Stihl 1128 · Section F · 6 of 17 · 39 parts
Ignition system
Fits 044.
Historical fitment & changes (9) — includes parts and conditions not shown on this drawing.
Parts (39)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1128 400 1214 | Flywheel Fitment / change note → | 1 |
| 2 | 1128 400 1215 | Flywheel Fitment / change note → | 1 |
| 3 | 1118 400 4000 NLA | Generator | 1 |
| 5 | 9041 216 0540 NLA | Pan head screw M3.5x12 | 3 |
| 6 | 0000 955 0802 | Collar nut M8x1 | 1 |
| 7 | 0000 400 1300 | Ignition module Fitment / change note → → replaced by 1122 400 1311, 0000 400 1305, 0000 400 1305 TI 51/1994 | 1 |
| 8 | not sold separately | Ignition lead 150 mm not available as a separate item | 1 |
| 9 | 0000 448 1250 | Lead retainer | 1 |
| 10 | 1122 442 0400 | Insulating hose 100 mm / 4'' | 1 |
| 11 | 1128 440 3002 | Wiring harness | 1 |
| 12 | 0751 030 8957 | Terminal socket 4.8-1/0.8 no longer available from factory | 1 |
| 13 | 0751 030 8955 | Terminal socket 4.8-1/0.4 no longer available from factory | 1 |
| 14 | 0751 030 8407 | Terminal socket 2.8-1/0.4 no longer available from factory | 1 |
| 15 | 0751 030 8969 | Terminal socket A5-1.5 no longer available from factory | 1 |
| 16 | 0000 989 0814 | Grommet | 1 |
| 17 | 1128 440 3003 | Wiring harness | 1 |
| 18 | 1118 431 6700 NLA | Terminal socket no longer available from factory | 1 |
| 19 | 1118 431 6600 NLA | Terminal pin no longer available from factory | 2 |
| 20 | 0751 030 8963 | Terminal socket 12-1 no longer available from factory | 1 |
| 21 | 1121 442 0402 NLA | Insulating hose 35 mm / 1.4'' Fitment / change note → | 1 |
| 22 | 1128 440 3012 | Wiring harness Fitment / change note → | 1 |
| 23 | 0751 030 8968 NLA | Terminal socket 5-2.5 no longer available from factory | 1 |
| 24 | not sold separately | Terminal socket not available as a separate item | 1 |
| 25 | 0000 989 0812 | Grommet | 1 |
| 26 | 1121 442 0402 NLA | Insulating hose 35 mm / 1.4'' Fitment / change note → | 3 |
| 27 | 9022 341 1019 | Spline screw IS-M5x20 | 2 |
| 28 | 1128 084 1400 | Cover | 1 |
| 29 | 1128 405 1000 | Spark plug boot | 1 |
| 30 | 0000 998 0604 | Torsion spring | 1 |
| 31 | 1125 084 8900 | Grommet | 1 |
| 32 | 0000 989 1010 | Grommet | 1 |
| 33 | 1121 405 1900 NLA | Support | 1 |
| 49 | 9291 021 0120 | Washer 5.3 | 2 |
| 50 | 1128 440 3007 | Wiring harness Fitment / change note → | 1 |
| 51 | 0751 030 8953 NLA | Terminal socket 4.8-1 no longer available from factory | 1 |
| 52 | 0751 030 8470 | Grommet no longer available from factory | 1 |
| 53 | 1121 442 0402 NLA | Insulating hose 35 mm / 1.4'' Fitment / change note → | 2 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 0000 405 0600 NLA | Ignition lead 1 m not illustratedoption | 1 |
| — | 0000 930 2251 | Ignition lead 10 m not illustratedoption | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Conditional replacement · 044
044 arctic: match flywheel and handle heaters
The 1995 combined carburetor/handle-heating system uses flywheel 1128 400 1213 and higher-resistance handle heaters. The old and new heating configurations must not be treated as interchangeable.
Later reviewed guidance: 044: stiffened handle needs matching version and screws
X 30 991 112 — Combined carburetor and handle heating on the 044 arctic version described by this TI.
- Applies to the heating-equipped 044 variants described by TI 07/1995, not all 044s. Combined carburetor and handle heating starts from X 30 991 112.
- Original flywheel 1128 400 1205 must not be fitted to the combined carburetor/handle-heating configuration.
- When fitting new flywheel 1128 400 1213 to a saw up to X 30 991 111, the TI requires rear heater 1128 434 5000 and front handle 1128 790 1707. Old handle 1128 790 1705 is restricted to saws up to that earlier limit.
- The TI warns of heater burnout with prolonged full-throttle operation using the old handle and new flywheel. This note preserves the matching requirement, not a timed operating allowance.
- The front-heater table prints 6.3–7.7 W under a resistance heading. That unit is unresolved; this note does not turn it into a verified resistance specification.
- The original page 1 drawing labels 11 mm (1/2 inch) at the old magnet and 6 mm (1/4 inch) at the new magnet. These are the printed identification dimensions, not a specified ignition air gap; the metric/inch pairs are not exact conversions. The source claims up to 45% more generator output depending on RPM, not a measured output or guaranteed value at all speeds.
- At +25°C (77°F), the table gives original rear-heater resistance 0.225–0.275Ω and new rear heater 0.9–1.1Ω; original front heater 1.44–1.76Ω. The new front entry remains printed 6.3–7.7 W under a resistance heading, not silently corrected to ohms. No pass/fail electrical limit is inferred for that disputed cell.
- New rear heater 1128 434 5000 has thinner, wavy printed conductors compared with 1125 434 5000; the service note requires it to be bonded in the rear handle for the early-saw/new-flywheel combination. The original illustration identifies the two patterns.
- The original warning says not to run the old front handle/new flywheel combination at full throttle for more than about 4 minutes because the heater would burn out. This records the historical warning, not an approved four-minute operating or bench-test allowance; fit the required matching heaters.
- Summary availability: original flywheel is supplied only while existing factory stocks last; original front handle and rear heater remain available for older machines. This does not cancel the old-flywheel prohibition on combined heating or the old-handle serial restriction.
- Scope is the 044 Arctic combined carburetor/handle-heating configuration in TI 07/1995, dated January 2, 1995. The electrical data differ from earlier handle-only 044W saws; no automatic MS440 or other shared-part applicability. Availability remarks are historical, not current stock.
Source: TI 7/1995, p. 1 · TI 7/1995, p. 3 · TI 7/1995, p. 5 — Sections1,3–4; complete handle resistance table, flywheel identification drawing, service notes and summary.
Part numbers (6)
- 1128 400 1205 — FlywheelOriginal / restricted · Older 044 heating configuration; excluded from combined heating
- 1128 400 1213 — FlywheelConditional replacement · 044 heating system; match front and rear heaters
- 1128 790 1705 — Heated front handleOriginal / restricted · 044 up to X 30 991 111 only
- 1128 790 1707 — Heated front handleRequired companion · Higher-resistance handle for new flywheel configuration
- 1125 434 5000 — Rear handle heating elementOriginal equipment · Older 044 heating configuration
- 1128 434 5000 — Rear handle heating elementRequired companion · New 044 heating configuration
Conditional replacement · 044
044 arctic: thermostat moved to the heater
The arctic configuration changed to the standard HD-10 B carburetor together with a new heating element carrying the thermostat and an additional gasket.
X 37 180 486 — Introduction of the combined carburetor/heater arrangement for the specified arctic variant.
- Applies to 044 arctic, not a blanket carburetor substitution for all 044s.
- New heating element 1128 430 6000 and gasket 1128 129 1100 accompany the new carburetor arrangement. The gasket is fitted between carburetor and heating element.
- The older 1128 434 5101 heater and 1128 430 0501 thermostat remained available for older machines in this TI; the new thermostat is not listed as a separate service item.
- X 37 180 486 is the introduction of this combined arctic configuration, not a model-identification range or permission for an unmatched retrofit.
- The thermostatic switch moves from the carburetor end cover to the heating element; the respective standard carburetor is then used with the new element. Gasket 1128 129 1100 fits between carburetor and element to improve heat distribution according to the source, not a reproduced temperature measurement.
- The original carburetor 1128 120 0620 includes the thermostatic switch; new heating element 1128 430 6000 includes the new switch. The new-switch table entry is not an orderable number: it is unavailable separately. Original carburetor 1128 120 0620 is no longer factory-supplied; standard carburetor 1128 120 0619 is already in inventory. Retention of older heater/switch spares is not permission for an unmatched retrofit or a current-stock claim.
Source: TI 9/1997, p. 3 · TI 9/1997, p. 4 — Complete section3:model-specific arctic carburetor/heater rows,gasket drawing,serial and all supply remarks.
Part numbers (6)
- 1128 120 0620 — HD-11 A carburetorOriginal arctic configuration · 044 arctic with thermostat on carburetor
- 1128 120 0619 — HD-10 B carburetorNew arctic configuration · 044 arctic only with matched new heating arrangement
- 1128 434 5101 — Heating elementOriginal equipment · 044 older arctic heating arrangement
- 1128 430 0501 — Thermostatic switchOriginal service part · 044 older arctic arrangement; not the new integrated thermostat
- 1128 430 6000 — Heating element with thermostatRequired companion · 044 revised arctic heating arrangement
- 1128 129 1100 — GasketRequired companion · Between carburetor and new heating element
Historical fitment · 044 / 046
Generator connector: insulating tube replaces housings
TI 09/1997 replaces the generator connector pin and socket housings with insulating tube 1121 442 0402.
- Applies at the wiring-harness/generator plug connection on the heating-equipped configurations; not to every connector on either saw.
- The tube is the replacement insulation, not a replacement electrical contact. The TI gives no numeric introduction cutoff.
- The summary specifies tube dimensions 3.3 × 0.9 × 35 for 1121 442 0402 without an explicit unit or axis convention on this page; do not invent either from the three values alone. Both original pin housing 1128 431 8400 and socket housing 1128 431 8700 remain factory-supplied only while stocks last.
- This connection change is in progress; the preceding arctic-heater serialX 37 180 486 is not its cutoff. The footer identifies last TIs 044:38/1996 and 046:05/1997. The 09/1997 issue bears a 1996 copyright imprint; the imprint is not silently changed or treated as the modification date.
Source: TI 9/1997, p. 4 — Complete section4:connection prose,all three table rows,dimensions,introduction/supply remarks and footer.
Part numbers (3)
- 1128 431 8400 — Pin housingOriginal insulation · 044 / 046 generator plug connection
- 1128 431 8700 — Socket housingOriginal insulation · 044 / 046 generator plug connection
- 1121 442 0402 — Insulating tubeReplacement insulation · 044 / 046 wiring-harness/generator connection
Conditional replacement · 044
044: revised flywheels keep standard and heated variants separate
The revised flywheels are interchangeable with their corresponding original versions, not across heating configurations.
- Standard 044: 1128 400 1200 → 1128 400 1214. Heating-equipped 044: 1128 400 1213 → 1128 400 1215.
- The interchangeability statement applies within these table rows; it does not make a standard flywheel suitable for the heating system.
- The source schedules flywheel introduction for the beginning of 1998; no numeric serial cutoff is supplied. Earlier combined-heating matching requirements remain separate.
- The blade count is reduced from 28 to 21 and the contour optimized to increase cooling-air throughput. Rare-earth magnet material permits smaller magnets and counterweight, larger effective blade area and reduced flywheel weight. These are source claims, not measured project performance.
- Drawing132TI020 distinguishes original (1) and new (2). Full interchangeability is stated within each standard/heated version. Original flywheel versions remain factory-supplied only while stocks last.
Source: TI 47/1997, p. 8 · TI 47/1997, p. 9 — Sections 5.1–5.3: flywheel service note and variant table; full section, drawing and summary context reviewed in batch26.
Part numbers (4)
- 1128 400 1200 — Standard flywheelOriginal version · 044 without heating
- 1128 400 1214 — Standard flywheelRevised version · 044 without heating
- 1128 400 1213 — Heating flywheelOriginal version · 044 heating-equipped
- 1128 400 1215 — Heating flywheelRevised version · 044 heating-equipped
Historical fitment · 044
044: ignition module revision
Historical TI 47/1997 recommendation only: later TI 22/1998 splits the universal-module rule by model. Read the linked later guidance.
Later reviewed guidance: 044: later ignition guidance replaces the universal-module rule
- Later TI 22/1998 revises this recommendation. Do not use this 1997 record alone to select a replacement module.
- 044: 0000 400 1300 → 0000 400 1305.
- The new module has a two-arm yoke without timing adjustment. Do not carry the old 046 three-arm timing-adjustment feature over to it.
- The word universal in this bulletin is not proof of compatibility with unlisted models. Introduction was in progress; no numeric cutoff is supplied.
- The original 044 module already has a two-arm yoke; the 046 original has three arms and timing adjustment.
- Original module remains factory-supplied only while stocks last. The cover expressly excludes section5.2 from the modifications described as achieving EPA compliance; replacement alone is not an EPA-conversion claim. Later TI22/1998 guidance remains attached and takes precedence for selection.
Source: TI 47/1997, p. 1 · TI 47/1997, p. 9 — Sections 5.2–5.3: ignition module and summary; full section, drawing and summary context reviewed in batch26.
Part numbers (2)
- 0000 400 1300 — Ignition moduleOriginal version · 044
- 0000 400 1305 — Two-arm ignition moduleNew version · 044; no timing adjustment
Conditional replacement · 044
044: later ignition guidance replaces the universal-module rule
TI 22/1998 splits the former 1305 replacement by model after field reliability problems; this is later guidance than TI 47/1997.
- The later reviewed replacement for 044 is 0000 400 1300. Do not automatically cross-reference 0000 400 1305 to one number for every model.
- 044 belongs to the aluminium-flywheel group using the optimized 0000 400 1300. The reactivated number does not distinguish every historical construction revision.
- The separate 064 and 066 previous-module/serial restrictions are not 044 or 046 cutoffs. This record does not approve those other models.
- Introduction is in progress; no numeric 044/046 cutoff is stated. This is dated historical service guidance, not proof of the latest available module.
- The reactivated 0000 400 1300 number identifies the optimized aluminium-flywheel module here. The modified version has an integrated 400 mm (15 3/4 inch) ignition lead, no separate ignition lead and no short-circuit wire. The reused number alone does not distinguish all older constructions.
- TI22/1998 reports isolated reliability problems with the former universal module on aluminium-flywheel machines. Different timing requirements led to two optimized modules; this is historical manufacturer field-test guidance, not a project hardware test.
- Order only 0000 400 1300 or 1122 400 1314 according to the named model and restrictions. There is no automatic one-number replacement for 0000 400 1305.
- The 02.98 microfiche/CD-ROM issue documents the future part numbers. Both summary rows say the original 0000 400 1305 is no longer available from the factory; that does not revoke the expressly permitted use of existing stocks on eligible 046/066 machines.
- Introduction is in progress, without a new production cutoff. Factory availability is a 1998 statement, not current stock or proof of physical interchange.
Source: TI 22/1998, p. 1 · TI 22/1998, p. 2 — Sections 1–6: history, split, service note and ordering.
Part numbers (2)
- 0000 400 1305 — Former universal ignition moduleEarlier recommendation · 044; read later model-specific service guidance
- 0000 400 1300 — Model-specific ignition moduleLater reviewed replacement · 044 under TI 22/1998
Conditional replacement · 044
044 ignition module: two captive-washer screws replace loose washers
Two IS-M5x20 screws with captive washers replace the original screw/washer pairs; the original washer number is malformed in the source and is not silently corrected.
- Original spline screws 9022 371 1020 and separate A5.3 washers (two each) are replaced by two captive-washer IS-M5x20 screws 9022 371 1022.
- The washer row is printed exactly “991 021 0120” in both the scan and text, not a four-digit first group. It is retained here as unresolved source text, not normalized to an invented orderable part number.
- Introduction is in progress with no numeric serial cutoff. Original screw and washer remain as spares for other models, not proof of universal substitution. No mounting torque is stated in this section.
- TI16/1994 is dated March 21, 1994. Historical availability and production statements are not present inventory or verified physical interchange; no successor-model applicability is inferred.
Source: TI 16/1994, p. 5 — Section3, complete mounting summary and printed washer anomaly.
Part numbers (2)
- 9022 371 1020 — Original IS-M5x20 spline screwHistorical version · 044 configuration described in this record
- 9022 371 1022 — IS-M5x20 screw with captive washerNew, two required · 044 configuration described in this record
Conditional replacement · 044
044 Arctic: combined-heating harness and wire routing
Harness 1128 440 3012 adds handle-heating wires. The original circuit and routing drawings are essential to keeping the generator wire clear of the flywheel.
X 30 991 112 — Combined carburetor and handle heating on the 044 Arctic version described by TI07/1995; not a universal 044 model boundary.
- Original harness 1128 440 3007 → 1128 440 3012 adds handle-heating wires; the old harness remains available for older machines. This does not describe a generic harness swap independent of heater/flywheel configuration.
- Page 4 circuit drawing 132TI004 has generator 1 and round connector 2 feeding two parallel branches: rear heater 3 then front heater 4 and heater switch 5 in series; carburetor heater 6 and thermostatic switch 7 in the other branch. The diagram contains no connector pin numbers or wire-color map; labels 1–7 are component keys, not pinouts. The carb heater is not shown downstream of the handle-heater switch.
- After ignition-module-area work, push retainer 1 into the crankcase recess, turn round connector 2 as shown in drawing 132TI005, then install the module. Generator wire must lie in crankcase slot 3 well clear of the flywheel. The linked original drawing supplies the orientation, not an inferred universal connector angle.
- At the thermostatic switch, do not bend or kink the plug connector during installation/removal because the connections may break (drawing 132TI006).
- Beside the carburetor, loop the wires, push through tube 1121 442 0400 and position as illustrated in 132TI007. The 044 catalog sheets also list insulating hose 1121 442 0402; this bulletin does not establish 0400 → 0402 equivalence or substitution. Only 0400 is the number admitted from this source.
- Scope is the 044 Arctic combined carburetor/handle-heating configuration in TI 07/1995, dated January 2, 1995. The electrical data differ from earlier handle-only 044W saws; no automatic MS440 or other shared-part applicability. Availability remarks are historical, not current stock.
Source: TI 7/1995, p. 1 · TI 7/1995, p. 3 · TI 7/1995, p. 4 · TI 7/1995, p. 5 — Sections3,5–6, all four circuit/routing diagrams and harness summary.
Part numbers (3)
- 1128 440 3007 — Original wiring harnessOlder heating configuration · 044 Arctic combined heating; not all 044 variants
- 1128 440 3012 — Wiring harness with handle-heater wiresNew combined-heating configuration · 044 Arctic combined heating; not all 044 variants
- 1121 442 0400 — Wire routing tubeTI routing reference; no 0402 alias · 044 Arctic combined heating; not all 044 variants
Historical fitment · 044
044: series 1128 replacement ignition assignment
0000 400 1300 and the listed flywheel pairings for series 1128; 150 mm ignition lead.
- Standard: 0000 400 1300 with flywheel 1128 400 1200.
- Heating: 0000 400 1300 with flywheel 1128 400 1213.
- Printed ignition-lead length: 150 mm (6 in). Preserve the printed metric and inch values; no rounding correction is inferred.
- TI01/1999 lists replacement combinations for the then-current machines, not every earlier configuration. Older machines are referred to Spare Parts for Previous Models in their own illustrated parts lists; no serial cutoff is supplied here.
- Use only the listed ignition-module/flywheel combinations. The source warns that incorrect combinations can cause excessive RPM or running in reverse; sharing a module number does not make all flywheels interchangeable.
- Universal replacement modules may differ from production modules in maker, shape and part number. The source describes installation/function compatibility within its assignments, not universal compatibility or a project hardware test.
- Some replacement modules require shortening the ignition lead and/or short-circuit wire and crimping a different short-circuit connector. The table gives ignition-lead lengths only; it supplies neither a short-circuit-wire length nor a connector part number. Do not infer that every row needs modification.
- Only the named models and printed series are covered. A shared IPL sheet does not extend this assignment to unnamed models or modern MS equivalents. This 1999 USA bulletin is historical guidance, not current availability.
Source: TI 1/1999, p. 1 · TI 1/1999, p. 2 — 1.1 general restrictions and 1.2.1 chainsaw assignments.
Part numbers (3)
- 0000 400 1300 — Replacement ignition moduleAssigned replacement · 044, series 1128, only with the listed flywheel branch
- 1128 400 1200 — Standard flywheelRequired pairing · 044, series 1128; standard only
- 1128 400 1213 — Heating flywheelRequired pairing · 044, series 1128; heating only
Wrong number or missing part for the 044? Report a correction →