← 044/046 · MS 440/460/461

Stihl 1128 · Section N · 13 of 17 · 54 parts

Carburetor C3M-S5G, S24, S5E, S20, S22, S23

Fits 044.

Parts diagrams →

Historical fitment & changes (9) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
110111213141516171819220212223242425262627282933031323334353637373839440550515253545556576789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (54)

PosPart numberDescriptionQty
1 4116 121 5100 Inlet needle 1
2 1125 121 5000 Inlet control lever 1
3 1128 122 3000 Spring 1
4 1120 121 9200 Spindle 1
5 1120 122 6600 Collar screw 1
6 1125 121 0700 Cup plug 1
7 1125 129 0901 Gasket 1
8 1125 121 4700 Metering diaphragm 1
9 1128 121 5400 Valve jet Fitment / change note → 1
10 1128 121 0800 End cover 1
11 1120 122 6601 Collar screw 4
12 1123 121 7800 Strainer 1
13 1125 122 4200 Clamp 1
14 1128 121 4802 Pump diaphragm Fitment / change note → 1
15 1125 129 0900 Gasket 1
16 1128 122 3200 Torsion spring 1
17 1128 120 7100 Throttle shaft with lever Fitment / change note → 1
18 1125 122 9001 E-clip 1
19 1128 121 3300 Throttle shutter 1
20 1128 122 3201 Torsion spring 1
21 1128 120 7200 Choke shaft with lever 1
22 1125 122 9002 E-clip 1
23 1128 121 2901 Choke shutter 1
24 1125 122 7403 Round head screw 2
25 1128 122 6200 Idle speed adjustment screw 1
26 1120 122 3005 Spring 2
27 1125 122 6700 High speed adjustment screw Fitment / change note → 1
28 1128 122 6800 Low speed adjustment screw Fitment / change note → 1
29 1128 120 0800 End cover 1
30 1120 122 7800 Oval head screw 1
31 1128 120 0801 End cover 1
32 1128 122 7700 Oval head screw 1
33 1128 122 9301 Clip 1
34 1128 122 1501 Washer 1
35 1128 122 1502 Washer 1
36 1128 430 0501 Switch Fitment / change note → 1
37 1118 431 6700 NLA Terminal socket Fitment / change note → no longer available from factory 1
38 1128 434 5101 Heating element Fitment / change note → 1
39 1118 431 6600 NLA Terminal pin no longer available from factory 1
40 1124 121 9100 Bushing 1
50 1128 122 7100 Screw Fitment / change note → 1
51 1128 431 7300 Contact Fitment / change note → 1
52 1128 430 0500 Switch Fitment / change note → → replaced by 1128 430 0501 TI 7/1995 1
53 1125 121 0803 End cover 1
54 1128 121 5401 Valve jet Fitment / change note → 1
55 1125 122 6701 High speed adjustment screw Fitment / change note → 1
56 1128 122 6802 Low speed adjustment screw Fitment / change note → 1
57 1128 120 7103 Throttle shaft with lever Fitment / change note → 1
Not numbered on the diagram — assemblies, kits and options
— 1128 120 0617 Carburetor C3M-S5G Fitment / change note → → replaced by 1128 120 0619 TI 3/1996 no longer available from factory 1
— 1128 120 0618 Carburetor C3M-S24 Fitment / change note → → replaced by 1128 120 0620 TI 3/1996 no longer available from factory 1
— 1128 007 1065 Set of carburetor parts Fitment / change note → 1
— 1128 120 0616 Carburetor C3M-S23 Fitment / change note → 1
— 1128 120 0611 Carburetor C3M-S22 Fitment / change note → no longer available from factory 1
— 1128 120 0601 Carburetor C3M-S5E Fitment / change note → no longer available from factory 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Conditional replacement · 044

Zama to Walbro: check the compensator

TI 03/1996 replaces C3M-S5G 1128 120 0617 with HD-10 A 1128 120 0619 on the 044. The later IPL uses the same number for HD-10B; this record preserves the bulletin’s earlier designation.

  • When replacing a carburetor without a compensator connection on a saw up to X 026 452 476, conversion to a compensator is required. TI 03/1996 refers to TI 54/1992, “Air filter”, for the conversion.
  • That serial is a retrofit-condition limit, not the introduction serial for the Walbro carburetor. This record does not cover the separate 044 arctic replacement procedure.
  • Summary remark 1 says the original complete C3M-S5G is no longer available from the factory; remark 2 retains its component parts as spares. This is historical availability, not current stock. Introduction of the Walbro modification is in progress, without a numeric production cutoff. Type data is stamped on the carburetor; the source performance-improvement claim is not project test evidence.

Source: TI 3/1996, p. 1 · TI 3/1996, p. 2 — Section 1 service note and section 3 summary / remarks.

Part numbers (2)
  • 1128 120 0617 — C3M-S5G carburetorOriginal equipment · 044; check actual carburetor marking
  • 1128 120 0619 — HD-10 A carburetor (1996 designation)Conditional replacement · 044; compensator conversion may be required

Historical fitment · 044

044: standard and heated C3M carburetor serial ranges

The three production columns distinguish standard and carburetor-heated configurations; a shared 044 label does not make their carburetors interchangeable.

  • Column A, up to X 26 452 475: standard C3M-S5E 1128 120 0601; no carburetor-heating version is listed (dash, not evidence of universal absence).
  • Column B, from X 26 452 476 up to X 28 047 977: standard C3M-S20 1128 120 0608; heated C3M-S22 1128 120 0611.
  • Column C, from X 28 047 978: standard C3M-S5G 1128 120 0617; heated C3M-S23 1128 120 0616. These are historical printed X-prefix ranges, not converted global numeric serial ranges.
  • All column-B carburetors have a compensator and modified idle system. Column C returns to the column-A idle system, so the source re-applies column-A replacement parts as qualified by the summary; not blanket interchange of complete carburetors.
  • Some carburetors marked C3M-S20 A were upgraded to the C3M-S5G level. A marking or serial alone does not establish the current internals of a repaired saw.
  • The B-to-C summary says old complete B carburetors are no longer factory supplied. Earlier A-to-B component changes refer to unavailable TI54/1992; no missing details are reconstructed. S24 and later HD carburetors on the linked catalog sheet do not inherit these ranges.
  • TI16/1994 is dated March 21, 1994. Historical availability and production statements are not present inventory or verified physical interchange; no successor-model applicability is inferred.

Source: TI 16/1994, p. 3 · TI 16/1994, p. 4 — Sections2 and2.3, standard/heated rows and explanatory notes.

Part numbers (5)
  • 1128 120 0601 — C3M-S5E standard, column AHistorical version · 044 configuration described in this record
  • 1128 120 0608 — C3M-S20 standard, column BHistorical version · 044 configuration described in this record
  • 1128 120 0617 — C3M-S5G standard, column CHistorical version · 044 configuration described in this record
  • 1128 120 0611 — C3M-S22 heated, column BHistorical version · 044 configuration described in this record
  • 1128 120 0616 — C3M-S23 heated, column CHistorical version · 044 configuration described in this record

Historical fitment · 044

044 C3M: B-to-C component changes retain two throttle shafts

Valve jet and adjusting screws change with the return to the earlier idle system. Standard/heated carburetors and automatic-choke carburetors use different throttle-shaft rows.

  • Table items1–4 are pump diaphragm, valve jet, high-speed and low-speed adjusting screws. Standard S20/S5G and heated S22/S23 assemblies include items1–4 plus5; automatic-choke S21/S12B assemblies include items1–4 plus6.
  • Valve jet 1128 121 5401 → 1128 121 5400; high-speed screw 1125 122 6701 → 1125 122 6700; low-speed screw 1128 122 6802 → 1128 122 6800.
  • Item5 standard/heated throttle shaft with lever: 1128 120 7103 → 1128 120 7100. Item6 automatic-choke shaft: 1128 120 7104 → 1128 120 7102. Do not collapse these into one interchangeable throttle shaft.
  • The old valve jet, both adjusting screws and both throttle shafts remain available as spares; all other parts are as before. Pump diaphragm availability differs and is separately recorded. No mixture setting, turn count or RPM is supplied.
  • The summary says introduced from X 28 047 978, subject to the automatic-choke S21 production exception on page3. Earlier A-to-B changes still depend on missing TI54/1992.
  • TI16/1994 is dated March 21, 1994. Historical availability and production statements are not present inventory or verified physical interchange; no successor-model applicability is inferred.

Source: TI 16/1994, p. 3 · TI 16/1994, p. 4 — Sections2.2–2.3, inclusion keys and availability remarks.

Part numbers (10)
  • 1128 121 5401 — Old valve jetHistorical version · 044 configuration described in this record
  • 1128 121 5400 — New valve jetHistorical version · 044 configuration described in this record
  • 1125 122 6701 — Old high-speed screwHistorical version · 044 configuration described in this record
  • 1125 122 6700 — New high-speed screwHistorical version · 044 configuration described in this record
  • 1128 122 6802 — Old low-speed screwHistorical version · 044 configuration described in this record
  • 1128 122 6800 — New low-speed screwHistorical version · 044 configuration described in this record
  • 1128 120 7103 — Old standard/heated throttle shaftHistorical version · 044 configuration described in this record
  • 1128 120 7100 — New standard/heated throttle shaftHistorical version · 044 configuration described in this record
  • 1128 120 7104 — Old automatic-choke throttle shaftHistorical version · 044 configuration described in this record
  • 1128 120 7102 — New automatic-choke throttle shaftHistorical version · 044 configuration described in this record

Historical fitment · 034S / 036 / 044

034S / 036 / 044: pump diaphragm changes inside the same kit

Pump diaphragm 1125 121 4802 changes to 1128 121 4802; carburetor parts kit 1128 007 1065 keeps its number while its contents change.

  • The new pump diaphragm uses a different material; the source does not identify that material or quantify compatibility with fuel blends.
  • The kit summary explicitly names 034S, 036 and 044 and includes item1 (pump diaphragm). The unmodified kit is supplied until existing stocks are exhausted, so kit number alone does not identify the installed diaphragm.
  • The old diaphragm is no longer factory supplied per remark1; this differs from the retained spare status of the valve jet, screws and shafts.
  • 034S is named by the source but has no exact-model catalog sheet bound here. Do not extend it to ordinary034,036QS,MS360 or other successor/variant sheets. The linked036 sheets contain this kit; the044 production serial is not a036/034S serial boundary.
  • TI16/1994 is dated March 21, 1994. Historical availability and production statements are not present inventory or verified physical interchange; no successor-model applicability is inferred.

Source: TI 16/1994, p. 3 · TI 16/1994, p. 4 — Sections2.1 and2.3, pump diaphragm and kit row.

Part numbers (3)
  • 1125 121 4802 — Original pump diaphragmHistorical version · Named kit configurations
  • 1128 121 4802 — Revised-material pump diaphragmHistorical version · Named kit configurations
  • 1128 007 1065 — Carburetor parts kitUnchanged number; changed contents · 034S / 036 / 044 as printed

Conditional replacement · 044

044 Arctic: C3M-S23 to S24 changes heater and thermostat

C3M-S24 uses a separate 8Ω heater between baffle and carburetor and a lower-temperature thermostatic switch; the former C3M-S23 has a bonded 4Ω heater.

X 30 991 112 — Combined carburetor and handle heating on the 044 Arctic version described by TI07/1995; not a universal 044 model boundary.

  • Original C3M-S23 1128 120 0616 changes to C3M-S24 1128 120 0618. The named differences are heating element and thermostatic switch; this is not authority to substitute every carburetor in the shared S5G/S24/S5E/S20/S22/S23 sheet.
  • The bonded original heater is deleted from the new arrangement. Separate heater 1128 434 5101 is between baffle (drawing item 1) and carburetor (item 3), with heater as item 2. At +25°C (77°F): original 4Ω, new 8Ω. Those temperature-qualified component values are not total heating-circuit resistance.
  • Thermostatic switch 1128 430 0500 → 1128 430 0501. Old cut-out +15…+21°C (59…70°F), new +5…+11°C (41…52°F). The source explains that earlier carb-heater cut-out releases more power for faster handle warming; that benefit has not been measured here.
  • The original C3M-S23 summary includes items 1 and 2: screw M3×0.5×8 1128 122 7100 and contact 1128 431 7300. Their new-side cells are blank/deleted; do not carry them into the new assembly or infer that all carburetor hardware is discontinued.
  • Original C3M-S23, screw, contact and thermostatic switch remain available for older machines in the summary. No complete unrestricted old-to-new retrofit procedure is supplied by these rows.
  • Scope is the 044 Arctic combined carburetor/handle-heating configuration in TI 07/1995, dated January 2, 1995. The electrical data differ from earlier handle-only 044W saws; no automatic MS440 or other shared-part applicability. Availability remarks are historical, not current stock.

Source: TI 7/1995, p. 1 · TI 7/1995, p. 2 · TI 7/1995, p. 5 — Sections2.1–2.2 and full carburetor/heater/thermostat summary rows.

Part numbers (7)
  • 1128 120 0616 — Carburetor C3M-S23Original; includes screw and contact · 044 Arctic combined heating; not all 044 variants
  • 1128 120 0618 — Carburetor C3M-S24New combined-heating version · 044 Arctic combined heating; not all 044 variants
  • 1128 122 7100 — Screw M3×0.5×8Original assembly item 1 · 044 Arctic combined heating; not all 044 variants
  • 1128 431 7300 — ContactOriginal assembly item 2 · 044 Arctic combined heating; not all 044 variants
  • 1128 434 5101 — Separate carburetor heating elementNew; 8Ω at +25°C · 044 Arctic combined heating; not all 044 variants
  • 1128 430 0500 — Original thermostatic switchOld cut-out range · 044 Arctic combined heating; not all 044 variants
  • 1128 430 0501 — Revised thermostatic switchNew cut-out range · 044 Arctic combined heating; not all 044 variants

Conditional replacement · 044

044 Arctic: combined-heating harness and wire routing

Harness 1128 440 3012 adds handle-heating wires. The original circuit and routing drawings are essential to keeping the generator wire clear of the flywheel.

X 30 991 112 — Combined carburetor and handle heating on the 044 Arctic version described by TI07/1995; not a universal 044 model boundary.

  • Original harness 1128 440 3007 → 1128 440 3012 adds handle-heating wires; the old harness remains available for older machines. This does not describe a generic harness swap independent of heater/flywheel configuration.
  • Page 4 circuit drawing 132TI004 has generator 1 and round connector 2 feeding two parallel branches: rear heater 3 then front heater 4 and heater switch 5 in series; carburetor heater 6 and thermostatic switch 7 in the other branch. The diagram contains no connector pin numbers or wire-color map; labels 1–7 are component keys, not pinouts. The carb heater is not shown downstream of the handle-heater switch.
  • After ignition-module-area work, push retainer 1 into the crankcase recess, turn round connector 2 as shown in drawing 132TI005, then install the module. Generator wire must lie in crankcase slot 3 well clear of the flywheel. The linked original drawing supplies the orientation, not an inferred universal connector angle.
  • At the thermostatic switch, do not bend or kink the plug connector during installation/removal because the connections may break (drawing 132TI006).
  • Beside the carburetor, loop the wires, push through tube 1121 442 0400 and position as illustrated in 132TI007. The 044 catalog sheets also list insulating hose 1121 442 0402; this bulletin does not establish 0400 → 0402 equivalence or substitution. Only 0400 is the number admitted from this source.
  • Scope is the 044 Arctic combined carburetor/handle-heating configuration in TI 07/1995, dated January 2, 1995. The electrical data differ from earlier handle-only 044W saws; no automatic MS440 or other shared-part applicability. Availability remarks are historical, not current stock.

Source: TI 7/1995, p. 1 · TI 7/1995, p. 3 · TI 7/1995, p. 4 · TI 7/1995, p. 5 — Sections3,5–6, all four circuit/routing diagrams and harness summary.

Part numbers (3)
  • 1128 440 3007 — Original wiring harnessOlder heating configuration · 044 Arctic combined heating; not all 044 variants
  • 1128 440 3012 — Wiring harness with handle-heater wiresNew combined-heating configuration · 044 Arctic combined heating; not all 044 variants
  • 1121 442 0400 — Wire routing tubeTI routing reference; no 0402 alias · 044 Arctic combined heating; not all 044 variants

Historical fitment · 044

044 Arctic: diagnostic chart has a serial gate and separate source gaps

The carburetor-heating chart applies only above X30 991 111; older machines are referred to TI44/1992. Handle-heating test procedure is a separate 044 manual dependency.

X 30 991 112 — Combined carburetor and handle heating on the 044 Arctic version described by TI07/1995; not a universal 044 model boundary.

  • Section 8.2 calls for checking carburetor heating for warm-up running problems, especially below freezing or at idle/part load; poor idling when warm is also an indication. These symptoms are not proof of a heating-system fault.
  • The first chart decision is machine number HIGHER THAN X 30 991 111. NO goes to TI 44/1992, absent from the retained 690-TI corpus. Do not apply the later 8Ω test to the older configuration by default or turn the printed X prefix into a universal numeric model range.
  • YES: check heater resistance at +25°C (77°F), approximately 8Ω. NO leads to fitting a new heating element, then the drawn return loop goes back to the resistance check. No tolerance band beyond approximately is supplied.
  • After heater resistance passes, check switch CLOSING between +11 and +5°C (52…41°F), then OPENING between +5 and +11°C (41…52°F). A failed decision leads to replacing the switch; both replacement arrows return to the initial heater-resistance check, not directly to a healthy result.
  • Only the three YES decisions lead to the chart label carburetor heating system in order. This is the source chart outcome for the stated checks, not an executed hardware test or proof of whole-saw health.
  • Scope is the 044 Arctic combined carburetor/handle-heating configuration in TI 07/1995, dated January 2, 1995. The electrical data differ from earlier handle-only 044W saws; no automatic MS440 or other shared-part applicability. Availability remarks are historical, not current stock.

Source: TI 7/1995, p. 1 · TI 7/1995, p. 2 · TI 7/1995, p. 3 · TI 7/1995, p. 5 · TI 7/1995, p. 6 — Sections8.1–8.2 and complete page6 decision chart; component identity from sections2/7.

Part numbers (2)
  • 1128 434 5101 — Carburetor heating elementReferenced by later-configuration chart · 044 Arctic combined heating; not all 044 variants
  • 1128 430 0501 — Thermostatic switchReferenced by later-configuration chart · 044 Arctic combined heating; not all 044 variants

Historical fitment · 044

044 Arctic: HD-11 replacement and historical availability

HD-11 replaces C3M-S24; replacing the earlier C3M-S23 also requires a separate heater and wiring conversion.

  • The original C3M-S24 1128 120 0618 is replaced by HD-11 1128 120 0620, stated here as the only replacement carburetor for all 044 Arctics. This is the 1996 source statement, not a current-stock claim or approval for all carburetors on the shared IPL sheet.
  • C3M-S23 1128 120 0616 was fitted to carburetor-heating-only saws up to X 30 991 111. HD-11 installation on that configuration requires heater 1128 434 5101 and harness modification. That serial is an old-configuration limit, not the introduction serial of HD-11.
  • The source says C3M-S23 is no longer available. The summary separately marks original C3M-S24 and C3M-S5G complete carburetors unavailable from the factory, while their component parts remain spares. The earlier TI07/1995 retention statement is not overwritten; availability changed between the dated sources.
  • Introduction is in progress, with no numeric Walbro production cutoff. Read the carburetor type marking. The stated performance improvement is a vendor claim, not a measured result.
  • HD-11 differs from HD-10 A by thermostatic switch 1128 430 0501 and mounting hardware. HD-11 includes items 1–29 and 32–37; switch item 37 itself includes terminal item 38. Heater item 39 is separately listed, outside the stated complete-carburetor inclusion ranges. Do not assume the heater is supplied with the carburetor.

Source: TI 3/1996, p. 1 · TI 3/1996, p. 2 · TI 3/1996, p. 3 · TI 3/1996, p. 4 — Section 2, summary and complete-carburetor inclusion rows.

Part numbers (5)
  • 1128 120 0618 — C3M-S24Original complete carburetor · 044 Arctic
  • 1128 120 0616 — C3M-S23Earlier carburetor-heating-only configuration · Up to X 30 991 111
  • 1128 120 0620 — HD-11Conditional replacement · 044 Arctic; actual heater configuration matters
  • 1128 434 5101 — Separate heating elementRequired S23 conversion companion · Not included by the complete-carburetor item ranges
  • 1128 430 0501 — Thermostatic switchHD-11 distinguishing part · Includes terminal item 38

Historical fitment · 044

044 Arctic: HD-11 harness conversion dependencies

The S23-to-HD-11 conversion requires a new terminal, insulating tube and separate heater; the referenced crimping detail remains unavailable.

  • For the earlier C3M-S23 carburetor-heating-only configuration up to X 30 991 111, the printed sequence is: disconnect thermostatic switch/wiring harness; pull the tab receptacle off the heater; remove the carburetor; cut off the tab receptacle; slip insulating tube 1121 442 0402 over the wire.
  • Use crimping tool 5910 890 8210 to attach terminal socket 1118 431 6700. Proper crimping is delegated to TI47/1992 page 5, absent from the retained 690-TI inventory. No missing die selection, strip length, crimp dimension or pull-test value is invented. This note is not a complete executable repair procedure.
  • Install the new carburetor and heater 1128 434 5101 with TI07/1995 as the heater reference. Connect switch and heater to the harness, slip the tube over the connector and position wires as in TI07/1995 chapter 6. The page 2 drawing shows the connector/heater arrangement; it supplies no connector pinout.
  • TI07/1995 routing is retained and separately reviewed. Its printed tube is 1121 442 0400, whereas this conversion explicitly specifies 1121 442 0402. These are source-specific numbers, not an established alias or blanket tube supersession.
  • Page 2 calls 1118 431 6700 a terminal socket; page 4 item 38 calls the same number a terminal pin and includes it in switch item 37. Preserve both labels; do not infer connector gender or an additional unlisted mating part.

Source: TI 3/1996, p. 1 · TI 3/1996, p. 2 · TI 3/1996, p. 4 — Section 2 service note and page 2 full conversion sequence; items 37–39.

Part numbers (4)
  • 1121 442 0402 — Insulating tubeHarness conversion companion · Earlier S23 to HD-11 conversion
  • 5910 890 8210 — Crimping toolSpecified service tool · Detailed crimp procedure missing
  • 1118 431 6700 — Terminal socket / terminal pin, source labelsHarness conversion terminal · Also item 38 included in switch item 37
  • 1128 434 5101 — Heating elementSeparate conversion companion · Earlier S23 to HD-11 conversion

Wrong number or missing part for the 044? Report a correction →