← 064/066 · MS 660 · MS 650/640

Stihl 1122 · Section A · 1 of 16 · 28 parts

Crankcase

Fits MS 650.

Parts diagrams →

Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1110111213141516171819222021222324252627344567889
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (28)

PosPart numberDescriptionQty
1 1122 020 2116 Crankcase 1
2 1122 020 2113 Crankcase → replaced by 1122 020 2116 TI 10/2007 1
3 0000 988 5211 Connector 1
4 9371 470 2610 Cylindrical pin 5x18 2
5 0000 974 1200 Notched pin 2.6x8 1
6 1120 162 5200 Pin 1
7 1121 162 5205 Pin 1
8 1121 162 5200 Pin 2
9 1128 640 9100 Valve 1
10 9503 003 6676 Grooved ball bearing 6203 1
11 9523 003 4555 Grooved ball bearing 17x40x14 1
12 9022 371 1020 Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 6
13 1128 084 8302 Reflector foil 1
14 1138 664 2400 Collar screw 2
15 0000 953 6605 Collar screw M8 2
16 9640 003 1850 Oil seal 17x32.9x3.6 1
17 9640 003 1560 Oil seal 15x22x4 1
18 1122 029 0507 Gasket 1
19 1122 030 0408 Crankshaft 1
20 1120 036 8500 Woodruff key 2x3.7 1
21 1122 647 9400 Hose 1
22 1117 640 3800 Pickup body 1
23 0000 350 0520 Filler cap → replaced by 1127 350 0500 TI 48/1995 1
24 0000 359 1220 Sealing ring 1
25 0000 350 0900 Rope 1
26 0000 353 0600 Hook 1
27 1125 084 8900 Grommet 1
Not numbered on the diagram — assemblies, kits and options
— 1122 007 1053 Set of gaskets 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · MS 650

MS 650 serial location and separate parts-list requirement

MS 660 labor-time reuse is not blanket parts interchange.

  • The serial number is marked on the SIDE OF THE CRANKCASE at the arrow in figure 217TI008 KN, adjacent to the muffler/front-spike area. The figure gives a location, NOT a serial cutoff or identification interval.
  • The MS 660 repair timetable may be used for MS 650 only under the stated assumption of trained personnel in a properly equipped service workshop. No numeric labor allowances are printed here; none are reconstructed.
  • A SEPARATE MS 650 illustrated parts list is announced. This does not authorize treating MS 660 internal parts or repair procedures as identical. Existing MS 650 catalog sheets are the appropriate navigation anchors; whole-manual acceptance remains separate.
  • Historical TI10/2005 MS 650 guidance only; the linked catalog sheets are navigation anchors, not proof that all later variants share these specifications. No physical interchange test was performed.

Source: TI 10/2005, p. 7 — MS 650 serial location and separate parts-list requirement.

No additional parts-table entry added.

Service note · MS 361 / MS 362 / MS 440 / MS 441 / MS 460 / MS 650 / MS 660 / MS 880

MS 361, MS 362, MS 440, MS 441, MS 460, MS 650, MS 660, MS 880: magnesium stud adhesive changes to Loctite 270

Metric-thread crankcase studs: Loctite 243 (USA 242) → Loctite 270; not polymer housings.

  • Exact listed magnesium-crankcase models: MS 361, MS 362, MS 440, MS 441, MS 460, MS 650, MS 660, MS 880. Their metric-thread studs change from Loctite 243 (USA: Loctite 242) to Loctite 270. No stud part number, serial changeover, cure time or torque is specified here.
  • Before stud reassembly, clean BOTH threads: insert the tap into the internal thread BY HAND, then blow out the threaded hole; brush off the external stud thread. Coat the cleaned stud with Loctite 270. This thread-cleaning instruction is not permission to enlarge the polymer repair-stud hole.
  • Loctite is NOT used for studs in polymer engine housings. The magnesium adhesive change does not override the separate polymer repair restrictions or give these models permission to use the oversized polymer repair studs.
  • The repeated words engine housings at the end of page3 are present in the original scan; they add no second instruction and are not silently corrected in the retained source.
  • Historical English TI29/2011. Only the printed model and material scope is admitted; no unlisted variants or predecessor models are inferred. No physical interchange test was performed.

Source: TI 29/2011, p. 3 — MS 361, MS 362, MS 440, MS 441, MS 460, MS 650, MS 660, MS 880: magnesium stud adhesive changes to Loctite 270.

No additional parts-table entry added.

Wrong number or missing part for the MS 650? Report a correction →