← P 835, P 840

Stihl 4702 · Section O · 14 of 14 · 28 parts

Fuel tank

Fits P 835, P 840.

Parts diagrams →

Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
110111213141516171819220212223242534567789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (28)

PosPart numberDescriptionQty
1 4702 350 0405 Fuel tank 1
2 1119 084 8300 Reflector foil 1
3 1117 350 5800 Tank vent → replaced by 0000 350 5802, 0000 350 5800 TI 5/2002 1
4 1120 358 8105 Vent insert 2
5 0000 350 3500 Pickup body 1
6 not sold separately Hose 3.1x5.7x135 mm, R3 not available as a separate item 1
7 4205 122 2500 Hose clip 2
8 4702 358 7700 Hose 1
9 1111 353 2500 Elbow connector 1
10 0000 350 0520 Filler cap → replaced by 1127 350 0500 TI 48/1995 1
11 0000 359 1220 Sealing ring 1
12 0000 350 0900 Rope 1
13 0000 353 0600 Hook 1
14 4702 792 9301 Rubber buffer 4
15 4702 353 8705 Washer 4
16 9099 021 3760 Self-tapping screw 4.8x13 4
17 9022 341 1350 Spline screw IS-M6x25 3
18 4702 353 8705 Washer 3
19 4702 792 8301 Bushing 3
20 4702 353 2900 Rubber buffer 3
21 4702 353 8700 Washer 3
22 0000 967 3704 Warning pictogram 1
23 1107 890 3400 Combination wrench Fitment / change note → 1
24 0812 370 1000 Screwdriver T27x120x70 1
25 1107 191 1201 Locking screw 1
Not numbered on the diagram — assemblies, kits and options
— 0000 930 2803 Hose 3.1x5.7 mm x 1 m, R3 not illustratedoption 1
— 0712 923 8004 Hose 3.1x5.7 mm x 10 m, R3 not illustratedoption 1
— 4702 890 1405 Tool kit 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · P 835 / P 840

P 835 / P 840: historical fuel system settings and oil-dependent mixture

H and L are each approximately one turn; original oil distinctions remain explicit.

  • All-position diaphragm carburetor has integral fuel pump. Standard H high-speed and L low-speed adjusting screws are EACH backed off APPROXIMATELY ONE TURN. No carburetor model, final speed setting or limiter-removal instruction is given; do not silently bind these values to later carburetor variants.
  • Carburetor leakage-test gauge pressure 0.4 bar (5.8 psi); no hold time or acceptable leak rate stated. Fuel tank 2.65 litres (2650 cm³); minimum octane 90 RON, not 90 AKI.
  • Historical fuel specification: regular brand-name gasoline with brand-name two-stroke engine oil; mix 1:50 WITH STIHL two-stroke engine oil 1:50, but 1:40 WITH OTHER brand-name two-stroke engine oils. Preserve that source distinction rather than choosing one universal ratio. Round air filter with foam. This is the March 1994 specification, not an assertion about every modern oil or fuel formulation.
  • Historical TI 20/1994 guidance for explicitly named models only; no successor or unlisted variant applicability inferred. Factory supply statements are historical, not current stock claims. MOQ columns are order quantities, not fitting quantities. No physical interchange test was performed.

Source: TI 20/1994, p. 3 — P 835 / P 840: historical fuel system settings and oil-dependent mixture.

No additional parts-table entry added.

Service note · P 835 / P 840

P 835 / P 840: model weights, common dimensions and service accessories

Original total weights differ; carburetor and gasket kits have separate numbers.

  • Printed TOTAL weight: P 835 8.4 kg; P 840 7.9 kg. Source does not state a wet/dry weighing condition; do not invent one. Dimensions H×W×D are 380×350×300 mm, common table entry, not a mounting-hole template.
  • Accessories: combination wrench 1107 890 3400; screwdriver T27×120×70, number 0812 370 1145. Special service accessories: carburetor parts kit 4702 007 1060; set of gaskets 4702 007 1050. Kit contents, individual components and variant conversion are not specified; no such claims are inferred.
  • Historical TI 20/1994 guidance for explicitly named models only; no successor or unlisted variant applicability inferred. Factory supply statements are historical, not current stock claims. MOQ columns are order quantities, not fitting quantities. No physical interchange test was performed.

Source: TI 20/1994, p. 5 — P 835 / P 840: model weights, common dimensions and service accessories.

Part numbers (4)
  • 1107 890 3400 — Combination wrenchaccessory · P 835 / P 840: model weights, common dimensions and service accessories
  • 0812 370 1145 — T27×120×70 screwdriveraccessory · P 835 / P 840: model weights, common dimensions and service accessories
  • 4702 007 1060 — Carburetor parts kitservice accessory; contents unspecified · P 835 / P 840: model weights, common dimensions and service accessories
  • 4702 007 1050 — Set of gasketsservice accessory; contents unspecified · P 835 / P 840: model weights, common dimensions and service accessories

Wrong number or missing part for the P 835, P 840? Report a correction →