Stihl 4229 · Section O · 13 of 17 · 36 parts
Fan housing inside SH 85
Fits SH 85.
Historical fitment & changes (9) — includes parts and conditions not shown on this drawing.
Parts (36)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4229 700 4126 | Fan housing, inside | 1 |
| 2 | 9443 825 7130 | Hollow rivet 7.5x1x6.8 | 3 |
| 3 | 0000 350 5800 | Tank vent → replaced by 0000 350 5804 TI 41/2003 | 1 |
| 4 | not sold separately | O-ring not available as a separate item | 1 |
| 5 | 4229 358 7702 | Hose | 1 |
| 6 | 4229 084 8300 | Reflector foil | 1 |
| 7 | 4229 716 6800 | Collar screw | 1 |
| 8 | 0000 350 3502 | Pickup body | 1 |
| 9 | 4229 967 3701 | Warning pictogram BG / SH | 1 |
| 10 | 0000 967 3693 | Warning pictogram Filler cap | 1 |
| 11 | 0000 967 3500 NLA | Instruction label | 1 |
| 12 | 4229 967 3505 | Instruction label | 1 |
| 14 | 9075 478 4159 | Pan head self-tapping screw IS-D5x24 | 3 |
| 15 | 0000 350 0517 | Filler cap | 1 |
| 16 | 0000 350 0900 | Rope | 1 |
| 17 | 9645 951 3890 | O-ring 35x3-FPM 80 | 1 |
| 18 | 4229 790 0609 | Handle molding | 1 |
| 19 | not sold separately | Locking lever not available as a separate item | 1 |
| 20 | not sold separately | Washer not available as a separate item | 2 |
| 21 | not sold separately | Cup spring 16 not available as a separate item | 2 |
| 22 | not sold separately | Locking washer 4 not available as a separate item | 1 |
| 23 | not sold separately | Cam not available as a separate item | 1 |
| 25 | 4229 430 0202 | Stop switch | 1 |
| 26 | 4229 435 1700 | Protective cap | 1 |
| 27 | 4229 440 1900 | Lead | 1 |
| 28 | 4229 440 1903 | Lead | 1 |
| 29 | 4229 182 1004 | Throttle trigger | 1 |
| 30 | 4229 182 1500 | Throttle rod | 1 |
| 31 | 4229 791 0801 | Handle molding, right | 1 |
| 32 | 4229 791 0802 | Handle molding, left | 1 |
| 33 | 4229 791 0200 | Handle | 1 |
| 34 | 4229 706 8500 | Foot | 4 |
| 35 | 9074 478 4425 | Pan head self-tapping screw IS-P6x19 | 2 |
| 36 | 4229 440 2200 | Ground wire option | 1 |
| 40 | 4203 350 5801 NLA | Tank vent → replaced by 0000 350 5800 TI 18/2002 | 1 |
| 41 | 4223 353 9201 | Grommet | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: later handle and housing access
The 2005 component manual separates handle-molding layouts, limits removable handle feet to BG 85/SH 85, and excludes a BG 65 setting lever.
- Later component evidence: January 2005, not a contemporaneous 1999 instruction or proof of original equipment. The introduction covers BG 45/46/55/65/85 and SH 55/85; this TI29-linked note is limited to BG 55/65/85 and SH 55/85 and the explicitly stated component variants. Catalog assembly links are navigation, not proof that all revisions fit. The manual separately distinguishes stop-switch versions up to/from 2001; the overlapping year labels do not establish an exact production or serial cutoff.
- Sections 5–5.2, printed page 11 / PDF12, begin by removing the fan housing with rewind starter (section 7.2) and the spark plug. Remove the indicated screws and lift off the handle molding. The illustrations distinguish BG 45/55 and SH 55 from BG 65/85 and SH 85; BG 45 is outside this TI29 intersection, and the page does not supply a BG 46 layout.
- BG 65 has no setting lever. Setting-lever replacement, when applicable, is delegated to section 8.2; it must not be inferred for BG 55 or SH 55 from the shared illustration. If necessary, pull the grip molding out of its guides and lift it away, then reinstall in reverse sequence.
- Section 5.2 is explicitly BG 85 and SH 85 only: remove the two indicated screws and handle, pull the feet upwards out of the handle, then reassemble in reverse sequence. No handle-foot replacement number or transfer to BG 55/65 or SH 55 is established.
- The section 3.2 table gives IS-P6x19 handle/inner-blower-housing screws 5.0 Nm for BG 85/SH 85 only and IS-P6x19 handle-molding/inner-blower-housing screws 4.0 Nm for BG 65/85 and SH 85 only. The table does not supply that latter torque for BG 55 or SH 55; do not extend it merely because the same removal page includes them.
- For existing DG/P threads, section 3.2 says turn the screw counterclockwise until it drops slightly into the existing thread, then tighten clockwise with a torque wrench to the specified torque. Maximum power-screwdriver speeds in polymer are 600 rpm for Plastoform and 500 rpm for DG screws. Do not mix screws with and without binding heads. These general screw instructions do not resolve any variant-specific missing torque.
- The component manual requires the instruction manual safety precautions and applicable local regulations for any engine run. Fuel work is outdoors only, away from fire, flame, sparks or heat; wipe up spilled fuel immediately. These are source-reviewed reference notes, not a complete repair instruction or hardware verification. Exact owner-manual and remaining component dependencies stay open.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 component dependency; later2005 BG/SH 55, 65, 85: later handle and housing access.
Later manual evidence: STIHL Series 4140 Components BG, SH service manual (2005-01), section BG/SH 55, 65, 85: later handle and housing access, PDF pages 1, 2, 3, 4, 6, 7, 12, 15
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: later throttle trigger, cable and rod
The 2005 component handbook keeps cable and rod removal paths separate; neither path establishes a retrofit or a model-year changeover.
- Later component evidence: January 2005, not a contemporaneous 1999 instruction or proof of original equipment. The introduction covers BG 45/46/55/65/85 and SH 55/85; this TI29-linked note is limited to BG 55/65/85 and SH 55/85 and the explicitly stated component variants. Catalog assembly links are navigation, not proof that all revisions fit. The manual separately distinguishes stop-switch versions up to/from 2001; the overlapping year labels do not establish an exact production or serial cutoff.
- Sections 8.1, 8.5 and 8.6, printed pages 18 and 21 / PDF19 and22, first remove the handle molding via 5.1. For the throttle trigger, disconnect it from the cable on cable-equipped machines or from the rod on rod-equipped machines, then reinstall in reverse sequence. Diagram callouts identify components, not replacement part numbers.
- For cable removal, disconnect it from the throttle trigger, take it out of the guides in the inner fan housing, remove the carburetor via section 9.2.2, then push the cable out of the tensioner and remove it. Reinstall in reverse sequence. Carburetor removal is reviewed separately in the later carburetor/spacer-flange note; the control section supplies no cable adjustment clearance, free play or tension specification.
- For rod removal, remove the throttle trigger and disconnect the rod, then disconnect the rod from the carburetor; reinstall in reverse sequence. Unlike cable removal, this section does not direct removal of the carburetor. Preserve that distinction rather than imposing one removal path on both versions.
- The illustrations locate cable guides, tensioner and rod endpoints. They do not establish cable length, rod dimensions, replacement numbers, cable-to-rod interchange or a year/serial assignment. The separate stop-switch year headings must not be used to date the throttle-linkage variant.
- The component manual requires the instruction manual safety precautions and applicable local regulations for any engine run. Fuel work is outdoors only, away from fire, flame, sparks or heat; wipe up spilled fuel immediately. These are source-reviewed reference notes, not a complete repair instruction or hardware verification. Exact owner-manual and remaining component dependencies stay open.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 component dependency; later2005 BG/SH 55, 65, 85: later throttle trigger, cable and rod.
Later manual evidence: STIHL Series 4140 Components BG, SH service manual (2005-01), section BG/SH 55, 65, 85: later throttle trigger, cable and rod, PDF pages 1, 3, 4, 12, 19, 22
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · BG 85 / SH 85
BG 85 / SH 85: later setting-lever assembly
Only BG 85 and SH 85 receive the setting-lever procedure; cup-spring orientation and cam alignment remain required.
- Later component evidence: January 2005, not a contemporaneous 1999 instruction or proof of original equipment. The introduction covers BG 45/46/55/65/85 and SH 55/85; this TI29-linked setting-lever note is limited to BG 85 and SH 85 only. Catalog assembly links are navigation, not proof that all revisions fit. The manual separately distinguishes stop-switch versions up to/from 2001; the overlapping year labels do not establish an exact production or serial cutoff.
- Section 8.2, printed page 19 / PDF20, is explicitly BG 85 and SH 85 only. This record does not apply the setting lever to BG 55, BG 65 or SH 55. Section 5.1 separately says BG 65 has no setting lever; the shared handle layout is not evidence of one.
- After removing the handle molding, ease the E-clip off the setting-lever stub, remove the cam, then withdraw the lever with its two washers and two cup springs from the molding. Figure 932RA226 labels lever1, washers2/5, cup springs3/4, molding6, cam7 and E-clip8; these are drawing positions, not part numbers.
- Reassemble in reverse sequence, placing the washers and cup springs on the stub and pushing it into the handle molding. The two cup springs must retain the installed orientation shown in figure 932RA226; the exploded inset is part of the instruction, not an optional illustration. No unverified flat-washer substitution, spring dimension or clamping torque is supplied.
- Fit the cam so it lines up with the marking on the handle housing, as shown in figure 932RA227, then seat the E-clip in the stub groove and finish reverse assembly. The marking is a component-alignment reference, not a graduated throttle speed setting. No current replacement number or cross-model lever interchange is established.
- The component manual requires the instruction manual safety precautions and applicable local regulations for any engine run. Fuel work is outdoors only, away from fire, flame, sparks or heat; wipe up spilled fuel immediately. These are source-reviewed reference notes, not a complete repair instruction or hardware verification. Exact owner-manual and remaining component dependencies stay open.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 component dependency; later2005 BG 85 / SH 85: later setting-lever assembly.
Later manual evidence: STIHL Series 4140 Components BG, SH service manual (2005-01), section BG 85 / SH 85: later setting-lever assembly, PDF pages 1, 3, 4, 12, 20
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: later stop-switch version distinction
The handbook separates a switch up to 2001 from a switch with protective cap from 2001, without resolving the shared boundary year.
- Later component evidence: January 2005, not a contemporaneous 1999 instruction or proof of original equipment. The introduction covers BG 45/46/55/65/85 and SH 55/85; this TI29-linked note is limited to BG 55/65/85 and SH 55/85 and the explicitly stated component variants. Catalog assembly links are navigation, not proof that all revisions fit. The manual separately distinguishes stop-switch versions up to/from 2001; the overlapping year labels do not establish an exact production or serial cutoff.
- Section 8.3.1, printed page 19 / PDF20, is headed Version up to 2001. Use a flat screwdriver to ease the switch out of the handle molding, then detach the short-circuit and ground-wire connectors. Reinstall in reverse sequence and check correct wire positions. This subsection does not list prior removal of the handle molding.
- Section 8.3.2, printed page 20 / PDF21, is headed Version from 2001. It first removes the handle molding via 5.1, then uses a flat screwdriver to ease out both the stop switch and protective cap, and disconnects the short-circuit and ground-wire connectors. Reinstall in reverse sequence and check correct wire positions. Do not silently omit the protective cap or transfer the older access sequence.
- The source literally uses both up to 2001 and from 2001. It gives no month, serial threshold or exclusive boundary, so the overlap at 2001 remains unresolved; these labels are not an executable year-based selector. They do not prove that the later cap was original equipment on a 1999 machine.
- No switch part number, terminal pinout, electrical test threshold or conversion kit is given in these subsections. Catalog TI references such as 04/2001 or 45/2001 are bulletin identifiers, not an inferred switch installation date or serial cutoff.
- The component manual requires the instruction manual safety precautions and applicable local regulations for any engine run. Fuel work is outdoors only, away from fire, flame, sparks or heat; wipe up spilled fuel immediately. These are source-reviewed reference notes, not a complete repair instruction or hardware verification. Exact owner-manual and remaining component dependencies stay open.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 component dependency; later2005 BG/SH 55, 65, 85: later stop-switch version distinction.
Later manual evidence: STIHL Series 4140 Components BG, SH service manual (2005-01), section BG/SH 55, 65, 85: later stop-switch version distinction, PDF pages 1, 3, 4, 12, 20, 21
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: later short-circuit and ground-wire routing
From-2001 wire routing differs between BG55/SH55 and BG65/BG85/SH85; all retained wires must seat in the housing guides.
- Later component evidence: January 2005, not a contemporaneous 1999 instruction or proof of original equipment. The introduction covers BG 45/46/55/65/85 and SH 55/85; this TI29-linked note is limited to BG 55/65/85 and SH 55/85 and the explicitly stated component variants. Catalog assembly links are navigation, not proof that all revisions fit. The manual separately distinguishes stop-switch versions up to/from 2001; the overlapping year labels do not establish an exact production or serial cutoff.
- Section 8.4, printed page 20 / PDF21, removes the handle molding and the appropriate stop-switch version, then disconnects the short-circuit and ground-wire connectors from the ignition module. Figure 932RA101 identifies the two connectors but does not establish a substitute wire specification or permission to omit either circuit.
- The first restricted branch reads BG 45, 55, SH 55 only, from 2001. Within this TI29 intersection it applies to BG 55 and SH 55 only: remove the throttle trigger via 8.1, then remove the wire from the trigger pivot pin. BG 45 is retained as source context, not added to the TI29 model binding.
- The other branch reads BG 65, 85, SH 85 from 2001 only: remove the wire from the housing peg. This is not the trigger-pivot-pin route. The page does not assign these two restricted routes to earlier versions or give an exact 2001 changeover.
- Under All BG/SH units, pull the retainers off the ignition lead and take the wires out of the illustrated guides in the inner fan housing. Reassemble in reverse sequence and push the wires fully home in the guides. The general instruction does not erase the model/version restrictions above it. The source does not identify which individual wire is removed from each pivot/peg in those branch captions; no wire color, gauge, length or pin-number mapping is inferred.
- The component manual requires the instruction manual safety precautions and applicable local regulations for any engine run. Fuel work is outdoors only, away from fire, flame, sparks or heat; wipe up spilled fuel immediately. These are source-reviewed reference notes, not a complete repair instruction or hardware verification. Exact owner-manual and remaining component dependencies stay open.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 component dependency; later2005 BG/SH 55, 65, 85: later short-circuit and ground-wire routing.
Later manual evidence: STIHL Series 4140 Components BG, SH service manual (2005-01), section BG/SH 55, 65, 85: later short-circuit and ground-wire routing, PDF pages 1, 3, 4, 12, 19, 20, 21
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: later tank-vent replacement variants
The manual overlaps “up to 2002” and “from 2002”; grommet and sealing-ring versions remain distinct without a serial cutoff.
- Later component evidence: January 2005, not a contemporaneous 1999 instruction or proof of original equipment. The introduction covers BG 45/46/55/65/85 and SH 55/85; this TI29-linked note is limited to BG 55/65/85 and SH 55/85 and the explicitly stated component variants. Catalog assembly links are navigation, not proof that all revisions fit.
- Section 9.5.2, printed 33 / PDF34, calls for vent replacement if pressure does not equalize. Remove the filter housing via 9.1.1 and note the vent installed position. Unlike the incorrect carburetor-removal reference elsewhere,9.1.1 includes filter-housing removal; it is not corrected to the choke section 9.1.2.
- For machines labeled up to 2002, pull out the vent and then its grommet. Install in reverse sequence. For machines labeled from 2002, carefully pry out the vent together with its sealing ring, always use a new sealing ring, and install in reverse sequence. The middle-column new-ring sentence continues the from 2002 branch.
- The source includes 2002 in both labels and gives no exact date or serial boundary. Inspect the actual vent assembly; do not normalize the overlap to before/after 2002 or infer interchangeability. Grommet and sealing ring are distinct illustrated items, not established substitutes. No vent, ring or grommet number, insertion depth or torque is supplied. Assembly destinations show related housing families, not a verified changeover or fit for every catalog revision.
- The component manual requires the instruction manual safety precautions and applicable local regulations for any engine run. Fuel work is outdoors only, away from fire, flame, sparks or heat; wipe up spilled fuel immediately. These are source-reviewed reference notes, not a complete repair instruction or hardware verification. Exact owner-manual and remaining component dependencies stay open.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 component dependency; January2005 later tank-vent replacement variants.
Later manual evidence: STIHL Series 4140 Components BG, SH service manual (2005-01), section later tank-vent replacement variants, PDF pages 1, 3, 4, 22, 34
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: later integral fuel tank and cleaning
The fuel tank is integral with the inner fan housing; damage requires that complete housing, not a separately replaceable tank.
- Later component evidence: January 2005, not a contemporaneous 1999 instruction or proof of original equipment. The introduction covers BG 45/46/55/65/85 and SH 55/85; this TI29-linked note is limited to BG 55/65/85 and SH 55/85 and the explicitly stated component variants. Catalog assembly links are navigation, not proof that all revisions fit.
- Section 9.6.1, printed 33 / PDF34: the fuel tank forms part of the inner fan housing and cannot be replaced separately. If damaged, replace the complete inner fan housing. This does not identify a replacement housing number or establish interchange between housing revisions or BG/SH models.
- The diaphragm pump draws fuel through the hose and pickup-body filter. Fine filter pores can clog with dirt, restricting flow and causing starvation. For fuel-supply trouble, check the tank and pickup body first and clean the tank if necessary. Pickup-body removal 9.6.2 and fuel hoses 9.6.3 are reviewed in separate notes; the general tank note does not replace those access procedures.
- For cleaning, observe the fuel-system precautions in section 2, unscrew the filler cap and drain the tank; add a small amount of clean gasoline, close the tank and shake the machine vigorously, then open and drain it again. Dispose of fuel properly. The source supplies no volume, solvent substitution, dwell time or present-day repair method for a damaged tank. No fuel handling or hardware test was performed.
- The component manual requires the instruction manual safety precautions and applicable local regulations for any engine run. Fuel work is outdoors only, away from fire, flame, sparks or heat; wipe up spilled fuel immediately. These are source-reviewed reference notes, not a complete repair instruction or hardware verification. Exact owner-manual and remaining component dependencies stay open.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 component dependency; January2005 later integral fuel tank and cleaning.
Later manual evidence: STIHL Series 4140 Components BG, SH service manual (2005-01), section later integral fuel tank and cleaning, PDF pages 1, 3, 4, 34
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: later fuel pickup-body service
The pickup-body filter is drawn out with the specified hook and checked for contamination; no filter interchange or cleaning method is supplied.
- Later component evidence: January 2005, not a contemporaneous 1999 instruction or proof of original equipment. The introduction covers BG 45/46/55/65/85 and SH 55/85; this TI29-linked note is limited to BG 55/65/85 and SH 55/85 and the explicitly stated component variants. Catalog assembly links are navigation, not proof that all revisions fit.
- Section 9.6.2, printed 34 / PDF35: unscrew the filler cap and drain the tank. Use hook 5910 893 8800 to draw the pickup body out of the tank. Pull the pickup body off its fuel hose, check for contamination and replace if necessary. Install in reverse sequence.
- The hook is a historical servicing tool, not a fuel-system replacement part. The page supplies no pickup-body number, filtering grade, replacement interval or cleaning method for the filter itself. The preceding tank-cleaning instructions do not authorize washing the pickup filter or deleting it. No hose-length or insertion-depth value is given.
- The component manual requires the instruction manual safety precautions and applicable local regulations for any engine run. Fuel work is outdoors only, away from fire, flame, sparks or heat; wipe up spilled fuel immediately. These are source-reviewed reference notes, not a complete repair instruction or hardware verification. Exact owner-manual and remaining component dependencies stay open.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 component dependency; January2005 later fuel pickup-body service.
Later manual evidence: STIHL Series 4140 Components BG, SH service manual (2005-01), section later fuel pickup-body service, PDF pages 1, 3, 4, 16, 35
Part numbers (1)
- 5910 893 8800 — Hook for pickup bodyWithdraw pickup body through tank opening · January2005 fuel pickup-body service; not a replacement filter
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: later fuel-hose removal and layout limits
Fuel-hose service retains the installed position and a wrong starter reference; the following fan-access column is not silently made a hose-removal step.
- Later component evidence: January 2005, not a contemporaneous 1999 instruction or proof of original equipment. The introduction covers BG 45/46/55/65/85 and SH 55/85; this TI29-linked note is limited to BG 55/65/85 and SH 55/85 and the explicitly stated component variants. Catalog assembly links are navigation, not proof that all revisions fit.
- Section 9.6.3, printed 34 / PDF35, middle column: unscrew the filler cap and drain the tank, remove the fan housing with rewind starter, remove the carburetor via 9.2.2, remove the pickup body and pull off the tank vent via 9.5.2. Pull out the fuel hoses as illustrated, note their installed position and reinstall in reverse sequence.
- The housing/starter instruction prints reference 7.2, but 7.2 is rope rotor/pawl; fan housing with rewind starter is section 7.1. The earlier reviewed starter-access note supplies that context. Preserve the printed cross-reference error without requiring a rotor/pawl teardown for hose access.
- The middle column ends with reverse assembly. The unheaded right column then discusses spark-plug removal, piston locking and model-specific outer fan-housing removal, continued on the next page under 10.1 Fanwheel. Its placement before that heading is retained as a layout ambiguity; the separate fan procedure is reviewed in its own later-manual note. Do not silently append piston locking or fanwheel removal to the fuel-hose procedure.
- No hose number, length, bore, routing dimensions, sealant, substitute material or hose interchange is supplied here. The drawing indicates withdrawal and installed position, not a fully dimensioned routing specification. Vent variants remain subject to their overlapping 2002 labels; catalog housing links do not select a machine revision.
- The component manual requires the instruction manual safety precautions and applicable local regulations for any engine run. Fuel work is outdoors only, away from fire, flame, sparks or heat; wipe up spilled fuel immediately. These are source-reviewed reference notes, not a complete repair instruction or hardware verification. Exact owner-manual and remaining component dependencies stay open.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 component dependency; January2005 later fuel-hose removal and layout limits.
Later manual evidence: STIHL Series 4140 Components BG, SH service manual (2005-01), section later fuel-hose removal and layout limits, PDF pages 1, 3, 4, 16, 35
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Wrong number or missing part for the SH 85? Report a correction →