Stihl 1122 · Section A · 1 of 17 · 34 parts
Crankcase
Fits 066.
Historical fitment & changes (8) — includes parts and conditions not shown on this drawing.
Parts (34)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1122 020 2113 | Crankcase Fitment / change note → → replaced by 1122 020 2116 TI 10/2007 | 1 |
| 2 | 0000 988 5211 | Connector | 1 |
| 3 | 9371 470 2610 | Cylindrical pin 5x18 | 2 |
| 4 | 0000 974 1200 | Notched pin 2.6x8 | 1 |
| 5 | 1120 162 5200 | Pin | 1 |
| 6 | 1121 162 5205 | Pin | 1 |
| 7 | 1121 162 5200 | Pin | 2 |
| 8 | 1128 640 9100 | Valve | 1 |
| 9 | 9503 003 6676 | Grooved ball bearing 6203 | 1 |
| 10 | 9523 003 4555 | Grooved ball bearing 17x40x14 | 1 |
| 11 | 0000 953 6605 | Collar screw M8 | 2 |
| 12 | 9022 371 1020 | Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 | 6 |
| 13 | 1128 084 8302 | Reflector foil | 1 |
| 14 | 1122 021 1105 | Cover Fitment / change note → | 1 |
| 15 | 9022 313 0660 | Spline screw IS-M4x12 Fitment / change note → | 4 |
| 18 | 9640 003 1850 | Oil seal 17x32.9x3.6 | 1 |
| 19 | 9640 003 1560 | Oil seal 15x22x4 Fitment / change note → | 1 |
| 20 | 1122 029 0507 | Gasket Fitment / change note → | 1 |
| 21 | 1122 030 0408 | Crankshaft Fitment / change note → | 1 |
| 22 | 1120 036 8500 | Woodruff key 2x3.7 | 1 |
| 23 | 1122 647 9400 | Hose | 1 |
| 24 | 1117 640 3800 | Pickup body | 1 |
| 25 | 0000 350 0520 | Filler cap → replaced by 1127 350 0500 TI 48/1995 | 1 |
| 26 | 0000 359 1220 | Sealing ring | 1 |
| 27 | 0000 350 0900 | Rope | 1 |
| 28 | 0000 353 0600 | Hook | 1 |
| 29 | 1125 084 8900 | Grommet | 1 |
| 31 | 1122 021 1900 | Plug Fitment / change note → | 1 |
| 32 | 1122 020 2102 | Crankcase Fitment / change note → → replaced by 1122 020 2103 TI 2/1996 | 1 |
| 33 | 1122 030 0407 | Crankshaft Fitment / change note → → replaced by 1122 030 0408 TI 2/1996 | 1 |
| 34 | 9640 003 1355 | Oil seal 13.5x20x4 Fitment / change note → | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 1122 007 1053 | Set of gaskets Fitment / change note → | 1 |
| — | 1122 007 1054 | Set of gaskets | 1 |
| — | 1122 007 1051 | Set of gaskets | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Historical fitment · 066
066 wrap handle: matched crankshaft, crankcase and seals
The longer crankshaft and revised crankcase form a matched revision; the standard flush-cut Magnum is excluded at this date.
X 33 917 066 — Introduction of this 066 wrap-handle modification; not a model-identification range or a cutoff for the standard flush-cut version.
- From X 33 917 066, crankshaft 1122 030 0408 replaces 1122 030 0407 in the wrap-handle modification. The new shaft has a larger big-end bearing, is approximately 4 mm (0.16 in) longer, changes the taper diameter from 13.5 to 15.0 mm (0.53 to 0.6 in), and changes the ignition-end thread from M8 to M10.
- Crankcase 1122 020 2103 replaces 1122 020 2102 with increased bearing spacing, enlarged oil-seal seat and revised generator seat. Seal BS 13.5×20×4, 9640 003 1355, gives way to BS 15×22×4, 9640 003 1560. The diagrams show the distinct generator mounting seats; no unprinted dimensions are inferred.
- The bulletin expressly prohibits intermixing original and new-version parts during repairs. A replacement shaft alone is not an approved conversion. The new flywheel also requires the new crankshaft AND crankcase.
- This line modification does not yet apply to the 066 Magnum with standard flush-cut handle. Summary remark 2 says that version will change later, but supplies no later serial or date.
- Historical spare availability is retained: old crankcase for older machines; old crankshaft and seal versions for older machines and 064 under remark 3. This does not make the new 066 parts fit 064.
Source: TI 2/1996, p. 1 · TI 2/1996, p. 4 — 1.1–1.2 and summary items 1–4 / remarks 1–3.
Part numbers (6)
- 1122 030 0407 — Original crankshaftOriginal matched set · Earlier 066 wrap-handle configuration
- 1122 030 0408 — Longer crankshaftNew matched set · 066 wrap-handle revision only
- 1122 020 2102 — Original crankcaseOriginal matched set · Earlier 066 configuration
- 1122 020 2103 — Revised crankcaseNew matched set · 066 wrap-handle revision only
- 9640 003 1355 — Oil seal BS 13.5×20×4Original seal · Original seat
- 9640 003 1560 — Oil seal BS 15×22×4Revised seal · Enlarged seat
Historical fitment · 066
066 wrap handle: match flywheel and ignition module
The new red-wire module must not be mixed with the old flywheel, nor the old module with the new flywheel.
Later reviewed guidance: 066: replacement and old-stock modules require the previous 1303 configuration
X 33 917 066 — Introduction of this 066 wrap-handle modification; not a model-identification range or a cutoff for the standard flush-cut version.
- Unheated flywheel 1122 400 1214 changes to 1122 400 1217; handle-heating (VH) flywheel 1122 400 1216 changes to 1122 400 1218. The new flywheel requires the new crankshaft and crankcase; the cover and section heading restrict this engine/ignition modification to wrap-handle 066.
- The lightweight composite flywheel has a steel hub, polymer blades, magnesium starter-pawl bushing and high-performance magnets. The source reports approximately 15% weight reduction and reduced crankshaft mechanical load; these are historical design claims, not project measurements.
- Ignition module 0000 400 1303 replaces 1122 400 1311 and is identified by its red ground wire instead of black. New module with old flywheel, or old module with new flywheel, is prohibited because starting and idle-running problems can result.
- The new module air gap must be ≤0.5 mm (≤0.020 in). No lower bound or universal target setting is supplied. An incorrect gap raises the switching threshold and can prevent starting.
- Availability conflict retained: section 2.2 says the old module has been deleted; summary item 9 carries remark 1 saying the original remains available as a spare for older machines. Neither statement is silently preferred, and neither establishes present stock.
- The new module is compared with EY-V and refers to TI51/1994, which is retained but not reviewed in this batch. No additional EY-V behavior or timing curve is inferred from that reference.
Source: TI 2/1996, p. 2 · TI 2/1996, p. 4 — 2.1–2.2 and summary items 5,6,9 / remark 1.
Part numbers (6)
- 1122 400 1214 — Original unheated flywheelOriginal pairing · 066 without handle-heating flywheel
- 1122 400 1217 — Lightweight unheated flywheelNew pairing · Revised 066 wrap-handle engine set
- 1122 400 1216 — Original VH flywheelOriginal heated pairing · 066 handle heating
- 1122 400 1218 — Lightweight VH flywheelNew heated pairing · Revised engine and heater requirements
- 1122 400 1311 — Black-ground-wire ignition moduleOriginal module · Original flywheel; availability wording conflicts
- 0000 400 1303 — Red-ground-wire ignition moduleReplacement module · New flywheel only in this 066 revision
Historical fitment · 066
066: ignition fastener table retains a thread conflict
The summary labels the new nut M8×10, while the shaft text and drawing specify an M10 ignition-end thread.
X 33 917 066 — Introduction of this 066 wrap-handle modification; not a model-identification range or a cutoff for the standard flush-cut version.
- Original collar nut 0000 955 0802 is labeled M8×1; new nut 9211 260 1340 is labeled M8×10 in the original summary. Page 1 explicitly changes the ignition-end thread from M8 to M10 and labels the drawing M10.
- This original thread-label conflict is unresolved. Do not silently relabel the new nut, infer its pitch from the number, or treat M8×10 as a verified fit specification.
- The table separately removes spline screw IS-M 3.5×12, 9041 216 0540, and introduces spline screw IS-M 4×12, 9022 313 0660. The table places them in the ignition-system chapter but gives no exact attachment point or tightening torque.
- Remark 3 retains the original collar nut for older machines and 064. No comparable spare-availability remark is attached to either screw row; a dash in the new-version column is not a universal no-stock claim.
Source: TI 2/1996, p. 1 · TI 2/1996, p. 4 — 1.1 drawing/text and summary items 7,8,11,12 / remark 3.
Part numbers (4)
- 0000 955 0802 — Original collar nut M8×1Original fastener · Older 066 configuration
- 9211 260 1340 — New nut; printed M8×10 conflicts with M10 shaftUnresolved thread label · 066 revision; thread specification not verified
- 9041 216 0540 — Spline screw IS-M 3.5×12Removed table version · Original ignition-system chapter
- 9022 313 0660 — Spline screw IS-M 4×12New table version · Revised ignition-system chapter; attachment unspecified
Conditional replacement · 066
066: larger oil-tank crankcase always needs the new gasket
Crankcase 1122 020 2113 requires gasket 1122 029 0507; oil capacity rises from 315 to 360 cc.
1 45 500 383 — Production introduction for this specific modification only; not proof of an individual saw’s installed configuration.
- From serial 1 45 500 383, crankcase 1122 020 2103 is replaced by crankcase 1122 020 2113. The new oil tank holds 360 cc (12.2 fl. oz.) instead of 315 cc (10.6 fl. oz.). The source says this leaves a certain amount of chain oil in the tank; it does not quantify remaining oil or establish a runtime guarantee.
- Always use gasket 1122 029 0507 when installing crankcase 1122 020 2113. Summary item 2 changes gasket 1122 029 0500 to 1122 029 0507; the old gasket remains available for other, unnamed models (remark 2). This does not authorize the old gasket on the new crankcase.
- Previous crankcase 1122 020 2103 is no longer available from the factory (remark 1). Plug 1122 021 1900 has a dash in the New column but remains available as a spare (remark 3); no successor is supplied. New 066 gasket set 1122 007 1053 includes item 2, the new crankcase gasket; other contents are not specified.
- The extracted two-column text interleaves the crankcase paragraph with the service note. Its former automated 1122 020 2103 → 1122 029 0507 pairing is false: the latter is the required gasket, not the replacement crankcase. Original page 3 and both table rows establish the separate relationships.
- The final 01.98 reference is last-TI bibliography, not supersession. The 066 crankcase change does not establish a 064 change or share the separate 064 grommet serial.
- Historical TI52/1999 instructions and spare-availability statements are not present stock or physical interchange verification. Base-model catalog sheets are navigation anchors; printed R/M variant restrictions remain controlling. No applicability to MS 640, MS 650 or MS 660 is inferred.
Source: TI 52/1999, p. 3 — Section 3 full prose, service note, all summary rows/remarks and footer.
Part numbers (6)
- 1122 020 2103 — 066 previous crankcaseReplaced; historical factory unavailability · 066 modification as specified; exceptions explicitly stated
- 1122 020 2113 — 066 crankcase with larger oil tankNew; requires new gasket · 066 modification as specified; exceptions explicitly stated
- 1122 029 0500 — Previous crankcase gasketRetained for other unnamed models · 066 modification as specified; exceptions explicitly stated
- 1122 029 0507 — New crankcase gasketRequired with 1122 020 2113 · 066 modification as specified; exceptions explicitly stated
- 1122 021 1900 — PlugNo new number; retained spare · 066 modification as specified; exceptions explicitly stated
- 1122 007 1053 — 066 gasket setIncludes new crankcase gasket; other contents unspecified · 066 modification as specified; exceptions explicitly stated
Service note · 064 / 066
064 / 066: thirteen-roller crankshaft differs between production and service
066 gets the new crankshaft at X 29 588 002; 064 retains its production crankshaft but uses the new service replacement.
X 29 588 002 (066 production only) — Printed introduction for this component only; not a universal machine cutoff or interchange guarantee.
- Crankshaft 1122 030 0407 with newly developed big-end bearing cage increases needle rollers from TWELVE to THIRTEEN. It becomes standard in 066 production FROM X 29 588 002. This serial is NOT a 064 production changeover.
- 064 CONTINUES production with crankshaft 1122 030 0406, but 1122 030 0407 SHOULD be used for service replacement. Summary footnote says original crankshaft is no longer available FROM FACTORY; retain this spare-supply statement separately from its explicit continued 064 production use.
- No separate bearing-cage part number or permission to rebuild the old crankshaft with loose new rollers is supplied. No MS 640 / MS 660 applicability is inferred.
- Historical TI 19/1994 guidance for explicitly named models only; no successor or unlisted variant applicability inferred. Factory supply statements are historical, not current stock claims. MOQ columns are order quantities, not fitting quantities. No physical interchange test was performed.
Source: TI 19/1994, p. 1 — 064 / 066: thirteen-roller crankshaft differs between production and service.
Part numbers (2)
- 1122 030 0406 — Original twelve-roller crankshaft064 production continues; unavailable factory spare · 064 / 066: thirteen-roller crankshaft differs between production and service
- 1122 030 0407 — Thirteen-roller crankshaft066 production and 064 service replacement · 064 / 066: thirteen-roller crankshaft differs between production and service
Service note · 064 / 066
064 / 066 brake-band cover: fourth screw and smaller core hole
Cover 1122 021 1105 replaces 1101; recess changes from 4 to 3 mm.
X 31 815 798 — 064 / 066 crankcase, cover mounting and brake-spring revisions in TI27/1995; model-conditioned production change, not a universal compatibility boundary.
- From X 31 815 798, crankcase 1122 020 2101 (064) and 1122 020 2102 (066) are revised. Both crankcases KEEP THEIR PART NUMBERS; a matching number alone cannot distinguish the original and modified castings.
- Cover 1122 021 1105 replaces 1122 021 1101 and is secured with FOUR IS-M4 x 12 spline screws 9022 313 0660 instead of three. Figure 134TI004 K points to the added attachment near the brake band.
- The recess at the brake-band attachment changes from diameter 4 mm to 3 mm (printed 5/32 to 1/8 inch) and becomes the CORE HOLE for the additional mounting point. This is a production geometry change, NOT a direction to drill an existing 4-mm recess smaller. No old-case conversion or machining method is given.
- The TI says the change optimizes brake-band location; it gives no measured brake performance, screw torque or additional retrofit approval. Do not infer that the later cover alone makes every old crankcase equivalent.
- Later exact 064 A sheet lists crankcase 2101 at key1, cover 1105 at key15 and screw 0660 quantity4 at key16. Exact 066 A sheet lists crankcase 2113 at key1 AND 2102 at key32, cover 1105 at key14 and screw 0660 quantity4 at key15. These later rows do not establish a 2102-to-2113 supersession or erase the historical same-number revision.
- Historical TI guidance for the named models and stated versions only. Shared IPL sheets or series do not extend applicability to other variants or successor models. Supply statements are historical, not present stock guarantees or verified physical interchange. No hardware operation was performed.
Source: TI 27/1995, p. 1 — Section1 geometry and figure 134TI004 K.
Part numbers (5)
- 1122 020 2101 — 064 crankcasesame-number revised casting · 064 / 066; Section1 geometry and figure 134TI004 K
- 1122 020 2102 — 066 crankcasesame-number revised casting · 064 / 066; Section1 geometry and figure 134TI004 K
- 1122 021 1101 — Original coverreplaced · 064 / 066; Section1 geometry and figure 134TI004 K
- 1122 021 1105 — Four-screw covernew · 064 / 066; Section1 geometry and figure 134TI004 K
- 9022 313 0660 — Spline screw IS-M4 x 12same number; installed quantity three to four · 064 / 066; Section1 geometry and figure 134TI004 K
Service note · 064 / 066
064 / 066 crankcase supply: cover and screws through end 1998
Preserve the dated crankcase inclusion limit; MOQ cells are blank.
X 31 815 798 — 064 / 066 crankcase, cover mounting and brake-spring revisions in TI27/1995; model-conditioned production change, not a universal compatibility boundary.
- Both 064 crankcase 1122 020 2101 and 066 crankcase 1122 020 2102 are listed with original and new numbers IDENTICAL, each including summary item1 cover and item2 screw. Remark1: only MODIFIED crankcases are factory available. This does not prove that every used part bearing the number is modified.
- Cover 1122 021 1101 is replaced by 1122 021 1105, remarks2 and3. Remark2: original cover no longer factory available. Screw 9022 313 0660 keeps its number, remarks3 and4. Remark4: quantity changes from THREE TO FOUR; this is installed quantity, not an order minimum.
- Remark3 says the new version of the part WILL BE INCLUDED WITH CRANKCASE ONLY UP TO END OF 1998. It applies to both cover and screw rows. It is an inclusion deadline, NOT a claim that the cover and screws are supplied only as a crankcase kit, nor a standalone-availability promise after 1998. The four-screw mounting requirement does not expire with the supply deadline.
- All MOQ cells in this summary are BLANK; do not invent MOQ1 or MOQ4. All other parts as before. The production introduction X 31 815 798 is repeated below the table; no separate introduction date is given.
- Historical TI guidance for the named models and stated versions only. Shared IPL sheets or series do not extend applicability to other variants or successor models. Supply statements are historical, not present stock guarantees or verified physical interchange. No hardware operation was performed.
Source: TI 27/1995, p. 1 — Section1 complete summary and remarks1–4.
Part numbers (5)
- 1122 020 2101 — 064 crankcasemodified-only factory supply · 064 / 066; Section1 complete summary and remarks1–4
- 1122 020 2102 — 066 crankcasemodified-only factory supply · 064 / 066; Section1 complete summary and remarks1–4
- 1122 021 1101 — Original coverno longer factory available · 064 / 066; Section1 complete summary and remarks1–4
- 1122 021 1105 — Modified coversummary1; inclusion through end1998 · 064 / 066; Section1 complete summary and remarks1–4
- 9022 313 0660 — Spline screw IS-M4 x 12summary2; inclusion through end1998; quantity4 · 064 / 066; Section1 complete summary and remarks1–4
Service note · 066
066 ignition-end oil seal: new press sleeve 1122 893 2405
The new special tool installs the seal; it is not a seal part number or removal tool.
X 33 917 066 — TI15/1997 service-note boundary for the referenced revised 066 configuration; not a universal flush-cut/064/successor cutoff.
- Use press sleeve 1122 893 2405 (2) to INSTALL the oil seal (1) at the IGNITION END. Page 2 calls this a NEW SPECIAL TOOL and repeats its number below the separate sleeve illustration.
- Drawing 137TI023 KN shows sleeve (2) over oil seal (1); 137TI024 KN depicts the sleeve alone. The two callouts identify tool versus workpiece, not two supplied tool components. The oil seal itself has no part number on TI15/1997. No seal removal use, clutch-side use, press depth or seal-lip orientation is specified. Do not confuse press sleeve 1122 893 2405 with crankshaft screw sleeve 5910 893 2421.
- TI15/1997 applies these service notes to model 066 from machine number X 33 917 066 and explicitly refers to the TI02/1996 engineering changes: larger big-end bearing, wider-spaced crankcase bearings and lightweight flywheel. The notes supplement the 064, 066 shop manual; naming that joint manual does NOT extend the modification to 064 or MS successors.
- Scope tension retained: TI15/1997 says 066 without repeating the handle qualifier; cited TI02/1996 sections 1 and 2 say WRAP HANDLE ONLY and exclude the standard flush-cut 066 Magnum at that date. Its summary says that version changes later but gives no date or cutoff. TI15 does not establish that later introduction. Identify the revised configuration; the serial alone is not proof of universal fitment. TI02 forbids mixing old/new crank-drive parts and requires the new crankshaft AND crankcase with the lightweight flywheel.
- TI15 page 2 delegates detailed use of the special tools to the existing 064, 066 shop manual. That exact manual is not established in the verified local STIHL service documentation/owner PDF pools; detailed procedure remains a documented source gap. Later MS650/660 workshop material and the 2012 general tool catalogue are not treated as the missing historical manual. No unprinted torque, force, thread engagement, seal depth or complete repair sequence is supplied here. Last-TI08/1997 is bibliographic context, not a dependent procedure.
- Tool numbers below are transcribed from the original scans; the retained extracted text has corrupted font-encoded digits. Originals and extraction remain unchanged. Historical source guidance only; no current availability, physical interchange or hardware execution established. No hardware operation was performed.
Source: TI 15/1997, p. 1 · TI 15/1997, p. 2 — 066 ignition-end oil seal: new press sleeve 1122 893 2405.
Referenced bulletin evidence: TI 2/1996, p. 1 · TI 2/1996, p. 2 · TI 2/1996, p. 4 — Referenced configuration only: sections1.1/1.2/2.1 and summary remark2.
Part numbers (1)
- 1122 893 2405 — Press sleeve, drawing item 2New special tool; ignition-end oil-seal installation · 066 revised configuration described in TI15/1997; ignition end only where specified
Wrong number or missing part for the 066? Report a correction →