← 084 · 088 · MS 780/880/881

Stihl 1124 · Section K · 10 of 14 · 28 parts

Air filter

Fits 088.

Parts diagrams →

Historical fitment & changes (5) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1101112131415161718192202122232424252627283456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (28)

PosPart numberDescriptionQty
1 1124 120 0609 Carburetor HT-12E 1
2 1124 123 7501 Grommet Fitment / change note → → replaced by 1124 123 7502 TI 9/2009 1
3 1124 123 7500 Grommet Fitment / change note → → replaced by 1124 123 7501 TI 40/1997 1
4 1124 121 9100 Bushing 1
5 1124 124 3420 Filter base 1
6 1124 120 2200 Flange 1
7 9121 319 0960 Stud M5x12x9 1
8 9216 261 0700 Hexagon nut M5 2
9 0000 120 1653 Air filter, wire mesh option 1
10 0000 140 4402 Air filter HD2 1
11 0000 141 0300 Prefilter Fitment / change note → 1
12 1124 141 0510 Filter cover Fitment / change note → 1
13 1124 140 9500 Twist lock 1
14 1128 141 4001 Slide 1
15 1124 182 1000 Throttle trigger 1
16 1117 182 4500 Torsion spring 1
17 9371 470 2640 Cylindrical pin 5x24 1
18 1117 182 0805 Lockout lever 1
19 1124 182 1500 Throttle rod → replaced by 1124 180 4050 TI 9/2009 1
20 1124 182 0900 Switch shaft 1
21 1124 182 0800 Double lever 1
22 1124 185 2000 Choke lever 1
23 1124 182 4400 Mount 1
24 9074 478 3076 Pan head self-tapping screw IS-P4x19 2
25 1124 182 1505 Throttle rod 1
26 1124 185 1900 Choke rod 1
27 1124 442 1600 Contact spring 1
28 1124 791 0600 Handle molding 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Historical fitment · 046 / 088

046 / 088: dry HD filter without inner foam

Dry fleece replacement, cleaning and model-specific foam rule.

  • Dry fleece HD filter 0000 120 1652 replaces oil-impregnated HD filter 0000 120 1650. The new filter carries the crossed-out OIL pictogram and does not need oil impregnation. This is not a blanket no-oil rule for the original filter or unrelated filter materials.
  • When cutting power noticeably drops, clean felt prefilter 0000 141 0300. After several prefilter cleanings, or if power remains low with a clean prefilter, remove the felt prefilter and clean the HD filter; carefully blow from the clean-air side if possible. On 044/064/066/084 also remove inner foam 0000 124 0800 for cleaning.
  • For stubborn dirt or caked fleece, wash filter parts in a clean non-flammable solution, such as warm soapy water. No air-pressure value, solvent recipe, drying duration or oiling step is supplied by this bulletin.
  • Fine trapped dirt may remain after cleaning and shorten cleaning intervals with extended use. Replace the filter when those intervals are no longer practical, or if thorough cleaning after long operation still leaves a noticeable cutting-power loss. No fixed service-hour limit or diagnosis excluding other causes is established.
  • Introduction is in progress, without a numeric cutoff. Original filter 0000 120 1650 was no longer supplied by the factory in this historical source, not a present stock assertion. An included instruction sheet is mentioned but is not reproduced or claimed reviewed here; the printed bulletin procedures above stand on their own.
  • Inner foam element 0000 124 0800 is included in the supplied HD filter but must be removed before installation in the new STIHL HD system, explicitly identified here as 046 and 088. Inclusion is not positive foam fitment. The 088 application is stated on page2 even though it is absent from the page1 model heading.
  • No later MS-model, every air-filter system or physical interchange claim is inferred from the shared part number.

Source: TI 43/1996, p. 1 · TI 43/1996, p. 2 — Both complete pages: dry fleece identification, cleaning, service life, installation and supply summary.

Part numbers (4)
  • 0000 120 1650 — Oil-impregnated HD air filterOriginal · 046 / 088
  • 0000 120 1652 — Dry fleece HD air filterReplacement · 046 / 088
  • 0000 141 0300 — Felt prefilterCleaning subject · 046 / 088
  • 0000 124 0800 — Inner foam elementRemove before installation · 046 / 088

Service note · 088

088: dry winter and HD filter system

Green wire mesh for winter; black HD with dry felt prefilter for dry, dusty work.

Later reviewed guidance: 046 / 088: dry HD filter without inner foam

  • The 088 is introduced as a heavy-duty saw developed from the 084, not as evidence that all 084 parts interchange. Its new filter system uses peripheral sealing lips; tightening the carburetor-box cover mounting screw clamps cover, element and filter base together.
  • The printed tool-free conversion is: remove the carburetor-box cover, change the filter element, and refit the cover. Clean when engine power noticeably drops; no fixed cleaning interval is specified.
  • The green wire-mesh winter filter is for winter operation. The black HD filter is for dry and very dusty conditions; its element (2) is protected from coarse dirt by dry felt prefilter (1). Both winter and HD filters must be used dry: do not impregnate with oil. In snow, replace the HD filter with the winter filter to reduce icing risk.
  • The compensator is described as maintaining fuel content as the filter becomes dirty, preventing an over-rich mixture and avoiding high-speed screw readjustment solely for filter contamination. This is not a diagnosis or a claim that a blocked filter never needs cleaning.
  • TI 07/1991 is referenced for the detailed compensator description but is not in the retained bulletin inventory; that detail remains a source dependency. No filter ordering numbers or 084 oil-filter conversion are inferred from these numberless drawings.

Source: TI 35/1996, p. 1 · TI 35/1996, p. 2 · TI 35/1996, p. 3 — Cover and sections1.1–1.2, including both filter drawings.

No additional parts-table entry added.

Service note · 088

088: engine, intake flange and cooling changes

A wider big-end bearing and lightweight flywheel distinguish the launch construction from 084.

  • The illustrated new intake flange (1) is described as improving airflow and torque. The crankshaft has a wider big-end bearing, with strengthened crankshaft and crankcase. No dimensions, ordering numbers or cross-model swap permission are supplied.
  • The cylinder has increased cooling surface area. A lightweight flywheel with polymer fan and small high-power magnets is described as increasing cooling air volume by approximately 20%, improving acceleration from idle to maximum speed, handling and control, and reducing main-bearing load.
  • These are historical manufacturer design claims relative to 084, not measurements reproduced here. No introduction serial, 084 retrofit or later MS880 applicability is inferred.

Source: TI 35/1996, p. 1 · TI 35/1996, p. 3 — Cover and sections1.3–1.5.

No additional parts-table entry added.

Service note · 088

088: replacement filter cover loses carburetor-adjustment symbol

1124 141 0510 keeps its number; only the modified version is factory supplied.

in progress — Introduction in progress; no numeric machine-number boundary supplied.

  • Section 2 says REPLACEMENT filter cover 1124 141 0510 will in future be supplied WITHOUT THE CARBURETOR ADJUSTMENT SYMBOL. Summary item 8 repeats the SAME number in original and new columns.
  • Remark 3 applies to this cover: ONLY THE MODIFIED VERSION IS AVAILABLE FROM FACTORY. This is different from old-carburetor unavailability and old-component spare availability. No separate decal number, instruction to remove symbols from existing covers, or cover shape modification is supplied.
  • The exact 088 air-filter sheet contains the cover number and provides the assembly association. It does not transfer the HT-12A setup to the later HT-12E carburetor also drawn on that sheet.
  • Introduction is IN PROGRESS; no numeric serial cutoff is printed. Historical 088 / TI40/1997 evidence only, not a current stock claim or verified physical interchange. No hardware operation was performed.

Source: TI 40/1997, p. 4 · TI 40/1997, p. 5 — Section2 and summary item8/remark3.

Part numbers (1)
  • 1124 141 0510 — Filter cover; summary item 8Unchanged number; modified version only from factory · 088 TI40/1997 configuration, subject to the conditions in this note

Service note · 088

088: 7501 grommet accompanies HT-12A; original 7500 stays a spare

Matching grommet is necessary for the new carburetor and included in its package.

in progress — Introduction in progress; no numeric machine-number boundary supplied.

  • Sections 1 and 3 replace grommet 1124 123 7500 with 1124 123 7501 in connection with the new HT-12A. The new grommet WILL BE SUPPLIED WITH CARBURETOR 1124 120 0650 to ensure interchangeability with older machines. Do not infer that the grommet alone updates an old HT-11D.
  • Summary item 7 places 7501 INSIDE the HT-12A package. Separate original grommet item 9 carries remark 2: REMAINS AVAILABLE AS SPARE. Its dash in the new column is not cancellation of old-machine spare support.
  • The TI supplies no grommet color, hole count, cutting procedure or dimensions. The exact 088 air-filter sheet contains both numbers; do not import the gray one-hole 026 grommet description from TI39/1997.
  • Introduction is IN PROGRESS; no numeric serial cutoff is printed. Historical 088 / TI40/1997 evidence only, not a current stock claim or verified physical interchange. No hardware operation was performed.

Source: TI 40/1997, p. 1 · TI 40/1997, p. 4 · TI 40/1997, p. 5 — Sections1/3 and summary items7/9, package inclusion and remark2.

Part numbers (2)
  • 1124 123 7500 — Original grommet; summary item 9Remains available as spare · 088 TI40/1997 configuration, subject to the conditions in this note
  • 1124 123 7501 — Modified grommet; summary item 7Included with replacement HT-12A · 088 TI40/1997 configuration, subject to the conditions in this note

Wrong number or missing part for the 088? Report a correction →