Stihl 1128 · Section J · 9 of 13 · 45 parts
Carburetor HD-15C, HD-17C
Fits MS 440.
Historical fitment & changes (9) — includes parts and conditions not shown on this drawing.
Parts (45)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4116 121 5100 | Inlet needle | 1 |
| 2 | 4116 121 5000 | Inlet control lever | 1 |
| 3 | 1128 122 3002 | Spring | 1 |
| 4 | 1113 121 9200 | Spindle | 1 |
| 5 | 1114 122 7400 | Round head screw | 1 |
| 6 | 4117 122 9402 | Plug | 1 |
| 7 | 1128 121 5405 | Valve jet | 1 |
| 8 | 1128 121 5602 | Fixed jet 0.70 → replaced by 1128 121 5603 TI 47/1997 | 1 |
| 9 | 1128 121 5605 | Fixed jet 0.66 | 1 |
| 10 | 1128 129 0906 | Gasket | 1 |
| 11 | 4116 121 4700 | Metering diaphragm | 1 |
| 12 | 1128 121 0801 | End cover | 1 |
| 13 | 1121 122 7101 | Screw | 4 |
| 14 | 1114 121 7800 | Strainer | 1 |
| 15 | 4116 121 4800 | Pump diaphragm | 1 |
| 16 | 4116 129 0902 | Gasket | 1 |
| 17 | 1127 122 3205 | Torsion spring | 1 |
| 18 | 1127 120 7100 | Throttle shaft with lever | 1 |
| 19 | 1117 122 9000 | E-clip | 1 |
| 20 | 1128 121 3302 | Throttle shutter | 1 |
| 21 | 1115 122 7400 | Round head screw | 1 |
| 22 | 1127 122 3200 | Torsion spring | 1 |
| 23 | 1127 120 7200 | Choke shaft with lever | 1 |
| 24 | 1123 122 9000 | E-clip | 1 |
| 25 | 1122 121 2900 | Choke shutter | 1 |
| 26 | 1110 122 7400 | Round head screw | 1 |
| 27 | 1127 122 6200 | Idle speed adjustment screw | 1 |
| 28 | 1127 121 0800 | End cover | 1 |
| 29 | 1114 122 7100 | Screw | 1 |
| 31 | 1127 122 6701 | High speed adjustment screw | 1 |
| 32 | 1128 122 6807 | Low speed adjustment screw | 1 |
| 33 | 1128 122 6703 | High speed adjustment screw | 1 |
| 34 | 1128 122 6806 | Low speed adjustment screw | 1 |
| 35 | 4203 122 3600 | Sealing ring | 1 |
| 36 | 4203 121 2700 | Cap Fitment / change note → | 2 |
| 37 | 1128 129 1100 | Gasket | 1 |
| 38 | 1128 430 6002 | Heating element | 1 |
| 39 | 1118 431 6600 NLA | Terminal pin no longer available from factory | 1 |
| 40 | 1118 431 6700 NLA | Terminal socket no longer available from factory | 1 |
| 41 | 1124 121 9100 | Bushing | 1 |
| 42 | 1128 121 5605 | Fixed jet 0.66 option | 1 |
| 43 | 1122 121 5604 | Fixed jet 0.64 option | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 1128 120 0625 | Carburetor HD-15C Fitment / change note → → replaced by 1128 120 0622 TI 39/2003 | 1 |
| — | 1128 120 0622 | Carburetor HD-17C Fitment / change note → | 1 |
| — | 1128 007 1066 | Set of carburetor parts option | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Conditional replacement · MS 440 / MS 460
MS 440 / MS 460: revised limiter cap keeps the same number
Limiter cap 4203 121 2700 and the carburetor retain their part numbers despite revised cap/segment geometry; number alone does not identify the old or new cap.
Later reviewed guidance: MS 440 / MS 460: square-bit driver for fitted limiter caps
- Limiter cap 4203 121 2700 and the carburetor retain their part numbers despite revised cap/segment geometry; number alone does not identify the old or new cap.
- The new cap has no upper detent, adds an alignment mark and moves the lug from perpendicular to the screw slot into line with it.
- MS 440 and MS 460 are in the source’s marked-segment list. The L cap must not simply be pulled off at its stop: the source requires quarter-turn offset and alignment of slot, groove, visible lug and marks.
- H and L removal have separate alignment instructions. Puller 5910 890 4500 has a left-hand engagement thread; this note is not a complete carburetor removal or calibration procedure.
- Removed limiter caps must not be reused because removal damages them. Replace caps after screw replacement or carburetor cleaning; no permanent cap-removal modification is implied.
- Other models appear on the bulletin cover, but this record is scoped to the two verified MS 440/MS 460 carburetor sheets. Do not extend the marked-segment instructions solely from the cover list.
- Retained edition: English USA. Introduction is continuous, with no numeric serial cutoff. Historical availability is not current stock or universal regional applicability.
Source: TI 21/2005, p. 1 · TI 21/2005, p. 2 · TI 21/2005, p. 3 · TI 21/2005, p. 4 — Sections 1–5: cap/segment revision, exact model list, removal and unchanged number.
Part numbers (2)
- 4203 121 2700 — Limiter capUnchanged number, revised geometry · MS 440/MS 460 capped-carburetor configuration; single-use after removal
- 5910 890 4500 — Limiter-cap pullerService tool · Left-hand engagement; separate H/L alignment
Conditional replacement · MS 440 / MS 460
MS 440 / MS 460: square-bit driver for fitted limiter caps
Screwdriver 5910 890 2304 is specified for carburetors using limiter cap 4203 121 2700; its square bit reaches the adjusting screw through the fitted cap.
- Screwdriver 5910 890 2304 is specified for carburetors using limiter cap 4203 121 2700; its square bit reaches the adjusting screw through the fitted cap.
- This sheet association is conditional on that exact cap configuration, not every carburetor fitted to these saws.
- The source distinguishes initial engagement at the first detent from final fully-home seating after the series-specific basic setting. Do not treat the first detent as the completed installation.
- Required idle/high-speed settings depend on the exact series; this bulletin supplies no universal screw-turn or RPM setting. Later series-specific service guidance still governs.
- Caps removed to service an adjusting screw or clean the carburetor must not be reused. TI 21/2005 supplies the removal dependency; this is not authorization for permanent limiter removal.
- Retained edition: English USA. Introduction is continuous, with no numeric serial cutoff. Historical availability is not current stock or universal regional applicability.
Source: TI 50/2006, p. 3 · TI 50/2006, p. 4 · TI 50/2006, p. 5 — Sections 3–3.4 and summary: capped-carburetor service tool and seating stages.
Part numbers (2)
- 5910 890 2304 — Square-bit carburetor screwdriverService tool · Carburetors using 4203 121 2700 fitted caps
- 4203 121 2700 — Limiter capExact tool configuration · New caps; final seating after series-specific basic setting
Service note · MS 440
MS 440 carburetor change: HD-15B to capped HD-17A
The old carburetor remains available; later C-suffix catalog names are not the 2003 names.
- TI39/2003 replaces uncapped carburetor 1128 120 0625 with capped 1128 120 0622. Its summary calls them HD-15B and HD-17A respectively. The new assembly includes limiter cap 4203 121 2700 (summary item 3). The previous 0625 remains available for older machines and other models; no unnamed model applications are inferred.
- Introduction is CONTINUOUS with NO numeric serial cutoff. Spare parts for the new carburetor are referred to the current parts documentation; this bulletin does not supply a complete carburetor rebuild-parts list. Its historical availability statement is not a present stock check.
- The local SCS 01-2012 USA sheet names the same order numbers HD-15C and HD-17C. Preserve this edition/variant naming difference: association to that MS 440 sheet provides a navigation anchor, not proof that B/A and C/C calibrations or every internal part are identical. This note does not rename the canonical catalog rows.
- The introductory European-emissions claim is the vendor’s historical rationale, not an independently verified current compliance certification. The bibliography identifies TI28/2002 as the preceding MS 440 bulletin; its review remains separate.
- Historical TI39/2003 English guidance for the specified MS 440 carburetor or muffler configuration; not a universal setting for every MS 440 revision or region. MS 440 C catalytic-converter conditions apply only where explicitly stated. No physical interchange test was performed.
Source: TI 39/2003, p. 1 · TI 39/2003, p. 5 — 1/1.1 and complete summary including remarks.
Part numbers (3)
- 1128 120 0625 — Carburetor HD-15B in TI39/2003Previous uncapped assembly; retained supply · MS 440; exact historical configuration stated above
- 1128 120 0622 — Carburetor HD-17A in TI39/2003New capped assembly; includes item 3 · MS 440; exact historical configuration stated above
- 4203 121 2700 — Limiter capIncluded in new carburetor summary item 2 · MS 440; exact historical configuration stated above
Service note · MS 440
MS 440 limiter removal: align each ridge before using the extractor
H and L use different starting positions; avoid twisting a ridge out of its groove.
- The new carburetor limits user adjustment of both H and L to a printed 258° (approximately 3/4 turn). Preserve the exact 258° and the source’s approximation; do not silently replace it with 270°. Caps fit the knurled screw heads, while stops on the carburetor housing limit travel. Drawing items are caps (1), H screw with seal (2), L screw with seal (3) and idle-speed screw (4).
- Caps must be removed to replace a defective adjusting screw or clean the carburetor. Turn H ANTICLOCKWISE to its stop so its cap ridge aligns with the housing groove. Turn L CLOCKWISE to its stop, then BACK OFF 1/4 TURN so its ridge aligns with its housing groove. The L-cap ridge is perpendicular to the screw slot.
- Turn extractor 5910 890 4500 ANTICLOCKWISE until the cap is pulled off the adjusting-screw head. The cap may twist as the extractor is turned in: recheck RIDGE-TO-GROOVE ALIGNMENT as it is pulled off. This direction is stated explicitly, not assumed from ordinary screw extraction.
- Before adjustment after maintenance/repair, check the air filter and spark-arresting screen IF FITTED; clean or replace as necessary. Removed limiter caps MUST NOT BE REUSED. Follow the basic-setting and NEW-cap seating notes; this is not a permanent limiter-removal procedure.
- Historical TI39/2003 English guidance for the specified MS 440 carburetor or muffler configuration; not a universal setting for every MS 440 revision or region. MS 440 C catalytic-converter conditions apply only where explicitly stated. No physical interchange test was performed.
Source: TI 39/2003, p. 2 · TI 39/2003, p. 3 · TI 39/2003, p. 5 — 1.3/1.3.1/1.3.2 complete.
Part numbers (2)
- 5910 890 4500 — Limiter-cap extractorAnticlockwise extraction with ridge alignment · MS 440; exact historical configuration stated above
- 4203 121 2700 — Limiter capReplace after removal · MS 440; exact historical configuration stated above
Service note · MS 440
MS 440 basic turns: catalytic MS 440 C needs H at 7/8
Do not apply the extra 1/8-turn correction twice.
- With limiter caps removed for service, the bulletin starts from the seated (“tight”) adjusting-screw position. On MS 440, back H out 1 TURN and L out 1 TURN. On MS 440 C WITH CATALYTIC CONVERTER, back H out 7/8 TURN and L out 1 TURN. Do not treat every C-labelled machine as proof of a catalytic converter.
- Section 1.2 requires H to be 1/8 turn CLOCKWISE (leaner) when a replacement 1128 120 0622 is serviced into the catalytic MS 440 C. Section 1.3.3’s 7/8-turn H baseline already expresses that difference from the ordinary one-turn baseline; it is not an instruction to subtract ANOTHER 1/8 from 7/8.
- Setting disk 5910 893 6600 is the specified aid. These are uncapped BASIC starting positions, not the capped standard-setting stops and not a substitute for the separate measured-speed sequence. Check air filter and any fitted spark screen before adjustment; finish with NEW caps.
- Historical TI39/2003 English guidance for the specified MS 440 carburetor or muffler configuration; not a universal setting for every MS 440 revision or region. MS 440 C catalytic-converter conditions apply only where explicitly stated. No physical interchange test was performed.
Source: TI 39/2003, p. 1 · TI 39/2003, p. 2 · TI 39/2003, p. 3 — 1.2 and 1.3.3 initial basic settings without caps.
Part numbers (2)
- 1128 120 0622 — Capped replacement carburetorCatalytic MS 440 C H-setting exception · MS 440; exact historical configuration stated above
- 5910 893 6600 — Carburetor setting diskAid for uncapped basic turns · MS 440; exact historical configuration stated above
Service note · MS 440
MS 440 service adjustment: 3300, peak check, 2500 and 13500 rpm
The peak-over-3700 restart rule is not the final idle setting.
- After filter/screen checks and the model-specific uncapped starting turns, the source specifies a ±200 rpm tolerance for its set speeds. Step 1: use LA to set 3300 rpm. Step 2: turn L clockwise or anticlockwise to find the HIGHEST speed. If that peak is GREATER THAN 3700 rpm, STOP AND RESTART AT STEP 1.
- Step 3: use LA to return to 3300 rpm. Step 4: use L to set 2500 rpm. Step 5: use H to set the maximum speed of 13,500 rpm. Preserve the screw/step mapping: the 3300 intermediate steps and 3700 restart threshold are not a final idle target. Do not invent an extra ±200 allowance on the explicitly greater-than-3700 restart rule.
- The source warns that an overly lean setting can damage the engine through overheating and shortage of lubricant. Step 6 proceeds to section 1.3.4 to secure NEW limiter caps. This is historical operating-procedure documentation, not evidence that an engine was run or that a setting was physically verified.
- Historical TI39/2003 English guidance for the specified MS 440 carburetor or muffler configuration; not a universal setting for every MS 440 revision or region. MS 440 C catalytic-converter conditions apply only where explicitly stated. No physical interchange test was performed.
Source: TI 39/2003, p. 2 · TI 39/2003, p. 3 — 1.3.3 complete measured-speed sequence and cautions.
No additional parts-table entry added.
Service note · MS 440
MS 440 limiter refit: new caps, correct ridges and flush seating
The 2003 procedure requires final seating, not reused caps or a permanent open adjustment.
- Limiter caps MUST NOT BE REUSED. Insert new caps 4203 121 2700 into the holes with ridges oriented as the arrows show in section 1.3.4, then press them onto the adjusting screws until FLUSH WITH THE CARBURETOR HOUSING (1). Do not infer orientation merely from the screw-slot angle; use the cap ridges and illustrated housing grooves.
- This follows completed basic adjustment, not the standard-setting procedure with caps left on. The later, separately reviewed TI50/2006 note describes a square-bit tool and first-detent versus fully-home seating for its exact cap configuration. This 2003 flush-seating instruction is retained as historical source context, not a claim that the later first detent is a finished installation.
- Historical TI39/2003 English guidance for the specified MS 440 carburetor or muffler configuration; not a universal setting for every MS 440 revision or region. MS 440 C catalytic-converter conditions apply only where explicitly stated. No physical interchange test was performed.
Source: TI 39/2003, p. 3 · TI 39/2003, p. 5 — 1.3.4 and summary cap identity.
Part numbers (1)
- 4203 121 2700 — Limiter capNew caps only; final flush seating · MS 440; exact historical configuration stated above
Service note · MS 440
MS 440 capped standard setting: H to stop, L back 1/4
Mountain adjustment remains bounded by the cap stop and lean-running warning.
- DO NOT REMOVE THE LIMITER CAPS for the standard setting. Switch OFF the engine, check the air filter and any fitted muffler spark-arresting screen, and clean or replace as required. Turn H ANTICLOCKWISE as far as possible (printed maximum 3/4 turn). Turn L CLOCKWISE as far as possible, then BACK OFF 1/4 TURN.
- This capped standard setting is not the uncapped one-turn/7/8-turn basic setting. Preserve the distinction between a stop-limited range and a measured turn from a seated screw.
- If operation in mountain country is unsatisfactory, check the standard setting, let the engine warm up, then turn H CLOCKWISE (leaner), only as far as the stop. The source permits a marginal adjustment; it provides no altitude-to-turn table. Too lean can cause overheating and inadequate lubrication. No removal or bypass of the cap stop is instructed.
- Historical TI39/2003 English guidance for the specified MS 440 carburetor or muffler configuration; not a universal setting for every MS 440 revision or region. MS 440 C catalytic-converter conditions apply only where explicitly stated. No physical interchange test was performed.
Source: TI 39/2003, p. 3 · TI 39/2003, p. 4 — 1.3.5 standard setting and mountain-country adjustment.
No additional parts-table entry added.
Service note · MS 440
MS 440 idle adjustment: separate stalling, moving-chain and lean-idle cases
After changing L, revisit LA; do not conflate the three symptoms.
- ENGINE STOPS AT IDLE: set L 1/4 turn open; turn LA CLOCKWISE until the chain begins to run, then back LA off 1/4 turn. The moving-chain point is a source adjustment reference, not an acceptable final idle condition.
- CHAIN RUNS AT IDLE: set L 1/4 turn open; turn LA ANTICLOCKWISE until the chain stops, then another 1/4 turn in that SAME direction. This differs from the stalling-case clockwise approach.
- UNEVEN IDLE/POOR ACCELERATION despite L 1/4 turn open: the source diagnoses an overly lean idle setting. Turn L ANTICLOCKWISE until running and acceleration are correct, no farther than the stop. Whenever L is adjusted, at least one LA adjustment is usually required. These symptom-specific instructions do not replace the capped standard setting or the separate measured-speed service sequence.
- Historical TI39/2003 English guidance for the specified MS 440 carburetor or muffler configuration; not a universal setting for every MS 440 revision or region. MS 440 C catalytic-converter conditions apply only where explicitly stated. No physical interchange test was performed.
Source: TI 39/2003, p. 4 — 1.3.5 idle-speed adjustment complete.
No additional parts-table entry added.
Wrong number or missing part for the MS 440? Report a correction →