← 064/066 · MS 660 · MS 650/640

Stihl 1122 · Section G · 7 of 17 · 31 parts

Ignition system

Fits 066.

Parts diagrams →

Historical fitment & changes (13) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
110111112131314141516161719220212324252627282829330455567899
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (31)

PosPart numberDescriptionQty
1 1122 400 1217 Flywheel Fitment / change note → 1
2 1122 400 1218 Flywheel Fitment / change note → → replaced by 1122 400 1202 TI 37/1999 1
3 1122 400 1202 Flywheel Fitment / change note → 1
4 1128 404 3501 Generator Fitment / change note → → replaced by 1128 404 3502 TI 37/1999 1
5 1118 431 6600 NLA Terminal pin no longer available from factory 1
6 1128 404 3502 Generator Fitment / change note → 1
7 1118 431 6700 NLA Terminal socket no longer available from factory 1
8 9022 313 0660 Spline screw IS-M4x12 Fitment / change note → 3
9 1121 442 0402 NLA Insulating hose 35 mm / 1.4'' Fitment / change note → 1
9 1121 442 0402 NLA Insulating hose 35 mm / 1.4'' Fitment / change note → 2
10 1121 405 1900 NLA Support 1
11 9211 260 1340 Hexagon nut M10x1 Fitment / change note → 1
12 1122 400 1314 Ignition module Fitment / change note → 1
13 0000 989 1010 Grommet Fitment / change note → 1
14 not sold separately Ignition lead 185 mm not available as a separate item 1
15 0000 448 1250 Lead retainer 1
16 1117 442 0905 Insulating hose 110 mm / 4.3'' 1
17 9022 341 1019 Spline screw IS-M5x20 3
19 0000 998 0604 Torsion spring 1
20 1128 405 1000 Spark plug boot 1
21 1128 084 1400 Cover 1
23 1128 404 3501 Generator Fitment / change note → → replaced by 1128 404 3502 TI 37/1999 1
24 1122 400 1214 NLA Flywheel Fitment / change note → 1
25 1122 400 1216 Flywheel Fitment / change note → 1
26 1122 404 3500 Generator Fitment / change note → → replaced by 1128 404 3501 TI 2/1996 1
27 9041 216 0540 NLA Pan head screw M3.5x12 Fitment / change note → 3
28 0000 955 0802 Collar nut M8x1 Fitment / change note → 1
29 1122 400 1307 Ignition module Fitment / change note → → replaced by 1122 400 1311 TI 51/1994 1
30 1122 448 1205 Lead retainer Fitment / change note → 1
Not numbered on the diagram — assemblies, kits and options
— 0000 405 0600 NLA Ignition lead 1 m option 1
— 0000 930 2251 Ignition lead 10 m option 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Historical fitment · 066

066 wrap handle: match flywheel and ignition module

The new red-wire module must not be mixed with the old flywheel, nor the old module with the new flywheel.

Later reviewed guidance: 066: replacement and old-stock modules require the previous 1303 configuration

X 33 917 066 — Introduction of this 066 wrap-handle modification; not a model-identification range or a cutoff for the standard flush-cut version.

  • Unheated flywheel 1122 400 1214 changes to 1122 400 1217; handle-heating (VH) flywheel 1122 400 1216 changes to 1122 400 1218. The new flywheel requires the new crankshaft and crankcase; the cover and section heading restrict this engine/ignition modification to wrap-handle 066.
  • The lightweight composite flywheel has a steel hub, polymer blades, magnesium starter-pawl bushing and high-performance magnets. The source reports approximately 15% weight reduction and reduced crankshaft mechanical load; these are historical design claims, not project measurements.
  • Ignition module 0000 400 1303 replaces 1122 400 1311 and is identified by its red ground wire instead of black. New module with old flywheel, or old module with new flywheel, is prohibited because starting and idle-running problems can result.
  • The new module air gap must be ≤0.5 mm (≤0.020 in). No lower bound or universal target setting is supplied. An incorrect gap raises the switching threshold and can prevent starting.
  • Availability conflict retained: section 2.2 says the old module has been deleted; summary item 9 carries remark 1 saying the original remains available as a spare for older machines. Neither statement is silently preferred, and neither establishes present stock.
  • The new module is compared with EY-V and refers to TI51/1994, which is retained but not reviewed in this batch. No additional EY-V behavior or timing curve is inferred from that reference.

Source: TI 2/1996, p. 2 · TI 2/1996, p. 4 — 2.1–2.2 and summary items 5,6,9 / remark 1.

Part numbers (6)
  • 1122 400 1214 — Original unheated flywheelOriginal pairing · 066 without handle-heating flywheel
  • 1122 400 1217 — Lightweight unheated flywheelNew pairing · Revised 066 wrap-handle engine set
  • 1122 400 1216 — Original VH flywheelOriginal heated pairing · 066 handle heating
  • 1122 400 1218 — Lightweight VH flywheelNew heated pairing · Revised engine and heater requirements
  • 1122 400 1311 — Black-ground-wire ignition moduleOriginal module · Original flywheel; availability wording conflicts
  • 0000 400 1303 — Red-ground-wire ignition moduleReplacement module · New flywheel only in this 066 revision

Historical fitment · 066

066: generator revision supports combined heating

Generator 1128 404 3501 replaces 1122 404 3500 with the lightweight-flywheel modification.

X 33 917 066 — Introduction of this 066 wrap-handle modification; not a model-identification range or a cutoff for the standard flush-cut version.

  • The higher-output generator permits handle heating and carburetor heating together. The bulletin gives no numeric electrical output, connector interchange test or stand-alone retrofit permission.
  • Introduction belongs to the wrap-handle engine/ignition modification. The crankcase generator seat also changes; matching the complete configuration remains required.
  • Summary remark 1 keeps the original generator available historically as a spare for older machines. This is not current availability or permission to mix old and new assemblies.

Source: TI 2/1996, p. 2 · TI 2/1996, p. 4 — 2.3 and summary item 10 / remark 1.

Part numbers (2)
  • 1122 404 3500 — Original generatorOriginal version · Older 066 configuration
  • 1128 404 3501 — Higher-output generatorNew version · Revised 066 configuration with combined heating capability

Historical fitment · 066

066: heated-flywheel retrofit requires both heater changes

Installing flywheel 1122 400 1218 on an older saw requires the new rear element and the revised front or wrap handle.

  • For a saw up to X 33 917 065 receiving flywheel 1122 400 1218, bond rear heating element 1128 434 5000 into the rear handle AND replace the original front/wrap handle with the new higher-resistance version. Identify front-handle versions by the +25°C resistance table.
  • This heating note does not waive the new-flywheel requirement for a matching new crankshaft and crankcase or matching ignition module. It is not permission to fit the new flywheel alone.
  • The source warns that new flywheel 1122 400 1218 combined with the original front/wrap handle or rear element 1125 434 5000 may burn out the heaters if run at full throttle for more than about four minutes at a time. Preserve this as a damage warning, not approval for a four-minute mismatched operating procedure.
  • The next service note expressly limits the original front/wrap handle and original rear element 1125 434 5000 to saws with flywheel 1122 400 1216. No adhesive product, bonding cure time or complete replacement procedure is specified here.

Source: TI 2/1996, p. 1 · TI 2/1996, p. 2 · TI 2/1996, p. 3 · TI 2/1996, p. 4 — Page 4 service notes, read with engine-set prerequisites in 1–2 and resistance table in 4.3.

Part numbers (4)
  • 1122 400 1218 — New VH flywheelConditional retrofit · Older 066 only with all engine/ignition/heater prerequisites
  • 1122 400 1216 — Original VH flywheelRequired original-heater pairing · Original front/wrap and rear heaters
  • 1125 434 5000 — Original rear heaterRestricted pairing · Flywheel 1122 400 1216 only
  • 1128 434 5000 — New rear heaterRequired retrofit companion · Bond into rear handle; replace front/wrap heater too

Historical fitment · 066

066: ignition fastener table retains a thread conflict

The summary labels the new nut M8×10, while the shaft text and drawing specify an M10 ignition-end thread.

X 33 917 066 — Introduction of this 066 wrap-handle modification; not a model-identification range or a cutoff for the standard flush-cut version.

  • Original collar nut 0000 955 0802 is labeled M8×1; new nut 9211 260 1340 is labeled M8×10 in the original summary. Page 1 explicitly changes the ignition-end thread from M8 to M10 and labels the drawing M10.
  • This original thread-label conflict is unresolved. Do not silently relabel the new nut, infer its pitch from the number, or treat M8×10 as a verified fit specification.
  • The table separately removes spline screw IS-M 3.5×12, 9041 216 0540, and introduces spline screw IS-M 4×12, 9022 313 0660. The table places them in the ignition-system chapter but gives no exact attachment point or tightening torque.
  • Remark 3 retains the original collar nut for older machines and 064. No comparable spare-availability remark is attached to either screw row; a dash in the new-version column is not a universal no-stock claim.

Source: TI 2/1996, p. 1 · TI 2/1996, p. 4 — 1.1 drawing/text and summary items 7,8,11,12 / remark 3.

Part numbers (4)
  • 0000 955 0802 — Original collar nut M8×1Original fastener · Older 066 configuration
  • 9211 260 1340 — New nut; printed M8×10 conflicts with M10 shaftUnresolved thread label · 066 revision; thread specification not verified
  • 9041 216 0540 — Spline screw IS-M 3.5×12Removed table version · Original ignition-system chapter
  • 9022 313 0660 — Spline screw IS-M 4×12New table version · Revised ignition-system chapter; attachment unspecified

Conditional replacement · 066

066: replacement and old-stock modules require the previous 1303 configuration

1122 400 1314 is the optimized replacement; existing 0000 400 1305 stock remains usable only within the printed 066 restriction.

1 33 017 966 — Printed prior-module restriction in TI22/1998; differs from the TI02/1996 wrap-handle revision serial. Not a universal 066 production range.

  • Both 0000 400 1305 and 1122 400 1314 are limited to 066 machines previously equipped with 0000 400 1303, printed as from machine number 1 33 017 966 with reference to TI02/1996. The earlier sentence permitting stock without reservation must be read with this explicit restriction.
  • The 046/066 branch originated with the lightweight polymer flywheel. New orders use 1122 400 1314; remaining 0000 400 1305 stock may be used in an eligible 066. The aluminium-flywheel 1300 branch is not a universal substitute.
  • All other 066 machine numbers are directed to Spare Parts for Previous Models in the parts list. No replacement for those configurations is invented here.
  • Printed serials differ: TI22/1998 gives 1 33 017 966 for this prior-module restriction, whereas the separately reviewed TI02/1996 record 066-wrap-flywheel-module-pairing-1996 preserves X 33 917 066 for the wrap-handle revision. Do not silently correct either or equate their differently scoped thresholds. The prior flywheel-pairing prohibition and availability conflict remain intact.
  • TI22/1998 reports isolated reliability problems with the former universal module on aluminium-flywheel machines. Different timing requirements led to two optimized modules; this is historical manufacturer field-test guidance, not a project hardware test.
  • Order only 0000 400 1300 or 1122 400 1314 according to the named model and restrictions. There is no automatic one-number replacement for 0000 400 1305.
  • The 02.98 microfiche/CD-ROM issue documents the future part numbers. Both summary rows say the original 0000 400 1305 is no longer available from the factory; that does not revoke the expressly permitted use of existing stocks on eligible 046/066 machines.
  • Introduction is in progress, without a new production cutoff. Factory availability is a 1998 statement, not current stock or proof of physical interchange.

Source: TI 22/1998, p. 1 · TI 22/1998, p. 2 — Sections 1–6: history, split, service note and ordering.

Part numbers (3)
  • 0000 400 1305 — Former universal ignition modulePermitted existing stock · 066 only within the previous-1303 restriction
  • 1122 400 1314 — Optimized polymer-flywheel ignition moduleNew-order replacement · 066 only within the previous-1303 restriction
  • 0000 400 1303 — Previous ignition moduleRequired prior configuration · 066 branch; from printed machine number 1 33 017 966

Historical fitment · 066

066: series 1122 replacement ignition assignment

1122 400 1314 and the listed flywheel pairings for series 1122; 205 mm ignition lead.

  • Standard: 1122 400 1314 with flywheel 1122 400 1217.
  • Heating: 1122 400 1314 with flywheel 1122 400 1218.
  • Printed ignition-lead length: 205 mm (8 1/16 in). Preserve the printed metric and inch values; no rounding correction is inferred.
  • TI01/1999 lists replacement combinations for the then-current machines, not every earlier configuration. Older machines are referred to Spare Parts for Previous Models in their own illustrated parts lists; no serial cutoff is supplied here.
  • Use only the listed ignition-module/flywheel combinations. The source warns that incorrect combinations can cause excessive RPM or running in reverse; sharing a module number does not make all flywheels interchangeable.
  • Universal replacement modules may differ from production modules in maker, shape and part number. The source describes installation/function compatibility within its assignments, not universal compatibility or a project hardware test.
  • Some replacement modules require shortening the ignition lead and/or short-circuit wire and crimping a different short-circuit connector. The table gives ignition-lead lengths only; it supplies neither a short-circuit-wire length nor a connector part number. Do not infer that every row needs modification.
  • Only the named models and printed series are covered. A shared IPL sheet does not extend this assignment to unnamed models or modern MS equivalents. This 1999 USA bulletin is historical guidance, not current availability.
  • TI22/1998 separately restricts 066 replacement to the previous 0000 400 1303 configuration, printing 1 33 017 966. TI02/1996 prints X 33 917 066 for its wrap-handle revision. These differently scoped serials and the earlier pairing/availability conflict remain unresolved; this table does not silently replace them.

Source: TI 1/1999, p. 1 · TI 1/1999, p. 2 — 1.1 general restrictions and 1.2.1 chainsaw assignments.

Part numbers (3)
  • 1122 400 1314 — Replacement ignition moduleAssigned replacement · 066, series 1122, only with the listed flywheel branch
  • 1122 400 1217 — Standard flywheelRequired pairing · 066, series 1122; standard only
  • 1122 400 1218 — Heating flywheelRequired pairing · 066, series 1122; heating only

Service note · 066

066: CDIC A to EY-V wiring and deleted LED

Separate ground/short circuit wires replace the original harness; heated-handle harness remains a distinct case.

X 31 067 164 — Ignition and flywheel modification for 064/066 only; NOT the earlier carburetor cutoffs.

  • Section 1.2 replaces governed CDIC A 1122 400 1307 with ungoverned EY-V 1122 400 1311, each including keys 8–9. Retainer 1122 448 1205 becomes 1125 448 1201; grommet 0000 989 1010 remains.
  • LED 1122 400 5000 (key 10), insulating tube 1121 442 0402 (11), and harness 1122 440 3000 (12) have dashes in the new column. Heated-handle harness 1122 440 3005 becomes 1122 440 3007 (13), NOT deletion of all heated wiring. Page 1 abbreviates the originals as 1122 440 3000/05.
  • New separate short circuit wire 1122 440 1101 (15), ground wire 1122 440 2201 (16) and insulating tube 1122 442 0400 (17) replace the harness arrangement. Original module, retainer, LED, tube and harnesses marked 1 remain available for older machines; new-column dashes do not mean globally unavailable.
  • MOQ 1 is printed for EY-V, new retainer, the old insulating tube, new short circuit and ground wires. The blank new-tube MOQ is not zero. Page 3 says the LED has no function with EY-V and MAY be removed and replaced by plug 1122 432 2300; this is optional closure, not an active replacement indicator.
  • The spline screw IS M5 x 20 remains 9022 371 1022, but remark 2 changes installed quantity from TWO to THREE. MOQ H is an order quantity, not an installed count; blank cells are not zero.
  • Converting CDIC/CDIC A to EY-V requires the NEW flywheel version and correct key slot (page 3); a module-only swap is not the printed conversion. The later 2012 ignition IPL uses other module/screw listings; no silent equivalence or supersession is inferred.
  • Historical TI 51/1994, dated December 15, 1994; not current stock, universal interchangeability or physical verification. No hardware operation was performed.

Source: TI 51/1994, p. 1 · TI 51/1994, p. 2 · TI 51/1994, p. 3 — 066: CDIC A to EY-V wiring and deleted LED.

Part numbers (15)
  • 1122 400 1307 — Original CDIC A moduleolder machines · 066 only in the exact version/configuration described here
  • 1122 400 1311 — New EY-V moduleincludes keys 8–9 · 066 only in the exact version/configuration described here
  • 1122 448 1205 — Original retainer; key 8older machines · 066 only in the exact version/configuration described here
  • 1125 448 1201 — New retainer; key 8MOQ 1 · 066 only in the exact version/configuration described here
  • 0000 989 1010 — Grommet; key 9unchanged · 066 only in the exact version/configuration described here
  • 1122 400 5000 — LED; key 10deleted in new version; older spares retained · 066 only in the exact version/configuration described here
  • 1121 442 0402 — Original insulating tube; key 11older machines; MOQ 1 · 066 only in the exact version/configuration described here
  • 1122 440 3000 — Original harness; key 12older machines · 066 only in the exact version/configuration described here
  • 1122 440 3005 — Original heated harness; key 13older machines · 066 only in the exact version/configuration described here
  • 1122 440 3007 — New heated-handle harness; key 13heated version only · 066 only in the exact version/configuration described here
  • 9022 371 1022 — Spline screw; key 14installed quantity 2 to 3 · 066 only in the exact version/configuration described here
  • 1122 440 1101 — Short circuit wire; key 15MOQ 1 · 066 only in the exact version/configuration described here
  • 1122 440 2201 — Ground wire; key 16MOQ 1 · 066 only in the exact version/configuration described here
  • 1122 442 0400 — New insulating tube; key 17new separate wiring · 066 only in the exact version/configuration described here
  • 1122 432 2300 — Plug for removed LEDoptional with EY-V · 066 only in the exact version/configuration described here

Service note · 066

066 USA/CDN: original module replaced by EY-V

Retainer and grommet stay unchanged; the new heated harness is not universal non-heated equipment.

X 31 067 164 — Ignition and flywheel modification for 064/066 only; NOT the earlier carburetor cutoffs.

  • Section 1.3 replaces 0000 400 1300 with 1122 400 1311. Do not conflate this old USA/CDN module with governed CDIC A 1122 400 1307 from section 1.2. Original 0000 400 1300 remains available for older machines; new EY-V MOQ 1.
  • Both include keys 18–19: retainer 1125 448 1201 and grommet 0000 989 1010 are unchanged. Spline screw 9022 371 1022, key 21, changes installed quantity from TWO to THREE; all other parts as before. The printed table skips key 20; do not invent a missing component.
  • Page 1 states that harness 1122 440 3007 will be installed in all versions WITH HEATED HANDLES. This does not extend the heated harness to every standard saw. The later 064 IPL also lists 0000 400 1300; that shared number does not change the TI’s USA/CDN 066 scope.
  • Historical TI 51/1994, dated December 15, 1994; not current stock, universal interchangeability or physical verification. No hardware operation was performed.

Source: TI 51/1994, p. 1 · TI 51/1994, p. 2 — 066 USA/CDN: original module replaced by EY-V.

Part numbers (6)
  • 0000 400 1300 — Original USA/CDN moduleolder machines · 066 only in the exact version/configuration described here
  • 1122 400 1311 — EY-V moduleincludes keys 18–19; MOQ 1 · 066 only in the exact version/configuration described here
  • 1125 448 1201 — Retainer; key 18unchanged · 066 only in the exact version/configuration described here
  • 0000 989 1010 — Grommet; key 19unchanged · 066 only in the exact version/configuration described here
  • 9022 371 1022 — Spline screw; key 21installed quantity 2 to 3 · 066 only in the exact version/configuration described here
  • 1122 440 3007 — Heated-handle harnessheated versions only · 066 only in the exact version/configuration described here

Service note · 064 / 066

064 / 066: EY-V 900 rpm cut-in and exact air-gap requirement

Starting cut-in is not idle speed or maximum speed; this TI gives no numeric air-gap dimension.

  • New-module features: practically no backfiring, defined cut-in RPM, retarded timing during starting and idle for smoother idling, longer burning spark than CDIC/CDIC A for improved flame propagation, and reliable combustion during starting. These are historical manufacturer claims, not measurements reproduced here.
  • The footnote attributes backfire suppression to modified timing and a defined cut-in speed of 900 rpm. This is NOT an idle setting, electronic speed limit, or guarantee of zero backfire.
  • The air gap MUST be maintained exactly; too wide a gap prevents reaching the cut-in threshold. NO NUMERIC AIR GAP is printed. Do not derive an adjustment dimension from the schematic or a similar module.
  • Historical TI 51/1994, dated December 15, 1994; not current stock, universal interchangeability or physical verification. No hardware operation was performed.

Source: TI 51/1994, p. 2 — 064 / 066: EY-V 900 rpm cut-in and exact air-gap requirement.

Part numbers (1)
  • 1122 400 1311 — EY-V module900 rpm starting cut-in, not governed maximum · 064/066 only in the exact version/configuration described here

Service note · 066

066: EY-V flywheel revision and X/B versus P key slots

Unchanged part numbers conceal a changed slot position and magnet material; conversion needs the modified flywheel.

X 31 067 164 — Ignition and flywheel modification for 064/066 only; NOT the earlier carburetor cutoffs.

  • Introduction of EY-V changes the flywheel key-slot position AND magnet material. Replacement flywheels differ from production-line flywheels by having a SECOND key slot, marked P and X. Do not assume every production wheel has two slots.
  • For repair, use slot X (sometimes marked B on 064) for modules WITHOUT speed cut-off; use slot P for electronically governed CDIC/CDIC A. Figure 134TI001 shows both ignition categories pointing to their corresponding keyways; it does not provide timing degrees or a machining procedure.
  • If CDIC/CDIC A is exchanged for EY-V 1122 400 1311, the flywheel MUST be replaced by the NEW version and installed in the correct slot. A matching old part number alone does not establish the revised geometry or magnet material.
  • 066 standard flywheel 1122 400 1214 and heated-handle flywheel 1122 400 1216 keep their numbers. Only modified versions are available from the factory at the TI date. Standard and heated wheels remain distinct; blank MOQ cells do not specify zero.
  • The later 2012 IPL retains these historical numbers but also lists other ignition equipment. No later-part supersession, timing compatibility or MS 640/MS 660 applicability is established by this TI.
  • Historical TI 51/1994, dated December 15, 1994; not current stock, universal interchangeability or physical verification. No hardware operation was performed.

Source: TI 51/1994, p. 3 — 066: EY-V flywheel revision and X/B versus P key slots.

Part numbers (3)
  • 1122 400 1214 — Standard flywheelsame number; modified version only · 066 only in the exact version/configuration described here
  • 1122 400 1216 — Heated-handle flywheelsame number; modified version only · 066 only in the exact version/configuration described here
  • 1122 400 1311 — EY-V conversion modulerequires new flywheel version · 066 only in the exact version/configuration described here

Service note · 066

066 revised flywheel: puller 1106 890 4501

Removal tool for the lightweight flywheel, subject to the original configuration limits.

X 33 917 066 — TI15/1997 service-note boundary for the referenced revised 066 configuration; not a universal flush-cut/064/successor cutoff.

  • Use puller 1106 890 4501 to REMOVE the lightweight flywheel. Drawing 137TI022 KN identifies the flywheel as (1) and puller as (2). The leading 1106 is the printed TOOL number prefix, not a model or series binding.
  • The source does not assign this puller to flywheel installation or to every old 066 flywheel. The drawing shows the puller acting at the hub; no tightening torque or substitute impact method is specified.
  • TI15/1997 applies these service notes to model 066 from machine number X 33 917 066 and explicitly refers to the TI02/1996 engineering changes: larger big-end bearing, wider-spaced crankcase bearings and lightweight flywheel. The notes supplement the 064, 066 shop manual; naming that joint manual does NOT extend the modification to 064 or MS successors.
  • Scope tension retained: TI15/1997 says 066 without repeating the handle qualifier; cited TI02/1996 sections 1 and 2 say WRAP HANDLE ONLY and exclude the standard flush-cut 066 Magnum at that date. Its summary says that version changes later but gives no date or cutoff. TI15 does not establish that later introduction. Identify the revised configuration; the serial alone is not proof of universal fitment. TI02 forbids mixing old/new crank-drive parts and requires the new crankshaft AND crankcase with the lightweight flywheel.
  • TI15 page 2 delegates detailed use of the special tools to the existing 064, 066 shop manual. That exact manual is not established in the verified local STIHL service documentation/owner PDF pools; detailed procedure remains a documented source gap. Later MS650/660 workshop material and the 2012 general tool catalogue are not treated as the missing historical manual. No unprinted torque, force, thread engagement, seal depth or complete repair sequence is supplied here. Last-TI08/1997 is bibliographic context, not a dependent procedure.
  • Tool numbers below are transcribed from the original scans; the retained extracted text has corrupted font-encoded digits. Originals and extraction remain unchanged. Historical source guidance only; no current availability, physical interchange or hardware execution established. No hardware operation was performed.

Source: TI 15/1997, p. 1 · TI 15/1997, p. 2 — 066 revised flywheel: puller 1106 890 4501.

Referenced bulletin evidence: TI 2/1996, p. 1 · TI 2/1996, p. 2 · TI 2/1996, p. 4 — Referenced configuration only: sections1.1/1.2/2.1 and summary remark2.

Part numbers (1)
  • 1106 890 4501 — Puller, drawing item 2Lightweight-flywheel removal · 066 revised configuration described in TI15/1997; ignition end only where specified

Conditional replacement · 066

066 arctic: matched generator, flywheel and heating harness

From serial 1 44 672 219, the two-winding heating revision requires matched component versions; old and new parts must not be mixed.

1 44 672 219 — Introduction of this 066 arctic heating revision only; not a model-identification range or a production-date decoder.

  • Handle heating output is increased from printed serial 1 44 672 219. Modified generator, flywheel and wiring harness are installed together; the handle and carburetor heating systems now operate independently. No numerical heat-output rating is supplied.
  • Generator 1128 404 3502 has two windings instead of the single winding of 1128 404 3501. The table assigns yellow winding: 0.8 Ω, handle heating; red winding: 0.6 Ω, carburetor heating. These are printed resistance values, not measured results or invented tolerance/temperature limits. The generator comparison shows the previous version at left and new version at right.
  • Flywheel 1122 400 1202 replaces 1122 400 1218 within the matched revision. Drawing 132TI000 KN labels previous magnet width 6 mm and new width 10.5 mm (printed 10,5 mm). These are magnet widths, not ignition air gaps, crankshaft taper sizes or setting instructions.
  • Wiring harness 1122 440 3002 replaces 1122 440 3009. Drawing 137TI049 KN shows previous above/new below; the extra wire connects the generator’s second winding to handle heating. This wording is retained alongside the yellow/red functional table, not used to reverse its assignments. Correct generator-wire assignment is determined by the connectors; no connector cavity numbering is supplied.
  • Section 5 and summary remark 2 prohibit mixing previous and new versions in one machine. The three replacement arrows are conditional on the matched configuration, not approval for individual mixed-version substitution. Summary remark 1 retains all three previous parts as available spares at the bulletin date; it does not relax the prohibition.
  • The model label 066 links the catalog sheet; all assertions here are restricted to 066 arctic. No extension to unheated 066, 064 or MS 660 is inferred from shared part numbers or catalog navigation. Historical TI37/1999 evidence, not current availability or physically verified interchange.

Source: TI 37/1999, p. 1 · TI 37/1999, p. 2 · TI 37/1999, p. 3 — Complete pages 1–3, sections 1–6, all drawings, resistance table, summary, remarks and quiet regions.

Part numbers (6)
  • 1128 404 3501 — GeneratorPrevious matched configuration; remains available as spare · 066 arctic heating configuration only
  • 1128 404 3502 — GeneratorNew matched configuration; do not mix with previous versions · 066 arctic heating configuration only
  • 1122 440 3009 — Wiring harnessPrevious matched configuration; remains available as spare · 066 arctic heating configuration only
  • 1122 440 3002 — Wiring harnessNew matched configuration; do not mix with previous versions · 066 arctic heating configuration only
  • 1122 400 1218 — FlywheelPrevious matched configuration; remains available as spare · 066 arctic heating configuration only
  • 1122 400 1202 — FlywheelNew matched configuration; do not mix with previous versions · 066 arctic heating configuration only

Service note · 066

066 arctic: heating-wire routing and connector insulation

Center insulation over the connectors, route the harness under the ignition lead, and retain the short-circuit wire as illustrated for the matched heating revision.

  • This is section 6 wiring placement for the TI37/1999 066 arctic revision, not a complete electrical test, retrofit authorization or a replacement for the matched-component restriction: previous and new versions must not be mixed in one machine.
  • Drawing 137TI000 KN (page 3, upper left): center the insulating tubes over the connectors. Position generator wires in the recesses and between housing wall and rib. The arrows mark routing/insulation locations, not additional part-number callouts.
  • Drawing 137TI050 KN (page 3, lower left): pass the wiring harness UNDER the ignition lead. Fit the short-circuit wire in the ignition-module cable retainer until it snaps into position. Observe the illustrated installed position of the flat connector and terminal; no unprinted terminal angle, torque or polarity is inferred.
  • Drawing 137TI048 KN (page 3, upper right): position insulating tubes between rib and housing wall. Keep this placement distinct from the connector-centering requirement and generator-wire recess routing.
  • Section 5 says the connectors determine correct assignment of generator wires. The drawings do not supply a numbered pinout, wire-length specification or resistance-test setup. Follow the cited original views for physical orientation; no dimensions are estimated from illustration scale.
  • The model label 066 links the catalog sheet; all assertions here are restricted to 066 arctic. No extension to unheated 066, 064 or MS 660 is inferred from shared part numbers or catalog navigation. Historical TI37/1999 evidence, not current availability or physically verified interchange.

Source: TI 37/1999, p. 2 · TI 37/1999, p. 3 — Sections 5–6: connector assignment, all three routing drawings and matched-version restriction.

No additional parts-table entry added.

Wrong number or missing part for the 066? Report a correction →