← 064/066 · MS 660 · MS 650/640

Stihl 1122 · Section H · 8 of 17 · 12 parts

Wiring harness

Fits 066.

Parts diagrams →

Historical fitment & changes (3) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11011234566789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (12)

PosPart numberDescriptionQty
1 1121 440 1103 Short circuit wire 305 mm / 12.1'' 1
2 1122 440 2201 Ground wire 270 mm / 10 5/8'' 1
3 1122 442 0400 Insulating hose 100 mm / 4'' 1
4 1122 440 3007 Wiring harness Fitment / change note → 1
5 1122 440 3002 Wiring harness Fitment / change note → 1
6 0000 989 0812 Grommet 1
7 1122 440 3009 Wiring harness Fitment / change note → → replaced by 1122 440 3002 TI 37/1999 1
8 1122 440 3000 Wiring harness 1
9 1122 440 3005 Wiring harness 1
10 1122 440 3008 Wiring harness Fitment / change note → → replaced by 1122 440 3009 TI 2/1996 1
11 1122 440 3001 Wiring harness 1
Not numbered on the diagram — assemblies, kits and options
— 0751 010 1110 Lead 10 m / 33' not illustratedoption 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Historical fitment · 066

066: keep the three heating-harness branches distinct

The combined-heating harness changes, while handle-heating-only harness 1122 440 3007 continues.

X 33 917 066 — Introduction of this 066 wrap-handle modification; not a model-identification range or a cutoff for the standard flush-cut version.

  • Wiring harness 1122 440 3009 replaces carburetor-heating version 1122 440 3008 and can serve machines with both handle and carburetor heating.
  • Original harness 1122 440 3008 remains available for machines up to X 33 917 065. That inclusive old-machine boundary is separate from the new modification beginning at X 33 917 066.
  • Handle-heating-only machines continue to use 1122 440 3007. Do not substitute the combined-heating harness solely because the model name is 066.
  • The drawing shows harness layout, but does not provide a complete wiring diagram, pinout or electrical test procedure.

Source: TI 2/1996, p. 3 · TI 2/1996, p. 4 — 3 and summary item 13 / remark 1.

Part numbers (3)
  • 1122 440 3008 — Original carburetor-heating harnessRetained older-machine spare · Up to X 33 917 065
  • 1122 440 3009 — Combined-heating harnessRevised version · Handle AND carburetor heating
  • 1122 440 3007 — Handle-heating-only harnessUnchanged branch · Handle heating only

Conditional replacement · 066

066 arctic: matched generator, flywheel and heating harness

From serial 1 44 672 219, the two-winding heating revision requires matched component versions; old and new parts must not be mixed.

1 44 672 219 — Introduction of this 066 arctic heating revision only; not a model-identification range or a production-date decoder.

  • Handle heating output is increased from printed serial 1 44 672 219. Modified generator, flywheel and wiring harness are installed together; the handle and carburetor heating systems now operate independently. No numerical heat-output rating is supplied.
  • Generator 1128 404 3502 has two windings instead of the single winding of 1128 404 3501. The table assigns yellow winding: 0.8 Ω, handle heating; red winding: 0.6 Ω, carburetor heating. These are printed resistance values, not measured results or invented tolerance/temperature limits. The generator comparison shows the previous version at left and new version at right.
  • Flywheel 1122 400 1202 replaces 1122 400 1218 within the matched revision. Drawing 132TI000 KN labels previous magnet width 6 mm and new width 10.5 mm (printed 10,5 mm). These are magnet widths, not ignition air gaps, crankshaft taper sizes or setting instructions.
  • Wiring harness 1122 440 3002 replaces 1122 440 3009. Drawing 137TI049 KN shows previous above/new below; the extra wire connects the generator’s second winding to handle heating. This wording is retained alongside the yellow/red functional table, not used to reverse its assignments. Correct generator-wire assignment is determined by the connectors; no connector cavity numbering is supplied.
  • Section 5 and summary remark 2 prohibit mixing previous and new versions in one machine. The three replacement arrows are conditional on the matched configuration, not approval for individual mixed-version substitution. Summary remark 1 retains all three previous parts as available spares at the bulletin date; it does not relax the prohibition.
  • The model label 066 links the catalog sheet; all assertions here are restricted to 066 arctic. No extension to unheated 066, 064 or MS 660 is inferred from shared part numbers or catalog navigation. Historical TI37/1999 evidence, not current availability or physically verified interchange.

Source: TI 37/1999, p. 1 · TI 37/1999, p. 2 · TI 37/1999, p. 3 — Complete pages 1–3, sections 1–6, all drawings, resistance table, summary, remarks and quiet regions.

Part numbers (6)
  • 1128 404 3501 — GeneratorPrevious matched configuration; remains available as spare · 066 arctic heating configuration only
  • 1128 404 3502 — GeneratorNew matched configuration; do not mix with previous versions · 066 arctic heating configuration only
  • 1122 440 3009 — Wiring harnessPrevious matched configuration; remains available as spare · 066 arctic heating configuration only
  • 1122 440 3002 — Wiring harnessNew matched configuration; do not mix with previous versions · 066 arctic heating configuration only
  • 1122 400 1218 — FlywheelPrevious matched configuration; remains available as spare · 066 arctic heating configuration only
  • 1122 400 1202 — FlywheelNew matched configuration; do not mix with previous versions · 066 arctic heating configuration only

Service note · 066

066 arctic: heating-wire routing and connector insulation

Center insulation over the connectors, route the harness under the ignition lead, and retain the short-circuit wire as illustrated for the matched heating revision.

  • This is section 6 wiring placement for the TI37/1999 066 arctic revision, not a complete electrical test, retrofit authorization or a replacement for the matched-component restriction: previous and new versions must not be mixed in one machine.
  • Drawing 137TI000 KN (page 3, upper left): center the insulating tubes over the connectors. Position generator wires in the recesses and between housing wall and rib. The arrows mark routing/insulation locations, not additional part-number callouts.
  • Drawing 137TI050 KN (page 3, lower left): pass the wiring harness UNDER the ignition lead. Fit the short-circuit wire in the ignition-module cable retainer until it snaps into position. Observe the illustrated installed position of the flat connector and terminal; no unprinted terminal angle, torque or polarity is inferred.
  • Drawing 137TI048 KN (page 3, upper right): position insulating tubes between rib and housing wall. Keep this placement distinct from the connector-centering requirement and generator-wire recess routing.
  • Section 5 says the connectors determine correct assignment of generator wires. The drawings do not supply a numbered pinout, wire-length specification or resistance-test setup. Follow the cited original views for physical orientation; no dimensions are estimated from illustration scale.
  • The model label 066 links the catalog sheet; all assertions here are restricted to 066 arctic. No extension to unheated 066, 064 or MS 660 is inferred from shared part numbers or catalog navigation. Historical TI37/1999 evidence, not current availability or physically verified interchange.

Source: TI 37/1999, p. 2 · TI 37/1999, p. 3 — Sections 5–6: connector assignment, all three routing drawings and matched-version restriction.

No additional parts-table entry added.

Wrong number or missing part for the 066? Report a correction →