← TS 410, TS 420

Stihl 4238 · Section G · 7 of 13 · 51 parts

Carburetor C1Q-S118C, C1Q-167A

Fits TS 410, TS 420.

Parts diagrams →

Historical fitment & changes (9) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11011121313131313141414141415161617181922021222324252627282929331323334353637383944041414243444546474856789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (51)

PosPart numberDescriptionQty
1 4116 121 5100 Inlet needle 1
2 1129 122 3001 Spring 1
3 1125 121 5000 Inlet control lever 1
4 1120 121 9200 Spindle 1
5 1120 122 6600 Collar screw 1
6 4238 129 0901 Gasket 1
7 4238 121 4700 NLA Metering diaphragm 1
8 4238 120 0850 NLA End cover Fitment / change note → 1
9 1120 122 6601 Collar screw 4
10 4238 120 7300 Air valve shaft with lever 1
11 4238 122 3202 Torsion spring Fitment / change note → 1
12 4238 122 3201 NLA Torsion spring Fitment / change note → → replaced by 4238 122 3202 TI 22/2009 1
13 4238 121 9400 Ring 5
14 4238 122 3600 Sealing ring 5
15 4238 121 6601 Lever 1
16 1139 122 7101 Screw 2
17 4180 121 3301 Throttle shutter 1
18 1125 122 7402 Round head screw 1
19 1123 121 7800 Strainer 1
20 1129 121 4800 Pump diaphragm 1
21 1123 129 0905 Gasket 1
22 4134 121 0802 End cover 1
23 1125 122 4200 Clamp 1
24 4229 122 6200 Idle speed adjustment screw 1
25 1120 122 7800 Oval head screw 1
26 4238 120 7100 Throttle shaft with lever 1
27 1123 122 3000 Spring 1
28 4238 121 3300 Throttle shutter 1
29 1125 122 7403 Round head screw 2
31 4238 121 6600 Lever 1
32 4238 122 9000 E-clip 1
33 4238 124 2100 Rod 1
34 1125 122 9003 E-clip 1
35 4238 120 7200 Choke shaft with lever 1
36 4238 122 3200 Torsion spring 1
37 1120 122 9000 E-clip 1
38 4128 121 2900 Choke shutter 1
39 4238 122 6800 Low speed adjustment screw 1
40 4238 122 6701 NLA High speed adjustment screw Fitment / change note → 1
41 4238 120 9800 NLA High speed adjusting screw/fixed jet kit Fitment / change note → 1
42 4238 121 5601 NLA Fixed jet 0.70 Fitment / change note → 1
43 4229 121 2701 Cap 1
44 4238 120 9700 Pump piston kit 1
45 4238 121 5602 Fixed jet 0.76 1
46 4238 121 0801 End cover 1
47 4238 121 4701 Metering diaphragm 1
48 4238 122 6702 High speed adjustment screw 1
Not numbered on the diagram — assemblies, kits and options
— 4238 120 0600 Carburetor C1Q-S118C Fitment / change note → 1
— 4238 120 0601 Carburetor C1Q-S167A 1
— 4238 007 1062 Set of carburetor parts 1
— 4238 007 1060 NLA Set of carburetor parts Fitment / change note → 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · TS 410 / TS 420

TS 410 / TS 420: two throttle shutters and the 35-degree boundary

The fuel-free-air shutter opens later through a slotted linkage.

  • The fuel-air path has shutter (1); the fuel-free-air path has shutter (2). Throttle rod (3) links them through actuating lever (4). Its oblong hole (5) delays opening of the fuel-free-air shutter; it is functional lost motion, not evidence of a missing fixed linkage.
  • The table describes idle (a) as BOTH shutters completely closed. At part throttle (b), mixture-shutter opening LESS THAN 35 degrees leaves the fuel-free-air shutter completely closed. At GREATER THAN 35 degrees, that shutter opens progressively with increasing load. At full throttle (c), BOTH are completely open.
  • Exactly 35 degrees is NOT dispositioned by the printed table. Do not silently turn its strict inequalities into an inclusive adjustment threshold. The idle description is a principle-table statement, not a service setting or instruction to eliminate required idle airflow.
  • The source gives no linkage-length, bending, synchronization or idle-speed adjustment procedure here. The two carburetor paths must not be confused with the separate starting choke settings printed below the table.
  • Retained 2007 source guidance, not present-day stock availability. No numeric serial cutoff is supplied. No physical interchange test was performed.

Source: TI 37/2007, p. 7 — TS 410 / TS 420: two throttle shutters and the 35-degree boundary.

No additional parts-table entry added.

Service note · TS 410 / TS 420

TS 410 / TS 420: starting-choke symbols and printed timing conditions

The original pictograms and unusual warm/hot wording are retained without silently reversing them.

  • Section 1.3 uses THREE CHOKE PICTOGRAMS, not stamped Latin letters. Consult the original page for their exact shapes: first symbol for COLD engine; middle symbol for WARM; third symbol for HOT. Text-extraction letters c/e/o are not the literal control markings.
  • The middle/WARM condition explicitly includes an engine that has already run but is still cold, AND a hot engine switched off for LESS THAN 5 minutes. The third/HOT condition explicitly says a hot engine switched off for MORE THAN 5 minutes.
  • The printed less-than/more-than wording may be counterintuitive; it is preserved, NOT reversed or treated as a confirmed correction. Exactly 5 minutes is not specified. No number of pulls, throttle-lock sequence or complete starting procedure is provided here.
  • This is source-linked historical reference, not an unattended starting instruction. Use the exact machine operating instructions to establish the complete starting procedure; no engine was started for this review.
  • Retained 2007 source guidance, not present-day stock availability. No numeric serial cutoff is supplied. No physical interchange test was performed.

Source: TI 37/2007, p. 7 — TS 410 / TS 420: starting-choke symbols and printed timing conditions.

No additional parts-table entry added.

Service note · TS 410 / TS 420

TS 410 / TS 420: fuel capacity and limiter-dependent carburetor settings

Standard capped settings and uncapped basic settings must not be merged.

  • The mixture-lubricated engine uses gasoline and engine oil; section 2.2.1 explicitly refers to the INSTRUCTION MANUAL for the mixture. No numerical mixing ratio is printed here. Tank capacity is 26.0 oz (0.77 l).
  • The carburetor is an all-position diaphragm type with booster pump. STANDARD setting WITH high-speed limiter cap: L = 1 turn open; H = carefully turn COUNTERCLOCKWISE as far as the stop, MAXIMUM 3/4 turn. The H entry is not an instruction to turn 3/4 from a fully seated uncapped screw.
  • BASIC setting WITHOUT limiter cap: L = 1 turn open; H = 1.5 turns open. The two H conditions are different configurations, not interchangeable alternatives or permission to remove the limiter.
  • This table gives no limiter-removal/refitting sequence, warm-engine tuning sequence or altitude compensation. The page 15 kit is explicitly for C1Q-S118; navigation through the later shared C1Q-S118C / C1Q-167A catalog sheet does NOT establish these settings or kit compatibility for all later carburetors.
  • Retained English-USA 2007 source guidance, not present-day stock availability or proof for later variants. No numeric serial cutoff is supplied. No physical interchange test was performed.

Source: TI 37/2007, p. 10 · TI 37/2007, p. 11 · TI 37/2007, p. 15 — fuel capacity and limiter-dependent carburetor settings.

No additional parts-table entry added.

Service note · TS 410 / TS 420

TS 410 / TS 420: gasket kit, carburetor kit and application-specific consumables

Blank application cells are not permission to use every listed compound everywhere.

  • Gasket set 4238 007 1003 is for the SHORTBLOCK. Carburetor-parts set 4238 007 1060 is expressly for C1Q-S118; the later shared catalog title C1Q-S118C / C1Q-167A does not extend that kit claim to all variants.
  • Lubricating grease 0781 120 1111 (225 g tube) is listed for oil seals, sliding and bearing points. STIHL special lubricant 0781 417 1315 is for the rope-rotor bearing bore and rewind spring in the starter cover. Dirko HT RED 0783 830 2000 is for the engine pan and OUTSIDE of oil seals.
  • Press Fluid OH 723 = 0781 957 9000; STIHL multi-purpose grease = 0781 120 1109; Loctite 242 = 0786 111 2101; Loctite 270 = 0786 111 2109; Loctite 648 = 0786 111 2117. Each of these rows has a BLANK USE CELL on the original page. Do not borrow an adjacent row’s use or treat the three Loctite products as interchangeable.
  • The unnumbered standard solvent-based degreasant must contain NO CHLORINATED OR HALOGENATED HYDROCARBONS. Its listed use is cleaning mating faces and carburetor, crankshaft stub and flywheel cone. No order number, blend, cure schedule or substitution specification is printed.
  • Retained English-USA 2007 source guidance, not present-day stock availability or proof for later variants. No numeric serial cutoff is supplied. No physical interchange test was performed.

Source: TI 37/2007, p. 15 — gasket kit, carburetor kit and application-specific consumables.

Part numbers (10)
  • 4238 007 1003 — Gasket setShortblock · TS 410 / TS 420; source restrictions apply
  • 4238 007 1060 — Carburetor parts setC1Q-S118 only as printed · TS 410 / TS 420; source restrictions apply
  • 0781 120 1111 — Lubricating grease, 225 gOil seals, sliding and bearing points · TS 410 / TS 420; source restrictions apply
  • 0781 417 1315 — STIHL special lubricantRope rotor bore and rewind spring · TS 410 / TS 420; source restrictions apply
  • 0781 957 9000 — Press Fluid OH 723Use cell blank · TS 410 / TS 420; source restrictions apply
  • 0781 120 1109 — STIHL multi-purpose greaseUse cell blank · TS 410 / TS 420; source restrictions apply
  • 0783 830 2000 — Dirko HT redEngine pan and seal exterior · TS 410 / TS 420; source restrictions apply
  • 0786 111 2101 — Loctite 242Use cell blank · TS 410 / TS 420; source restrictions apply
  • 0786 111 2109 — Loctite 270Use cell blank · TS 410 / TS 420; source restrictions apply
  • 0786 111 2117 — Loctite 648Use cell blank · TS 410 / TS 420; source restrictions apply

Service note · TS 410 / TS 420

TS 410 / TS 420: repair allowances: included leak, fuel and circuit tests

The included tests and failure-cause repair are part of the printed allowances.

  • The same trained-personnel, properly-equipped-shop scope and MINUTES apply. Rows 11–15: (11) replace crankcase/gasket or reseal crankcase, INCLUDING air-leak test = 160; (12) crankshaft main bearing(s), INCLUDING air-leak test = 170; (13) crankshaft seal(s), INCLUDING air-leak test = 70; (14) engine air-leak test alone = 30; (15) cylinder and/or piston, INCLUDING air-leak test AND repair of components causing failure = 90.
  • Rows 16–20: (16) ignition module or flywheel replacement, INCLUDING stop-circuit test = 25; (17) fuel-tank line, vent line or pickup-body replacement = 40; (18) intake/transfer-port manifold or intake-flange replacement = 35; (19) carburetor repair/replacement, INCLUDING fuel-system testing = 45; (20) rewind-starter repair/replacement = 15.
  • An included test must not be silently dropped or automatically charged twice by summing a standalone test row. These allowances do not supply leakage pressures, test durations, electrical limits, tightening torques or a full diagnostic sequence.
  • Retained English-USA 2007 source guidance, not present-day stock availability or proof for later variants. No numeric serial cutoff is supplied. No physical interchange test was performed.

Source: TI 37/2007, p. 16 — repair allowances: included leak, fuel and circuit tests.

No additional parts-table entry added.

Service note · TS 410 / TS 420

TS 410 / TS 420: same carburetor number, S118 to S118A to S118B

Read the marked index; the order number does not identify the internal revision.

  • Complete carburetor 4238 120 0600 keeps the SAME order number through two stages: C1Q-S118 to C1Q-S118A adds the new end cover and torsion spring; C1Q-S118A to C1Q-S118B adds the new fixed jet and high-speed screw. Figure 370TI045 locates S118 / S118 A / S118 B on the carburetor body; the adjacent XXXX X is not a supplied production serial.
  • Summary rows 1/2 include end-cover/spring items 3,5 versus 4,5; rows 6/7 include jet/screw items 8,10 versus 9,10, with other parts as previously. Prior S118 version is no longer factory available; S118A remains available UNTIL the S118B becomes available. New complete versions can also be used on older machines, subject to component service notes.
  • The retained exact-model IPL sheet is titled C1Q-S118C, C1Q-167A. This is a navigation anchor, NOT evidence that this TI covers the later C or167A variants. No settings or component equivalence are inferred for those later variants. Summary continuous introduction is not a serial cutoff for the carburetor stages.
  • Historical English 2009 source for TS 410 and TS 420, series 4238; supply statements are not present-day stock claims. No physical interchange test was performed.

Source: TI 22/2009, p. 1 · TI 22/2009, p. 2 · TI 22/2009, p. 7 — same carburetor number, S118 to S118A to S118B.

Part numbers (1)
  • 4238 120 0600 — C1Q-S118 / S118A / S118B carburetorUnchanged order number; inspect marked index · TS 410 / TS 420; source revision and pairing restrictions apply

Service note · TS 410 / TS 420

TS 410 / TS 420: carburetor end cover and torsion spring must match

The replacement end cover includes the new spring; old springs remain for old covers.

  • End cover 4238 121 0800 is replaced by 4238 120 0850, which INCLUDES new torsion spring 4238 122 3202 replacing 4238 122 3201. Figure 370TI046 shows previous pair TOP and new pair BOTTOM, with changed compensator-hose connection shape and spring alignment at the compensator connector.
  • Previous end cover is no longer available. New end cover INCLUDING new spring can also be used on previous C1Q-S118. New cover 4238 120 0850 may ONLY be used with new spring 4238 122 3202; previous spring 4238 122 3201 may ONLY be used with previous cover 4238 121 0800.
  • Old spring remains available for carburetors retaining the old cover. No mixed old/new cover-and-spring pair is authorized; no later C/167A applicability is established.
  • Historical English 2009 source for TS 410 and TS 420, series 4238; supply statements are not present-day stock claims. No physical interchange test was performed.

Source: TI 22/2009, p. 2 · TI 22/2009, p. 3 · TI 22/2009, p. 7 — carburetor end cover and torsion spring must match.

Part numbers (4)
  • 4238 121 0800 — End coverPrevious · TS 410 / TS 420; source revision and pairing restrictions apply
  • 4238 120 0850 — End cover including new torsion springNew; paired replacement · TS 410 / TS 420; source revision and pairing restrictions apply
  • 4238 122 3201 — Torsion springOnly previous cover · TS 410 / TS 420; source revision and pairing restrictions apply
  • 4238 122 3202 — Torsion springOnly new cover · TS 410 / TS 420; source revision and pairing restrictions apply

Service note · TS 410 / TS 420

TS 410 / TS 420: 70-marked jet and high-speed screw are a paired conversion

Use the complete kit for unconverted S118/S118A carburetors.

  • Previous fixed jet 4238 121 5600, marked 65 with Ø 0.65 mm bore, becomes 4238 121 5601, marked 70 with Ø 0.70 mm bore. Figure 370TI047 locates the marking: read it after removing end cover, metering diaphragm AND gasket. This is identification, not an instruction to drill out the old jet.
  • High-speed screw 4238 122 6700 becomes 4238 122 6701. Both old jet and old screw are no longer available. For C1Q-S118 and C1Q-S118A retaining the old pair, replace with high-speed adjusting screw kit 4238 120 9800, containing BOTH new jet 4238 121 5601 and new screw 4238 122 6701. New jet may ONLY be used with the new high-speed screw.
  • New jet and screw are available INDIVIDUALLY for C1Q-S118B AND earlier S118/S118A carburetors ALREADY CONVERTED to both new parts. Individual supply for a converted carburetor is not permission to mix a new jet with the old screw. Summary remarks 5/6 and kit items 9/10 preserve this qualification.
  • Historical English 2009 source for TS 410 and TS 420, series 4238; supply statements are not present-day stock claims. No physical interchange test was performed.

Source: TI 22/2009, p. 3 · TI 22/2009, p. 7 — 70-marked jet and high-speed screw are a paired conversion.

Part numbers (5)
  • 4238 121 5600 — Fixed jet marked 65 /0.65mmPrevious · TS 410 / TS 420; source revision and pairing restrictions apply
  • 4238 121 5601 — Fixed jet marked 70 /0.70mmNew; only with new screw · TS 410 / TS 420; source revision and pairing restrictions apply
  • 4238 122 6700 — High-speed screwPrevious · TS 410 / TS 420; source revision and pairing restrictions apply
  • 4238 122 6701 — High-speed screwNew; paired with new jet · TS 410 / TS 420; source revision and pairing restrictions apply
  • 4238 120 9800 — High-speed adjusting screw kitBoth new jet and screw · TS 410 / TS 420; source revision and pairing restrictions apply

Service note · TS 410 / TS 420

TS 410 / TS 420: settings depend on converted jet and limiter-cap state

H is 1.5 turns without the limiter cap, versus 3/4 turn with it.

  • These settings apply to C1Q-S118B AND previous C1Q-S118/C1Q-S118A in which BOTH new fixed jet 4238 121 5601 and high-speed screw 4238 122 6701 have already been installed. Do NOT apply them solely because complete carburetor order number 4238 120 0600 matches, or to an unconverted older carburetor.
  • BASIC setting WITHOUT limiter cap on high-speed screw H: low-speed L = 1 turn open; high-speed H = 1.5 turns open.
  • STANDARD setting WITH limiter cap on high-speed screw H: L = 1 turn open; H = 3/4 turn open, MAXIMUM NO FURTHER THAN STOP. Do not combine the uncapped 1.5-turn value with the capped standard setting. No idle rpm, maximum-speed test, emissions procedure or later S118C/167A settings are supplied in this TI.
  • Historical English 2009 source for TS 410 and TS 420, series 4238; supply statements are not present-day stock claims. No physical interchange test was performed.

Source: TI 22/2009, p. 4 — settings depend on converted jet and limiter-cap state.

Part numbers (2)
  • 4238 121 5601 — New fixed jetRequired configuration · TS 410 / TS 420; source revision and pairing restrictions apply
  • 4238 122 6701 — New high-speed screwRequired configuration · TS 410 / TS 420; source revision and pairing restrictions apply

Wrong number or missing part for the TS 410, TS 420? Report a correction →