← 064/066 · MS 660 · MS 650/640

Stihl 1122 · Section A · 1 of 14 · 35 parts

Crankcase

Fits 064.

Parts diagrams →

Historical fitment & changes (4) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11101112131415161718192202122232425262728293303132333444567889
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (35)

PosPart numberDescriptionQty
1 1122 020 2101 Crankcase Fitment / change note → 1
2 9022 341 1300 Spline screw IS-M6x20 2
3 0000 988 5211 Connector 1
4 9371 470 2610 Cylindrical pin 5x18 2
5 0000 974 1200 Notched pin 2.6x8 1
6 1120 162 5200 Pin 1
7 1121 162 5205 Pin 1
8 1121 162 5200 Pin 2
9 1128 640 9100 Valve 1
10 9503 003 6676 Grooved ball bearing 6203 1
11 9523 003 4555 Grooved ball bearing 17x40x14 1
12 0000 953 6605 Collar screw M8 2
13 9022 371 1020 Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 6
14 1128 084 8302 Reflector foil 1
15 1122 021 1105 Cover Fitment / change note → 1
16 9022 313 0660 Spline screw IS-M4x12 Fitment / change note → 4
17 1122 664 2200 Cover plate 1
18 1122 664 4500 Support 1
19 9640 003 1850 Oil seal 17x32.9x3.6 1
20 9640 003 1355 Oil seal 13.5x20x4 Fitment / change note → 1
21 1122 029 0500 Gasket 1
22 1122 030 0407 Crankshaft Fitment / change note → → replaced by 1122 030 0408 TI 2/1996 1
23 1120 036 8500 Woodruff key 2x3.7 1
24 1122 647 9400 Hose 1
25 1117 640 3800 Pickup body 1
26 0000 350 0520 Filler cap → replaced by 1127 350 0500 TI 48/1995 1
27 0000 359 1220 Sealing ring 1
28 0000 350 0900 Rope 1
29 0000 353 0600 Hook 1
30 1122 021 1900 Plug 1
31 1125 084 8900 Grommet 1
32 0000 992 6302 Sealing ring 1
33 1117 350 0905 Filler cap retainer 1
34 9099 021 2360 Self-tapping screw 3.5x9.5 1
Not numbered on the diagram — assemblies, kits and options
— 1122 007 1051 Set of gaskets 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Historical fitment · 064

064: original parts retained through the 066 revision

The summary preserves original crankshaft, seal and collar-nut versions as spares for 064; it does not approve new 066 parts.

  • Remark 3 applies to crankshaft item 2, seal item 4 and original collar-nut item 7: original versions remain available as spares for older machines and model 064.
  • The seal row places remark 3 beside the new seal, but the wording explicitly concerns the ORIGINAL version. Section 1.2 and rows 3–4 identify that original as BS 13.5×20×4, 9640 003 1355; the remark is not evidence that the larger seal fits 064.
  • No 064 production range, full crankcase interchange or new 066 crankshaft/flywheel fitment is established. This is historical spare retention, not present availability.

Source: TI 2/1996, p. 1 · TI 2/1996, p. 4 — Summary items 2,4,7 / remark 3 with original seal relationship in 1.2.

Part numbers (3)
  • 1122 030 0407 — Original crankshaftHistorical spare retention · 064 per remark 3
  • 9640 003 1355 — Original oil seal BS 13.5×20×4Historical spare retention · 064; original version specified by remark 3
  • 0000 955 0802 — Original collar nut M8×1Historical spare retention · 064 per remark 3

Service note · 064 / 066

064 / 066: thirteen-roller crankshaft differs between production and service

066 gets the new crankshaft at X 29 588 002; 064 retains its production crankshaft but uses the new service replacement.

X 29 588 002 (066 production only) — Printed introduction for this component only; not a universal machine cutoff or interchange guarantee.

  • Crankshaft 1122 030 0407 with newly developed big-end bearing cage increases needle rollers from TWELVE to THIRTEEN. It becomes standard in 066 production FROM X 29 588 002. This serial is NOT a 064 production changeover.
  • 064 CONTINUES production with crankshaft 1122 030 0406, but 1122 030 0407 SHOULD be used for service replacement. Summary footnote says original crankshaft is no longer available FROM FACTORY; retain this spare-supply statement separately from its explicit continued 064 production use.
  • No separate bearing-cage part number or permission to rebuild the old crankshaft with loose new rollers is supplied. No MS 640 / MS 660 applicability is inferred.
  • Historical TI 19/1994 guidance for explicitly named models only; no successor or unlisted variant applicability inferred. Factory supply statements are historical, not current stock claims. MOQ columns are order quantities, not fitting quantities. No physical interchange test was performed.

Source: TI 19/1994, p. 1 — 064 / 066: thirteen-roller crankshaft differs between production and service.

Part numbers (2)
  • 1122 030 0406 — Original twelve-roller crankshaft064 production continues; unavailable factory spare · 064 / 066: thirteen-roller crankshaft differs between production and service
  • 1122 030 0407 — Thirteen-roller crankshaft066 production and 064 service replacement · 064 / 066: thirteen-roller crankshaft differs between production and service

Service note · 064 / 066

064 / 066 brake-band cover: fourth screw and smaller core hole

Cover 1122 021 1105 replaces 1101; recess changes from 4 to 3 mm.

X 31 815 798 — 064 / 066 crankcase, cover mounting and brake-spring revisions in TI27/1995; model-conditioned production change, not a universal compatibility boundary.

  • From X 31 815 798, crankcase 1122 020 2101 (064) and 1122 020 2102 (066) are revised. Both crankcases KEEP THEIR PART NUMBERS; a matching number alone cannot distinguish the original and modified castings.
  • Cover 1122 021 1105 replaces 1122 021 1101 and is secured with FOUR IS-M4 x 12 spline screws 9022 313 0660 instead of three. Figure 134TI004 K points to the added attachment near the brake band.
  • The recess at the brake-band attachment changes from diameter 4 mm to 3 mm (printed 5/32 to 1/8 inch) and becomes the CORE HOLE for the additional mounting point. This is a production geometry change, NOT a direction to drill an existing 4-mm recess smaller. No old-case conversion or machining method is given.
  • The TI says the change optimizes brake-band location; it gives no measured brake performance, screw torque or additional retrofit approval. Do not infer that the later cover alone makes every old crankcase equivalent.
  • Later exact 064 A sheet lists crankcase 2101 at key1, cover 1105 at key15 and screw 0660 quantity4 at key16. Exact 066 A sheet lists crankcase 2113 at key1 AND 2102 at key32, cover 1105 at key14 and screw 0660 quantity4 at key15. These later rows do not establish a 2102-to-2113 supersession or erase the historical same-number revision.
  • Historical TI guidance for the named models and stated versions only. Shared IPL sheets or series do not extend applicability to other variants or successor models. Supply statements are historical, not present stock guarantees or verified physical interchange. No hardware operation was performed.

Source: TI 27/1995, p. 1 — Section1 geometry and figure 134TI004 K.

Part numbers (5)
  • 1122 020 2101 — 064 crankcasesame-number revised casting · 064 / 066; Section1 geometry and figure 134TI004 K
  • 1122 020 2102 — 066 crankcasesame-number revised casting · 064 / 066; Section1 geometry and figure 134TI004 K
  • 1122 021 1101 — Original coverreplaced · 064 / 066; Section1 geometry and figure 134TI004 K
  • 1122 021 1105 — Four-screw covernew · 064 / 066; Section1 geometry and figure 134TI004 K
  • 9022 313 0660 — Spline screw IS-M4 x 12same number; installed quantity three to four · 064 / 066; Section1 geometry and figure 134TI004 K

Service note · 064 / 066

064 / 066 crankcase supply: cover and screws through end 1998

Preserve the dated crankcase inclusion limit; MOQ cells are blank.

X 31 815 798 — 064 / 066 crankcase, cover mounting and brake-spring revisions in TI27/1995; model-conditioned production change, not a universal compatibility boundary.

  • Both 064 crankcase 1122 020 2101 and 066 crankcase 1122 020 2102 are listed with original and new numbers IDENTICAL, each including summary item1 cover and item2 screw. Remark1: only MODIFIED crankcases are factory available. This does not prove that every used part bearing the number is modified.
  • Cover 1122 021 1101 is replaced by 1122 021 1105, remarks2 and3. Remark2: original cover no longer factory available. Screw 9022 313 0660 keeps its number, remarks3 and4. Remark4: quantity changes from THREE TO FOUR; this is installed quantity, not an order minimum.
  • Remark3 says the new version of the part WILL BE INCLUDED WITH CRANKCASE ONLY UP TO END OF 1998. It applies to both cover and screw rows. It is an inclusion deadline, NOT a claim that the cover and screws are supplied only as a crankcase kit, nor a standalone-availability promise after 1998. The four-screw mounting requirement does not expire with the supply deadline.
  • All MOQ cells in this summary are BLANK; do not invent MOQ1 or MOQ4. All other parts as before. The production introduction X 31 815 798 is repeated below the table; no separate introduction date is given.
  • Historical TI guidance for the named models and stated versions only. Shared IPL sheets or series do not extend applicability to other variants or successor models. Supply statements are historical, not present stock guarantees or verified physical interchange. No hardware operation was performed.

Source: TI 27/1995, p. 1 — Section1 complete summary and remarks1–4.

Part numbers (5)
  • 1122 020 2101 — 064 crankcasemodified-only factory supply · 064 / 066; Section1 complete summary and remarks1–4
  • 1122 020 2102 — 066 crankcasemodified-only factory supply · 064 / 066; Section1 complete summary and remarks1–4
  • 1122 021 1101 — Original coverno longer factory available · 064 / 066; Section1 complete summary and remarks1–4
  • 1122 021 1105 — Modified coversummary1; inclusion through end1998 · 064 / 066; Section1 complete summary and remarks1–4
  • 9022 313 0660 — Spline screw IS-M4 x 12summary2; inclusion through end1998; quantity4 · 064 / 066; Section1 complete summary and remarks1–4

Wrong number or missing part for the 064? Report a correction →