Stihl 1128 · Section L · 11 of 17 · 57 parts
Carburetor HD-15C, HD-17C, HD-11A, HD-10B
Fits 044.
Historical fitment & changes (20) — includes parts and conditions not shown on this drawing.
Parts (57)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4116 121 5100 | Inlet needle Fitment / change note → | 1 |
| 2 | 4116 121 5000 | Inlet control lever Fitment / change note → | 1 |
| 3 | 1128 122 3002 | Spring Fitment / change note → | 1 |
| 4 | 1113 121 9200 | Spindle Fitment / change note → | 1 |
| 5 | 1114 122 7400 | Round head screw Fitment / change note → | 1 |
| 6 | 4117 122 9402 | Plug Fitment / change note → | 1 |
| 7 | 1128 121 5405 | Valve jet | 1 |
| 8 | 1128 121 5602 | Fixed jet 0.70 Fitment / change note → → replaced by 1128 121 5603 TI 47/1997 | 1 |
| 9 | 1128 121 5605 | Fixed jet 0.66 Fitment / change note → | 1 |
| 10 | 1128 129 0906 | Gasket Fitment / change note → | 1 |
| 11 | 4116 121 4700 | Metering diaphragm Fitment / change note → | 1 |
| 12 | 1128 121 0801 | End cover Fitment / change note → | 1 |
| 13 | 1121 122 7101 | Screw Fitment / change note → | 4 |
| 14 | 1114 121 7800 | Strainer Fitment / change note → | 1 |
| 15 | 4116 121 4800 | Pump diaphragm Fitment / change note → | 1 |
| 16 | 4116 129 0902 | Gasket Fitment / change note → | 1 |
| 17 | 1127 122 3205 | Torsion spring Fitment / change note → | 1 |
| 18 | 1127 120 7100 | Throttle shaft with lever Fitment / change note → | 1 |
| 19 | 1117 122 9000 | E-clip Fitment / change note → | 1 |
| 20 | 1128 121 3302 | Throttle shutter Fitment / change note → | 1 |
| 21 | 1115 122 7400 | Round head screw Fitment / change note → | 1 |
| 22 | 1127 122 3200 | Torsion spring Fitment / change note → | 1 |
| 23 | 1127 120 7200 | Choke shaft with lever Fitment / change note → | 1 |
| 24 | 1123 122 9000 | E-clip Fitment / change note → | 1 |
| 25 | 1122 121 2900 | Choke shutter Fitment / change note → | 1 |
| 26 | 1110 122 7400 | Round head screw Fitment / change note → | 1 |
| 27 | 1127 122 6200 | Idle speed adjustment screw Fitment / change note → | 1 |
| 28 | 1127 121 0800 | End cover Fitment / change note → | 1 |
| 29 | 1114 122 7100 | Screw Fitment / change note → | 1 |
| 30 | 1128 122 3003 | Spring Fitment / change note → | 2 |
| 31 | 1127 122 6701 | High speed adjustment screw Fitment / change note → | 1 |
| 32 | 1128 122 6807 | Low speed adjustment screw Fitment / change note → | 1 |
| 33 | 1128 122 6703 | High speed adjustment screw Fitment / change note → | 1 |
| 34 | 1128 122 6806 | Low speed adjustment screw Fitment / change note → | 1 |
| 35 | 4203 122 3600 | Sealing ring | 1 |
| 36 | 4203 121 2700 | Cap Fitment / change note → | 2 |
| 37 | 1128 129 1100 | Gasket Fitment / change note → | 1 |
| 38 | 1128 430 6002 | Heating element | 1 |
| 39 | 1118 431 6600 NLA | Terminal pin no longer available from factory | 1 |
| 40 | 1118 431 6700 NLA | Terminal socket Fitment / change note → no longer available from factory | 1 |
| 41 | 1124 121 9100 | Bushing | 1 |
| 42 | 1128 121 5605 | Fixed jet 0.66 Fitment / change note → option | 1 |
| 43 | 1122 121 5604 | Fixed jet 0.64 Fitment / change note → option | 1 |
| 50 | 1128 120 0619 | Carburetor HD-10B Fitment / change note → no longer available from factory | 1 |
| 51 | 1128 121 5403 | Valve jet Fitment / change note → | 1 |
| 52 | 1127 122 6700 | High speed adjustment screw Fitment / change note → | 1 |
| 53 | 4116 122 6800 | Low speed adjustment screw Fitment / change note → | 1 |
| 54 | 4116 122 3001 | Spring Fitment / change note → | 2 |
| 55 | 1128 120 0620 | Carburetor HD-11A Fitment / change note → no longer available from factory | 1 |
| 56 | 1128 121 0802 | End cover Fitment / change note → | 1 |
| 57 | 1128 122 7101 | Screw Fitment / change note → | 1 |
| 58 | 1128 122 9301 | Clip Fitment / change note → | 1 |
| 59 | 1128 121 8602 | Washer Fitment / change note → | 1 |
| 60 | 1128 121 8603 | Washer Fitment / change note → | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 1128 120 0625 | Carburetor HD-15C Fitment / change note → → replaced by 1128 120 0622 TI 39/2003 | 1 |
| — | 1128 120 0622 | Carburetor HD-17C Fitment / change note → | 1 |
| — | 1128 007 1066 | Set of carburetor parts Fitment / change note → | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Conditional replacement · 044
Zama to Walbro: check the compensator
TI 03/1996 replaces C3M-S5G 1128 120 0617 with HD-10 A 1128 120 0619 on the 044. The later IPL uses the same number for HD-10B; this record preserves the bulletin’s earlier designation.
- When replacing a carburetor without a compensator connection on a saw up to X 026 452 476, conversion to a compensator is required. TI 03/1996 refers to TI 54/1992, “Air filter”, for the conversion.
- That serial is a retrofit-condition limit, not the introduction serial for the Walbro carburetor. This record does not cover the separate 044 arctic replacement procedure.
- Summary remark 1 says the original complete C3M-S5G is no longer available from the factory; remark 2 retains its component parts as spares. This is historical availability, not current stock. Introduction of the Walbro modification is in progress, without a numeric production cutoff. Type data is stamped on the carburetor; the source performance-improvement claim is not project test evidence.
Source: TI 3/1996, p. 1 · TI 3/1996, p. 2 — Section 1 service note and section 3 summary / remarks.
Part numbers (2)
- 1128 120 0617 — C3M-S5G carburetorOriginal equipment · 044; check actual carburetor marking
- 1128 120 0619 — HD-10 A carburetor (1996 designation)Conditional replacement · 044; compensator conversion may be required
Historical fitment · 044
044: carburetor revision without a new part number
TI 25/1996 documents a smaller semi-fixed jet and revised carburetor markings, while the complete carburetor part numbers remain unchanged.
- This 044 change replaces the 0.71 mm semi-fixed jet with 1128 121 5602 (0.70 mm). Applies to the carburetor variants listed here, not every 044 carburetor.
- HD-10 A → HD-10 B: 1128 120 0619; HD-11 → HD-11 A: 1128 120 0620. The part number alone does not identify the internal jet revision.
- Introduction was in progress; no serial cutoff is supplied. This is a historical configuration record, not an instruction to rejet unrelated carburetors.
- Original044 complete carburetors include jet item8 (0.71mm); revised HD-10B and HD-11A include item4 (0.70mm). The section2 arrow locates the semi-fixed jet; it is not an H/L mixture-adjustment setting.
- Summary remark1 says complete carburetors are supplied only with the modified semi-fixed jet. Remark2 says the original separate jets are no longer supplied from the factory. This historical supply rule does not prove current stock or authorize arbitrary re-jetting; no removal procedure or torque is printed.
Source: TI 25/1996, p. 2 — Complete section2: jet-location drawing, four designation changes, all11 model-specific summary items, inclusion keys and both availability remarks.
Part numbers (4)
- 1128 120 0619 — HD-10 A / HD-10 B carburetorSame number, revised internals · 044; check type marking and jet revision
- 1128 120 0620 — HD-11 / HD-11 A carburetorSame number, revised internals · 044; check type marking and jet revision
- 1128 121 5601 — Semi-fixed jet 0.71 mmOriginal equipment · 044 carburetors listed in this TI
- 1128 121 5602 — Semi-fixed jet 0.70 mmNew version · 044 revised carburetors listed in this TI
Conditional replacement · 044
044 arctic: thermostat moved to the heater
The arctic configuration changed to the standard HD-10 B carburetor together with a new heating element carrying the thermostat and an additional gasket.
X 37 180 486 — Introduction of the combined carburetor/heater arrangement for the specified arctic variant.
- Applies to 044 arctic, not a blanket carburetor substitution for all 044s.
- New heating element 1128 430 6000 and gasket 1128 129 1100 accompany the new carburetor arrangement. The gasket is fitted between carburetor and heating element.
- The older 1128 434 5101 heater and 1128 430 0501 thermostat remained available for older machines in this TI; the new thermostat is not listed as a separate service item.
- X 37 180 486 is the introduction of this combined arctic configuration, not a model-identification range or permission for an unmatched retrofit.
- The thermostatic switch moves from the carburetor end cover to the heating element; the respective standard carburetor is then used with the new element. Gasket 1128 129 1100 fits between carburetor and element to improve heat distribution according to the source, not a reproduced temperature measurement.
- The original carburetor 1128 120 0620 includes the thermostatic switch; new heating element 1128 430 6000 includes the new switch. The new-switch table entry is not an orderable number: it is unavailable separately. Original carburetor 1128 120 0620 is no longer factory-supplied; standard carburetor 1128 120 0619 is already in inventory. Retention of older heater/switch spares is not permission for an unmatched retrofit or a current-stock claim.
Source: TI 9/1997, p. 3 · TI 9/1997, p. 4 — Complete section3:model-specific arctic carburetor/heater rows,gasket drawing,serial and all supply remarks.
Part numbers (6)
- 1128 120 0620 — HD-11 A carburetorOriginal arctic configuration · 044 arctic with thermostat on carburetor
- 1128 120 0619 — HD-10 B carburetorNew arctic configuration · 044 arctic only with matched new heating arrangement
- 1128 434 5101 — Heating elementOriginal equipment · 044 older arctic heating arrangement
- 1128 430 0501 — Thermostatic switchOriginal service part · 044 older arctic arrangement; not the new integrated thermostat
- 1128 430 6000 — Heating element with thermostatRequired companion · 044 revised arctic heating arrangement
- 1128 129 1100 — GasketRequired companion · Between carburetor and new heating element
Conditional replacement · 044
044: carburetor replacement depends on equipment
TI 47/1997 distinguishes HD-15 service replacements for older non-EPA machines from HD-17 carburetors for the EPA-equipped version.
- Older 044 without EPA equipment: replace HD-10B (1128 120 0619) with HD-15 (1128 120 0625).
- The EPA-equipped 044 uses HD-17 (1128 120 0622). Do not treat the two replacement branches as unconditional substitutes.
- The source requires new limiter caps after removal during repair; adjustment and cap-fitting procedure remains in the TI, not inferred from a parts match.
- Introduction is stated as the start of EPA-version production, with no numeric serial cutoff.
- Except for limiter caps and adjusting screws, the non-EPA service HD-15 is stated to be technically the same as its EPA counterpart HD-17; this does not remove the equipment-dependent replacement rule.
- The summary lists original HD-10B with items 9, 10, 12 and 14; new HD-15 includes 9, 10, 12, 14 and 15; EPA HD-17 includes 9, 11, 13 to 16. These are printed inclusion lists, not permission to infer omitted items.
- Original complete carburetor no longer available from the factory; all other parts remain as before. These are dated 1997 supply statements, not current stock. The separate cap-setting notes retain lean-stop versus screw-seat reference points.
Source: TI 47/1997, p. 2 · TI 47/1997, p. 3 · TI 47/1997, p. 5 — Sections 1–1.7: carburetor and service branches; full section, drawing and summary context reviewed in batch26.
Part numbers (3)
- 1128 120 0619 — Carburetor HD-10BOriginal equipment · 044 original configuration
- 1128 120 0625 — Carburetor HD-15Conditional service replacement · 044 older machine without EPA equipment
- 1128 120 0622 — Carburetor HD-17EPA configuration · 044 EPA-equipped version only
Conditional replacement · 044
044: limiter-cap grommet and revised filter base
The HD filter base changed shape without changing its number; the new grommet accommodates the limiter-cap recess.
- Grommet 1128 123 7502 is for the carburetor equipped with limiter caps; it replaces 1128 123 7500 in that configuration.
- HD filter base 1128 124 3408 retains its number despite the shape change. The revised shape allows grommet removal without removing the base.
- Replacement bases without setting symbols are documented for original and new versions. Do not use an embossed carburetor setting as proof that the installed carburetor matches it.
- The new grommet sits in the limiter-cap recess and flush with the caps. Standard-production filter bases bear H = 3/4, L = 1/4 setting symbols; neutral replacement bases omit them.
- Introduction is from the start of EPA-version production. Original grommet remains a spare; only the modified filter base is factory-supplied. These are historical availability notes, not numeric serial boundaries.
Source: TI 47/1997, p. 5 · TI 47/1997, p. 6 — Section 2: grommet and 044 filter base; full section, drawing and summary context reviewed in batch26.
Part numbers (3)
- 1128 123 7500 — GrommetOriginal configuration · 044 original carburetor opening
- 1128 123 7502 — GrommetConfiguration-specific replacement · 044 limiter-cap carburetor
- 1128 124 3408 — HD filter baseSame number, revised shape · 044 HD configuration; inspect revision
Conditional replacement · 044
044: HD-17 → HD-17 A keeps the carburetor number
TI 35/1999 changes the main jet and low-speed screw without changing carburetor number 1128 120 0622.
- 1128 120 0622 covers both HD-17 and HD-17 A; inspect the version, not just the assembly number.
- Standard full-load jet changes from 1128 121 5602 (0.70) to 1128 121 5605 (0.66). The 1122 121 5604 (0.64) jet is explicitly a high-altitude option, not the universal replacement.
- Low-speed screw 1128 122 6804 → 1128 122 6806 changes the taper from 10° to 11°. These are HD-17/17 A components, not the HD-15 screw pair.
- The summary lists both carburetor versions including full-load jet item 3 and low-speed screw item 4. High-altitude jet item 5 is separate, not a stated included component.
- In the high-altitude row, previous jet 1128 121 5605 is replaced by 1122 121 5604. The same 1128 121 5605 is the new standard full-load jet in item 3; its role depends on configuration, not an unconditional supersession chain.
- Introduction is in progress without a serial threshold. For all five summary rows, only modified versions were available from the factory at the bulletin date; no current stock claim is made.
Source: TI 35/1999, p. 2 · TI 35/1999, p. 3 — Sections 2–2.3: HD-17 revision.
Part numbers (6)
- 1128 120 0622 — HD-17 / HD-17 A carburetorSame number, revised components · 044; identify carburetor version
- 1128 121 5602 — 0.70 full-load jetOriginal standard jet · 044 HD-17
- 1128 121 5605 — 0.66 full-load jetRevised standard jet · 044 HD-17 A
- 1122 121 5604 — 0.64 high-altitude jetConditional option · 044 HD-17 A high-altitude configuration
- 1128 122 6804 — 10° low-speed screwOriginal version · 044 HD-17
- 1128 122 6806 — 11° low-speed screwRevised version · 044 HD-17 A
Conditional replacement · 044
044: HD-15 A → HD-15 B keeps the carburetor number
The low-speed screw changes while carburetor number 1128 120 0625 stays the same.
- 1128 120 0625 covers HD-15 A and HD-15 B in this TI. The number alone does not identify the revision.
- Low-speed screw 1128 122 6805 (10° taper) → 1128 122 6807 (11° taper). Do not substitute the separate HD-17 screw pair based on appearance.
- The TI does not establish the preceding HD-15 → HD-15 A step; this record must not invent that missing revision history.
- The summary lists each carburetor version including its low-speed screw (item 3). Introduction is in progress without a serial threshold.
- For all three summary rows, only modified versions were available from the factory at the bulletin date. This historical supply statement does not identify current stocks or the preceding HD-15 revision.
Source: TI 35/1999, p. 3 — Section 3: HD-15 A / HD-15 B.
Part numbers (3)
- 1128 120 0625 — HD-15 A / HD-15 B carburetorSame number, revised component · 044; identify exact revision
- 1128 122 6805 — 10° low-speed screwHD-15 A version · 044 HD-15 A
- 1128 122 6807 — 11° low-speed screwHD-15 B version · 044 HD-15 B
Conditional replacement · 044 / 046
044 / 046: valve-jet revision in the 1997 carburetor change
TI 47/1997 changes valve jet 1128 121 5403 to 1128 121 5404 in the described HD carburetor revision.
- Applies to the described HD-15/HD-17 (044) and HD-14/HD-16 (046) configurations, not every carburetor fitted to these models.
- The previous valve jet remains available as a spare in the source table. A table revision is not permission to mix all other old/new carburetor components.
- The bulletin attributes the valve-jet change to optimized part-load behavior and reduced fuel consumption; these are manufacturer claims, not measured results. Diagram139TI015 identifies valve jet(1) separately from fixed jet(2).
- O-rings on both adjusting screws improve sealing against secondary air. Knurled screw heads retain the limiter caps; molded stops in the insert bores limit cap travel. Diagram139TI011 defines items1–5; its visible item6 is not defined by the printed legend, so no component identity is invented.
Source: TI 47/1997, p. 2 · TI 47/1997, p. 5 — Sections 1 and 1.7: valve jet; full section, drawing and summary context reviewed in batch26.
Part numbers (2)
- 1128 121 5403 — Valve jetPrevious version · 044 / 046 described HD carburetors
- 1128 121 5404 — Valve jetRevised version · 044 HD-15/HD-17 and 046 HD-14/HD-16 change
Conditional replacement · 044
044: non-EPA carburetor screw and spring revisions
The service carburetor has its own adjusting screws and springs, distinct from the EPA screw/cap configuration.
- Applies to HD-15 service carburetor for older 044 without EPA equipment, not HD-17 EPA.
- Low-speed screw: 4116 122 6800 → 1128 122 6803. High-speed screw: 1127 122 6700 → 1127 122 6701. Two springs: 4116 122 3001 → 1128 122 3003.
- The new service carburetor includes sealing rings (item 15), but the bulletin gives no separate order number for them.
- Previous screws and springs remain available as spares. This record does not authorize fitting non-EPA screws to an EPA carburetor.
- The summary specifies two sealing rings and explicitly marks them unavailable as separate items, not merely lacking a printed order number. Adjusting-screw O-rings seal against the carburetor body. Introduction is from the start of EPA-version production; all other parts remain as before.
Source: TI 47/1997, p. 2 · TI 47/1997, p. 5 — Sections 1.2 and 1.7: non-EPA carburetor subparts; full section, drawing and summary context reviewed in batch26.
Part numbers (6)
- 4116 122 6800 — Low-speed screwPrevious version · 044 original non-EPA HD configuration
- 1128 122 6803 — Low-speed screwRevised non-EPA version · 044 HD-15
- 1127 122 6700 — High-speed screwPrevious version · 044 original non-EPA HD configuration
- 1127 122 6701 — High-speed screwRevised non-EPA version · 044 HD-15
- 4116 122 3001 — SpringPrevious version · 044 original non-EPA HD configuration
- 1128 122 3003 — SpringRevised version; two · 044 HD-15
Conditional replacement · 044
044: EPA screws require new limiter caps after servicing
EPA adjusting screws and caps form a distinct configuration; removed caps must not be reused.
- HD-17 EPA uses low-speed screw 1128 122 6804, high-speed screw 1128 122 6703 and two caps 4203 121 2700.
- After repair and specified adjustment, fit new limiter caps. Removed caps must not be reused.
- The table includes two springs 1128 122 3003 and sealing rings; the rings are not available separately in this bulletin.
- Do not substitute the non-EPA screw set. This parts note is not a standalone carburetor adjustment procedure.
- The summary specifies two sealing rings and explicitly marks them unavailable as separate items, not merely lacking a printed order number. Adjusting-screw O-rings seal against the carburetor body. Introduction is from the start of EPA-version production; all other parts remain as before.
Source: TI 47/1997, p. 2 · TI 47/1997, p. 5 — Sections 1–1.7: EPA screws and limiter caps; full section, drawing and summary context reviewed in batch26.
Part numbers (4)
- 1128 122 6804 — EPA low-speed screwEPA configuration · 044 HD-17
- 1128 122 6703 — EPA high-speed screwEPA configuration · 044 HD-17
- 4203 121 2700 — Limiter capRequired new caps; two · 044 HD-17 after servicing
- 1128 122 3003 — SpringConfiguration component; two · 044 HD-17
Historical fitment · 044
044: optional high-altitude jet for HD-15 / HD-17
TI 29/1998 lists the optional 0.66 mm jet by stamped carburetor type; this is not the standard jet or a universal replacement.
- Select by the type stamped on the carburetor body, not the saw model or assembly part number alone. The cited rows name HD-15 and HD-17 without later revision suffixes.
- Optional jet 1128 121 5605 has a 0.66 mm bore. The source restricts the smaller-bore option to very high altitude when the normal adjustment range is insufficient.
- Do not use the smaller-bore high-altitude jet at lower altitudes: the source warns of an overly lean mixture and engine damage. No universal altitude threshold is supplied.
- Replacement is for trained personnel; press-fit positioning depends on the separate Carburetors handbook. This lookup is not a complete installation or adjustment procedure.
- The scan table has no USA-only asterisk on these rows. This does not establish universal regulatory approval or applicability to later carburetor suffixes.
- This bulletin does not establish the missing HD-15 to HD-15 A revision or override later variant-specific instructions.
Source: TI 29/1998, p. 1 · TI 29/1998, p. 2 — Important notes and table: HD-15 / HD-17 rows.
Part numbers (3)
- 1128 120 0625 — Carburetor HD-15Source type association · 044; stamped HD-15 only
- 1128 120 0622 — Carburetor HD-17Source type association · 044; stamped HD-17 only
- 1128 121 5605 — High-altitude fixed jet, 0.66 mmOptional, not standard · HD-15 / HD-17; high-altitude conditions only
Historical fitment · 044
044 Arctic: HD-11 replacement and historical availability
HD-11 replaces C3M-S24; replacing the earlier C3M-S23 also requires a separate heater and wiring conversion.
- The original C3M-S24 1128 120 0618 is replaced by HD-11 1128 120 0620, stated here as the only replacement carburetor for all 044 Arctics. This is the 1996 source statement, not a current-stock claim or approval for all carburetors on the shared IPL sheet.
- C3M-S23 1128 120 0616 was fitted to carburetor-heating-only saws up to X 30 991 111. HD-11 installation on that configuration requires heater 1128 434 5101 and harness modification. That serial is an old-configuration limit, not the introduction serial of HD-11.
- The source says C3M-S23 is no longer available. The summary separately marks original C3M-S24 and C3M-S5G complete carburetors unavailable from the factory, while their component parts remain spares. The earlier TI07/1995 retention statement is not overwritten; availability changed between the dated sources.
- Introduction is in progress, with no numeric Walbro production cutoff. Read the carburetor type marking. The stated performance improvement is a vendor claim, not a measured result.
- HD-11 differs from HD-10 A by thermostatic switch 1128 430 0501 and mounting hardware. HD-11 includes items 1–29 and 32–37; switch item 37 itself includes terminal item 38. Heater item 39 is separately listed, outside the stated complete-carburetor inclusion ranges. Do not assume the heater is supplied with the carburetor.
Source: TI 3/1996, p. 1 · TI 3/1996, p. 2 · TI 3/1996, p. 3 · TI 3/1996, p. 4 — Section 2, summary and complete-carburetor inclusion rows.
Part numbers (5)
- 1128 120 0618 — C3M-S24Original complete carburetor · 044 Arctic
- 1128 120 0616 — C3M-S23Earlier carburetor-heating-only configuration · Up to X 30 991 111
- 1128 120 0620 — HD-11Conditional replacement · 044 Arctic; actual heater configuration matters
- 1128 434 5101 — Separate heating elementRequired S23 conversion companion · Not included by the complete-carburetor item ranges
- 1128 430 0501 — Thermostatic switchHD-11 distinguishing part · Includes terminal item 38
Historical fitment · 044
044 Arctic: HD-11 harness conversion dependencies
The S23-to-HD-11 conversion requires a new terminal, insulating tube and separate heater; the referenced crimping detail remains unavailable.
- For the earlier C3M-S23 carburetor-heating-only configuration up to X 30 991 111, the printed sequence is: disconnect thermostatic switch/wiring harness; pull the tab receptacle off the heater; remove the carburetor; cut off the tab receptacle; slip insulating tube 1121 442 0402 over the wire.
- Use crimping tool 5910 890 8210 to attach terminal socket 1118 431 6700. Proper crimping is delegated to TI47/1992 page 5, absent from the retained 690-TI inventory. No missing die selection, strip length, crimp dimension or pull-test value is invented. This note is not a complete executable repair procedure.
- Install the new carburetor and heater 1128 434 5101 with TI07/1995 as the heater reference. Connect switch and heater to the harness, slip the tube over the connector and position wires as in TI07/1995 chapter 6. The page 2 drawing shows the connector/heater arrangement; it supplies no connector pinout.
- TI07/1995 routing is retained and separately reviewed. Its printed tube is 1121 442 0400, whereas this conversion explicitly specifies 1121 442 0402. These are source-specific numbers, not an established alias or blanket tube supersession.
- Page 2 calls 1118 431 6700 a terminal socket; page 4 item 38 calls the same number a terminal pin and includes it in switch item 37. Preserve both labels; do not infer connector gender or an additional unlisted mating part.
Source: TI 3/1996, p. 1 · TI 3/1996, p. 2 · TI 3/1996, p. 4 — Section 2 service note and page 2 full conversion sequence; items 37–39.
Part numbers (4)
- 1121 442 0402 — Insulating tubeHarness conversion companion · Earlier S23 to HD-11 conversion
- 5910 890 8210 — Crimping toolSpecified service tool · Detailed crimp procedure missing
- 1118 431 6700 — Terminal socket / terminal pin, source labelsHarness conversion terminal · Also item 38 included in switch item 37
- 1128 434 5101 — Heating elementSeparate conversion companion · Earlier S23 to HD-11 conversion
Historical fitment · 044
044 HD-10 A / HD-11: fuel-metering component roster
The 1996 spare-parts table identifies inlet, jet, metering and pump components by original item number.
- The table belongs to 044 HD-10 A 1128 120 0619 and 044 WZVH HD-11 1128 120 0620. Both complete assemblies include items 1–29. These are the original 1996 versions, not automatic internal-parts compatibility with later HD-10B, HD-11A, HD-15C or HD-17C labels on the shared catalog sheet.
- Remark 1 means already available for other models. It supplies no exact other-model list and does not authorize applying every item to every carburetor. Unmarked rows do not establish a numeric production cutoff. The printed introduction is in progress.
- Inlet needle, control lever and spring are distinct items 1–3. Valve jet item 7 and fixed jet item 8 are distinct; no jet bore, setting or calibration value is printed. End cover item 11 is separate from the version-specific covers 30 and 32.
- The exploded drawing supplies original item locations, not current IPL row positions. No tightening torque, screw quantity or universal diaphragm-stack procedure is inferred from the drawing.
Source: TI 3/1996, p. 3 · TI 3/1996, p. 4 — Section 4 items 1–15 and remark 1.
Part numbers (15)
- 4116 121 5100 — Item 1: Inlet needleListed component; already available for other models · 044 HD-10 A / HD-11, original 1996 versions
- 4116 121 5000 — Item 2: Inlet control leverListed component; already available for other models · 044 HD-10 A / HD-11, original 1996 versions
- 1128 122 3002 — Item 3: SpringListed component · 044 HD-10 A / HD-11, original 1996 versions
- 1113 121 9200 — Item 4: SpindleListed component; already available for other models · 044 HD-10 A / HD-11, original 1996 versions
- 1114 122 7400 — Item 5: Round head screwListed component; already available for other models · 044 HD-10 A / HD-11, original 1996 versions
- 4117 122 9402 — Item 6: Screw plugListed component; already available for other models · 044 HD-10 A / HD-11, original 1996 versions
- 1128 121 5403 — Item 7: Valve jetListed component · 044 HD-10 A / HD-11, original 1996 versions
- 1128 121 5601 — Item 8: Fixed jetListed component · 044 HD-10 A / HD-11, original 1996 versions
- 1128 129 0906 — Item 9: GasketListed component · 044 HD-10 A / HD-11, original 1996 versions
- 4116 121 4700 — Item 10: Metering diaphragmListed component; already available for other models · 044 HD-10 A / HD-11, original 1996 versions
- 1128 121 0801 — Item 11: End coverListed component · 044 HD-10 A / HD-11, original 1996 versions
- 1121 122 7101 — Item 12: Collar screwListed component; already available for other models · 044 HD-10 A / HD-11, original 1996 versions
- 1114 121 7800 — Item 13: StrainerListed component; already available for other models · 044 HD-10 A / HD-11, original 1996 versions
- 4116 121 4800 — Item 14: Pump diaphragmListed component; already available for other models · 044 HD-10 A / HD-11, original 1996 versions
- 4116 129 0902 — Item 15: GasketListed component; already available for other models · 044 HD-10 A / HD-11, original 1996 versions
Historical fitment · 044
044 HD-10 A / HD-11: control shafts and adjustment screws
The original throttle/choke parts and adjustment screws remain individually identifiable without importing later carburetor revisions.
- The table belongs to 044 HD-10 A 1128 120 0619 and 044 WZVH HD-11 1128 120 0620. Both complete assemblies include items 1–29. These are the original 1996 versions, not automatic internal-parts compatibility with later HD-10B, HD-11A, HD-15C or HD-17C labels on the shared catalog sheet.
- Remark 1 means already available for other models. It supplies no exact other-model list and does not authorize applying every item to every carburetor. Unmarked rows do not establish a numeric production cutoff. The printed introduction is in progress.
- Torsion springs 16 and 21 have different part numbers. Throttle shaft item 17 and choke shaft item 22 remain distinct, as do E-clips 18 and 23 and shutter screws 20 and 25.
- Spring item 27 is drawn at both mixture-screw positions; high-speed screw 28 and low-speed screw 29 have distinct numbers. The table does not specify a complete-parts-kit spring quantity or H/L adjustment turns. No quantity or mixture setting is inferred.
Source: TI 3/1996, p. 3 · TI 3/1996, p. 4 — Section 4 items 16–29 and remark 1.
Part numbers (14)
- 1127 122 3205 — Item 16: Torsion springListed component; already available for other models · 044 HD-10 A / HD-11, original 1996 versions
- 1127 120 7100 — Item 17: Throttle shaft with leverListed component; already available for other models · 044 HD-10 A / HD-11, original 1996 versions
- 1117 122 9000 — Item 18: E-clipListed component; already available for other models · 044 HD-10 A / HD-11, original 1996 versions
- 1128 121 3302 — Item 19: Throttle shutterListed component · 044 HD-10 A / HD-11, original 1996 versions
- 1115 122 7400 — Item 20: Round head screwListed component; already available for other models · 044 HD-10 A / HD-11, original 1996 versions
- 1127 122 3200 — Item 21: Torsion springListed component; already available for other models · 044 HD-10 A / HD-11, original 1996 versions
- 1127 120 7200 — Item 22: Choke shaft with leverListed component; already available for other models · 044 HD-10 A / HD-11, original 1996 versions
- 1123 122 9000 — Item 23: E-clipListed component; already available for other models · 044 HD-10 A / HD-11, original 1996 versions
- 1122 121 2900 — Item 24: Choke shutterListed component; already available for other models · 044 HD-10 A / HD-11, original 1996 versions
- 1110 122 7400 — Item 25: Round head screwListed component; already available for other models · 044 HD-10 A / HD-11, original 1996 versions
- 1127 122 6200 — Item 26: Idle speed screwListed component; already available for other models · 044 HD-10 A / HD-11, original 1996 versions
- 4116 122 3001 — Item 27: SpringListed component; already available for other models · 044 HD-10 A / HD-11, original 1996 versions
- 1127 122 6700 — Item 28: High speed screwListed component; already available for other models · 044 HD-10 A / HD-11, original 1996 versions
- 4116 122 6800 — Item 29: Low speed screwListed component; already available for other models · 044 HD-10 A / HD-11, original 1996 versions
Historical fitment · 044
044 HD-10 A versus HD-11: cover and heater hardware
Complete-carburetor inclusion ranges differ; the heater is separate and the shared drawing is not a universal package-content list.
- HD-10 A 1128 120 0619 includes items 1–31, including end cover 1127 121 0800 (30) and oval head screw 1114 122 7100 (31). HD-11 1128 120 0620 includes items 1–29 and 32–37 instead.
- The HD-11 branch lists end cover 1128 121 0802 (32), oval head screw 1128 122 7101 (33), clip 1128 122 9301 (34), washers 1128 121 8602 (35) and 1128 121 8603 (36), and thermostatic switch 1128 430 0501 (37). Switch item 37 includes terminal pin 1118 431 6700 (38).
- Heating element 1128 434 5101 (39) is listed separately, outside both complete-carburetor inclusion ranges. Washer 36 appears in the common exploded illustration, but the HD-10 A text stops at item 31; do not silently add item 36 to its stated package contents or infer stand-alone fit from drawing proximity.
- Remark 1 marks items 30, 31, 34, 38 and 39 as already available for other models. No exact other models, current availability or hardware-conversion kit is established.
- These original 1996 HD-10 A / HD-11 names stay distinct from later catalog designations. The HD-11 service-replacement rule does not make its heater hardware universally interchangeable with every carburetor on this sheet.
Source: TI 3/1996, p. 3 · TI 3/1996, p. 4 — Section 4 complete assemblies and items 30–39.
Part numbers (12)
- 1128 120 0619 — HD-10 A; includes items 1–31Complete assembly · Original 044 non-Arctic Walbro branch
- 1128 120 0620 — HD-11; includes items 1–29 and 32–37Complete assembly · 044 Arctic branch
- 1127 121 0800 — Item 30: End coverListed component; already available for other models · Exact HD-10 A / HD-11 inclusion branch; heater 39 separate
- 1114 122 7100 — Item 31: Oval head screwListed component; already available for other models · Exact HD-10 A / HD-11 inclusion branch; heater 39 separate
- 1128 121 0802 — Item 32: End coverListed component · Exact HD-10 A / HD-11 inclusion branch; heater 39 separate
- 1128 122 7101 — Item 33: Oval head screwListed component · Exact HD-10 A / HD-11 inclusion branch; heater 39 separate
- 1128 122 9301 — Item 34: ClipListed component; already available for other models · Exact HD-10 A / HD-11 inclusion branch; heater 39 separate
- 1128 121 8602 — Item 35: WasherListed component · Exact HD-10 A / HD-11 inclusion branch; heater 39 separate
- 1128 121 8603 — Item 36: WasherListed component · Exact HD-10 A / HD-11 inclusion branch; heater 39 separate
- 1128 430 0501 — Item 37: Thermostatic switch; includes item 38Listed component · Exact HD-10 A / HD-11 inclusion branch; heater 39 separate
- 1118 431 6700 — Item 38: Terminal pinListed component; already available for other models · Exact HD-10 A / HD-11 inclusion branch; heater 39 separate
- 1128 434 5101 — Item 39: Heating elementListed component; already available for other models · Exact HD-10 A / HD-11 inclusion branch; heater 39 separate
Historical fitment · 044
044 HD-10 A / HD-11: parts-kit contents
Kit 1128 007 1066 includes only the item ranges printed in the 1996 table, not every listed carburetor part.
- Carburetor parts kit 1128 007 1066 includes items 1–3, 9, 10, 13–15 and 27: inlet needle, inlet control lever, its spring, metering gasket/diaphragm, strainer, pump diaphragm/gasket and mixture-screw spring.
- Items not named in this inclusion row are not established as kit contents. In particular, the valve/fixed jets, H/L screws, covers, thermostatic switch and heater are not included by the printed ranges.
- The exploded drawing repeats item 27 at the mixture screws, but the kit row supplies no explicit quantity. Preserve the item inclusion without inferring how many springs the kit contains.
- This is the historical HD-10 A / HD-11 parts kit in this table, not an alias for the earlier Zama kit, verified compatibility with later carburetor internals or a current package-content promise.
Source: TI 3/1996, p. 3 · TI 3/1996, p. 4 — Section 4 final parts-kit row, cross-read with items 1–29.
Part numbers (10)
- 1128 007 1066 — Carburetor parts kitHistorical kit · 044 HD-10 A / HD-11 table
- 4116 121 5100 — Item 1: Inlet needleListed component; already available for other models · Included by item reference in kit 1128 007 1066
- 4116 121 5000 — Item 2: Inlet control leverListed component; already available for other models · Included by item reference in kit 1128 007 1066
- 1128 122 3002 — Item 3: SpringListed component · Included by item reference in kit 1128 007 1066
- 1128 129 0906 — Item 9: GasketListed component · Included by item reference in kit 1128 007 1066
- 4116 121 4700 — Item 10: Metering diaphragmListed component; already available for other models · Included by item reference in kit 1128 007 1066
- 1114 121 7800 — Item 13: StrainerListed component; already available for other models · Included by item reference in kit 1128 007 1066
- 4116 121 4800 — Item 14: Pump diaphragmListed component; already available for other models · Included by item reference in kit 1128 007 1066
- 4116 129 0902 — Item 15: GasketListed component; already available for other models · Included by item reference in kit 1128 007 1066
- 4116 122 3001 — Item 27: SpringListed component; already available for other models · Included by item reference in kit 1128 007 1066
Service note · 044 / 046
044 / 046 EPA: capped standard setting
H = 3/4 and L = 1/4 open from the lean stop; not from screw seats.
- This note applies to the described EPA HD-17(044) and HD-16(046) carburetors with limiter caps. Factory optimum setting is the standard setting: H = 3/4 turn and L = 1/4 turn open, starting from the lean stop in each case. It is not the uncapped basic setting and not a setting for every HD carburetor.
- The integral stops in the insert bores limit corrections to 270 degrees. Caps are retained by the knurled screw heads and sit flush with the insert, at the bottom of the dome. The source describes this range as permitting high-altitude leaning while limiting enrichment beyond its EPA limits.
- For unsatisfactory high-altitude running, the printed sequence is check standard setting, warm engine, then slight clockwise(leaner) corrections of H and L. Too lean a setting exceeds maximum permissible speed and risks engine damage. No numeric maximum speed or altitude threshold is printed here; no value is borrowed from the046 C catalyst instruction.
Source: TI 47/1997, p. 2 · TI 47/1997, p. 3 — Complete sections1.1–1.3 and cap-stop diagram132TI022.
No additional parts-table entry added.
Service note · 044 / 046
044 / 046 EPA: cap removal and basic setting
Uncapped H and L each start one full turn open from their seats.
- Applies to the described EPA HD-17(044) and HD-16(046) configuration, not every carburetor on these model sheets. Remove caps to replace screws or clean the carburetor. First turn the caps/screws counterclockwise to their stops, then screw puller5910 890 4500 into each cap counterclockwise until it comes off. Do not reuse removed caps.
- After fitting adjusting screws and with caps removed, start with screws against their seats: open H one full turn and L one full turn. This seat-referenced basic setting must not be confused with the capped standard setting measured from lean stops.
- Always fit new caps. Insert with lug positions exactly as drawing132TI023, then push onto screws until flush with insert(1). The source says the resulting position equals the standard setting, but prints cross-reference1.2 where the standard-setting section is1.3. Preserve this reference mismatch; the source drawing remains the lug-orientation reference.
- Set idle speed to2500 rpm with idle-speed screw LA and use a tachometer. This is not the maximum permissible engine speed. This historical procedure does not authorize unattended adjustment or hardware operation.
Source: TI 47/1997, p. 3 · TI 47/1997, p. 4 — Complete sections1.2,1.4–1.4.3; diagrams139TI013 and132TI023.
Part numbers (1)
- 5910 890 4500 — Limiter-cap pullerSpecified service tool · 044 HD-17 /046 HD-16 EPA cap removal
Service note · 044 / 046
044 / 046: EPA label and 50:1 approval context
The1997 approval used50:1; referenced TI27/1997 remains unavailable in this corpus.
- The cover states that the described modifications achieve EPA compliance except sections4.2,5.2 and6.1. There is no body subsection6.1 in this issue: front hand guard is section6 and flush-cut version is7.1. The exception label remains unresolved; do not silently assign an emission role to either change.
- The illustrated factory IMPORTANT ENGINE INFORMATION label states conformity to US EPA Phase1 utility/lawn-and-garden engine regulations and refers to the owner manual for maintenance specifications and adjustment. Its engine-family/type/displacement/date fields are an example, not an observed machine identity or evidence that any repaired machine is compliant.
- Section1.5 says EPA approval was obtained with50:1 fuel/oil mix and no emission measurements are available for other ratios. This is the scope of the original approval evidence, not a claim that alternate ratios were tested or a universal fuel recommendation.
- Cover and sections1.5–1.6 refer to TI27/1997, including Federal Emission Control Systems Utility Engines. TI27/1997 is absent from the retained690-TI inventory and tipages scan filenames; that referenced detail remains a source gap, not proof of absence everywhere.
Source: TI 47/1997, p. 1 · TI 47/1997, p. 4 — Cover compliance statement/label and complete sections1.5–1.6.
No additional parts-table entry added.
Wrong number or missing part for the 044? Report a correction →