Stihl 1122 · Section M · 12 of 17 · 44 parts
Handlebar
Fits 066.
Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.
Parts (44)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1124 121 9100 | Bushing | 1 |
| 2 | 1122 120 0621 | Carburetor WJ-67A → replaced by 1122 120 0618 TI 27/2003 | 1 |
| 3 | 1122 120 0623 | Carburetor WJ-76A | 1 |
| 4 | 1122 120 0618 NLA | Carburetor WJ-69B | 1 |
| 5 | 1128 430 6002 | Heating element | 1 |
| 6 | 1128 430 0501 | Switch | 1 |
| 7 | 1118 431 6700 NLA | Terminal socket no longer available from factory | 1 |
| 8 | 1121 442 0402 NLA | Insulating hose 35 mm / 1.4'' | 2 |
| 9 | 1128 434 5101 | Heating element | 1 |
| 10 | 1118 431 6600 NLA | Terminal pin no longer available from factory | 1 |
| 11 | 1122 122 9300 | Clip | 1 |
| 12 | 1122 121 7000 NLA | Baffle | 1 |
| 13 | 9210 260 0700 | Hexagon nut M5 | 2 |
| 14 | 9771 021 2620 | Hose clip Ø 36x5 | 1 |
| 15 | 1122 790 1750 | Handlebar | 1 |
| 16 | not sold separately | Hose 460 mm / 18 1/8'' not available as a separate item | 1 |
| 17 | 9074 478 4435 | Pan head self-tapping screw IS-P6x19 Fitment / change note → | 2 |
| 18 | 9074 478 4475 | Pan head self-tapping screw IS-P6x21.5 | 2 |
| 19 | 9074 478 4675 | Pan head self-tapping screw IS-P6x32.5 Fitment / change note → | 2 |
| 20 | 1124 791 5105 | Stiffener Fitment / change note → | 1 |
| 22 | not sold separately | Handle hose 220 mm / 8 5/8'' not available as a separate item | 1 |
| 23 | not sold separately | Handle hose 380 mm / 15'' not available as a separate item | 1 |
| 24 | 9074 478 4435 | Pan head self-tapping screw IS-P6x19 Fitment / change note → | 2 |
| 25 | 9074 478 4475 | Pan head self-tapping screw IS-P6x21.5 | 1 |
| 26 | 9074 478 4675 | Pan head self-tapping screw IS-P6x32.5 Fitment / change note → | 1 |
| 27 | 9022 371 1020 | Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 | 1 |
| 28 | 9307 021 0120 | Washer 5.3 | 1 |
| 29 | 1122 791 5501 | Elbow connector | 1 |
| 30 | 1122 791 5500 | Elbow connector → replaced by 1122 790 3610, 1122 791 5501 TI 10/2008 | 1 |
| 31 | not sold separately | Handle hose 265 mm / 10 7/16'' not available as a separate item | 1 |
| 32 | not sold separately | Handle hose 370 mm / 14 9/16'' not available as a separate item | 1 |
| 33 | 9074 478 4435 | Pan head self-tapping screw IS-P6x19 Fitment / change note → | 1 |
| 34 | 1122 351 0901 | Guard | 1 |
| 35 | 9074 478 2970 | Pan head self-tapping screw IS-P4x10 | 1 |
| 36 | not sold separately | Wrap around handlebar optionno longer available from factory | 1 |
| 37 | not sold separately | Handle hose 420 mm / 16 1/2'' option | 1 |
| 38 | not sold separately | Handle hose 240 mm / 9 1/2'' option | 1 |
| 39 | 1122 791 4500 | Spacer option | 1 |
| 40 | 9074 478 4705 | Pan head self-tapping screw IS-P6x40 option | 2 |
| 41 | 9074 478 4435 | Pan head self-tapping screw IS-P6x19 Fitment / change note → option | 2 |
| 42 | 1124 890 3400 NLA | Combination wrench option | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 0000 791 2009 | Handle hose Ø 19 mm x 5 m / 3/4x197'' option | 1 |
| — | 1122 790 3650 | Wrap around handlebar | 1 |
| — | 1122 007 1003 | Set wrap around handlebar option | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Historical fitment · 066
066: identify revised heaters by resistance at 25°C
Higher-resistance front and rear heaters accompany the revision; the nonheated wrap handle is unchanged.
X 33 917 066 — Introduction of this 066 wrap-handle modification; not a model-identification range or a cutoff for the standard flush-cut version.
- Heated front handle 1122 790 1712 changes to 1122 790 1713. Wrap-around handle for handle AND carburetor heating changes from 1122 790 3604 to 1122 790 3607. Both new handle versions have higher-resistance heating elements.
- Wrap-around handle 1122 790 3603 continues for machines with neither handle nor carburetor heating; it is not one of the heated replacement handles.
- At +25°C (77°F), front-handle heating-element resistance is 1.44–1.76 Ω original and 6.3–7.7 Ω new. Rear-handle element resistance is 0.225–0.275 Ω original and 0.9–1.1 Ω new. These values are component- and temperature-specific, not whole-circuit limits.
- Rear element 1128 434 5000 replaces 1125 434 5000. The new element has thinner printed conductors running in wavy lines; the diagram identifies original on the left and new on the right.
- Original heated handles and rear element remain historical spares for older machines under remark 1, subject to the flywheel pairing restrictions. This 066 resistance table does not silently resolve the separate unit conflict in TI07/1995 for 044.
Source: TI 2/1996, p. 3 · TI 2/1996, p. 4 — 4.1–4.3 and summary items 14–16 / remark 1.
Part numbers (7)
- 1122 790 1712 — Original heated front handleOriginal heater · 066 handle heating
- 1122 790 1713 — Revised heated front handleHigher-resistance heater · 066 handle heating
- 1122 790 3604 — Original heated wrap handleOriginal heater · 066 handle and carburetor heating
- 1122 790 3607 — Revised heated wrap handleHigher-resistance heater · 066 handle and carburetor heating
- 1122 790 3603 — Nonheated wrap handleUnchanged · Neither handle nor carburetor heating
- 1125 434 5000 — Original rear heating elementOriginal heater · Old flywheel pairing only
- 1128 434 5000 — Revised rear heating elementHigher-resistance heater · New heated-flywheel configuration
Service note · 064 / 066
064 / 066: handle liner excludes wrap-around versions
Polymer stiffener fits between the handle and two longer mounting screws.
- EXCEPT versions with wrap-around handle. Fit polymer handle liner 1124 791 5105 between the front handle and spline screws, as illustrated. Two IS-P6 x 32.5 screws 9074 478 4675 replace two IS-P6 x 19 screws 9074 478 4435 at this mounting.
- The remark attached to the ORIGINAL short-screw row says its quantity changes from FOUR to TWO. This is not a change to only one mounting screw: the prose and both mounting-screw rows specify 2x. Do not treat MOQ H10/V50 for the new screws as installation quantities. The bulletin supplies no unrestricted retrofit or wrap-around fitment claim.
- TI08/1994 names historical 064 and 066, series 1122, not later MS models. All six changes are in progress; no numeric serial cutoff is supplied. Publication date is January 31, 1994; 08.94 is the bulletin identifier, not an August production date. MOQ columns are commercial order quantities, not installed counts. No physical interchange test was performed.
Source: TI 8/1994, p. 2 — handle liner excludes wrap-around versions.
Part numbers (3)
- 1124 791 5105 — Polymer handle linernew component · handle liner excludes wrap-around versions
- 9074 478 4435 — IS-P6 x 19 spline screworiginal mounting screw; remaining quantity 2 · handle liner excludes wrap-around versions
- 9074 478 4675 — IS-P6 x 32.5 spline screw, twonew mounting screw · handle liner excludes wrap-around versions
Wrong number or missing part for the 066? Report a correction →