Stihl 1128 · Section N · 13 of 16 · 22 parts
Shroud, Air filter
Fits 046.
Historical fitment & changes (11) — includes parts and conditions not shown on this drawing.
Parts (22)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1128 080 1616 | Shroud | 1 |
| 2 | 1121 084 7100 | Cap | 1 |
| 3 | 1128 084 8301 | Reflector foil | 1 |
| 4 | 0000 963 0808 | Bushing | 3 |
| 5 | 1128 967 1506 | Model plate 046 | 1 |
| 6 | 1122 084 7100 | Cap | 1 |
| 7 | 9022 341 0980 | Spline screw IS-M5x16 | 3 |
| 8 | 1128 120 3404 | Filter base Fitment / change note → → replaced by 1128 120 3406 TI 44/2000 | 1 |
| 8 | 1128 120 3406 | Filter base Fitment / change note → → replaced by 1128 120 3404 TI 32/2002 | 1 |
| 9 | 1128 120 2202 | Flange | 1 |
| 10 | 9121 319 0960 | Stud M5x12x9 | 1 |
| 11 | 9216 263 0700 | Hexagon nut M5 → replaced by 9220 260 0701 TI 25/1994 | 2 |
| 12 | 1128 121 6900 | Baffle | 1 |
| 13 | 1128 141 6300 | Air baffle | 1 |
| 14 | 0000 120 1653 | Air filter, wire mesh | 1 |
| 15 | 1128 140 1001 | Filter cover Fitment / change note → | 1 |
| 16 | 1128 141 4001 | Slide | 1 |
| 17 | 1124 140 9500 | Twist lock Fitment / change note → | 1 |
| 18 | 0000 140 4402 | Air filter HD2 | 1 |
| 19 | 0000 141 0300 | Prefilter Fitment / change note → | 1 |
| 20 | 0000 967 1593 | Model plate Magnum | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 1128 967 1503 | Model plate 046 C not illustrated | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
IPL correction · 044 / 046
046 IPL correction: wrong filter base listed
The September 1995 046 IPL, page 25, illustration L, position 7 incorrectly listed the 044 filter base 1128 124 3408. TI 05/1996 specifies 1128 124 3404 for the 046.
- 1128 124 3408 belongs to the 044 in this correction; its erroneous appearance in that 046 IPL is not evidence of 046 fitment.
- TI 05/1996 prints 1128 124 3404 for that 046 configuration. This is a historical source statement, not a current ordering recommendation. The historical L/7 locator is not a position on this later drawing.
- Later TI 44/2000 and the retained 046 IPL use 1128 120 3404 instead. The 124 versus 120 discrepancy is unresolved; do not silently equate these numbers.
Source: TI 5/1996, p. 2 — Section 3: Air filter (correction to 046 parts list).
Part numbers (2)
- 1128 124 3408 — Filter baseErroneous 046 listing / documented 044 part · 044; not the 046 base specified by this correction
- 1128 124 3404 — Filter baseCorrected part · 046 configuration in the September 1995 IPL correction
Historical fitment · 046
046: unchanged cover number, different setting marks
Filter cover 1128 140 1001 retains its number while production setting symbols change.
- The replacement cover supplied without setting symbols is documented for original and new machine versions.
- Part number 1128 140 1001 does not identify which setting marks a cover carries. Follow the installed carburetor specification, not an assumed cover revision.
- The changed standard-production symbols are H = 3/4 and L = 1/4; these settings are measured from the lean stop in the capped-carburetor instruction, not from screw seats.
- Introduction is from the start of EPA-version production. Unmodified covers continue to be supplied until existing factory stocks are exhausted; this does not make the same part number a revision identifier.
Source: TI 47/1997, p. 3 · TI 47/1997, p. 6 — Section 3 and summary: 046 cover markings; full section, drawing and summary context reviewed in batch26.
Part numbers (1)
- 1128 140 1001 — Filter coverSame number, different markings · 046 original/new versions; symbol-free replacement
Conditional replacement · 046
046: filter-base revision, with unresolved earlier number
TI 44/2000 prints 1128 120 3404 → 1128 120 3406; an earlier TI prints a different middle group.
- TI 44/2000 describes additional intake openings and prints old base 1128 120 3404 and new base 1128 120 3406. These numbers also appear in the retained 046 IPL.
- TI 05/1996 instead prints 1128 124 3404 in its IPL correction. The 120 versus 124 discrepancy is unresolved; do not assume an alias, typo correction or supersession between those two numbers.
- The 2000 introduction table distinguishes 046 flush handle (1 46 085 314) and wrap handle (1 46 086 124). This is not evidence of 044 fitment.
- Drawing 145TI051 SC labels 1 as the previous filter base and 2 as the new version; the arrow identifies additional openings for increased intake airflow. These local drawing labels are not summary item numbers. No hole dimensions or modification procedure for the old base are supplied.
- Summary item 5 carries remark 1: the previous base is no longer available from the factory at the time of this TI. This does not establish current stock or resolve the earlier 120-versus-124 middle-group conflict.
- The general engine-uprating introduction mentions a filter base, but section 1.3 explicitly says 046 only. Do not extend this part revision to 044 or infer a piston/cylinder prerequisite that the filter-base section does not state.
Source: TI 44/2000, p. 1 · TI 44/2000, p. 2 — Complete sections 1–2: uprated engine, piston/cylinder service direction, 046 filter base, all summary rows and handle-specific cutoffs.
Part numbers (2)
- 1128 120 3404 — Filter basePrevious number printed in TI 44/2000 · 046; not silently aliased to 1128 124 3404
- 1128 120 3406 — Filter baseNew number printed in TI 44/2000 · 046 revised intake openings
Historical fitment · 046
046: supplied HD-filter foam insert is not required
HD filter assembly 0000 120 1650 includes foam element 1124 124 0804 for other models; the 046 does not require it.
Later reviewed guidance: 046 / 088: dry HD filter without inner foam
- The source explicitly says foam element 1124 124 0804 is necessary for this HD filter on 044, 066 and 084, but is not required on 046. Its presence in the package does not establish that it must be fitted to 046.
- The foam stays in the scope of supply for interchangeability. A separate instruction sheet describes model-specific use; that sheet remains an unverified dependency, not a reconstructed installation procedure.
- TI20/1995, TI10/1995 and TI18/1995 are cited for the earlier 044, 066 and 084 introductions. This note is bound only to the exact 046 filter sheet and does not automatically expand later MS-model applicability or overwrite those models’ own instructions.
Source: TI 46/1995, p. 10 — Section 5.1.3: complete HD-filter assembly and foam exception.
Part numbers (2)
- 0000 120 1650 — HD filter assemblyShared supply assembly · 046 foam exception; no universal installation rule
- 1124 124 0804 — Foam elementSupplied but not required on 046 · Required on 044/066/084 per source comparison
Service note · 046
046: oil the HD fabric, keep the felt prefilter dry
The 1995 HD fabric requires filter oil before first use; winter operation calls for the green mesh element.
- The black HD element is intended for dry, very dusty sites. Its fabric must be impregnated with STIHL HD filter oil before first use; the source warns that dry fabric filters poorly. The separate felt prefilter is described as dry. Do not transfer the fabric-oiling requirement to the felt prefilter.
- The source supplies a 100 ml (3.5 fl.oz) oil bottle, not a dose to pour into each filter. It gives no complete washing, drying or re-oiling procedure.
- Use the green wire-mesh element for snow and winter conditions; replacing the HD element avoids icing. Remove the carburetor-box cover, exchange the element and refit the cover without tools. Tightening the cover screw brings cover, filter and base together; peripheral filter lips provide the dirt seal.
- Cleaning is called for when power noticeably declines. The compensator means increasing filter contamination does not itself require changing the high-speed screw setting. This is not an instruction to compensate for an engine fault by ignoring adjustment or maintenance.
- Detailed compensator explanation refers to TI 07/1991 (066), absent from the retained TI inventory. These 1995 instructions do not establish oiling requirements for later HD2 filters.
Source: TI 46/1995, p. 2 · TI 46/1995, p. 3 — 1.1–1.2: filter selection, sealing and compensator.
No additional parts-table entry added.
Historical fitment · 046
046: decompression valve and dust cover arrangement
Cover 1122 084 1405 sits between cylinder and shroud; the raised shroud opening protects the valve.
- The valve body carries an axially moving conical plunger retained in either position by three spring-loaded balls. Pushing it down opens the passage for starting; ignition pressure raises the plunger and closes the passage.
- The starting description is distinct from the closed-valve prerequisite for the locking strip. No valve opening pressure or valve part number is given here.
- The shroud opening is raised to reduce accidental contact. The separate cover limits dirt entry; sharing this cover number does not establish cylinder or shroud interchangeability.
Source: TI 46/1995, p. 4 — 1.6: construction, operation and cover.
Part numbers (1)
- 1122 084 1405 — Cover between cylinder and shroudDust-entry protection · 046 decompression opening
Service note · 046
046: original engine dimensions and construction
The 1995 046 specification is 76.5 cm³, 52 mm bore and 36 mm stroke; it is not a 044 interchange claim.
- Compared with 044, the bulletin describes a wider big-end bearing, stronger crankcase, revised intake flange/baffle, cylinder cooling area increased by 10%, modified shroud/outlet plate and redesigned vibration buffers. No replacement numbers or retrofit permission are given.
- The composite flywheel uses a steel hub, polymer fan, high-power magnets and magnesium starter-pawl bushing. Claimed weight reduction is about 30%, with cooling-air flow increased by 30%; these are source comparisons, not measurements made by this project.
- The cylinder/crankcase uses 6 mm mounting screws and a sheet-steel gasket. The engine is a single-cylinder two-stroke with specially impregnated bore; compression ratio 9.6: 1. Three-part drop-forged crankshaft, two deep-groove main bearings, needle-cage big and small ends, 62 mm connecting rod and 12 mm piston pin are specified.
- Rated power is 4.4 kW (5.9 bhp) at 9,500 rpm; maximum torque is 4.8 Nm (3.54 lb.ft) at 6,500 rpm. Maximum permissible speed is 13,500 rpm WITH Rollomatic bar and chain, not an unloaded powerhead test limit. Mean idle is 2,500 rpm.
- The unlined centrifugal clutch is 76 mm diameter and engages at approximately 3,500 rpm. The ElastoStart rewind mechanism uses pawl engagement and 3.5 mm starter rope.
- Powerhead weight excluding cutting attachment is 6.5 kg (14.3 lb). The page separately prints power-to-weight ratio 2.55 lbs/bhp; this does not agree with the printed 14.3 lb and 5.9 bhp (about 2.42). Preserve the discrepancy, not a silently recalculated replacement.
- Specifications describe this historical 046 release; they do not identify all later 046/MS 460 variants or establish interchangeable engine, flywheel or AV parts.
Source: TI 46/1995, p. 1 · TI 46/1995, p. 3 · TI 46/1995, p. 5 · TI 46/1995, p. 6 · TI 46/1995, p. 7 — 1.3–1.5,1.8–1.9,1.11,2.1,2.4: original construction and specifications.
No additional parts-table entry added.
Service note · 046
046: engine fasteners and catalytic-muffler torque branches
Cylinder, crankcase, flywheel, clutch and muffler values retain thread and variant distinctions.
- These are historical TI 46/1995 page 11 fastener-specific values, not universal torque by thread diameter. No fastener part number is supplied. Printed lbf.ft equivalents are retained alongside Nm.
- Cylinder/crankcase IS-M6×25: 15 Nm (11 lbf.ft); crankcase IS-M5×20: 11.5 Nm (8.5 lbf.ft); shroud/crankcase IS-M5×16: 7 Nm (5.2 lbf.ft).
- Standard muffler top IS-M5×6: 6.5 Nm (4.8 lbf.ft), Loctite 242; muffler/cylinder IS-M5×16: 11.5 Nm (8.5 lbf.ft), Loctite 242.
- Kat/catalytic muffler top IS-M5×30: 6.5 Nm (4.8 lbf.ft), Loctite 242; Kat muffler/cylinder IS-M6×18: 15 Nm (11 lbf.ft), Loctite 242. Separate muffler/crankcase IS-M6×18 row: 15 Nm (11 lbf.ft), with no adhesive remark printed.
- Flywheel M8×1 nut: 32.5 Nm (24 lbf.ft); clutch M12×1 L carrier: 50 Nm (37 lbf.ft), with left-hand thread explicitly marked L.
- Cylinder decompression valve M10×1: 14 Nm (10.3 lbf.ft), not the leakage-test plug; spark plug M14×1.25: 25 Nm (18.5 lbf.ft).
Source: TI 46/1995, p. 11 — 5.3: engine, exhaust and rotating assembly rows.
No additional parts-table entry added.
Service note · 046
046: small-fastener torques, adhesives and ignition washer
The ignition-module screws require both Loctite 242 and a washer; nearby screws have different requirements.
- These are historical TI 46/1995 page 11 fastener-specific values, not universal torque by thread diameter. No fastener part number is supplied. Printed lbf.ft equivalents are retained alongside Nm.
- Generator IS-M4×12: 3.5 Nm (2.6 lbf.ft), Loctite 649. Chain-tensioner cover plate IS-M4×8: 3 Nm (2.2 lbf.ft).
- IS-M4×12 oil-pump cover at sprocket side: 3 Nm (2.2 lbf.ft); brake-band/crankcase: 3 Nm (2.2 lbf.ft), Loctite 242; oil pump: 3.5 Nm (2.6 lbf.ft).
- IS-M4×12 segment/fan housing: 2.5 Nm (1.8 lbf.ft); sprocket-side crankcase cover: 3 Nm (2.2 lbf.ft).
- M5 SK6 collar nut for carburetor/filter base/flange: 6 Nm (4.4 lbf.ft), remark 3/Loctite 270. The table calls the fastener a collar nut although its remark generically says screw; neither label is silently changed.
- Fan housing IS-M5×20: 7 Nm (5.2 lbf.ft). Ignition module/crankcase IS-M5×20: 7 Nm (5.2 lbf.ft), Loctite 242 AND a washer under the screw head. Do not transfer this washer requirement to every M5 screw.
Source: TI 46/1995, p. 11 — 5.3: M4 rows, intake collar nut, fan housing and ignition.
No additional parts-table entry added.
Historical fitment · 046 / 088
046 / 088: dry HD filter without inner foam
Dry fleece replacement, cleaning and model-specific foam rule.
- Dry fleece HD filter 0000 120 1652 replaces oil-impregnated HD filter 0000 120 1650. The new filter carries the crossed-out OIL pictogram and does not need oil impregnation. This is not a blanket no-oil rule for the original filter or unrelated filter materials.
- When cutting power noticeably drops, clean felt prefilter 0000 141 0300. After several prefilter cleanings, or if power remains low with a clean prefilter, remove the felt prefilter and clean the HD filter; carefully blow from the clean-air side if possible. On 044/064/066/084 also remove inner foam 0000 124 0800 for cleaning.
- For stubborn dirt or caked fleece, wash filter parts in a clean non-flammable solution, such as warm soapy water. No air-pressure value, solvent recipe, drying duration or oiling step is supplied by this bulletin.
- Fine trapped dirt may remain after cleaning and shorten cleaning intervals with extended use. Replace the filter when those intervals are no longer practical, or if thorough cleaning after long operation still leaves a noticeable cutting-power loss. No fixed service-hour limit or diagnosis excluding other causes is established.
- Introduction is in progress, without a numeric cutoff. Original filter 0000 120 1650 was no longer supplied by the factory in this historical source, not a present stock assertion. An included instruction sheet is mentioned but is not reproduced or claimed reviewed here; the printed bulletin procedures above stand on their own.
- Inner foam element 0000 124 0800 is included in the supplied HD filter but must be removed before installation in the new STIHL HD system, explicitly identified here as 046 and 088. Inclusion is not positive foam fitment. The 088 application is stated on page2 even though it is absent from the page1 model heading.
- No later MS-model, every air-filter system or physical interchange claim is inferred from the shared part number.
Source: TI 43/1996, p. 1 · TI 43/1996, p. 2 — Both complete pages: dry fleece identification, cleaning, service life, installation and supply summary.
Part numbers (4)
- 0000 120 1650 — Oil-impregnated HD air filterOriginal · 046 / 088
- 0000 120 1652 — Dry fleece HD air filterReplacement · 046 / 088
- 0000 141 0300 — Felt prefilterCleaning subject · 046 / 088
- 0000 124 0800 — Inner foam elementRemove before installation · 046 / 088
Conditional replacement · 046 / MS 460
046 / MS 460: fine-dust filter kit and START-STOP label
Retain the installation label and the summary’s missing item 6 without inventing an order number.
- Fine-dust filter assembly 0000 120 1655 is a special accessory for 046 and MS 460, intended to improve filtration in very dusty work areas. It is not announced as a universal replacement for all filters or assigned a serial cutoff.
- Remove the existing filter cover and air filter. Fit prefilter 0000 141 0600 over air filter 0000 120 1601. Press twist lock 1124 140 9500 into retaining plate 0000 124 1000. Fit the filter/prefilter, then the retaining plate with twist lock and tighten firmly. No numerical tightening torque is given.
- Stick the adhesive START-STOP label on the tank housing at the arrowed position in the page 2 drawing. Diagram callout 5 is this label, whereas summary item 5 is the retaining plate; the diagram and summary numberings are not interchangeable.
- Unresolved source omission: summary item 1 says the assembly includes items 2 to 6, but the printed table ends at item 5 and supplies no label row or unambiguous label order number. The extracted text includes the fragment “000 967 4955 A XX”, but the retained scan does not establish a complete four-digit-prefix label order number. That fragment is not admitted as a separately orderable part. Do not fabricate item 6, drop the label instruction or claim complete current kit contents.
- Last-TI references 16/2002 and 05/2001 are bibliographic pointers, not required external installation steps. The printed two-page instruction is fully reviewed with its internal table omission explicitly retained.
- The named model scope is not extended to other models sharing series 1128 or later IPL sheets. Factory supply statements are historical, not current stock. No physical interchange test was performed.
Source: TI 39/2002, p. 1 · TI 39/2002, p. 2 — Entire TI 39/2002: installation drawings, label and summary.
Part numbers (5)
- 0000 120 1655 — Fine-dust filter assemblySpecial accessory · Only the named model and configuration; see conditions
- 0000 141 0600 — PrefilterFits over filter · Only the named model and configuration; see conditions
- 0000 120 1601 — Air filterInner filter · Only the named model and configuration; see conditions
- 1124 140 9500 — Twist lockRetaining-plate fastener · Only the named model and configuration; see conditions
- 0000 124 1000 — Retaining plateIncludes fitted twist lock · Only the named model and configuration; see conditions
Wrong number or missing part for the 046? Report a correction →