Stihl 4226 · Section K · 10 of 17 · 30 parts
Cutter bar HS 85
Fits HS 85.
Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.
Parts (30)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4226 740 6505 | Guide 600 mm / 24" | 1 |
| 2 | 4226 704 3505 | Guide 600 mm / 24" | 1 |
| 3 | not sold separately | Blade 600 mm / 24" not available as a separate item | 1 |
| 4 | not sold separately | Blade 600 mm / 24" not available as a separate item | 1 |
| 5 | 4226 713 6600 | Pin | 1 |
| 6 | 4230 713 1715 | Flat spring | 1 |
| 7 | 4226 790 9205 | Blade guard 600 mm / 24" | 1 |
| 8 | 4226 740 6503 | Guide 750 mm / 30" | 1 |
| 9 | 4226 704 3503 | Guide 750 mm / 30" | 1 |
| 10 | not sold separately | Blade 750 mm / 30" not available as a separate item | 1 |
| 11 | not sold separately | Blade 750 mm / 30" not available as a separate item | 1 |
| 12 | 4226 790 9201 | Blade guard 750 mm / 30" | 1 |
| 13 | 4226 740 6504 | Guide 1000 mm / 40" | 1 |
| 14 | 4226 704 3504 | Guide 1000 mm / 40" | 1 |
| 15 | not sold separately | Blade 1000 mm / 40" not available as a separate item | 1 |
| 16 | not sold separately | Blade 1000 mm / 40" not available as a separate item | 1 |
| 17 | 4226 790 9204 | Blade guard 1000 mm / 40" | 1 |
| 18 | 4226 648 6701 | Slider | |
| 19 | 9220 263 0702 | Hexagon nut M5 | |
| 20 | 9022 371 1020 | Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 | 2 |
| 21 | 4226 717 3302 | Catcher blade 600 mm | 1 |
| 22 | 4226 717 3301 | Catcher blade 750 mm, 1000 mm | 1 |
| 23 | 4226 790 9800 NLA | Guide guard option | 1 |
| 24 | 4226 792 9001 NLA | Guide guard option | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4226 710 5905 | Cutter bar 600 mm / 24" | 1 |
| — | 4226 710 6055 NLA | Blade 600 mm / 24" | 1 |
| — | 4226 710 5923 | Cutter bar 750 mm / 30" | 1 |
| — | 4226 710 6053 NLA | Blade 750 mm / 30" | 1 |
| — | 4226 710 6054 NLA | Blade 1000 mm / 40" | 1 |
| — | 4226 007 1003 NLA | Guide guard kit option | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · HS 85
HS 85: blade-guide and handle torques
Three HS85-only values; model-specific fasteners and mounting locations retained.
- HS85 ONLY, Nm: IS-M5x25 blade guide/gear housing 9.5; IS-M5x16 rubber buffer/gear housing 5.5; IS-M5x30 handle halves 2.5. Do not transfer HS75/80 buffer or handle values.
- Current early cutter sheet shows IS-M5x20 while this TI specifies IS-M5x25 for the blade guide; preserve the configuration/fastener difference. Later cutter-sheet serial boundaries are not supplied by this TI and are not inferred here.
- Historical HS 75, HS 80 and HS 85 type 4226 evidence, restricted to the models named in this note. Replacement of HS 72/74/76 is not parts interchangeability. No serial cutoff or calendar introduction date is supplied. No hardware operation was performed.
Source: TI 17/1996, p. 1 · TI 17/1996, p. 7 — HS85 blade-guide and handle torques.
No additional parts-table entry added.
Wrong number or missing part for the HS 85? Report a correction →