← 064/066 · MS 660 · MS 650/640

Stihl 1122 · Section B · 2 of 14 · 19 parts

Cylinder

Fits 064.

Parts diagrams →

Historical fitment & changes (3) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
110111213141515161718234556789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (19)

PosPart numberDescriptionQty
1 1122 020 1203 Cylinder with piston Ø 52 mm — 84.9 cc 1
2 1122 030 2001 Piston Ø 52 mm — 84.9 cc 1
3 1122 034 3000 Piston ring Ø 52x1.2 mm — 84.9 cc 2
4 1108 034 1501 Piston pin 12x8x33 1
5 9463 650 1200 Snap ring 12x1 2
6 9022 371 1020 Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 4
7 1122 029 2300 NLA Cylinder gasket 0.5 mm 1
8 1122 029 2305 Cylinder gasket 1 mm 1
9 9512 003 3281 Needle cage 12x17x13 1
10 1125 007 1021 Spur gear / chain adjusting screw kit 1
11 9646 945 0490 O-ring 7x1.5 1
12 1125 640 1900 Tensioner slide 1
13 1125 664 1400 Thrust pad 1
14 1122 664 2200 Cover plate 1
15 9041 216 0630 Pan head screw M4x8 Fitment / change note → 2
16 1122 664 4500 Support 1
17 1128 664 1001 Inner side plate 0.9 mm Fitment / change note → → replaced by 1128 664 1002 TI 12/1994 1
18 1128 664 1002 NLA Inner side plate Fitment / change note → → replaced by 1128 664 1001, 1128 664 1001 TI 10/2007 option 1
Not numbered on the diagram — assemblies, kits and options
— 1122 007 1051 Set of gaskets 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Conditional replacement · 044 / 064 / 066

044 / 064 / 066: sprung side plate requires the revised cover

Side plate 1128 664 1001 changes to 1128 664 1002; new plate installation requires the matching new cover. The general cover row changes 1125 640 1700 to 1125 640 1701.

  • When fitting the revised sprung-tab side plate during a repair, the new-version chain sprocket cover must also be fitted. The tabs hold the guide bar during chain assembly; this is not approval to use the new plate with the original cover.
  • The separate 1122-group cover row applies ONLY to 044 and 066 with wrap-around handles. It does not extend that cover to 064 or every 044/066.
  • Original side plates remain available for original covers/older machines in this bulletin. Original covers are supplied only while existing stocks last; these are historical availability statements.
  • The source identifies new covers by integrally cast numbers 1122 648 0401 and 1125 648 0404. These are identification marks, not the 640-group cover ordering numbers or established ordering aliases. The prose does not explicitly pair each cast number to a summary row.
  • The illustrated installation removes the M4x8 pan-head screw and old plate, pushes the new plate over the bar studs, then seats it using a combination wrench and one short blow with a plastic mallet.
  • For the FIRST installation of a new side plate, the source says to mount the guide bar and cover and tighten the M8 nuts to about 15–20 Nm (11–15 lbf.ft). This historical seating step is not a universal torque specification for later models or normal recurring bar adjustment.
  • Illustrated removal fits an M8 nut to the rear bar stud, twists the combination-wrench screwdriver end about 45° counterclockwise under the plate, raises the wrench end about 10–15 mm (1/2 in), then removes the nut and plate. Preserve the illustrated orientation; no hardware operation is verified here.
  • Pan-head screw 9041 216 0630 is omitted in the revised arrangement, not globally discontinued: the summary says it remains a spare for other models.
  • Introduction is in progress, dated May 17, 1994, without a numeric serial cutoff. The seven explicitly named models do not establish applicability to successors, 046, or unlisted variants. Prior-TI references are bibliography, not inherited compatibility.

Source: TI 12/1994, p. 1 · TI 12/1994, p. 2 · TI 12/1994, p. 3 · TI 12/1994, p. 4 — Cover/side-plate service note, assembly/disassembly and model-qualified summary.

Part numbers (7)
  • 1128 664 1001 — Original side platePrevious version · Retained for original cover
  • 1128 664 1002 — Sprung-tab side plateNew version · Requires new-version cover
  • 1125 640 1700 — Chain sprocket coverPrevious general cover · Historical while-stocks-last availability
  • 1125 640 1701 — Chain sprocket coverNew general cover · Named models in general summary row
  • 9041 216 0630 — Pan-head screw M4x8Removed from new arrangement · Still a spare for other models
  • 1122 648 0401 — Integrally cast cover numberIdentification only · Not an ordering alias or explicit row mapping
  • 1125 648 0404 — Integrally cast cover numberIdentification only · Not an ordering alias or explicit row mapping

Historical fitment · 064

064: original parts retained through the 066 revision

The summary preserves original crankshaft, seal and collar-nut versions as spares for 064; it does not approve new 066 parts.

  • Remark 3 applies to crankshaft item 2, seal item 4 and original collar-nut item 7: original versions remain available as spares for older machines and model 064.
  • The seal row places remark 3 beside the new seal, but the wording explicitly concerns the ORIGINAL version. Section 1.2 and rows 3–4 identify that original as BS 13.5×20×4, 9640 003 1355; the remark is not evidence that the larger seal fits 064.
  • No 064 production range, full crankcase interchange or new 066 crankshaft/flywheel fitment is established. This is historical spare retention, not present availability.

Source: TI 2/1996, p. 1 · TI 2/1996, p. 4 — Summary items 2,4,7 / remark 3 with original seal relationship in 1.2.

Part numbers (3)
  • 1122 030 0407 — Original crankshaftHistorical spare retention · 064 per remark 3
  • 9640 003 1355 — Original oil seal BS 13.5×20×4Historical spare retention · 064; original version specified by remark 3
  • 0000 955 0802 — Original collar nut M8×1Historical spare retention · 064 per remark 3

Service note · 064 / 066

064 / 066: higher cylinder base requires matching longer screws

Cylinder/piston 1122 020 1208 keeps its number; original and revised hardware must not be mixed.

  • The higher cylinder base requires FOUR IS-M6 x 25 spline screws 9022 371 1350 instead of FOUR IS-M6 x 20 screws 9022 371 1300. The cylinder fin is shortened around the mounting screws. A combination of original and new versions is NOT permitted.
  • The summary keeps cylinder with piston 1122 020 1208 unchanged and includes new screw item 2. The part number alone cannot identify base height or approve either screw length. No torque value, cylinder diameter or separate 064/066 cylinder assignment is supplied; do not infer universal cylinder interchange from the two-model heading.
  • TI08/1994 names historical 064 and 066, series 1122, not later MS models. All six changes are in progress; no numeric serial cutoff is supplied. Publication date is January 31, 1994; 08.94 is the bulletin identifier, not an August production date. MOQ columns are commercial order quantities, not installed counts. No physical interchange test was performed.

Source: TI 8/1994, p. 1 — higher cylinder base requires matching longer screws.

Part numbers (3)
  • 1122 020 1208 — Cylinder with piston, same number across revisionunchanged number · higher cylinder base requires matching longer screws
  • 9022 371 1300 — IS-M6 x 20 spline screw, fouroriginal version · higher cylinder base requires matching longer screws
  • 9022 371 1350 — IS-M6 x 25 spline screw, fournew version · higher cylinder base requires matching longer screws

Wrong number or missing part for the 064? Report a correction →