Stihl 4228 · Section F · 6 of 10 · 36 parts
Carburetor C1Q-S67
Fits HS 45.
Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.
Parts (36)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4137 120 7100 | Throttle shaft with lever | 1 |
| 2 | 1123 122 3000 | Spring | 1 |
| 3 | 4228 121 3302 | Throttle shutter | 1 |
| 4 | 1120 122 7400 | Round head screw | 1 |
| 5 | 1125 122 9001 | E-clip | 1 |
| 6 | 4128 121 8901 | Pin | 1 |
| 7 | 1120 122 9000 | E-clip | 1 |
| 8 | 1129 121 4800 | Pump diaphragm | 1 |
| 9 | 1123 129 0905 | Gasket | 1 |
| 10 | 1123 121 0800 | End cover | 1 |
| 11 | 1125 122 4200 | Clamp | 1 |
| 12 | 4229 122 6200 | Idle speed adjustment screw | 1 |
| 13 | 1120 122 7800 | Oval head screw | 1 |
| 14 | 4116 121 5100 | Inlet needle | 1 |
| 15 | 1120 122 3004 | Spring | 1 |
| 16 | 1125 121 5000 | Inlet control lever | 1 |
| 17 | 1120 121 9200 | Spindle | 1 |
| 18 | 1120 122 6600 | Collar screw | 1 |
| 19 | 1129 129 0900 | Gasket → replaced by 4134 121 4700 TI 16/2009 | 1 |
| 20 | 4129 121 4700 | Metering diaphragm | 1 |
| 21 | 4140 120 2200 | Flange | 1 |
| 22 | 4226 122 7100 | Screw | 4 |
| 23 | 4228 122 6801 | Low speed adjustment screw | 1 |
| 24 | 4229 122 6700 | High speed adjustment screw | 1 |
| 25 | 4229 121 2700 | Cap | 1 |
| 26 | 1123 121 7800 | Strainer | 1 |
| 27 | 4228 121 5602 | Fixed jet 0.39 | 1 |
| 28 | 4140 121 0800 | End cover | 1 |
| 29 | 4226 121 2700 | Cap | 1 |
| 30 | 4137 121 8600 | Washer | 1 |
| 31 | 4229 121 5800 | Pump piston | 1 |
| 32 | 4140 122 3600 | Sealing ring → replaced by 4314 122 3600 TI 20/2008 | 1 |
| 33 | 4229 122 3001 | Spring | 1 |
| 34 | 1120 121 7801 | Strainer | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4228 120 0603 | Carburetor C1Q-S67 Fitment / change note → no longer available from factory | 1 |
| — | 1129 007 1062 | Set of carburetor parts → replaced by 4128 007 1060, 4128 007 1060 TI 6/2009 | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Conditional replacement · HS 45
HS 45 C1Q-S67: limiter and service settings
The three-screw carburetor has a 270-degree H limiter; the bulletin distinguishes uncapped service setting from user adjustment.
- C1Q-S67 4228 120 0603 replaces LD/BIS C1Q-S54 4228 120 0601 as part of the model update package. Introduction is in progress, with no serial cutoff. Previous C1Q-S54 remains a spare for older machines; new-carburetor component parts are referred to the IPL.
- The H screw has a limiter cap over its knurled head; the body stop pin restricts rotation to 270 degrees (3/4 turn). L and LA have funnel-shaped access caps, not a claimed L mixture limiter.
- For H-screw replacement or carburetor cleaning the TI removes the H cap with suitable pliers. Never re-use a removed cap because it may be damaged. Check the air filter and spark-arresting screen and clean or replace as necessary.
- The uncapped standard H service setting is 1 1/2 turns open from lightly seated. Align a new H cap at the rich stop and press it home against the carburetor body. Do not import the two-detent seating instructions of another carburetor.
- For idle adjustment, L starts one full turn counterclockwise from lightly seated; LA sets 2,800 RPM, checked with a tachometer. Check repeated acceleration and smooth idle. These are source-specific historical instructions, not a universal tuning recipe.
- Users have 270-degree H adjustment for conditions such as altitude; the TI refers the user procedure to the owner manual, Adjusting the Carburetor. The exact HS 45 owner-manual edition was not located in the bounded retained inventory: a documented source gap, not global absence. The cover illustration shows H 3/4 and L 1; this does not override the explicitly uncapped H service setting of 1 1/2 turns.
- Edition boundary: the later HS 45 workshop manual RA_253_00_01_01 (2005-03), printed pages 33–35 (PDF 34–36), distinguishes a short cap seated at the second noticeable detent, not against the body, from a long cap seated against the body. It is not the missing 2001 owner manual. Do not identify the TI cap as either later type by assumption; its own body-seating instruction remains source-attributed. Dependency evidence: docs/ti26-2001-dependencies.json.
- HS 45 only. Factory availability describes the 2001 bulletin, not present stock. No physical interchange or running adjustment was tested.
Source: TI 26/2001, p. 3 · TI 26/2001, p. 4 · TI 26/2001, p. 5 · TI 26/2001, p. 7 — Sections 4, 4.1.1–4.1.9 and 4.5 carburetor rows.
Part numbers (2)
- 4228 120 0601 — Carburetor C1Q-S54Previous LD generation · HS 45; configuration restrictions in this note
- 4228 120 0603 — Carburetor C1Q-S67H/L/LA generation · HS 45; configuration restrictions in this note
Conditional replacement · HS 45
HS 45 ignition and crankshaft: new-carburetor restriction
Machines with C1Q-S67 require the new ignition module and re-keyed crankshaft when repaired.
- Ignition module 4140 400 1302 replaces 4140 400 1300 together with crankshaft 4228 030 0402 replacing 4228 030 0400. The crankshaft flywheel key slot changes position; the drawing compares the old and new slots but specifies no numerical timing angle.
- For repairs to HS 45 machines with carburetor 4228 120 0603, only the new versions of these parts may be used. The package optimizes timing and cutoff speed range, but gives no cutoff RPM or permission to mix generations.
- Previous module and crankshaft remain available for older machines. Introduction is in progress with no serial stated. The later retained IPL module 4140 400 1308 does not silently supersede the TI-specific 1302 assertion; this note does not establish that later relationship.
- HS 45 only. Factory availability describes the 2001 bulletin, not present stock. No physical interchange or running adjustment was tested.
Source: TI 26/2001, p. 6 · TI 26/2001, p. 7 — Section 4.4, key-slot drawing and 4.5 rows 15–16.
Part numbers (5)
- 4140 400 1300 — Ignition modulePrevious · HS 45; configuration restrictions in this note
- 4140 400 1302 — Ignition moduleRequired new version for C1Q-S67 · HS 45; configuration restrictions in this note
- 4228 030 0400 — CrankshaftPrevious key-slot position · HS 45; configuration restrictions in this note
- 4228 030 0402 — CrankshaftNew key-slot position · HS 45; configuration restrictions in this note
- 4228 120 0603 — Carburetor C1Q-S67Restriction identifier · HS 45; configuration restrictions in this note
Wrong number or missing part for the HS 45? Report a correction →