HS 80 and HS 85, type 4226; the named blade length/carburetor/version remains a restriction, not every variant on every model. Factory-supply remarks describe 1997, not current availability. No hardware operation was performed.

Source: TI 4/1997, p. 1 · TI 4/1997, p. 4 — HS 72–85: 550 DS (21 in) longer-slot blade assembly.

Part numbers (4)
  • 4226 710 5900 — Original cutting blade assembly 550 DS (21 in)original version · TI04/1997 exact named HS models and version restrictions
  • 4226 710 5901 — New cutting blade assembly 550 DS (21 in)new version · TI04/1997 exact named HS models and version restrictions
  • 4226 710 6000 — Original 550 DS (21 in) bladeoriginal version · TI04/1997 exact named HS models and version restrictions
  • 4226 710 6020 — New 550 DS (21 in) bladenew version · TI04/1997 exact named HS models and version restrictions

Service note · HS 72 / HS 74 / HS 76 / HS 75 / HS 80 / HS 85

HS 72–85: 700 DS (27 in) longer-slot blade assembly

Check first slot: old 28 mm, new 31 mm; old blades forbidden on new gearbox.

  • Figure 366TI014 KN measures the FIRST SLOT: old 28 mm (1.10 in), new 31 mm (1.22 in). Check this slot before fitting individual blades. ORIGINAL-TYPE BLADES MUST NOT be used with the NEW gearbox. New assemblies should also be used for older machines (remark 2); this is not authorization to mix gearbox parts.
  • Table item 5 assembly includes the listed blade. All other parts remain as before. Every listed original assembly/blade is supplied only while factory stocks last (remark 1).
  • TI length labels are retained exactly; later IPL inch labels and later blade revisions do not silently replace them. Existing catalog rows, notes, positions and later serial restrictions remain unchanged.
  • X 36 209 590 applies ONLY to item 10, the 700 ES assembly. It is not a universal blade or gearbox cutoff.
  • Historical TI04/1997 evidence for HS 72, HS 74, HS 76, HS 75, HS 80 and HS 85, type 4226; the named blade length/carburetor/version remains a restriction, not every variant on every model. Factory-supply remarks describe 1997, not current availability. No hardware operation was performed.

Source: TI 4/1997, p. 1 · TI 4/1997, p. 4 — HS 72–85: 700 DS (27 in) longer-slot blade assembly.

Part numbers (4)
  • 4226 710 5940 — Original cutting blade assembly 700 DS (27 in)original version · TI04/1997 exact named HS models and version restrictions
  • 4226 710 5941 — New cutting blade assembly 700 DS (27 in)new version · TI04/1997 exact named HS models and version restrictions
  • 4226 710 6003 — Original 700 DS (27 in) bladeoriginal version · TI04/1997 exact named HS models and version restrictions
  • 4226 710 6023 — New 700 DS (27 in) bladenew version · TI04/1997 exact named HS models and version restrictions

Conditional replacement · HS 75 / HS 80

HS 75 / HS 80: 420 DS to 500 (20 in) DS cutter bar

Historical component changes with a cutter-bar-only cutoff; later catalog serial wording differs.

1 45 521 844 — TI42 page3: HS75/HS80 cutter-bar introduction from this serial; later catalog sheet J marker 1 45 512 843 conflicts, not an inferred complementary endpoint.

  • The 420 DS complete bar becomes 500 (20 in) DS; the table says each complete bar includes items 1–14, and each listed blade includes pin item 3. Separate previous/new rows and blank cells are preserved; a blank does not mean free interchange, zero quantity or a separately orderable new screw.
  • Section 1 introduces a special self-locking spline screw with a POLYAMIDE RING ON ITS SHANK and M5 hexagon nut with locking teeth. Drawing 366TI000 KN shows screw LEFT and nut RIGHT; the arrow identifies the ring. Claimed benefits: nut does not loosen in use, screw retained in blade, slider stays in place when nut removed. No separate new screw order number is printed; do not reuse an old screw number as the new fastener.
  • Page2 drawing 366TI025 KN is explicitly the 750 (30 in) DS bar, even though the table beneath is the 420/500 DS table. Visible callouts 2,5,6,7,11,12 identify blades, distinct guides, flat spring, hexagon nuts and sliders; drawing occurrences are not a complete quantity table for every length.
  • The old M5x16 screw quantity is 3x; old M5x20 screws are 2x, old guide item4 is 2x. Do not apply those old quantities to the new design. The old slider carries remark 2: remains available.
  • Page3 prints modification FROM serial 1 45 521 844 for the cutter bars. This is a model-conditioned component introduction, not a model-identification range and not the bump-guard or starter changeover.
  • Unresolved catalog comparison: the later SCS01-2012 JSON sheet J (doc1767) title contains 1 45 512 843 (42.1999), whereas TI42 page3 prints 1 45 521 844. These are NOT adjacent endpoints. Preserve both; do not silently swap 512/521, manufacture an old-side interval or select a winner. Sheets H/J associate matching complete-bar numbers but their later blade numbers differ; no blade supersession is inferred from the association.
  • TI42/1999 english/USA historical evidence for HS 75 and HS 80 only. Shared 2012 catalog membership does not extend this TI to HS 85, HS 72, HS 74 or HS 76. Factory-availability remarks describe the historical issue, not current stock. No verified physical interchange, universal retrofit, torque or operating procedure is inferred.

Source: TI 42/1999, p. 1 · TI 42/1999, p. 2 · TI 42/1999, p. 3 — 420 DS to 500 (20 in) DS cutter bar.

Part numbers (20)
  • 4226 710 5931 — Cutter bar 420 DSPrevious complete bar; remark 1: no longer factory-available · HS 75 / HS 80; TI42 420 DS to 500 (20 in) DS table only
  • 4226 710 5932 — Cutter bar 500 (20 in) DSNew complete bar; includes items 1–14 as printed · HS 75 / HS 80; TI42 420 DS to 500 (20 in) DS table only
  • 4226 710 6026 — Blade 420 DSItem 1 previous; remark 2: remains available · HS 75 / HS 80; TI42 420 DS to 500 (20 in) DS table only
  • 4226 710 6009 — Blade 500 (20 in) DSItem 2 new; includes pin item 3 · HS 75 / HS 80; TI42 420 DS to 500 (20 in) DS table only
  • 4226 713 6600 — PinItem 3 unchanged; included with both listed blade versions · HS 75 / HS 80; TI42 420 DS to 500 (20 in) DS table only
  • 4226 641 4602 — Guide 420 DSItem 4 previous, 2x; remark 2: remains available · HS 75 / HS 80; TI42 420 DS to 500 (20 in) DS table only
  • 4226 740 6500 — Guide 500 (20 in) DSItem 5 new · HS 75 / HS 80; TI42 420 DS to 500 (20 in) DS table only
  • 4226 704 3500 — Guide 500 (20 in) DSItem 6 new; distinct from item 5 · HS 75 / HS 80; TI42 420 DS to 500 (20 in) DS table only
  • 4226 713 1702 — Flat springItem 7 previous; remark 2: remains available · HS 75 / HS 80; TI42 420 DS to 500 (20 in) DS table only
  • 4230 713 1715 — Flat springItem 7 new · HS 75 / HS 80; TI42 420 DS to 500 (20 in) DS table only
  • 4226 792 9101 — Cutter guardItem 8 previous; remark 2: remains available · HS 75 / HS 80; TI42 420 DS to 500 (20 in) DS table only
  • 4226 792 9700 — Cutter guardItem 8 new · HS 75 / HS 80; TI42 420 DS to 500 (20 in) DS table only
  • 9022 341 0980 — Spline screw IS M5x16Item 9 previous, 3x; new column blank; remark 2: remains available · HS 75 / HS 80; TI42 420 DS to 500 (20 in) DS table only
  • 9220 260 0701 — Locknut M5Item 10 previous; new column blank; remark 2: remains available · HS 75 / HS 80; TI42 420 DS to 500 (20 in) DS table only
  • 9220 263 0702 — Hexagon nutItem 11 new; no quantity printed in this row · HS 75 / HS 80; TI42 420 DS to 500 (20 in) DS table only
  • 4226 648 6700 — SliderItem 12 previous; remark 2: remains available · HS 75 / HS 80; TI42 420 DS to 500 (20 in) DS table only
  • 4226 648 6701 — SliderItem 12 new; paired with previous slider · HS 75 / HS 80; TI42 420 DS to 500 (20 in) DS table only
  • 9022 371 1020 — Spline screw IS M5x20Item 13 previous, 2x; new column blank; remark 2: remains available · HS 75 / HS 80; TI42 420 DS to 500 (20 in) DS table only
  • 4226 790 9103 — Blade guardItem 14 previous; remark 2: remains available · HS 75 / HS 80; TI42 420 DS to 500 (20 in) DS table only
  • 4226 790 9202 — Blade guardItem 14 new · HS 75 / HS 80; TI42 420 DS to 500 (20 in) DS table only

Conditional replacement · HS 75 / HS 80

HS 75 / HS 80: 550 DS to 600 (24 in) DS cutter bar

Historical component changes with a cutter-bar-only cutoff; later catalog serial wording differs.

1 45 521 844 — TI42 page3: HS75/HS80 cutter-bar introduction from this serial; later catalog sheet J marker 1 45 512 843 conflicts, not an inferred complementary endpoint.

  • The 550 DS complete bar becomes 600 (24 in) DS; the table says each complete bar includes items 1–14, and each listed blade includes pin item 3. Separate previous/new rows and blank cells are preserved; a blank does not mean free interchange, zero quantity or a separately orderable new screw.
  • Section 1 introduces a special self-locking spline screw with a POLYAMIDE RING ON ITS SHANK and M5 hexagon nut with locking teeth. Drawing 366TI000 KN shows screw LEFT and nut RIGHT; the arrow identifies the ring. Claimed benefits: nut does not loosen in use, screw retained in blade, slider stays in place when nut removed. No separate new screw order number is printed; do not reuse an old screw number as the new fastener.
  • Page2 drawing 366TI025 KN is explicitly the 750 (30 in) DS bar, even though the table beneath is the 420/500 DS table. Visible callouts 2,5,6,7,11,12 identify blades, distinct guides, flat spring, hexagon nuts and sliders; drawing occurrences are not a complete quantity table for every length.
  • The old M5x16 screw quantity is 4x; old M5x20 screws are 2x, old guide item4 is 2x. Do not apply those old quantities to the new design. The old slider carries remark 2: remains available.
  • Page3 prints modification FROM serial 1 45 521 844 for the cutter bars. This is a model-conditioned component introduction, not a model-identification range and not the bump-guard or starter changeover.
  • Unresolved catalog comparison: the later SCS01-2012 JSON sheet J (doc1767) title contains 1 45 512 843 (42.1999), whereas TI42 page3 prints 1 45 521 844. These are NOT adjacent endpoints. Preserve both; do not silently swap 512/521, manufacture an old-side interval or select a winner. Sheets H/J associate matching complete-bar numbers but their later blade numbers differ; no blade supersession is inferred from the association.
  • TI42/1999 english/USA historical evidence for HS 75 and HS 80 only. Shared 2012 catalog membership does not extend this TI to HS 85, HS 72, HS 74 or HS 76. Factory-availability remarks describe the historical issue, not current stock. No verified physical interchange, universal retrofit, torque or operating procedure is inferred.

Source: TI 42/1999, p. 1 · TI 42/1999, p. 2 · TI 42/1999, p. 3 — 550 DS to 600 (24 in) DS cutter bar.

Part numbers (20)
  • 4226 710 5901 — Cutter bar 550 DSPrevious complete bar; remark 1: no longer factory-available · HS 75 / HS 80; TI42 550 DS to 600 (24 in) DS table only
  • 4226 710 5903 — Cutter bar 600 (24 in) DSNew complete bar; includes items 1–14 as printed · HS 75 / HS 80; TI42 550 DS to 600 (24 in) DS table only
  • 4226 710 6020 — Blade 550 DSItem 1 previous; remark 2: remains available · HS 75 / HS 80; TI42 550 DS to 600 (24 in) DS table only
  • 4226 710 6019 — Blade 600 (24 in) DSItem 2 new; includes pin item 3 · HS 75 / HS 80; TI42 550 DS to 600 (24 in) DS table only
  • 4226 713 6600 — PinItem 3 unchanged; included with both listed blade versions · HS 75 / HS 80; TI42 550 DS to 600 (24 in) DS table only
  • 4226 641 4600 — Guide 550 DSItem 4 previous, 2x; remark 2: remains available · HS 75 / HS 80; TI42 550 DS to 600 (24 in) DS table only
  • 4226 740 6501 — Guide 600 (24 in) DSItem 5 new · HS 75 / HS 80; TI42 550 DS to 600 (24 in) DS table only
  • 4226 704 3501 — Guide 600 (24 in) DSItem 6 new; distinct from item 5 · HS 75 / HS 80; TI42 550 DS to 600 (24 in) DS table only
  • 4226 713 1700 — Flat springItem 7 previous; remark 2: remains available · HS 75 / HS 80; TI42 550 DS to 600 (24 in) DS table only
  • 4230 713 1715 — Flat springItem 7 new · HS 75 / HS 80; TI42 550 DS to 600 (24 in) DS table only
  • 4226 792 9101 — Cutter guardItem 8 previous; remark 2: remains available · HS 75 / HS 80; TI42 550 DS to 600 (24 in) DS table only
  • 4226 792 9700 — Cutter guardItem 8 new · HS 75 / HS 80; TI42 550 DS to 600 (24 in) DS table only
  • 9022 341 0980 — Spline screw IS M5x16Item 9 previous, 4x; new column blank; remark 2: remains available · HS 75 / HS 80; TI42 550 DS to 600 (24 in) DS table only
  • 9220 260 0701 — Locknut M5Item 10 previous; new column blank; remark 2: remains available · HS 75 / HS 80; TI42 550 DS to 600 (24 in) DS table only
  • 9220 263 0702 — Hexagon nutItem 11 new; no quantity printed in this row · HS 75 / HS 80; TI42 550 DS to 600 (24 in) DS table only
  • 4226 648 6700 — SliderItem 12 previous; remark 2: remains available · HS 75 / HS 80; TI42 550 DS to 600 (24 in) DS table only
  • 4226 648 6701 — SliderItem 12 new; paired with previous slider · HS 75 / HS 80; TI42 550 DS to 600 (24 in) DS table only
  • 9022 371 1020 — Spline screw IS M5x20Item 13 previous, 2x; new column blank; remark 2: remains available · HS 75 / HS 80; TI42 550 DS to 600 (24 in) DS table only
  • 4226 790 9100 — Blade guardItem 14 previous; remark 2: remains available · HS 75 / HS 80; TI42 550 DS to 600 (24 in) DS table only
  • 4226 790 9200 — Blade guardItem 14 new · HS 75 / HS 80; TI42 550 DS to 600 (24 in) DS table only

Conditional replacement · HS 75 / HS 80

HS 75 / HS 80: 700 DS to 750 (30 in) DS cutter bar

Historical component changes with a cutter-bar-only cutoff; later catalog serial wording differs.

1 45 521 844 — TI42 page3: HS75/HS80 cutter-bar introduction from this serial; later catalog sheet J marker 1 45 512 843 conflicts, not an inferred complementary endpoint.

  • The 700 DS complete bar becomes 750 (30 in) DS; the table says each complete bar includes items 1–14, and each listed blade includes pin item 3. Separate previous/new rows and blank cells are preserved; a blank does not mean free interchange, zero quantity or a separately orderable new screw.
  • Section 1 introduces a special self-locking spline screw with a POLYAMIDE RING ON ITS SHANK and M5 hexagon nut with locking teeth. Drawing 366TI000 KN shows screw LEFT and nut RIGHT; the arrow identifies the ring. Claimed benefits: nut does not loosen in use, screw retained in blade, slider stays in place when nut removed. No separate new screw order number is printed; do not reuse an old screw number as the new fastener.
  • Page2 drawing 366TI025 KN is explicitly the 750 (30 in) DS bar, even though the table beneath is the 420/500 DS table. Visible callouts 2,5,6,7,11,12 identify blades, distinct guides, flat spring, hexagon nuts and sliders; drawing occurrences are not a complete quantity table for every length.
  • The old M5x16 screw quantity is 5x; old M5x20 screws are 2x, old guide item4 is 2x. Do not apply those old quantities to the new design. The 700/750 DS slider row12 has NO remark 2; do not copy the old-slider availability remark from the two shorter tables.
  • Page3 prints modification FROM serial 1 45 521 844 for the cutter bars. This is a model-conditioned component introduction, not a model-identification range and not the bump-guard or starter changeover.
  • Unresolved catalog comparison: the later SCS01-2012 JSON sheet J (doc1767) title contains 1 45 512 843 (42.1999), whereas TI42 page3 prints 1 45 521 844. These are NOT adjacent endpoints. Preserve both; do not silently swap 512/521, manufacture an old-side interval or select a winner. Sheets H/J associate matching complete-bar numbers but their later blade numbers differ; no blade supersession is inferred from the association.
  • TI42/1999 english/USA historical evidence for HS 75 and HS 80 only. Shared 2012 catalog membership does not extend this TI to HS 85, HS 72, HS 74 or HS 76. Factory-availability remarks describe the historical issue, not current stock. No verified physical interchange, universal retrofit, torque or operating procedure is inferred.

Source: TI 42/1999, p. 1 · TI 42/1999, p. 2 · TI 42/1999, p. 3 — 700 DS to 750 (30 in) DS cutter bar.

Part numbers (20)
  • 4226 710 5941 — Cutter bar 700 DSPrevious complete bar; remark 1: no longer factory-available · HS 75 / HS 80; TI42 700 DS to 750 (30 in) DS table only
  • 4226 710 5942 — Cutter bar 750 (30 in) DSNew complete bar; includes items 1–14 as printed · HS 75 / HS 80; TI42 700 DS to 750 (30 in) DS table only
  • 4226 710 6023 — Blade 700 DSItem 1 previous; remark 2: remains available · HS 75 / HS 80; TI42 700 DS to 750 (30 in) DS table only
  • 4226 710 6031 — Blade 750 (30 in) DSItem 2 new; includes pin item 3 · HS 75 / HS 80; TI42 700 DS to 750 (30 in) DS table only
  • 4226 713 6600 — PinItem 3 unchanged; included with both listed blade versions · HS 75 / HS 80; TI42 700 DS to 750 (30 in) DS table only
  • 4226 641 4601 — Guide 700 DSItem 4 previous, 2x; remark 2: remains available · HS 75 / HS 80; TI42 700 DS to 750 (30 in) DS table only
  • 4226 740 6502 — Guide 750 (30 in) DSItem 5 new · HS 75 / HS 80; TI42 700 DS to 750 (30 in) DS table only
  • 4226 704 3502 — Guide 750 (30 in) DSItem 6 new; distinct from item 5 · HS 75 / HS 80; TI42 700 DS to 750 (30 in) DS table only
  • 4226 713 1701 — Flat springItem 7 previous; remark 2: remains available · HS 75 / HS 80; TI42 700 DS to 750 (30 in) DS table only
  • 4230 713 1715 — Flat springItem 7 new · HS 75 / HS 80; TI42 700 DS to 750 (30 in) DS table only
  • 4226 792 9101 — Cutter guardItem 8 previous; remark 2: remains available · HS 75 / HS 80; TI42 700 DS to 750 (30 in) DS table only
  • 4226 792 9700 — Cutter guardItem 8 new · HS 75 / HS 80; TI42 700 DS to 750 (30 in) DS table only
  • 9022 341 0980 — Spline screw IS M5x16Item 9 previous, 5x; new column blank; remark 2: remains available · HS 75 / HS 80; TI42 700 DS to 750 (30 in) DS table only
  • 9220 260 0701 — Locknut M5Item 10 previous; new column blank; remark 2: remains available · HS 75 / HS 80; TI42 700 DS to 750 (30 in) DS table only
  • 9220 263 0702 — Hexagon nutItem 11 new; no quantity printed in this row · HS 75 / HS 80; TI42 700 DS to 750 (30 in) DS table only
  • 4226 648 6700 — SliderItem 12 previous; remark blank in 750 DS table · HS 75 / HS 80; TI42 700 DS to 750 (30 in) DS table only
  • 4226 648 6701 — SliderItem 12 new; remark blank in 750 DS table · HS 75 / HS 80; TI42 700 DS to 750 (30 in) DS table only
  • 9022 371 1020 — Spline screw IS M5x20Item 13 previous, 2x; new column blank; remark 2: remains available · HS 75 / HS 80; TI42 700 DS to 750 (30 in) DS table only
  • 4226 790 9104 — Blade guardItem 14 previous; remark 2: remains available · HS 75 / HS 80; TI42 700 DS to 750 (30 in) DS table only
  • 4226 790 9203 — Blade guardItem 14 new · HS 75 / HS 80; TI42 700 DS to 750 (30 in) DS table only

Wrong number or missing part for the HS 75? Report a correction →