Stihl 1122 · Section K · 10 of 17 · 32 parts
Tank housing
Fits 066.
Historical fitment & changes (8) — includes parts and conditions not shown on this drawing.
Parts (32)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1122 350 0817 | Tank housing Fitment / change note → | 1 |
| 2 | 1122 353 9200 | Grommet | 1 |
| 3 | 0000 350 5802 | Tank vent | 1 |
| 4 | 1122 350 5803 | Tank vent Fitment / change note → | 1 |
| 5 | 1122 353 9102 | Connector | 1 |
| 6 | 1122 358 1800 | Filter | 1 |
| 7 | 1110 353 1600 | Valve Fitment / change note → | 1 |
| 8 | 1122 120 0104 | Carburetor housing Fitment / change note → | 1 |
| 9 | 1122 122 6602 | Collar screw | 2 |
| 10 | 9104 003 0650 | Self-tapping screw P4x10 | 7 |
| 11 | 1124 358 7700 | Hose | 1 |
| 12 | 0000 967 3662 | Warning pictogram MS | 1 |
| 13 | 0000 963 0808 | Bushing | 1 |
| 14 | 1122 350 0816 | Tank housing Fitment / change note → | 1 |
| 15 | 1122 120 0102 | Carburetor housing Fitment / change note → | 1 |
| 16 | 1122 350 5851 NLA | Tank vent Fitment / change note → | 1 |
| 17 | 1120 358 8105 | Vent insert Fitment / change note → | 1 |
| 18 | 1122 353 0200 NLA | Clamp Fitment / change note → | 1 |
| 19 | 1122 141 2201 | Manifold | 1 |
| 20 | 1122 141 1805 | Sleeve | 1 |
| 21 | 1128 121 8600 | Washer | 1 |
| 22 | 1128 791 8400 | Ring | 1 |
| 23 | 1122 790 9920 | Annular buffer 1122/20 | 1 |
| 24 | 9022 341 0980 | Spline screw IS-M5x16 | 1 |
| 26 | not sold separately | Hose 3.1x5.7x52 mm, R5 not available as a separate item | 1 |
| 27 | 0000 350 3504 | Pickup body | 1 |
| 28 | 0000 350 0509 | Filler cap | 1 |
| 29 | 0000 350 0900 | Rope | 1 |
| 30 | 0000 353 0600 | Hook | 1 |
| 31 | 0000 359 1203 | Sealing ring | 1 |
| 32 | 0000 359 1230 | Sealing ring | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 0000 937 5004 | Hose 3.1x5.7 mm x 1 m, R5 not illustratedoption | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Historical fitment · 066
066: identify revised heaters by resistance at 25°C
Higher-resistance front and rear heaters accompany the revision; the nonheated wrap handle is unchanged.
X 33 917 066 — Introduction of this 066 wrap-handle modification; not a model-identification range or a cutoff for the standard flush-cut version.
- Heated front handle 1122 790 1712 changes to 1122 790 1713. Wrap-around handle for handle AND carburetor heating changes from 1122 790 3604 to 1122 790 3607. Both new handle versions have higher-resistance heating elements.
- Wrap-around handle 1122 790 3603 continues for machines with neither handle nor carburetor heating; it is not one of the heated replacement handles.
- At +25°C (77°F), front-handle heating-element resistance is 1.44–1.76 Ω original and 6.3–7.7 Ω new. Rear-handle element resistance is 0.225–0.275 Ω original and 0.9–1.1 Ω new. These values are component- and temperature-specific, not whole-circuit limits.
- Rear element 1128 434 5000 replaces 1125 434 5000. The new element has thinner printed conductors running in wavy lines; the diagram identifies original on the left and new on the right.
- Original heated handles and rear element remain historical spares for older machines under remark 1, subject to the flywheel pairing restrictions. This 066 resistance table does not silently resolve the separate unit conflict in TI07/1995 for 044.
Source: TI 2/1996, p. 3 · TI 2/1996, p. 4 — 4.1–4.3 and summary items 14–16 / remark 1.
Part numbers (7)
- 1122 790 1712 — Original heated front handleOriginal heater · 066 handle heating
- 1122 790 1713 — Revised heated front handleHigher-resistance heater · 066 handle heating
- 1122 790 3604 — Original heated wrap handleOriginal heater · 066 handle and carburetor heating
- 1122 790 3607 — Revised heated wrap handleHigher-resistance heater · 066 handle and carburetor heating
- 1122 790 3603 — Nonheated wrap handleUnchanged · Neither handle nor carburetor heating
- 1125 434 5000 — Original rear heating elementOriginal heater · Old flywheel pairing only
- 1128 434 5000 — Revised rear heating elementHigher-resistance heater · New heated-flywheel configuration
Historical fitment · 066
066: heated-flywheel retrofit requires both heater changes
Installing flywheel 1122 400 1218 on an older saw requires the new rear element and the revised front or wrap handle.
- For a saw up to X 33 917 065 receiving flywheel 1122 400 1218, bond rear heating element 1128 434 5000 into the rear handle AND replace the original front/wrap handle with the new higher-resistance version. Identify front-handle versions by the +25°C resistance table.
- This heating note does not waive the new-flywheel requirement for a matching new crankshaft and crankcase or matching ignition module. It is not permission to fit the new flywheel alone.
- The source warns that new flywheel 1122 400 1218 combined with the original front/wrap handle or rear element 1125 434 5000 may burn out the heaters if run at full throttle for more than about four minutes at a time. Preserve this as a damage warning, not approval for a four-minute mismatched operating procedure.
- The next service note expressly limits the original front/wrap handle and original rear element 1125 434 5000 to saws with flywheel 1122 400 1216. No adhesive product, bonding cure time or complete replacement procedure is specified here.
Source: TI 2/1996, p. 1 · TI 2/1996, p. 2 · TI 2/1996, p. 3 · TI 2/1996, p. 4 — Page 4 service notes, read with engine-set prerequisites in 1–2 and resistance table in 4.3.
Part numbers (4)
- 1122 400 1218 — New VH flywheelConditional retrofit · Older 066 only with all engine/ignition/heater prerequisites
- 1122 400 1216 — Original VH flywheelRequired original-heater pairing · Original front/wrap and rear heaters
- 1125 434 5000 — Original rear heaterRestricted pairing · Flywheel 1122 400 1216 only
- 1128 434 5000 — New rear heaterRequired retrofit companion · Bond into rear handle; replace front/wrap heater too
Historical fitment · 066
066 wider housing and protected tank vent
Wider carburetor housing enlarges the filter compartment; tank volume increases about 5%. New vent 1122 350 5803 routes to a protected chamber in that housing.
Later reviewed guidance: 064 / 066: revised tank-vent package without the extra 044/046 ring
X 39 176 186 — TI01/1998 summary introduction of the described 066 modification; not a universal whole-saw interchange boundary.
- Tank housing 1122 350 0816 changes to 1122 350 0817 and includes carburetor housing item 29, changed 1122 120 0102 to 1122 120 0104. The about 5% volume increase is a source-relative claim; no absolute tank capacity is supplied.
- The new vent is routed to chamber 1 in the carburetor housing for dust/dirt protection. This routing is not evidence that the old housing accepts the new arrangement unchanged.
- Original vent 1122 350 5850 remains a spare for machines up to X39 176185; the summary separately limits original-vent availability to the end of 1999 (remark 5). Neither statement is a current-stock claim, and the old-machine limit is one serial below the modification introduction X39 176186.
- Original carburetor and tank housings remain available for older machines (prose; remark 1 in summary). The TI identifies 36/1997 as the introduction of the original vent and as last-TI bibliography; that retained bulletin is independently reviewed in the linked historical overlay (batch43), not closed by this reference alone. No missing procedure is required to interpret the locally printed change.
Source: TI 1/1998, p. 3 · TI 1/1998, p. 5 · TI 1/1998, p. 6 — Section4 including chamber drawing; summary items28–30 and remarks.
Part numbers (6)
- 1122 350 0816 — Tank housingOriginal version / historical spare status · 066; exact 1998 configuration and conditions apply
- 1122 350 0817 — Tank housingNew version · 066; exact 1998 configuration and conditions apply
- 1122 120 0102 — Carburetor housingOriginal version / historical spare status · 066; exact 1998 configuration and conditions apply
- 1122 120 0104 — Carburetor housingNew version · 066; exact 1998 configuration and conditions apply
- 1122 350 5850 — Tank ventOriginal version / historical spare status · 066; exact 1998 configuration and conditions apply
- 1122 350 5803 — Tank ventNew version · 066; exact 1998 configuration and conditions apply
Historical fitment · 066
066 switch shaft: shorter travel, changed number group
Switch shaft 1122 180 0905 is replaced by 1122 182 0902 for shorter switch travel; preserve the printed 180-to 182 number-group change.
X 39 176 186 — TI01/1998 summary introduction of the described 066 modification; not a universal whole-saw interchange boundary.
- The stated purpose is optimized switch movements with shorter travel; the TI gives no travel distance or adjustment procedure.
- Original switch shaft remains a spare under remark 1. This is not an instruction to normalize 1122 182 0902 to an 180-group number.
- The summary says all other parts as before and introduction from X39 176186. These statements describe this 066 modification, not shared-sheet 064/MS660 applicability or proof of universal parts interchange. The original cover names 066 despite the imported search title mentioning 064; footer 1998 and last TI36.97 are bibliographic, not review dates.
Source: TI 1/1998, p. 4 · TI 1/1998, p. 6 — Section6 and summary item43 / final notes.
Part numbers (2)
- 1122 180 0905 — Switch shaftOriginal version / historical spare status · 066; exact 1998 configuration and conditions apply
- 1122 182 0902 — Switch shaftNew version · 066; exact 1998 configuration and conditions apply
Conditional replacement · 064 / 066
064 / 066: revised tank-vent package without the extra 044/046 ring
1122 350 5851 replaces the earlier package; the added ring is not required on 064/066.
- Section 2 replaces complete tank vent 1122 350 5850 with 1122 350 5851 in connection with 044/046 changes. The summary says introduction is in progress, with no numeric serial. The previous complete vent is no longer available from the factory (remark 1); this is a 1999 supply statement.
- The new complete vent includes items 2–4: tank vent 1122 350 5802 and thrust ring 1122 353 0200 retain their numbers, while thrust ring 1128 353 0200 is added. Remark 2 requires the added 1128 ring only for 044 and 046; inclusion in the package is not a requirement to install it on 064/066.
- A detailed instruction sheet is supplied with the vent. It is not reproduced here and was not identified in the bounded 43-file retained docs inventory. Its full installation procedure remains a named source gap; do not infer it from this parts table. TI36/1997 is retained and pending separate review, not missing or automatically reviewed by this citation.
- TI01/1998 separately describes the later 066 protected-housing vent 1122 350 5803 and retains 1122 350 5850 for older machines. This 1999 replacement of that earlier package is not evidence to remove a protected-housing vent or retrofit every 066. Confirm the installed housing; no 1998 serial limit is silently reapplied as a new 1999 cutoff.
- Historical TI52/1999 instructions and spare-availability statements are not present stock or physical interchange verification. Base-model catalog sheets are navigation anchors; printed R/M variant restrictions remain controlling. No applicability to MS 640, MS 650 or MS 660 is inferred.
Source: TI 52/1999, p. 2 — Section 2, complete four-row summary and both remarks.
Part numbers (4)
- 1122 350 5850 — Complete tank vent, previousReplaced; no longer factory-supplied in this TI · 064 / 066 earlier tank-vent arrangement; not every 066 housing
- 1122 350 5851 — Complete tank vent, newIncludes items 2–4; installation is model-specific · 064 / 066 earlier tank-vent arrangement; not every 066 housing
- 1122 350 5802 — Tank vent componentUnchanged item 2 · 064 / 066 earlier tank-vent arrangement; not every 066 housing
- 1122 353 0200 — Thrust ringUnchanged item 3 · 064 / 066 earlier tank-vent arrangement; not every 066 housing
Service note · 064 / 066
064 / 066: 1997 tank vent and housing modification
TI36/1997 introduces vent 1122 350 5850 from X 38 139 451, with a 5.6 mm housing hole and unchanged housing numbers. Later 066 guidance is linked separately.
Later reviewed guidance: 066 wider housing and protected tank vent · 064 / 066: revised tank-vent package without the extra 044/046 ring
X 38 139 451 — Introduction of the described 064/066 tank-vent modification; not a universal model/part interchange boundary.
- The modified vent discharges into the gap between the carburetor housing and shroud. Introduction is from machine number X 38 139 451 for the named 064/066 modification; this is not a model-identification range or proof of interchange with later vents.
- Tank housing 1122 350 0816 (including summary items 1–6) and carburetor housing 1122 120 0102 retain their numbers. Only the modified housing versions were available from the factory. Numbers alone therefore do not identify the molding state; inclusion keys do not require refitting the deleted cap/filter.
- Service sequence, page 1: remove carburetor box cover and air filter; drill the carburetor housing at the molding skin indicated by the arrow, diameter 5.6 mm (printed 0.22 inch), then carefully remove drill shavings. No coordinate, substitute drilling location or added tolerance is supplied; use the original drawing, not a dimension inferred from its scale.
- Page 2: remove the old cap and filter; place the tank vent in position. Grip it with suitable pliers as illustrated and seat it by tapping the pliers once or twice with a mallet. Slip the thrust piece over the vent in the illustrated orientation.
- Page 3: use suitable pliers to press the thrust piece home by tapping once or twice with a mallet. Push the vent through the carburetor housing into the gap; install the air filter and carburetor box cover. The figures show where the pliers bear; no seating force, depth or torque is printed.
- The vent assembly 1122 350 5850 includes vent insert 1120 358 8105 and thrust piece 1122 353 0200 (items 3–4). The insert was already in inventory. Original cap 1121 358 2500 and filter 1121 358 1800 are deleted for this modification but remained available for other, unnamed models; that is not fitment evidence for any particular other model.
- The printed instruction to always install 1122 350 5850 as a replacement is bounded to this 1997 configuration. The same summary limits supply of that vent to the end of 1999. These statements do not prove current availability, or override the later 066 vent/housing revision and later 064/066 package guidance linked below.
- Last-TI entries 08/1997 for 064 and 15/1997 for 066 are bibliographic references, not missing prerequisites to this printed sequence. Historical instructions only; no physical retrofit or leak-test result is claimed.
Source: TI 36/1997, p. 1 · TI 36/1997, p. 2 · TI 36/1997, p. 3 — Complete service sequence, all illustrations, summary inclusion keys and four availability remarks.
Part numbers (7)
- 1122 350 0816 — Tank housing including items 1–6Same number, modified housing · 064 / 066; TI36/1997 configuration only
- 1122 120 0102 — Carburetor housingSame number, modified housing · 064 / 066; TI36/1997 configuration only
- 1122 350 5850 — Tank vent including insert and thrust pieceNew assembly / historically time-limited spare · 064 / 066; TI36/1997 configuration only
- 1120 358 8105 — Vent insertExisting inventory; vent assembly component · 064 / 066; TI36/1997 configuration only
- 1122 353 0200 — Thrust pieceVent assembly component · 064 / 066; TI36/1997 configuration only
- 1121 358 2500 — CapDeleted for this modification; other unnamed models only · 064 / 066; TI36/1997 configuration only
- 1121 358 1800 — FilterDeleted for this modification; other unnamed models only · 064 / 066; TI36/1997 configuration only
Service note · 064 / 066
064 / 066: larger pickup filter has different component stock limits
New complete pickup replaces the old one; old filter remains, but old weight and cap last only while stocks do.
X 29 412 876 — Printed introduction for this component only; not a universal machine cutoff or interchange guarantee.
- From X 29 412 876, pickup body 0000 350 3500 replaces 1115 350 3503 with a larger filter area to enhance operation and standardize parts. Original complete pickup is no longer factory-available. This cutoff is separate from the 066 crankshaft change at X 29 588 002.
- Drawing shows original pickup exploded into filter (1), weight (2) and cap (3), alongside new complete pickup. Original filter 1110 358 1800 REMAINS available for older machines; NEW filter is NOT separately available (-*- is not an order number). Original weight 1115 358 8200 and cap 1115 358 2500 remain supplied ONLY WHILE STOCKS LAST. Do not apply their stock-exhaustion limit to the retained original filter.
- No new weight/cap numbers or S-shaped-hose pairing are specified here. Other-model standardization is not permission for unlisted model interchange. Previous-TI pointer 08.94 is a reference, not another completed review. Original footer is March 11, 1994.
- Historical TI 19/1994 guidance for explicitly named models only; no successor or unlisted variant applicability inferred. Factory supply statements are historical, not current stock claims. MOQ columns are order quantities, not fitting quantities. No physical interchange test was performed.
Source: TI 19/1994, p. 2 — 064 / 066: larger pickup filter has different component stock limits.
Part numbers (5)
- 1115 350 3503 — Original complete pickup bodyno longer factory-available · 064 / 066: larger pickup filter has different component stock limits
- 0000 350 3500 — Larger-filter pickup bodynew complete replacement · 064 / 066: larger pickup filter has different component stock limits
- 1110 358 1800 — Original filter, item 1retained spare; new filter assembly-only · 064 / 066: larger pickup filter has different component stock limits
- 1115 358 8200 — Original weight, item 2while stocks last · 064 / 066: larger pickup filter has different component stock limits
- 1115 358 2500 — Original cap, item 3while stocks last · 064 / 066: larger pickup filter has different component stock limits
Service note · 064 / 066
064 / 066: one-way mushroom vent and retained-pressure warning
Tank housing number unchanged; cap/filter predate the valve change, with their own printed range.
X 35 661 524 — Tank valve modification only; cap/filter prior range separately retained.
- From X 35 661 524, mushroom valve 1110 353 1600 replaces original two-way valve 4114 353 1600 in tank housing 1122 350 0816. Housing includes items 2–4 (cap, filter, valve) and keeps its number; all other parts remain as before. Only the modified housing is factory supplied in this historical notice.
- Cap 1121 358 2500 and filter 1121 358 1800 keep their numbers. Remark 2 says these parts are ALREADY installed from X 34 687 772 TO X 35 661 523. This is the stated prior cap/filter range, not a second introduction of the mushroom valve or an ending serial for the unchanged cap/filter.
- Original two-way valve remains available FOR OTHER MODELS (remark 3), not an unrestricted alternative on this modification. The new mushroom valve is already in inventory (remark 4). No exact list of other models is supplied.
- Air enters through the new valve as fuel volume falls, but cannot flow from INSIDE OUTWARDS. Pressure can therefore build with the engine STOPPED if fuel is heated by sunlight or other influences. Source warning: always open the filler cap SLOWLY to release excess pressure gradually and avoid unexpected fuel escape. Better pressure equalization does not mean outward venting or a pressure-free tank.
- Figure145TI016 compares original1 and new2; arrows in145TI017 show inward flow. No opening pressure, vent-test value, machining instruction or complete retrofit procedure is given.
- Historical TI08/1997 evidence for the stated 064/066 configurations only. Independent modification cutoffs are not whole-model identification ranges, current stock claims or blanket retrofit permission. No MS640/MS660 successor scope or tested physical interchange is inferred. No hardware operation was performed.
Source: TI 8/1997, p. 1 · TI 8/1997, p. 2 — 064 / 066: one-way mushroom vent and retained-pressure warning.
Part numbers (5)
- 1122 350 0816 — Tank housing including cap/filter/valveUnchanged assembly number; modified contents · 064 / 066; only the described configuration
- 1121 358 2500 — Vent cap, item2Unchanged; earlier stated range · 064 / 066; only the described configuration
- 1121 358 1800 — Vent filter, item3Unchanged; earlier stated range · 064 / 066; only the described configuration
- 4114 353 1600 — Original two-way valveReplaced here; supply retained for other models · 064 / 066; only the described configuration
- 1110 353 1600 — New mushroom valveReplacement; already in inventory · 064 / 066; only the described configuration
Wrong number or missing part for the 066? Report a correction →