← 044/046 · MS 440/460/461

Stihl 1128 · Section D · 4 of 16 · 35 parts

Oil pump, Clutch

Fits MS 460.

Parts diagrams →

Historical fitment & changes (8) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
110111213141516171819220212222232425252626272829330456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (35)

PosPart numberDescriptionQty
1 1128 640 3206 Oil pump 0.8 Fitment / change note → → replaced by 1128 640 3250 TI 51/2003 1
2 1128 640 3250 Oil pump 1.1 Fitment / change note → 1
3 0000 958 0518 Washer 2
4 0000 997 0615 Compression spring 1
5 1128 647 0606 Pump piston 0.8 Fitment / change note → 1
6 1128 647 0602 Pump piston 1.1 Fitment / change note → 1
7 1128 647 4806 Control bolt Fitment / change note → 1
8 1128 647 4803 Control bolt Fitment / change note → 1
9 9380 620 1090 Roll pin 2x10 1
10 9646 945 0160 O-ring 4x2 2
11 1125 641 9400 Bearing bushing 1
12 1122 649 5000 Sealing ring B4x2 1
13 9022 313 0660 Spline screw IS-M4x12 2
14 1128 640 7112 Worm 1
15 1128 647 2400 Spring 1
16 1128 162 1001 Cover washer 58 mm / 2 5/16'' Fitment / change note → 1
17 1128 162 1000 Cover washer 43 mm / 1 3/4'' Fitment / change note → → replaced by 1128 162 1001, 1128 162 1001 TI 37/2001 1
18 1128 162 3202 Carrier 1
19 1128 162 0807 Clutch shoe Fitment / change note → 3
20 1128 162 3000 Retainer 3
21 0000 997 5815 Tension spring 3
22 9512 933 2380 Needle cage 10x16x12 → replaced by 9512 933 2382, 1122 967 1503 TI 53/2002 1
23 0000 642 1223 Rim sprocket 3/8" 7T 1
24 not sold separately Clutch drum not available as a separate item 1
25 0000 958 1032 Washer Ø 27 mm 1
26 9460 624 0801 E-clip 8x1.3 1
27 0000 642 1216 Rim sprocket 3/8" 8T 1
27 0000 642 1216 Rim sprocket 3/8" 8T option 1
28 0000 642 1239 NLA Rim sprocket 0.325" 9T option 1
29 1128 640 2000 NLA Chain sprocket 3/8" 7T option 1
30 1128 640 2005 Chain sprocket 3/8" 8T option 1
Not numbered on the diagram — assemblies, kits and options
— 1128 160 2004 Clutch Fitment / change note → 1
— 1128 007 1001 Rim sprocket kit 3/8" 8T 1
— 1128 007 1001 Rim sprocket kit 3/8" 8T option 1
— 1128 007 1011 Rim sprocket kit 0.325" 9T option 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Conditional replacement · MS 440 / MS 460

MS 440 / MS 460: larger cover washer requires newer clutch shoes

The 58 mm cover washer is conditional on the revised shoes, not a direct washer-only replacement for the older clutch.

  • New cover washer 1128 162 1001 (58 mm outside diameter) may only be installed with new clutch shoes 1128 162 0806.
  • Previous washer 1128 162 1000 (43 mm) is described as remaining available for older machines and clutch 1128 160 2000 with shoes 1128 162 0800 in this historical TI; this is not a current stock statement.
  • The revised clutch is 1128 160 2001 with three shoes 1128 162 0806. Its shoe shoulders provide clearance for the larger washer.
  • The word TOP on the washer must face the clutch. Introduction is in progress; no numeric cutoff is supplied.
  • This reviewed USA-edition note names MS 440 and MS 460. It does not establish a universal older 044/046 conversion.
  • The larger washer further shields the oil pump and helps protect the crankcase and oil pump from consequential damage if a clutch spring breaks. This is a stated protective purpose, not a guarantee against all damage or a remedy for a failed clutch.
  • Drawing 176TI008 KN compares the previous 43 mm (1.693 in.) washer at left with the new 58 mm (2.283 in.) washer at right. Drawing 176TI010 KN compares the old clutch shoe at left with the shouldered new shoe at right; arrows identify the revised contour for clearance. No shoe machining dimensions or modification procedure are supplied.
  • Summary item 2 includes item 3: clutch assembly with three clutch shoes. All three rows carry remark 1: the previous washer, clutch assembly and shoes remain available as spares for older machines according to this TI. Availability is historical, not a present ordering promise.
  • Historical supply discrepancy remains unresolved: TI37/2001 says the old clutch 1128 160 2000 and shoes 1128 162 0800 remain available, while TI05/2001 (MS460) and TI06/2001 (MS440) mark those previous parts no longer available from the factory. These edition statements are retained without inventing a universal stock chronology. They do not relax the new-washer/new-shoe restriction.

Source: TI 37/2001, p. 1 · TI 37/2001, p. 2 — Complete cover-washer purpose, diagrams, parts availability, TOP service note and all three summary rows.

Part numbers (6)
  • 1128 162 1000 — 43 mm cover washerPrevious configuration · Older clutch 1128 160 2000 / shoes 1128 162 0800
  • 1128 162 1001 — 58 mm cover washerConditional replacement · Only with shoes 1128 162 0806
  • 1128 160 2000 — Clutch assemblyPrevious configuration · MS 440 / MS 460 older assembly
  • 1128 160 2001 — Clutch assemblyRevised configuration · MS 440 / MS 460 with new shoes
  • 1128 162 0800 — Clutch shoePrevious version · Older clutch; old cover washer
  • 1128 162 0806 — Clutch shoeRequired companion; three · Required for larger cover washer

Conditional replacement · MS 460

MS 460 transition: revised clutch and shoes

TI 05/2001 pairs revised clutch 1128 160 2001 with shoes 1128 162 0806; later TI 37/2001 adds washer fitting conditions.

Later reviewed guidance: MS 440 / MS 460: larger cover washer requires newer clutch shoes

  • Previous clutch 1128 160 2000 uses shoes 1128 162 0800; new clutch 1128 160 2001 uses shoes 1128 162 0806.
  • The table includes the shoe item in the clutch assembly. Introduction is in progress; no serial cutoff is given.
  • Read later TI 37/2001 before selecting the cover washer: its larger washer is restricted to the new shoes and has an orientation requirement.
  • This MS 460 transition record does not by itself approve a complete conversion of every older 046 clutch configuration.
  • Summary items 8 and 9 both carry remark 1: the previous clutch and previous shoe are no longer available from the factory at the time of this TI. This is historical supply information, not current stock or permission to mix shoe generations.
  • Section 6 announces a separate illustrated parts list and its inclusion in the 01.2001 microfiche/CD-ROM issue. This bibliographic statement does not identify the edition of the current catalog overlay or substitute for the later washer conditions. Retained TI is english / USA.

Source: TI 5/2001, p. 1 · TI 5/2001, p. 2 · TI 5/2001, p. 3 · TI 5/2001, p. 4 — Complete sections 1–7: 046/MS460 naming, cap operation, tank and crankcase matching assemblies, vent construction/function, clutch and all summary rows.

Part numbers (4)
  • 1128 160 2000 — ClutchPrevious version · MS 460 transition predecessor
  • 1128 160 2001 — ClutchRevised version · MS 460 with new shoes
  • 1128 162 0800 — Clutch shoePrevious configuration · Clutch 1128 160 2000
  • 1128 162 0806 — Clutch shoeRevised configuration · Clutch 1128 160 2001

Service note · MS 460

MS 460 high-output oil pump: wrap-handle serial cutoff, optional retrofit

Production introduction and optional all-MS460 fitment are different claims.

1 61 013 422 — Production change from this number on MS 460 with wrap-around handle only; optional retrofit to other MS 460 models is separate.

  • From serial number 1 61 013 422, pump 1128 640 3206 is replaced by 1128 640 3250 on the MS 460 WITH WRAP-AROUND HANDLE. Page 2 gives the equivalent handover condition greater than 1 61 013 421. The serial boundary is not a claim that every MS 460 after that number has the high-output pump.
  • Separately, the new 3250 is announced as a future OPTIONAL SPECIAL ACCESSORY for ALL MS 460 models. This permits the stated historical retrofit application; it does not make the wrap-handle production change universal or establish current availability.
  • The new pump differs from the old only in adjusting screw 1128 647 4803 and pump piston 1128 647 0602. The summary identifies previous screw 1128 647 4806 and piston 1128 647 0606; the pump assembly includes both items. All other parts remain as before. No mixed old/new screw-and-piston combination is verified by this statement.
  • All three previous versions remain available for older machines and other models in the historical summary; those other models are not named. The bibliography names TI32/2003 as the preceding MS 460 TI; it does not contradict TI40/2003’s existence or establish a single region-independent publication sequence. Footer supplies provenance only.
  • Mandatory handover context for this fitment: in high-output range b, the oil tank may empty before the fuel tank. Refill oil when the fuel tank is roughly half-full, and explain the need for more frequent oil checking/refilling on qualifying wrap-handle machines and every 3250 retrofit.
  • Historical TI51/2003 English USA guidance for the exact MS 460 oil-pump configuration described; no application to 046, MS 440 or other models is inferred. No physical interchange test was performed.

Source: TI 51/2003, p. 1 · TI 51/2003, p. 2 — Production introduction; handover/retrofit; complete summary and remarks.

Part numbers (6)
  • 1128 640 3206 — Previous oil pumpPrevious assembly; retained supply · MS 460; exact production or retrofit scope stated above
  • 1128 640 3250 — Higher-output oil pumpNew assembly including screw and piston · MS 460; exact production or retrofit scope stated above
  • 1128 647 4806 — Previous adjusting screwPrevious pump component · MS 460; exact production or retrofit scope stated above
  • 1128 647 4803 — New adjusting screwHigher-output pump component · MS 460; exact production or retrofit scope stated above
  • 1128 647 0606 — Previous pump pistonPrevious pump component · MS 460; exact production or retrofit scope stated above
  • 1128 647 0602 — New pump pistonHigher-output pump component · MS 460; exact production or retrofit scope stated above

Service note · MS 460

MS 460 high-output oiling: refill oil at roughly half a fuel tank

Range b can empty the oil tank before the fuel tank; range a remains near the old delivery rate.

  • The new pump 1128 640 3250 delivers UP TO 0.2 oz. (7 cm³) MORE oil per minute, advantageous with long guide bars in hard and dry timber. These are the source’s paired rounded quantities, not an exact unit conversion or total pump output. No test speed, oil viscosity, temperature, numeric tank capacity or guaranteed runtime is supplied.
  • In illustrated RANGE a, delivery is ALMOST IDENTICAL to the previous pump, not a precise measured equality. RANGE b is the higher-output portion beyond a shown in the original adjustment diagram. The E marking is visible, but no numeric angle, flow calibration or definition of E is stated here; do not invent one.
  • In RANGE b the oil tank MAY EMPTY BEFORE THE FUEL TANK and the chain may run dry. The explicit prevention instruction is REFILL THE OIL TANK WHEN THE FUEL TANK IS ROUGHLY HALF-FULL. This is not an instruction to run either tank dry or a promise that a fixed elapsed time is safe.
  • At handover, particularly draw attention to checking/refilling oil more frequently for wrap-handle MS 460 machines above 1 61 013 421, and whenever 3250 is retrofitted to an MS 460. Preserve this warning with the retrofit fitment result, rather than presenting increased delivery as an unconditional upgrade.
  • Historical TI51/2003 English USA guidance for the exact MS 460 oil-pump configuration described; no application to 046, MS 440 or other models is inferred. No physical interchange test was performed.

Source: TI 51/2003, p. 1 · TI 51/2003, p. 2 — Oil delivery/oil tank capacity; range diagram; handover warnings.

Part numbers (1)
  • 1128 640 3250 — Higher-output oil pumpRange-b oil depletion warning · MS 460; exact production or retrofit scope stated above

Service note · MS 460

MS 460 pump identification: transverse screw groove and circumferential piston groove

Two distinct visible marks identify the changed components.

  • New adjusting screw 1128 647 4803 has a groove AT RIGHT ANGLES TO THE SLOT in its head, as the arrowed head-on view shows. The ordinary screwdriver slot alone is not the distinguishing feature. The summary’s previous screw is 1128 647 4806.
  • New piston 1128 647 0602 has a groove around its FULL CIRCUMFERENCE at the illustrated pump-piston feature. This is distinct from the adjusting screw’s transverse head groove. The summary’s previous piston is 1128 647 0606.
  • Use the original figures and exact identities; no groove dimensions, machining instructions or authorization to modify old components is given. A single visible feature does not verify the entire assembled pump or its measured oil delivery.
  • Historical TI51/2003 English USA guidance for the exact MS 460 oil-pump configuration described; no application to 046, MS 440 or other models is inferred. No physical interchange test was performed.

Source: TI 51/2003, p. 2 — Distinguishing features; both illustrations; summary component identities.

Part numbers (4)
  • 1128 647 4803 — New adjusting screwTransverse head groove · MS 460; exact production or retrofit scope stated above
  • 1128 647 4806 — Previous adjusting screwPrevious identity · MS 460; exact production or retrofit scope stated above
  • 1128 647 0602 — New pump pistonFull circumferential groove · MS 460; exact production or retrofit scope stated above
  • 1128 647 0606 — Previous pump pistonPrevious identity · MS 460; exact production or retrofit scope stated above

Service note · MS 460

MS 460 higher-output pump retrofit: optional service, not a warranty conversion

The historical service policy does not establish today’s price or warranty entitlement.

  • The source describes conversion from the standard/previous pump to the higher-output pump as an OPTION at ADDITIONAL COST, and says it should NOT be claimed as a warranty repair. Preserve this as the vendor’s 2003 service-policy statement, not a current price, legal conclusion or determination of present warranty rights.
  • The all-MS460 optional accessory statement is separate from the serial-bound wrap-handle production introduction. Retrofitting 1128 640 3250 requires the explicit more-frequent oil-check/refill handover warning: in high-output range b, refill oil at roughly half a fuel tank.
  • This TI identifies the pump and its two changed components, but supplies no removal/refit sequence or installation torque. It is not a complete workshop installation procedure and does not establish mixed-component conversions or cross-model interchange.
  • Historical TI51/2003 English USA guidance for the exact MS 460 oil-pump configuration described; no application to 046, MS 440 or other models is inferred. No physical interchange test was performed.

Source: TI 51/2003, p. 1 · TI 51/2003, p. 2 — Optional accessory; maintenance/repair; handover.

Part numbers (1)
  • 1128 640 3250 — Optional higher-output oil pumpHistorical paid retrofit; oil refill warning required · MS 460; exact production or retrofit scope stated above

Service note · MS 440 / MS 460 / MS 361 / MS 361 C

MS 440, MS 460 and MS 361 clutch change with guide strips

New complete clutch retrofits; individual shoe mixing is prohibited.

  • Previous clutch 1128 160 2001 with shoes 1128 162 0806 is replaced by clutch 1128 160 2004 with shoes 1128 162 0807. Mutually engaging guide strips improve lateral guidance, reducing shoe tilt, wear between shoe and carrier, and idle noise.
  • New complete clutch 1128 160 2004 may also be installed in older machines in the stated model scope. Introduction is CONTINUOUS: NO NUMERIC SERIAL CUTOFF is supplied. Other individual parts remain unchanged.
  • Previous complete clutch is no longer factory-available according to the historical summary; old shoe 1128 162 0806 remains available for the previous clutch and other model series. This is 2005 supply policy, not present stock availability. Observe the separate no-mixing/pairing restriction; do not infer a single-shoe retrofit.
  • Historical TI36/2005 English USA guidance only; the linked catalog sheets are navigation anchors, not proof that all later variants share these specifications. No physical interchange test was performed.

Source: TI 36/2005, p. 1 · TI 36/2005, p. 2 · TI 36/2005, p. 3 — MS 440, MS 460 and MS 361 clutch change with guide strips.

Part numbers (4)
  • 1128 160 2001 — Previous clutchReplaced complete assembly · MS 440, MS 460, MS 361, MS 361 C; see note restrictions
  • 1128 160 2004 — New clutchComplete assembly also fits older stated machines · MS 440, MS 460, MS 361, MS 361 C; see note restrictions
  • 1128 162 0806 — Previous clutch shoeRetained for previous clutch/other series · MS 440, MS 460, MS 361, MS 361 C; see note restrictions
  • 1128 162 0807 — Guide-strip clutch shoeNew design; no mixing with old shoes · MS 440, MS 460, MS 361, MS 361 C; see note restrictions

Service note · MS 440 / MS 460 / MS 361 / MS 361 C

Clutch shoe retrofit: no mixed designs; printed pairing remains ambiguous

The source says “in pairs” without giving an assembly count.

  • New shoe 1128 162 0807 CANNOT BE COMBINED with previous shoe 1128 162 0806. The next sentence says new shoes can only be fitted in the previous clutch “in pairs” because of the guide strips.
  • Preserve BOTH statements. The illustration shows engagement between neighboring guide strips; it does not specify a complete clutch shoe count. Do not interpret “in pairs” as permission for two new shoes plus one old shoe, silently rewrite it as a stated three-shoe set, or invent a mixed-clutch assembly procedure.
  • Exact individual-shoe retrofit quantity remains unresolved in this source. The explicit complete-clutch retrofit is separate and does not depend on guessing that quantity. Old shoes remain historically available for the previous clutch and other series; availability is not permission to mix designs.
  • Historical TI36/2005 English USA guidance only; the linked catalog sheets are navigation anchors, not proof that all later variants share these specifications. No physical interchange test was performed.

Source: TI 36/2005, p. 1 · TI 36/2005, p. 2 · TI 36/2005, p. 3 — Clutch shoe retrofit: no mixed designs; printed pairing remains ambiguous.

Part numbers (2)
  • 1128 162 0806 — Previous shoeCannot be mixed with guide-strip shoe · MS 440, MS 460, MS 361, MS 361 C; see note restrictions
  • 1128 162 0807 — Guide-strip shoePrinted pairing ambiguity; no mixed designs · MS 440, MS 460, MS 361, MS 361 C; see note restrictions

Wrong number or missing part for the MS 460? Report a correction →