Stihl 1128 · Section P · 15 of 17 · 29 parts
Handlebar, Heating element
Fits 044.
Historical fitment & changes (4) — includes parts and conditions not shown on this drawing.
Parts (29)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1128 790 1750 | Handlebar with hose Fitment / change note → | 1 |
| 2 | not sold separately | Handle hose 460 mm / 18 1/8'' | 1 |
| 3 | 9074 478 4475 | Pan head self-tapping screw IS-P6x21.5 Fitment / change note → | 4 |
| 4 | 1128 790 3600 | Wrap around handlebar | 1 |
| 5 | not sold separately | Handle hose 225 mm / 8 7/8'' not available as a separate item | 1 |
| 6 | not sold separately | Handle hose 290 mm / 13 3/4'' not available as a separate item | 1 |
| 7 | 1128 791 5500 | Elbow connector → replaced by 1128 791 5501 TI 15/2007 | 1 |
| 8 | 9074 478 4675 | Pan head self-tapping screw IS-P6x32.5 | 2 |
| 9 | 9022 371 1020 | Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 | 1 |
| 10 | 1128 434 5000 NLA | Heating element Fitment / change note → | 1 |
| 11 | 1118 431 6700 NLA | Terminal socket no longer available from factory | 2 |
| 12 | 1118 431 6600 NLA | Terminal pin no longer available from factory | 1 |
| 13 | 1121 791 9000 NLA | Clamp | 1 |
| 14 | 1121 442 0402 NLA | Insulating hose 35 mm / 1.4'' | 2 |
| 15 | 0000 958 1511 | Washer | 1 |
| 16 | 1128 430 0200 | Switch | 1 |
| 17 | 1128 432 2200 | Hexagon nut | 1 |
| 18 | 1110 432 9200 | Grommet | 1 |
| 19 | not sold separately | Insulating hose not available as a separate item | 1 |
| 20 | 0000 442 7000 NLA | Contact sleeve no longer available from factory | 1 |
| 21 | 9307 021 0120 | Washer 5.3 | 1 |
| 22 | 1128 790 1752 | Handlebar Fitment / change note → | 1 |
| 39 | 9074 478 4435 | Pan head self-tapping screw IS-P6x19 Fitment / change note → | 4 |
| 40 | 1125 434 5000 NLA | Heating element Fitment / change note → | 1 |
| 41 | 1121 430 0200 | Heating switch | 1 |
| 42 | 0000 961 1406 NLA | Ring | 1 |
| 43 | 0000 958 1406 NLA | Washer | 1 |
| 44 | 1118 432 2200 NLA | Hexagon nut M12 | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 0000 791 2009 | Handle hose Ø 19 mm x 5 m / 3/4x197'' not illustratedoption | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Conditional replacement · 044
044 arctic: match flywheel and handle heaters
The 1995 combined carburetor/handle-heating system uses flywheel 1128 400 1213 and higher-resistance handle heaters. The old and new heating configurations must not be treated as interchangeable.
Later reviewed guidance: 044: stiffened handle needs matching version and screws
X 30 991 112 — Combined carburetor and handle heating on the 044 arctic version described by this TI.
- Applies to the heating-equipped 044 variants described by TI 07/1995, not all 044s. Combined carburetor and handle heating starts from X 30 991 112.
- Original flywheel 1128 400 1205 must not be fitted to the combined carburetor/handle-heating configuration.
- When fitting new flywheel 1128 400 1213 to a saw up to X 30 991 111, the TI requires rear heater 1128 434 5000 and front handle 1128 790 1707. Old handle 1128 790 1705 is restricted to saws up to that earlier limit.
- The TI warns of heater burnout with prolonged full-throttle operation using the old handle and new flywheel. This note preserves the matching requirement, not a timed operating allowance.
- The front-heater table prints 6.3–7.7 W under a resistance heading. That unit is unresolved; this note does not turn it into a verified resistance specification.
- The original page 1 drawing labels 11 mm (1/2 inch) at the old magnet and 6 mm (1/4 inch) at the new magnet. These are the printed identification dimensions, not a specified ignition air gap; the metric/inch pairs are not exact conversions. The source claims up to 45% more generator output depending on RPM, not a measured output or guaranteed value at all speeds.
- At +25°C (77°F), the table gives original rear-heater resistance 0.225–0.275Ω and new rear heater 0.9–1.1Ω; original front heater 1.44–1.76Ω. The new front entry remains printed 6.3–7.7 W under a resistance heading, not silently corrected to ohms. No pass/fail electrical limit is inferred for that disputed cell.
- New rear heater 1128 434 5000 has thinner, wavy printed conductors compared with 1125 434 5000; the service note requires it to be bonded in the rear handle for the early-saw/new-flywheel combination. The original illustration identifies the two patterns.
- The original warning says not to run the old front handle/new flywheel combination at full throttle for more than about 4 minutes because the heater would burn out. This records the historical warning, not an approved four-minute operating or bench-test allowance; fit the required matching heaters.
- Summary availability: original flywheel is supplied only while existing factory stocks last; original front handle and rear heater remain available for older machines. This does not cancel the old-flywheel prohibition on combined heating or the old-handle serial restriction.
- Scope is the 044 Arctic combined carburetor/handle-heating configuration in TI 07/1995, dated January 2, 1995. The electrical data differ from earlier handle-only 044W saws; no automatic MS440 or other shared-part applicability. Availability remarks are historical, not current stock.
Source: TI 7/1995, p. 1 · TI 7/1995, p. 3 · TI 7/1995, p. 5 — Sections1,3–4; complete handle resistance table, flywheel identification drawing, service notes and summary.
Part numbers (6)
- 1128 400 1205 — FlywheelOriginal / restricted · Older 044 heating configuration; excluded from combined heating
- 1128 400 1213 — FlywheelConditional replacement · 044 heating system; match front and rear heaters
- 1128 790 1705 — Heated front handleOriginal / restricted · 044 up to X 30 991 111 only
- 1128 790 1707 — Heated front handleRequired companion · Higher-resistance handle for new flywheel configuration
- 1125 434 5000 — Rear handle heating elementOriginal equipment · Older 044 heating configuration
- 1128 434 5000 — Rear handle heating elementRequired companion · New 044 heating configuration
Conditional replacement · 044
044: stiffened handle needs matching version and screws
TI 11/2000 changes front handles and mounting screw length; heated variants must retain the correct electrical pairing.
- Stiffened replacement handles require the longer IS-P6×21.5 screws 9074 478 4475 in place of IS-P6×19 screws 9074 478 4435. The TI describes historical supply with handles, not guaranteed current contents.
- 044 non-heated: front handle 1128 790 1700 → 1128 790 1750.
- 044 heated, original low-resistance system: front handle 1128 790 1705 → 1128 790 1751.
- 044 heated, later higher-resistance system: front handle 1128 790 1707 → 1128 790 1752.
- For heated 044 at 25°C: rear element 0.225–0.275 ohm pairs with front handle 1128 790 1751 (1.44–1.76 ohm); rear 0.9–1.1 ohm pairs with 1128 790 1752 (6.3–7.7 ohm). Identify the installed rear element, not just the handle appearance.
- The 1751 row is marked for machines up to X 30 991 111. This is a heating-system applicability limit, not the introduction serial for all stiffened handles.
- The stiffener adds thickness: drawing 145TI038 KN labels A without stiffener and B with stiffener. The longer screws are supplied with replacement handles according to page 4. Summary items 6 and 7 each specify two screws (2x); do not retain the shorter screws for the stiffened arrangement.
- Each front-handle summary row literally says including items 6, 7, spanning the previous IS-P6 × 19 and new IS-P6 × 21.5 screw rows. Page 4 specifies replacement supply with the longer screws; the summary is not evidence that both lengths must be installed or are both supplied with a current replacement.
- The modification is in progress, with no numeric stiffened-handle introduction serial. Previous short screw 9074 478 4435 has no new number in its own row and remains available for other, unnamed models (remark 3); the new long screw is separately item 7. This does not retain the short screw for a stiffened handle.
- The two illustrated rear-heater patterns are identification evidence: combination 1 (145TI035 KN) has broader, straighter conductors; combination 2 (145TI036 KN) has finer, serpentine conductors. Section 2.1 says the two replacement heated handles differ only in heating-element resistance; identify the installed rear element or measure resistance at 25°C (77°F). No rear-element part number is supplied by this table.
- The new table explicitly labels the 6.3–7.7 front-heater range Ohm. This is independent TI11/2000 evidence for replacement handle 1128 790 1752, not a silent correction of the unresolved W entry in TI07/1995. The earlier flywheel/heater matching restriction remains; a serial alone does not establish the installed electrical configuration.
- Summary remark 1 ends factory supply of previous 044 non-heated 1128 790 1700 and later heated 1128 790 1707. The early heated 1128 790 1705 → 1128 790 1751 row instead carries remark 2, for machines through X 30 991 111 (see service note). Do not apply remark 1 to that early row or reinterpret its serial as the new-handle introduction.
- The parenthetical see service note is retained without assigning an unidentified external document to it. The available section 2.1 table supplies replacement selection, but does not reproduce the earlier full heating-system diagnostic procedure. Last-TI references 35/1999 and 28/1999 are bibliography, not supersession.
Source: TI 11/2000, p. 4 · TI 11/2000, p. 5 — Sections 2–2.2: front handle assignment and summary; complete installation/identification drawings and supply remarks reviewed.
Part numbers (8)
- 1128 790 1700 — Front handleOriginal equipment · 044 non-heated
- 1128 790 1750 — Stiffened front handleConditional replacement · 044 non-heated; longer screws required
- 1128 790 1705 — Front handleOriginal equipment · 044 heated, original low-resistance system
- 1128 790 1751 — Stiffened front handleConditional replacement · 044 heated, original low-resistance system; longer screws required
- 1128 790 1707 — Front handleOriginal equipment · 044 heated, later higher-resistance system
- 1128 790 1752 — Stiffened front handleConditional replacement · 044 heated, later higher-resistance system; longer screws required
- 9074 478 4435 — IS-P6×19 screwOriginal equipment · 044 original handle
- 9074 478 4475 — IS-P6×21.5 screwRequired companion · 044 stiffened handle
Conditional replacement · 044
044 Arctic: combined-heating harness and wire routing
Harness 1128 440 3012 adds handle-heating wires. The original circuit and routing drawings are essential to keeping the generator wire clear of the flywheel.
X 30 991 112 — Combined carburetor and handle heating on the 044 Arctic version described by TI07/1995; not a universal 044 model boundary.
- Original harness 1128 440 3007 → 1128 440 3012 adds handle-heating wires; the old harness remains available for older machines. This does not describe a generic harness swap independent of heater/flywheel configuration.
- Page 4 circuit drawing 132TI004 has generator 1 and round connector 2 feeding two parallel branches: rear heater 3 then front heater 4 and heater switch 5 in series; carburetor heater 6 and thermostatic switch 7 in the other branch. The diagram contains no connector pin numbers or wire-color map; labels 1–7 are component keys, not pinouts. The carb heater is not shown downstream of the handle-heater switch.
- After ignition-module-area work, push retainer 1 into the crankcase recess, turn round connector 2 as shown in drawing 132TI005, then install the module. Generator wire must lie in crankcase slot 3 well clear of the flywheel. The linked original drawing supplies the orientation, not an inferred universal connector angle.
- At the thermostatic switch, do not bend or kink the plug connector during installation/removal because the connections may break (drawing 132TI006).
- Beside the carburetor, loop the wires, push through tube 1121 442 0400 and position as illustrated in 132TI007. The 044 catalog sheets also list insulating hose 1121 442 0402; this bulletin does not establish 0400 → 0402 equivalence or substitution. Only 0400 is the number admitted from this source.
- Scope is the 044 Arctic combined carburetor/handle-heating configuration in TI 07/1995, dated January 2, 1995. The electrical data differ from earlier handle-only 044W saws; no automatic MS440 or other shared-part applicability. Availability remarks are historical, not current stock.
Source: TI 7/1995, p. 1 · TI 7/1995, p. 3 · TI 7/1995, p. 4 · TI 7/1995, p. 5 — Sections3,5–6, all four circuit/routing diagrams and harness summary.
Part numbers (3)
- 1128 440 3007 — Original wiring harnessOlder heating configuration · 044 Arctic combined heating; not all 044 variants
- 1128 440 3012 — Wiring harness with handle-heater wiresNew combined-heating configuration · 044 Arctic combined heating; not all 044 variants
- 1121 442 0400 — Wire routing tubeTI routing reference; no 0402 alias · 044 Arctic combined heating; not all 044 variants
Historical fitment · 044
044 Arctic: diagnostic chart has a serial gate and separate source gaps
The carburetor-heating chart applies only above X30 991 111; older machines are referred to TI44/1992. Handle-heating test procedure is a separate 044 manual dependency.
X 30 991 112 — Combined carburetor and handle heating on the 044 Arctic version described by TI07/1995; not a universal 044 model boundary.
- Section 8.2 calls for checking carburetor heating for warm-up running problems, especially below freezing or at idle/part load; poor idling when warm is also an indication. These symptoms are not proof of a heating-system fault.
- The first chart decision is machine number HIGHER THAN X 30 991 111. NO goes to TI 44/1992, absent from the retained 690-TI corpus. Do not apply the later 8Ω test to the older configuration by default or turn the printed X prefix into a universal numeric model range.
- YES: check heater resistance at +25°C (77°F), approximately 8Ω. NO leads to fitting a new heating element, then the drawn return loop goes back to the resistance check. No tolerance band beyond approximately is supplied.
- After heater resistance passes, check switch CLOSING between +11 and +5°C (52…41°F), then OPENING between +5 and +11°C (41…52°F). A failed decision leads to replacing the switch; both replacement arrows return to the initial heater-resistance check, not directly to a healthy result.
- Only the three YES decisions lead to the chart label carburetor heating system in order. This is the source chart outcome for the stated checks, not an executed hardware test or proof of whole-saw health.
- Scope is the 044 Arctic combined carburetor/handle-heating configuration in TI 07/1995, dated January 2, 1995. The electrical data differ from earlier handle-only 044W saws; no automatic MS440 or other shared-part applicability. Availability remarks are historical, not current stock.
Source: TI 7/1995, p. 1 · TI 7/1995, p. 2 · TI 7/1995, p. 3 · TI 7/1995, p. 5 · TI 7/1995, p. 6 — Sections8.1–8.2 and complete page6 decision chart; component identity from sections2/7.
Part numbers (2)
- 1128 434 5101 — Carburetor heating elementReferenced by later-configuration chart · 044 Arctic combined heating; not all 044 variants
- 1128 430 0501 — Thermostatic switchReferenced by later-configuration chart · 044 Arctic combined heating; not all 044 variants
Wrong number or missing part for the 044? Report a correction →