← 064/066 · MS 660 · MS 650/640

Stihl 1122 · Section K · 10 of 14 · 23 parts

Handlebar

Fits 064.

Parts diagrams →

Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11011121314151617181922021223456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (23)

PosPart numberDescriptionQty
1 1122 120 0616 Carburetor WJ-65A → replaced by 1122 120 0621, 1122 120 0618 TI 1/1998 1
2 1124 121 9100 Bushing 1
3 1122 121 7000 NLA Baffle 1
4 9210 260 0700 Hexagon nut M5 1
5 9771 021 2620 Hose clip Ø 36x5 1
6 1122 790 1750 Handlebar 1
7 not sold separately Hose 460 mm / 18 1/8'' 1
8 9074 478 4435 Pan head self-tapping screw IS-P6x19 Fitment / change note → 2
9 9074 478 4475 Pan head self-tapping screw IS-P6x21.5 2
10 not sold separately Wrap around handlebar no longer available from factory 1
11 not sold separately Hose 265 mm / 10 7/16'' 1
12 not sold separately Hose 370 mm / 14 9/16'' 1
13 1122 791 5500 Elbow connector → replaced by 1122 790 3610, 1122 791 5501 TI 10/2008 1
14 9307 021 0120 Washer 5.3 1
15 9022 371 1020 Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 1
16 9074 478 4435 Pan head self-tapping screw IS-P6x19 Fitment / change note → 4
17 9074 478 2970 Pan head self-tapping screw IS-P4x10 1
18 1122 351 0901 Guard 1
19 9074 478 2970 Pan head self-tapping screw IS-P4x10 1
20 9074 478 4675 Pan head self-tapping screw IS-P6x32.5 Fitment / change note → 2
21 1124 791 5105 Stiffener Fitment / change note → 1
22 9022 341 1370 Spline screw IS-M6x30 1
Not numbered on the diagram — assemblies, kits and options
— 0000 791 2009 Handle hose Ø 19 mm x 5 m / 3/4x197'' option 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · 064 / 066

064 / 066: handle liner excludes wrap-around versions

Polymer stiffener fits between the handle and two longer mounting screws.

  • EXCEPT versions with wrap-around handle. Fit polymer handle liner 1124 791 5105 between the front handle and spline screws, as illustrated. Two IS-P6 x 32.5 screws 9074 478 4675 replace two IS-P6 x 19 screws 9074 478 4435 at this mounting.
  • The remark attached to the ORIGINAL short-screw row says its quantity changes from FOUR to TWO. This is not a change to only one mounting screw: the prose and both mounting-screw rows specify 2x. Do not treat MOQ H10/V50 for the new screws as installation quantities. The bulletin supplies no unrestricted retrofit or wrap-around fitment claim.
  • TI08/1994 names historical 064 and 066, series 1122, not later MS models. All six changes are in progress; no numeric serial cutoff is supplied. Publication date is January 31, 1994; 08.94 is the bulletin identifier, not an August production date. MOQ columns are commercial order quantities, not installed counts. No physical interchange test was performed.

Source: TI 8/1994, p. 2 — handle liner excludes wrap-around versions.

Part numbers (3)
  • 1124 791 5105 — Polymer handle linernew component · handle liner excludes wrap-around versions
  • 9074 478 4435 — IS-P6 x 19 spline screworiginal mounting screw; remaining quantity 2 · handle liner excludes wrap-around versions
  • 9074 478 4675 — IS-P6 x 32.5 spline screw, twonew mounting screw · handle liner excludes wrap-around versions

Service note · 064

064: standard and heated front-handle replacements

Standardization with 066 does not merge the standard and heated variants or their part numbers.

X 30 638 522 — 064 standard/heated front-handle modification only.

  • From X 30 638 522, standard front handle 1122 790 1700 becomes 1122 790 1702; heated front handle 1122 790 1710 becomes 1122 790 1712. Each new row has MOQ 1. Heated and standard versions remain distinct; do not assign the heated handle to the standard configuration.
  • The purpose is standardizing 064 parts with 066, but this is a 064 changeover, NOT a new 066 serial cutoff or proof that standard/heated versions can be substituted. Original versions remain supplied only while existing factory stocks last. No machining, wiring-conversion procedure or tightening torque is printed.
  • Historical TI 45/1994 guidance, not current stock, universal compatibility or physical verification. No hardware operation was performed.

Source: TI 45/1994, p. 2 — standard and heated front-handle replacements.

Part numbers (4)
  • 1122 790 1700 — Original standard front handlewhile stocks last · 064 only in the version/configuration described here
  • 1122 790 1702 — New standard front handleMOQ 1 · 064 only in the version/configuration described here
  • 1122 790 1710 — Original heated front handlewhile stocks last · 064 only in the version/configuration described here
  • 1122 790 1712 — New heated front handleMOQ 1 · 064 only in the version/configuration described here

Wrong number or missing part for the 064? Report a correction →